One of the user complained that on his system Thinkpad Yoga S1, with
commit f1664eaace ("iio: hid-sensor-trigger: Fix the race with user
space powering up sensors") causes the system to resume immediately
on suspend (S3 operation). On this system the sensor hub is on USB
and is a wake up device from S3. So if any sensor sends data on
motion, the system will wake up. This can be a legitimate use case
to wake up device motion, but that needs proper user space support
to set right thresholds.
In fact the above commit didn't cause this regression, but any operation
which cause sensors to wake up would have caused the same issue. So if
user reads the raw sensor data, same issue occurs, with or without this
commit. Only difference is that the above commit by default will trigger
a power up and power down of sensors as part of runtime pm enable
(runtime enable will cause a runtime resume callback followed by
runtime_suspend callback). Previously user has to do some action on
sensors.
On investigation it was observed that the current driver correctly
changing the state of all sensors to power off but then also some sensor
will still send some data. Only option is to never power up any sensor.
Only good option is to:
- Using sysfs interface disable USB as a wakeup device (This will not
need any driver change)
Since some user don't care about sensors. So for those users this change
brings back old functionality. As long as they don't cause any operation
to power up sensors (like raw read or start iio-sensor-proxy service),
the sensors will not be to touched. This is done by delaying run time
enable till user space does some operation with sensors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196853
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Pull HID update from Jiri Kosina:
- Wacom driver fixes/updates (device name generation improvements,
touch ring status support) from Jason Gerecke
- T100 touchpad support from Hans de Goede
- support for batteries driven by HID input reports, from Dmitry
Torokhov
- Arnd pointed out that driver_lock semaphore is superfluous, as driver
core already provides all the necessary concurency protection.
Removal patch from Binoy Jayan
- logical minimum numbering improvements in sensor-hub driver, from
Srinivas Pandruvada
- support for Microsoft Win8 Wireless Radio Controls extensions from
João Paulo Rechi Vita
- assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (28 commits)
HID: prodikeys: constify snd_rawmidi_ops structures
HID: sensor: constify platform_device_id
HID: input: throttle battery uevents
HID: usbmouse: constify usb_device_id and fix space before '[' error
HID: usbkbd: constify usb_device_id and fix space before '[' error.
HID: hid-sensor-hub: Force logical minimum to 1 for power and report state
HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
HID: asus: Add T100CHI bluetooth keyboard dock touchpad support
HID: ntrig: constify attribute_group structures.
HID: logitech-hidpp: constify attribute_group structures.
HID: sensor: constify attribute_group structures.
HID: multitouch: constify attribute_group structures.
HID: multitouch: use proper symbolic constant for 0xff310076 application
HID: multitouch: Support Asus T304UA media keys
HID: multitouch: Support HID_GD_WIRELESS_RADIO_CTLS
HID: input: optionally use device id in battery name
HID: input: map digitizer battery usage
HID: Remove the semaphore driver_lock
HID: wacom: add USB_HID dependency
HID: add ALWAYS_POLL quirk for Logitech 0xc077
...
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Clearly this set jumps across multiple areas, but inherently it
can't be grouped like the other sets in this series so I've done
all the stuff in the common directory together.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the reference HID sensor hub firmware all Named array enums were
0-based. There is no description of the default base of enums in HID
sensor hub specification as logical minimum should have set this base
value.
Every sensor hub implemented enum as 1-based, without explicitly setting
logical minimum to 1, because of the implementation by one of the major
OS vendor. In Linux we used logical minimum to decide the enum base.
Some sensor hub FWs already changed logical minimum from 0 to 1. We hoped
that every other vendor will follow. But that didn't happen and we had to
fix the report header for every sensor hub to change logical minimum to 1
by using .report_fixup() callback. So for every new sensor hub we had to
modify source code by adding this quirk based on the vendor and device id.
This is becoming a maintenance burden.
This patch hardcodes the logical minimum of power and report state
attributes to 1. In this way we can remove the existing quirks and also
we don't have to add more quirks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Building a kernel with my configuration failed with:
> drivers/built-in.o: In function `hid_sensor_setup_batch_mode': staging/drivers/iio/common/hid-sensors/hid-sensor-trigger.c:104: undefined reference to `iio_buffer_set_attrs'
which is fixed by this patch.
Signed-off-by: Alexander Wuerstlein <arw@arw.name>
Fixes: 138bc7969c ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hubs using Integrated Senor Hub (ISH) has added capability to
support batch mode. This allows host processor to go to sleep for extended
duration, while the sensor hub is storing samples in its internal buffers.
'Commit f4f4673b75 ("iio: add support for hardware fifo")' implements
feature in IIO core to implement such feature. This feature is used in
bmc150-accel-core.c to implement batch mode. This implementation allows
software device buffer watermark to be used as a hint to adjust hardware
FIFO.
But HID sensor hubs don't allow to change internal buffer size of FIFOs.
Instead an additional usage id to set "maximum report latency" is defined.
This allows host to go to sleep upto this latency period without getting
any report. Since there is no ABI to set this latency, a new attribute
"hwfifo_timeout" is added so that user mode can specify a latency.
This change checks presence of usage id to get/set maximum report latency
and if present, it will expose hwfifo_timeout.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add orientation sensor "scale" and "offset" parse support.
These two properties are needed for exponent data conversion.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.
Fixes: 5d9854eaea ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAljw8ScRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FojZvBAAh8K9e+3ObpS6/0wj26/XsakiFn4v2ah0
xKUnafxAVVxU3AU01IJ3CtNdIMyqMwpnB+PvnpgDzZw749QrYKPsBIzheK64eabe
fzA34X5MWGLwUdOXpfEB0xvsylWjJrqsf1rahgZjiUKkPeZe9EwzPM/fP1sEl5gu
p+vfSMckboFaKheoQwnWMUTBp0HK+nbFpcSBzljX68u+epiXpDGrjuZC8NJ3JuBn
Bloz9AhDliIn477H7mIUTXBbt3ixLIDiJ7haQuTNlagosPoUtCBpwY2O9mZ7VRVs
wM62h7/F170077ReQJRjlfck+7uHoIgDeS46w5UYTzA1HJLxs+veO5xv3VOtHIUg
BZ+mibQyIUBrFeyYDVbeUpBTffiU6rA+yiM4WFwUFabl7t7rlG0NhLEx7OIQcFMm
l8u/5JUoJcoykaO8c9Jx5XtrgkXq+rCWVAmhjHqUDAlvsMa6pJWEyqgaVcQeIbdw
ns9ppJRlOmEst7lMab9TI7BJp3oCIH6uRmctbme42Rw8XgDFdltxqkxmjB8d+cDC
Q0INhNJN1jRgz6rT6lkxVhAYKtaP5T8qZeliT4MO1E59ggOVSSf8zuhjrEMUK397
Tu/k7fmATtiKSG+blwYZVRC3+ixh/oKZsvfwZ4O+mFJyhQ616nKMYAywoaZcM8WT
Z1ABipUDwsE=
=H5KS
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
-----BEGIN PGP SIGNATURE-----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=zHqs
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fourth set of IIO new device support, features and cleanups for the 4.12 cycle
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
When a hid sensor module is removed and modprobed again we see
error for unbalanced pm_runtime. This issue is caused by not
deactivating runtime PM on removal. So on modprobe again when
activated again, this will print this error.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change undo the change done by 'commit 3bec247474
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec247474 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
-----BEGIN PGP SIGNATURE-----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=YYdq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Third set of new device support, cleanups and features for IIO in the 4.12 cycle
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
When system bootup without get sensor property, set sensor
property will be fail.
If no get_feature operation done before set_feature, the sensor
properties will all be the initialized value, which is not the
same with sensor real properties. When set sensor property it will
write back to sensor the changed perperty data combines with other
sensor properties data, it is not right and may be dangerous.
In order to get all sensor properties, choose to read one of the sensor
properties(no matter read any sensor peroperty, driver will get all
the peroperties and return the requested one).
Fixes: 73c6768b71 ("iio: hid-sensors: Common attribute and trigger")
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental humidity sensor is a hid defined sensor,
it shows raw humidity measurement of air.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, humidityrelative data output unit is
milli percent. Add the unit convert from percent to milli percent.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Scale value include two parts: unit conversion and exponent conversion.
Add gravity unit convert table to fix gravity sensor scale value not
right issue.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental temperature sensor is a hid defined sensor,
it measures temperature.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, IIO_TEMP data output unit is
milli degrees Celsius. Add the unit convert from degree to milli degree.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added timestamp channel. With this change, each sample has a timestamp.
This timestamp can be from the sensor hub when present or local kernel
timestamp. HID sensors can send timestamp with input data using usage id
HID_USAGE_SENSOR_TIME_TIMESTAMP. This timestamp value is converted to
nano seconds before pushing this sample to the iio core.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While testing, it was observed that on some platforms the scale value
from iio sysfs for gyroscope is always 0 (E.g. Yoga 260). This results
in the final angular velocity component values to be zeros.
This is caused by insufficient precision of scale value displayed in sysfs.
If the precision is changed to nano from current micro, then this is
sufficient to display the scale value on this platform.
Since this can be a problem for all other HID sensors, increase scale
precision of all HID sensors to nano from current micro.
Results on Yoga 260:
name scale before scale now
--------------------------------------------
gyro_3d 0.000000 0.000000174
als 0.001000 0.001000000
magn_3d 0.000001 0.000001000
accel_3d 0.000009 0.000009806
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Neither sample frequency value nor hysteresis value can be set to be a
negative number, check and return "Invalid argument" if they are negative.
If not do this change, sample_frequency will be set into some unknown
value, read hysteresis value after write negative number will return
"Invalid argument".
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
According to IIO ABI definition, IIO_PRESSURE data output unit is
kilopascal:
http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio
This patch fix output unit of HID pressure sensor IIO driver from pascal to
kilopascal to follow IIO ABI definition.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A small rework of the PM code in this driver introduced a harmless
warning when CONFIG_PM_SLEEP is not set:
drivers/iio/common/hid-sensors/hid-sensor-trigger.c:212:12: error: 'hid_sensor_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead marks all three PM functions
as __maybe_unused, which covers all possible cases and is harder
to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7f6cf74145 ("iio: hid-sensors: use asynchronous resume")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some platforms power off sensor hubs during S3 suspend, which will require
longer time to resume. This hurts system resume time, so resume
asynchronously.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By default all the sensors are runtime suspended state (lowest power
state). During Linux suspend process, all the run time suspended
devices are resumed and then suspended. This caused all sensors to
power up and introduced delay in suspend time, when we introduced
runtime PM for HID sensors. The opposite process happens during resume
process.
To fix this, we do powerup process of the sensors only when the request
is issued from user (raw or tiggerred). In this way when runtime,
resume calls for powerup it will simply return as this will not match
user requested state.
Note this is a regression fix as the increase in suspend / resume
times can be substantial (report of 8 seconds on Len's laptop!)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Len Brown <len.brown@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Current API only allows setting one offset in the field. This API
is extended to set multiple offsets in the field report.
Also update parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hid sensor feature report can contain more than one reports.
This API can now support receiving multiple values from the feature
report.
Also update the parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To improvement power and performance, both regular and run time callbacks
are introduced. Because of auto suspend delay, two consecutive read
don't have to go through full power on/off procedure. The auto suspend
time can be adjusted using regular power attributes of PM sysfs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
This fixes the following sparse warning:
CHECK drivers/iio/common/hid-sensors/hid-sensor-attributes.c
drivers/iio/common/hid-sensors/hid-sensor-attributes.c:346:5: warning:
symbol 'hid_sensor_get_reporting_interval' was not declared. Should it be static?
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move the 'static' keyword to beginning of definition to silence the
following compilation warning:
drivers/iio/common/hid-sensors/hid-sensor-attributes.c:34:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RuB2
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.16 cycle.
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
Some sensor hubs require a get feature report call to be issued soon after
changing the power state of the sensor. Without this, the sensor remains in
the current state. This patch adds a call soon after the power state.
This is retained as a generic call across all sensor hubs since the behavior
has been noticed on more than one implementation.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For PROP_REPORT_INTERVAL, the spec does not mandate the presence
of the report interval unit in the feature report and expects the
default unit of measure to be used as milliseconds.
Currently, when the unit is not present, it gets set as zero leading
to issues in sampling frequency.
This patch sets the unit of measure to the default unit if it
is not defined by firmware.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The "i < " was missing in this condition.
Fixes: 5d02edfc39 ('iio: hid-sensors: Convert units and exponent')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added interface to get poll value in milli-seconds. This value is
changed by changing sampling frequency. This API allows clients
to wait for at least some poll milli seconds before reading a new sample.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hub specify a default unit and alternative units. This
along with unit exponent can be used adjust scale. This change
change HID sensor data units to IIO defined units for each
sensor type. So in this way user space can use a simply use:
"(data + offset) * scale" to get final result.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove the hard coded indexes, instead search for usage id and
use the index to set the power and report state.
This will fix issue, where the report descriptor doesn't contain
the full list of possible selector for power and report state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We can't store the trigger instance created by iio_trigger_alloc, in
trig field of iio_device structure. This needs to be stored in the
driver private data. Othewise it can result in crash during module
unload. Hence created a trig_ptr in the common data structure
for each HID sensor IIO driver and storing here.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Srinivas Pandruvada