This patch adds support for the Phicomm N1. This device based on P230 reference design.
And this box doesn't have cvbs, so disable related section in device tree.
Signed-off-by: He Yangxuan <yangxuan8282@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Try to add basic DT support for the Amlogic's Meson-G12A S905D2 SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Tanix TX3 Mini is a TV box based on the Amlogic S905W chipset.
There are two variants:
- 1 GiB or 2 GiB of DDR3 memory
- 8 GB or 16 GB eMMC flash
Both variants come with:
- 802.11 b/g/n wifi (Silicon Valley Microelectronics SSV6051, does not
support Bluetooth)
- an LED 7 segment display with an FD628 controller
- HDMI and AV (CVBS) output
- 2x USB (utilizing both USB ports provided by the SoC)
- micro SD card slot
- serial console (uart_AO) has to be soldered after opening the case
The board seems to be very similar to the P23x and Q20x reference
boards, which is why it includes meson-gx-p23x-q20x.dtsi:
- eMMC reset routed to BOOT_9
- the SDIO wifi chip's reset line is routed to GPIOX_6 and the reference
clock is 32.768KHz on PWM_E
- SD card detection is routed to CARD_6
- vqmmc of all MMC controllers is hard-wired to 1.8V (VDDIO_BOOT)
- uart_AO can be accessed after opening the case and soldering RX, TX
and GND lines onto the exposed solder points (marked with RX, TX and
GND)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
S905W is a new SoC from the GXL series. It is a cost-reduced version of
the S905X.
The P281 development board from Amlogic uses the same layout as the P231
(S905D development board). Thus the new P281 board inherits
meson-gx-p23x-q20x.dtsi to avoid code-duplication.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic P241 board is the Reference Design board for the S805X
variant of the Amlogic Meson GXL SoC family.
The P241 board has the following features :
- 1GiB DDR4 Memory
- HDMI Connector with CEC
- A/V jack with Stereo Audio and CVBS
- 10/100 Ethernet
- 2x USB2.0 Type-A
- On-board WiFi SDIO Module
- On-board eMMC storage
- Infraread Received
- Factory Reset button
- UART connector
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Try to add basic DT support for the Amlogic's Meson-AXG A113D SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Tronsmart Vega S96 is a TV box derived from Amlogic q200 reference design.
Cc: support@tronsmart.com
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM2 is a Single Board Computer, respin of the origin
Khadas VIM board, using an Amlogic S912 SoC and more server oriented.
It provides the same external connectors and header pinout, plus a SPI
NOR Flash, a reprogrammable STM8S003 MCU, FPC Connector, Cooling FAN header
and Pogo Pads Arrays.
Cc: Gouwa <gouwa@szwesion.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the CC board from Shenzhen Libre Technology
More information about the board are available here:
https://libre.computer/blog/
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The FriendlyARM NanoPi K2 is a single-board computer.
Cc: techsupport@friendlyarm.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The R-Box Pro is a TV box derived from Amlogic q200 reference design.
It uses an AP6255 Wifi module. It features an LED tube that lights a
surrounding stripe and the top logo in blue or red or pink'ish - blue
is on by default, and red (i.e., pink) is configured as panic indicator.
This device is available in at least two models, with 2 GB vs. 3 GB RAM
as well as varying eMMC size. The intent is to handle this with a single
.dts that gets the actual RAM size from U-Boot.
Cc: ada@kingnoval.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sort the .dtb files alphabetically to make clear where to add new ones.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM series consists of two boards which are almost
identical:
They are both using the same GXL S905X SoC, 100Mbit/s ethernet
(through the SoC-internal PHY), 2GB DDR3 memory, a micro-SD card slot,
onboard eMMC, Broadcom based SDIO WIFI, 2x USB A and 1x USB Type-C (the
latter with OTG support). The red LED is driven by PWM_AO_B (which
allows dimming), while the blue LED is managed by the firmware.
The differences are:
- the VIM Pro has a 16GB eMMC module, while the VIM only has 8GB
- the VIM Pro uses an AP6255 a/b/g/n/ac WIFI module, while the VIM comes
with an AP6212 b/g/n SDIO WIFI module
(the Vim uses an 8GB eMMC module, while
The boards are based on Amlogic's GXL S905X P212 reference design, which
is why most of the functionality (all MMC controllers and power
sequences, IR remote input, the main UART, ADC and ethernet) is simply
inherited from meson-gxl-s905x-p212.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the HwaCom AmazeTV set-top-box. The
hardware configuration is really similar to the other GXL boards but
for this hardware we need to limit the max-frequency of the eMMC to
have it working.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the GXL family has S905X and S905D SoCs, we're keeping the SoC
name in the DTS filename for clarity. Rename this file accordingly to
be consistent with the rest of the GXL DTS files.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Adds support for the WeTek Hub and Play2 boards.
The Hub is an extremely small IPTv Set-Top-Box and the Play2 is a more
traditionnal Satellite or Terrestrial and IPTv Set-Top-Box.
Both are based on the p200 Reference Design and out-of-tree support is
based on LibreELEC kernel at [1].
[1] https://github.com/wetek-enigma/linux-amlogic
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to keep consistency naming with the Nexbox A1 DTS file, remove the
S912 SoC name in the GXM DT files.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Nexbox A95X exists with a Meson GXBB (S905) Soc or a Meson GXL SoC (S905X).
Add the S905X variant which uses the internal PHY instead of an external PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the Nexbox A1 board based on the Amlogic S912 SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: replace '_' in node-names with '-']
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Following the Amlogic Linux kernel, it seem the only differences
between the GXL and GXM SoCs are the CPU Clusters.
This commit renames the gxl-s905d-p23x DTSI in a common file for
S905D p23x and S912 q20x boards.
Then adds a meson-gxm dtsi and reproduce the P23x to Q20x boards
dts files since the S905D and S912 SoCs shares the same pinout
and the P23x and Q20x boards are identical.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the S905 (GXBB) version of the Nexbox A95X.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add minimal DT files for the Amlogic P20x development boards, based on
the Amlogic S905/GXBB SoC.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add minimal DT files for the Hardkernel ODROID-C2 board based on the
Amlogic S905/GXBB SoC.
Used the other gxbb boards from Andreas Färber as a starting point.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
He Yangxuan