This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.
Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;
Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.
Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).
Internal key state machine:
Attach Align(RX)
+-+ +-+
| V | V
+---------+ Attach +---------+
| IDLE |---------------->| PENDING |(user = 0)
+---------+ +---------+
A A Switch| A
| | | |
| | Free(switch/revoked) | |
(Free)| +----------------------+ | |Timeout
| (TX) | | |(RX)
| | | |
| | v |
+---------+ Switch +---------+
| PASSIVE |<----------------| ACTIVE |
+---------+ (RX) +---------+
(user = 1) (user >= 1)
The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:
echo 0xfff1 > /proc/sys/net/tipc/max_tfms
The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:
+----------------------------------------------------------+
| TIPCv7 encryption | Original TIPCv2 | Authentication |
| header | packet (encrypted) | Tag |
+----------------------------------------------------------+
The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.
By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.
MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC link object:
trace_tipc_link_timeout()
trace_tipc_link_fsm()
trace_tipc_link_reset()
trace_tipc_link_too_silent()
trace_tipc_link_retrans()
trace_tipc_link_bc_ack()
trace_tipc_link_conges()
And the traces for PROTOCOL messages at building and receiving:
trace_tipc_proto_build()
trace_tipc_proto_rcv()
Note:
a) The 'tipc_link_too_silent' event will only happen when the
'silent_intv_cnt' is about to reach the 'abort_limit' value (and the
event is enabled). The benefit for this kind of event is that we can
get an early indication about TIPC link loss issue due to timeout, then
can do some necessary actions for troubleshooting.
For example: To trigger the 'tipc_proto_rcv' when the 'too_silent'
event occurs:
echo 'enable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_too_silent/trigger
And disable it when TIPC link is reset:
echo 'disable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_reset/trigger
b) The 'tipc_link_retrans' or 'tipc_link_bc_ack' event is useful to
trace TIPC retransmission issues.
In addition, the commit adds the 'trace_tipc_list/link_dump()' at the
'retransmission failure' case. Then, if the issue occurs, the link
'transmq' along with the link data can be dumped for post-analysis.
These dump events should be enabled by default since it will only take
effect when the failure happens.
The same approach is also applied for the faulty case that the
validation of protocol message is failed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We see the following scenario:
1) Link endpoint B on node 1 discovers that its peer endpoint is gone.
Since there is a second working link, failover procedure is started.
2) Link endpoint A on node 1 sends a FAILOVER message to peer endpoint
A on node 2. The node item 1->2 goes to state FAILINGOVER.
3) Linke endpoint A/2 receives the failover, and is supposed to take
down its parallell link endpoint B/2, while producing a FAILOVER
message to send back to A/1.
4) However, B/2 has already been deleted, so no FAILOVER message can
created.
5) Node 1->2 remains in state FAILINGOVER forever, refusing to receive
any messages that can bring B/1 up again. We are left with a non-
redundant link between node 1 and 2.
We fix this with letting endpoint A/2 build a dummy FAILOVER message
to send to back to A/1, so that the situation can be resolved.
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some virtual environments we observe a significant higher number of
packet reordering and delays than we have been used to traditionally.
This makes it necessary with stricter checks on incoming link protocol
messages' session number, which until now only has been validated for
RESET messages.
Since the other two message types, ACTIVATE and STATE messages also
carry this number, it is easy to extend the validation check to those
messages.
We also introduce a flag indicating if a link has a valid peer session
number or not. This eliminates the mixing of 32- and 16-bit arithmethics
we are currently using to achieve this.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch infrastructures produce huge amounts of packet duplicates.
This becomes a problem if those messages are STATE/NACK protocol
messages, causing unnecessary retransmissions of already accepted
packets.
We now introduce a unique sequence number per STATE protocol message
so that duplicates can be identified and ignored. This will also be
useful when tracing such cases, and to avert replay attacks when TIPC
is encrypted.
For compatibility reasons we have to introduce a new capability flag
TIPC_LINK_PROTO_SEQNO to handle this new feature.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 32-bit node address is generated from a 128-bit identifier,
there is a risk of collisions which must be discovered and handled.
We do this as follows:
- We don't apply the generated address immediately to the node, but do
instead initiate a 1 sec trial period to allow other cluster members
to discover and handle such collisions.
- During the trial period the node periodically sends out a new type
of message, DSC_TRIAL_MSG, using broadcast or emulated broadcast,
to all the other nodes in the cluster.
- When a node is receiving such a message, it must check that the
presented 32-bit identifier either is unused, or was used by the very
same peer in a previous session. In both cases it accepts the request
by not responding to it.
- If it finds that the same node has been up before using a different
address, it responds with a DSC_TRIAL_FAIL_MSG containing that
address.
- If it finds that the address has already been taken by some other
node, it generates a new, unused address and returns it to the
requester.
- During the trial period the requesting node must always be prepared
to accept a failure message, i.e., a message where a peer suggests a
different (or equal) address to the one tried. In those cases it
must apply the suggested value as trial address and restart the trial
period.
This algorithm ensures that in the vast majority of cases a node will
have the same address before and after a reboot. If a legacy user
configures the address explicitly, there will be no trial period and
messages, so this protocol addition is completely backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we send broadcasts in clusters of more 70-80 nodes, we sometimes
see the broadcast link resetting because of an excessive number of
retransmissions. This is caused by a combination of two factors:
1) A 'NACK crunch", where loss of broadcast packets is discovered
and NACK'ed by several nodes simultaneously, leading to multiple
redundant broadcast retransmissions.
2) The fact that the NACKS as such also are sent as broadcast, leading
to excessive load and packet loss on the transmitting switch/bridge.
This commit deals with the latter problem, by moving sending of
broadcast nacks from the dedicated BCAST_PROTOCOL/NACK message type
to regular unicast LINK_PROTOCOL/STATE messages. We allocate 10 unused
bits in word 8 of the said message for this purpose, and introduce a
new capability bit, TIPC_BCAST_STATE_NACK in order to keep the change
backwards compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, a received traffic packet can take a link
from state ESTABLISHING to ESTABLISHED, but the link can still not be
fully set up in one atomic operation. This means that even if the the
very first packet on the link is a traffic packet with sequence number
1 (one), it has to be dropped and retransmitted.
This can be avoided if we let the mentioned packet be preceded by a
LINK_PROTOCOL/STATE message, which takes up the endpoint before the
arrival of the traffic.
We add this small feature in this commit.
This is a fully compatible change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have kept a pre-allocated protocol message header
aggregated into struct tipc_link. Apart from adding unnecessary
footprint to the link instances, this requires extra code both to
initialize and re-initialize it.
We now remove this sub-optimization. This change also makes it
possible to clean up the function tipc_build_proto_msg() and remove
a couple of small functions that were accessing the mentioned header.
In particular, we can replace all occurrences of the local function
call link_own_addr(link) with the generic tipc_own_addr(net).
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing certain link attributes (link tolerance and link priority)
from the TIPC management tool is supposed to automatically take
effect at both endpoints of the affected link.
Currently the media address is not instantiated for the link and is
used uninstantiated when crafting protocol messages designated for the
peer endpoint. This means that changing a link property currently
results in the property being changed on the local machine but the
protocol message designated for the peer gets lost. Resulting in
property discrepancy between the endpoints.
In this patch we resolve this by using the media address from the
link entry and using the bearer transmit function to send it. Hence,
we can now eliminate the redundant function tipc_link_prot_xmit() and
the redundant field tipc_link::media_addr.
Fixes: 2af5ae372a (tipc: clean up unused code and structures)
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reported-by: Jason Hu <huzhijiang@gmail.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of variables with Hungarian notation (l_ptr, n_ptr etc.)
has been significantly reduced over the last couple of years.
We now root out the last traces of this practice.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the definition of struct tipc_link from link.h to link.c in
order to minimize its exposure to the rest of the code.
When needed, we define new functions to make it possible for external
entities to access and set data in the link.
Apart from the above, there are no functional changes.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our effort to have less code and include dependencies between
entities such as node, link and bearer, we try to narrow down
the exposed interface towards the node as much as possible.
In this commit, we move the definition of struct tipc_node, along
with many of its associated function declarations, from node.h to
node.c. We also move some function definitions from link.c and
name_distr.c to node.c, since they access fields in struct tipc_node
that should not be externally visible. The moved functions are renamed
according to new location, and made static whenever possible.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes in this series, we can now remove some
unused code and structures, both in the broadcast, link aggregation
and link code.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent commit series, we have established a one-way dependency
between the link aggregation (struct tipc_node) instances and their
pertaining tipc_link instances. This has enabled quite significant code
and structure simplifications.
In this commit, we eliminate the field 'owner', which points to an
instance of struct tipc_node, from struct tipc_link, and replace it with
a pointer to struct net, which is the only external reference now needed
by a link instance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have only been supporting a fix MTU size of 1500 bytes
for all broadcast media, irrespective of their actual capability.
We now make the broadcast MTU adaptable to the carrying media, i.e.,
we use the smallest MTU supported by any of the interfaces attached
to TIPC.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code path for receiving broadcast packets is currently distinct
from the unicast path. This leads to unnecessary code and data
duplication, something that can be avoided with some effort.
We now introduce separate per-peer tipc_link instances for handling
broadcast packet reception. Each receive link keeps a pointer to the
common, single, broadcast link instance, and can hence handle release
and retransmission of send buffers as if they belonged to the own
instance.
Furthermore, we let each unicast link instance keep a reference to both
the pertaining broadcast receive link, and to the common send link.
This makes it possible for the unicast links to easily access data for
broadcast link synchronization, as well as for carrying acknowledges for
received broadcast packets.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have tried to support both the newer, dedicated broadcast
synchronization mechanism along with the older, less safe, RESET_MSG/
ACTIVATE_MSG based one. The latter method has turned out to be a hazard
in a highly dynamic cluster, so we find it safer to disable it completely
when we find that the former mechanism is supported by the peer node.
For this purpose, we now introduce a new capabability bit,
TIPC_BCAST_SYNCH, to inform any peer nodes that dedicated broadcast
syncronization is supported by the present node. The new bit is conveyed
between peers in the 'capabilities' field of neighbor discovery messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit simplifies the broadcast link transmission function, by
leveraging previous changes to the link transmission function and the
broadcast transmission link life cycle.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realizing that unicast is just a special case of broadcast, we also see
that we can go in the other direction, i.e., that modest changes to the
current unicast link can make it generic enough to support broadcast.
The following changes are introduced here:
- A new counter ("ackers") in struct tipc_link, to indicate how many
peers need to ack a packet before it can be released.
- A corresponding counter in the skb user area, to keep track of how
many peers a are left to ack before a buffer can be released.
- A new counter ("acked"), to keep persistent track of how far a peer
has acked at the moment, i.e., where in the transmission queue to
start updating buffers when the next ack arrives. This is to avoid
double acknowledgements from a peer, with inadvertent relase of
packets as a result.
- A more generic tipc_link_retrans() function, where retransmit starts
from a given sequence number, instead of the first packet in the
transmision queue. This is to minimize the number of retransmitted
packets on the broadcast media.
When the new functionality is taken into use in the next commits,
we expect it to have minimal effect on unicast mode performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broadcast link instance (struct tipc_link) used for sending is
currently aggregated into struct tipc_bclink. This means that we cannot
use the regular tipc_link_create() function for initiating the link, but
do instead have to initiate numerous fields directly from the
bcast_init() function.
We want to reduce dependencies between the broadcast functionality
and the inner workings of tipc_link. In this commit, we introduce
a new function tipc_bclink_create() to link.c, and allocate the
instance of the link separately using this function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In reality, the link implementation is already independent from
struct tipc_bearer, in that it doesn't store any reference to it.
However, we still pass on a pointer to a bearer instance in the
function tipc_link_create(), just to have it extract some
initialization information from it.
I later commits, we need to create instances of tipc_link without
having any associated struct tipc_bearer. To facilitate this, we
want to extract the initialization data already in the creator
function in node.c, before calling tipc_link_create(), and pass
this info on as individual parameters in the call.
This commit introduces this change.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change made in the previous commit revealed a small flaw in the way
the node FSM is updated. When the function tipc_node_link_down() is
called for the last link to a node, we should check whether this was
caused by a local reset or by a received RESET message from the peer.
In the latter case, we can directly issue a PEER_LOST_CONTACT_EVT to
the node FSM, so that it is ready to re-establish contact. If this is
not done, the peer node will sometimes have to go through a second
establish cycle before the link becomes stable.
We fix this in this commit by conditionally issuing the mentioned
event in the function tipc_node_link_down(). We also move LINK_RESET
FSM even away from the link_reset() function and into the caller
function, partially because it is easier to follow the code when state
changes are gathered at a limited number of locations, partially
because there will be cases in future commits where we don't want the
link to go RESET mode when link_reset() is called.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is taken down because of a node local event, such as
disabling of a bearer or an interface, we currently leave it to the
peer node to discover the broken communication. The default time for
such failure discovery is 1.5-2 seconds.
If we instead allow the terminating link endpoint to send out a RESET
message at the moment it is reset, we can achieve the impression that
both endpoints are going down instantly. Since this is a very common
scenario, we find it worthwhile to make this small modification.
Apart from letting the link produce the said message, we also have to
ensure that the interface is able to transmit it before TIPC is
detached. We do this by performing the disabling of a bearer in three
steps:
1) Disable reception of TIPC packets from the interface in question.
2) Take down the links, while allowing them so send out a RESET message.
3) Disable transmission of TIPC packets on the interface.
Apart from this, we now have to react on the NETDEV_GOING_DOWN event,
instead of as currently the NEDEV_DOWN event, to ensure that such
transmission is possible during the teardown phase.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link establishing, just like link teardown, is a non-atomic action, in
the sense that discovering that conditions are right to establish a link,
and the actual adding of the link to one of the node's send slots is done
in two different lock contexts. The link FSM is designed to help bridging
the gap between the two contexts in a safe manner.
We have now discovered a weakness in the implementaton of this FSM.
Because we directly let the link go from state LINK_ESTABLISHING to
state LINK_ESTABLISHED already in the first lock context, we are unable
to distinguish between a fully established link, i.e., a link that has
been added to its slot, and a link that has not yet reached the second
lock context. It may hence happen that a manual intervention, e.g., when
disabling an interface, causes the function tipc_node_link_down() to try
removing the link from the node slots, decrementing its active link
counter etc, although the link was never added there in the first place.
We solve this by delaying the actual state change until we reach the
second lock context, inside the function tipc_node_link_up(). This
makes it possible for potentail callers of __tipc_node_link_down() to
know if they should proceed or not, and the problem is solved.
Unforunately, the situation described above also has a second problem.
Since there by necessity is a tipc_node_link_up() call pending once
the node lock has been released, we must defuse that call by setting
the link back from LINK_ESTABLISHING to LINK_RESET state. This forces
us to make a slight modification to the link FSM, which will now look
as follows.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | +----------------+ | |
| RESET_EVT| |RESET_EVT | |
| | | | |
| | | |ESTABLISH_EVT |
| | | +-------------+ | |
| | | | RESET_EVT | | |
| | | | | | |
| V V V | | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence number of an incoming packet is currently only checked
for less than, equality to, or bigger than the next expected number,
meaning that the receive window in practice becomes one half sequence
number cycle, or U16_MAX/2. This does not make sense, and may not even
be safe if there are extreme delays in the network. Any packet sent by
the peer during the ongoing cycle must belong inside his current send
window, or should otherwise be dropped if possible.
Since a link endpoint cannot know its peer's current send window, it
has to base this sanity check on a worst-case assumption, i.e., that
the peer is using a maximum sized window of 8191 packets. Using this
assumption, we now add a check that the sequence number is not bigger
than next_expected + TIPC_MAX_LINK_WIN. We also re-order the checks
done, so that the receive window test is performed before the gap test.
This way, we are guaranteed that no packet with illegal sequence numbers
are ever added to the deferred queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have been handling link failover and synchronization
by using an additional link state variable, "exec_mode". This variable
is not independent of the link FSM state, something causing a risk of
inconsistencies, apart from the fact that it clutters the code.
The conditions are now in place to define a new link FSM that covers
all existing use cases, including failover and synchronization, and
eliminate the "exec_mode" field altogether. The FSM must also support
non-atomic resetting of links, which will be introduced later.
The new link FSM is shown below, with 7 states and 8 events.
Only events leading to state change are shown as edges.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | | | |
| | +--------------+ | |
| RESET_EVT| |RESET_EVT |ESTABLISH_EVT |
| | | | |
| | | | |
| V V | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
These changes are fully backwards compatible.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of the link FSM currently takes decisions about and
sends out link protocol messages. This is unnecessary, since such
actions are not the result of any link state change, and are even
decided based on non-FSM state information ("silent_intv_cnt").
We now move the sending of unicast link protocol messages to the
function tipc_link_timeout(), and the initial broadcast synchronization
message to tipc_node_link_up(). The latter is done because a link
instance should not need to know whether it is the first or second
link to a destination. Such information is now restricted to and
handled by the link aggregation layer in node.c
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failover and synchronization have until now been handled by the
links themselves, forcing them to have knowledge about and to access
parallel links in order to make the two algorithms work correctly.
In this commit, we move the control part of this functionality to the
link aggregation level in node.c, which is the right location for this.
As a result, the two algorithms become easier to follow, and the link
implementation becomes simpler.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.
This change serves as a preparation for the coming commits.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_activate() is redundant, since it mostly performs
settings that have already been done in a preceding tipc_link_reset().
There are three exceptions to this:
- The actual state change to TIPC_LINK_WORKING. This should anyway be done
in the FSM, and not in a separate function.
- Registration of the link with the bearer. This should be done by the
node, since we don't want the link to have any knowledge about its
specific bearer.
- Call to tipc_node_link_up() for user access registration. With the new
role distribution between link aggregation and link level this becomes
the wrong call order; tipc_node_link_up() should instead be called
directly as a result of a TIPC_LINK_UP event, hence by the node itself.
This commit implements those changes.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We convert packet/message reception according to the same principle
we have been using for message sending and timeout handling:
We move the function tipc_rcv() to node.c, hence handling the initial
packet reception at the link aggregation level. The function grabs
the node lock, selects the receiving link, and accesses it via a new
call tipc_link_rcv(). This function appends buffers to the input
queue for delivery upwards, but it may also append outgoing packets
to the xmit queue, just as we do during regular message sending. The
latter will happen when buffers are forwarded from the link backlog,
or when retransmission is requested.
Upon return of this function, and after having released the node lock,
tipc_rcv() delivers/tranmsits the contents of those queues, but it may
also perform actions such as link activation or reset, as indicated by
the return flags from the link.
This reduces the number of cpu cycles spent inside the node spinlock,
and reduces contention on that lock.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our effort to move control of the links to the link aggregation
layer, we move the perodic link supervision timer to struct tipc_node.
The new timer is shared between all links belonging to the node, thus
saving resources, while still kicking the FSM on both its pertaining
links at each expiration.
The current link timer and corresponding functions are removed.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a second, simpler, link timer function, tipc_link_timeout().
The new function makes use of the new FSM function introduced in the
previous commit, and just like it, takes a buffer queue as parameter.
It returns an event bit field and potentially a link protocol packet
to the caller.
The existing timer function, link_timeout(), is still needed for a
while, so we redesign it to become a wrapper around the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link FSM implementation is currently unnecessarily complex.
It sometimes checks for conditional state outside the FSM data
before deciding next state, and often performs actions directly
inside the FSM logics.
In this commit, we create a second, simpler FSM implementation,
that as far as possible acts only on states and events that it is
strictly defined for, and postpone any actions until it is finished
with its decisions. It also returns an event flag field and an a
buffer queue which may potentially contain a protocol message to
be sent by the caller.
Unfortunately, we cannot yet make the FSM "clean", in the sense
that its decisions are only based on FSM state and event, and that
state changes happen only here. That will have to wait until the
activate/reset logics has been cleaned up in a future commit.
We also rename the link states as follows:
WORKING_WORKING -> TIPC_LINK_WORKING
WORKING_UNKNOWN -> TIPC_LINK_PROBING
RESET_UNKNOWN -> TIPC_LINK_RESETTING
RESET_RESET -> TIPC_LINK_ESTABLISHING
The existing FSM function, link_state_event(), is still needed for
a while, so we redesign it to make use of the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status flag LINK_STOPPED is not needed any more, since the
mechanism for delayed deletion of links has been removed.
Likewise, LINK_STARTED and LINK_START_EVT are unnecessary,
because we can just as well start the link timer directly from
inside tipc_link_create().
We eliminate these flags in this commit.
Instead of the above flags, we now introduce three new link modes,
TIPC_LINK_OPEN, TIPC_LINK_BLOCKED and TIPC_LINK_TUNNEL. The values
indicate whether, and in the case of TIPC_LINK_TUNNEL, which, messages
the link is allowed to receive in this state. TIPC_LINK_BLOCKED also
blocks timer-driven protocol messages to be sent out, and any change
to the link FSM. Since the modes are mutually exclusive, we convert
them to state values, and rename the 'flags' field in struct tipc_link
to 'exec_mode'.
Finally, we move the #defines for link FSM states and events from link.h
into enums inside the file link.c, which is the real usage scope of
these definitions.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the link input queue and the name distributor receive
queues are fields aggregated in struct tipc_link. This is a hazard,
because a link might be deleted while a receiving socket still keeps
reference to one of the queues.
This commit fixes this bug. However, rather than adding yet another
reference counter to the critical data path, we move the two queues
to safe ground inside struct tipc_node, which is already protected, and
let the link code only handle references to the queues. This is also
in line with planned later changes in this area.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1f66d161ab
("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.
Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.
We fix this bug with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We change the sequence number checkpointing that is performed
by the timer in order to discover if the peer is active. Currently,
we store a checkpoint of the next expected sequence number "rcv_nxt"
at each timer expiration, and compare it to the current expected
number at next timeout expiration. Instead, we now use the already
existing field "silent_intv_cnt" for this task. We step the counter
at each timeout expiration, and zero it at each valid received packet.
If no valid packet has been received from the peer after "abort_limit"
number of silent timer intervals, the link is declared faulty and reset.
We also remove the multiple instances of timer activation from inside
the FSM function "link_state_event()", and now do it at only one place;
at the end of the timer function itself.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename some fields in struct tipc_link, in order to give them more
descriptive names:
next_in_no -> rcv_nxt
next_out_no-> snd_nxt
fsm_msg_cnt-> silent_intv_cnt
cont_intv -> keepalive_intv
last_retransmitted -> last_retransm
There are no functional changes in this commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the sequence number in the TIPC protocol is 16 bits, we have
until now stored it internally as an unsigned 32 bits integer.
We got around this by always doing explicit modulo-65535 operations
whenever we need to access a sequence number.
We now make the incoming and outgoing sequence numbers to unsigned
16-bit integers, and remove the modulo operations where applicable.
We also move the arithmetic inline functions for 16 bit integers
to core.h, and the function buf_seqno() to msg.h, so they can easily
be accessed from anywhere in the code.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 4b475e3f2f8e4e241de101c8240f1d74d0470494
("tipc: eliminate delayed link deletion at link failover") the extra
boolean parameter "shutting_down" is not any longer needed for the
functions bearer_disable() and tipc_link_delete_list().
Furhermore, the function tipc_link_reset_links(), called from
bearer_reset() is now unnecessary. We can just as well delete
all the links, as we do in bearer_disable(), and start over with
creating new links.
This commit introduces those changes.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is being established, the two endpoints advertise their
respective interface MTU in the transmitted RESET and ACTIVATE messages.
If there is any difference, the lower of the two MTUs will be selected
for use by both endpoints.
However, as a remnant of earlier attempts to introduce TIPC level
routing. there also exists an MTU discovery mechanism. If an intermediate
node has a lower MTU than the two endpoints, they will discover this
through a bisectional approach, and finally adopt this MTU for common use.
Since there is no TIPC level routing, and probably never will be,
this mechanism doesn't make any sense, and only serves to make the
link level protocol unecessarily complex.
In this commit, we eliminate the MTU discovery algorithm,and fall back
to the simple MTU advertising approach. This change is fully backwards
compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled manually, all its links have to be reset
and deleted. However, if there is a remaining, parallel link ready
to take over a deleted link's traffic, we currently delay the delete
of the removed link until the failover procedure is finished. This
is because the remaining link needs to access state from the reset
link, such as the last received packet number, and any partially
reassembled buffer, in order to perform a successful failover.
In this commit, we do instead move the state data over to the new
link, so that it can fulfill the procedure autonomously, without
accessing any data on the old link. This means that we can now
proceed and delete all pertaining links immediately when a bearer
is disabled. This saves us from some unnecessary complexity in such
situations.
We also choose to change the confusing definitions CHANGEOVER_PROTOCOL,
ORIGINAL_MSG and DUPLICATE_MSG to the more descriptive TUNNEL_PROTOCOL,
FAILOVER_MSG and SYNCH_MSG respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite recent improvements, the establishment of dual parallel
links still has a small glitch where messages can bypass each
other. When the second link in a dual-link configuration is
established, part of the first link's traffic will be steered over
to the new link. Although we do have a mechanism to ensure that
packets sent before and after the establishment of the new link
arrive in sequence to the destination node, this is not enough.
The arriving messages will still be delivered upwards in different
threads, something entailing a risk of message disordering during
the transition phase.
To fix this, we introduce a synchronization mechanism between the
two parallel links, so that traffic arriving on the new link cannot
be added to its input queue until we are guaranteed that all
pre-establishment messages have been delivered on the old, parallel
link.
This problem seems to always have been around, but its occurrence is
so rare that it has not been noticed until recent intensive testing.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only use a single counter; the length of the backlog
queue, to determine whether a message should be accepted to the queue
or not. Each time a message is being sent, the queue length is compared
to a threshold value for the message's importance priority. If the queue
length is beyond this threshold, the message is rejected. This algorithm
implies a risk of starvation of low importance senders during very high
load, because it may take a long time before the backlog queue has
decreased enough to accept a lower level message.
We now eliminate this risk by introducing a counter for each importance
priority. When a message is sent, we check only the queue level for that
particular message's priority. If that is ok, the message can be added
to the backlog, irrespective of the queue level for other priorities.
This way, each level is guaranteed a certain portion of the total
bandwidth, and any risk of starvation is eliminated.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien