TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now no longer have any special code in
iwl_mvm_pass_packet_to_mac80211(), so don't
need to pass NO_PSDU packets through it.
Stop doing so and clean up the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.
Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor dram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WOWLAN images in unified firmwares should not be used, so don't require
them to support wowlan. This will allow to reduce the firmware's file
size.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor sram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is no way to debug RX/TX paths using prints
without harming tpt. Add prints to debug RX allocation path.
We can still get 1.9 gbps with those on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use IWL_DL_FW instead. This will free a bit for more
needed prints in newer devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 868a1e863f ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REGULATORY_WIPHY_SELF_MANAGED as set here breaks NL80211_CMD_GET_REG,
because it expects the wiphy to do regulatory management. Since
virt_wifi does not do regulatory management, this triggers a WARN_ON in
NL80211_CMD_GET_REG and fails the netlink command.
Removing REGULATORY_WIPHY_SELF_MANAGED fixes the problem and the virtual
wireless network continues to work.
Signed-off-by: Cody Schuffelen <schuffelen@google.com>
Acked-by: Alistair Strachan <astrachan@google.com>
Acked-by: Greg Hartman <ghartman@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a block of code that is indented at the wrong level. Fix this
with extra tabbing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of OWE, STA should be able to pass DH IEs from AP assoc
responses to wpa_s for processing. For this purpose DH IEs are
received from firmware in BSS_JOIN events and passed to wireless
core and then to wpa_s as additional optional rsp_ies parameter
for cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During wowlan regression tests, sometimes radio is not waking up for wowlan
packet in coex mode. This is because of power save is enabled by default
in case of coex mode greater than one. Hence, disable power save in coex
mode to avoid radio loss.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are redownloading the firmware after S4 restore and observed in
stress test that mac80211 sometimes gives power save request after
resume which causes the firmware in bad state. mac_ops_resumed flag
is added to skip that request until initialisation is done and Keeping
power save state is NONE.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At SDIO restore ieee80211_restart_hw() is getting called to restart all
MAC operations. This step is not required.
Returning 1 from mac80211_resume() will serve this purpose.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As we missed to detach HCI, while entering power off or hibernation,
an extra hci interface gets created whenever system is woken up, to
avoid this we added hci_detach() in rsi_disconnect(), rsi_freeze(),
and rsi_shutdown() functions which are invoked for these tests.
This patch fixes the issue
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a wowlan magic-packet has received to wake up the device, currently
driver is not taking care of what kind of packet has received. This patch
will add debug support for wakeup reason in driver.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/base.c: In function 'rtl_c2h_content_parsing':
drivers/net/wireless/realtek/rtlwifi/base.c:2313:13: warning:
variable 'cmd_seq' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BT coex event is not an error condition. Don't print an error
message in this case. The same even in sta_event.c prints a
message using the debug level already.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far there were two monitor frame formats:
1) 802.11 frames (with frame (sub)type & all addresses)
2) 802.11 frames with the radiotap header
Testing the latest FullMAC firmwares for 4366b1/4366c0 resulted in
discovering a new format being used. It seems (almost?) identical to the
one known from ucode used in SoftMAC devices which is most likely the
same codebase anyway.
While new firmwares will /announce/ radiotap header support using the
"rtap" fw capability string it seems no string was added for the new
ucode header format.
All above means that:
1) We need new format support when dealing with a received frame
2) A new feature bit & mapping quirks have to be added manually
As for now only an empty radiotap is being created. Adding support for
extracting some info (band, channel, signal, etc.) is planned for the
future.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spelling mistakes in brcmfmac: "lenght" -> "length".
The typos are also in the special comment blocks which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new macro uses wiphy_err() which:
1) Should be the best choice with wiphy already created
2) Uses dev_err() which allows identifying error-affected device
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables dev_err() usage (instead of pr_err()) in the __brcmf_err().
It makes error messages more meaningful and is important for debugging
errors/bugs on systems with multiple brcmfmac supported devices.
All bus files should follow & get updated similarly (soon).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far __brcmf_err() was using pr_err() which didn't allow identifying
device that was affected by an error. It's crucial for systems with more
than 1 device supported by brcmfmac (a common case for home routers).
This change allows passing struct brcmf_bus to the __brcmf_err(). That
struct has been agreed to be the most common one. It allows accessing
struct device easily & using dev_err() printing helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to test cfg80211 support for Multi-BSSID scan result
parsing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices like the Linksys EA6350v3, whose
country codes are not present in the original list. Without this patch,
all devices whose manufacturer programmed any of these code in their
EEPROM will not work.
The values for CTRY_UNITED_STATES2 and CTRY_UNITED_STATES3 were taken
from a post by Sven Eckelmann <sven.eckelmann@openmesh.com>:
<http://lists.infradead.org/pipermail/ath10k/2017-August/010014.html>
Signed-off-by: Oever Gonzalez <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;
-----BEGIN PGP SIGNATURE-----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=ckmd
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the age information for cfg80211 scan results more accurate
and fixes issues with wpa_supplicant dropping "old" scan results (e.g.,
"wlan0: Own scan request started a scan in 0.000456 seconds") that
looked like would have been received before a scan started due to the
inaccuracy of the default timing mechanism for calculating the BSS entry
age. This makes hwsim test cases significantly more robust to run.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of small, but importnat, fixes for 5.0.
iwlwifi
* fix a build regression introduced in 5.0-rc1
wlcore
* fix a firmware regression from v4.18-rc1
mt76x0
* fix for configuring tx power from user space
ath10k
* fix wcn3990 regression from v4.20-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWDsEAAoJEG4XJFUm622bSGsIAKevgvjWQkE7ITGfVuVNxRr9
B1pLgpOrQpVJtInbIS/sGpRKlcGn+3rE47KWzsl/1osGroQGcj5GV+hfGsvGkLwD
rzbYnAWA4VKP9yD/RDCho9v8kjAQYdfIArE7zpm14De0oXJHEn3C94Hxd90hn6CX
BhX4iZONcpIaAnggLj5aSIOo8+UFoE9BlGLFN0uNGQT2V0X/GjvZSfTAGsaof09Q
vSij06GNAoPF4g4ekJA0sJk0T3hJ8NNklrArKii7SE841j8Y1UaDHtHd/X5eUyLa
tB2pDvQgoCO6O5stZWtq1fr/qPBFthyE1TiMla5WgW+8l4QYaF14smNxkW5Kamg=
=5tr0
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.0
First set of small, but importnat, fixes for 5.0.
iwlwifi
* fix a build regression introduced in 5.0-rc1
wlcore
* fix a firmware regression from v4.18-rc1
mt76x0
* fix for configuring tx power from user space
ath10k
* fix wcn3990 regression from v4.20-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...) In this case,
if snprintf would have written more characters than what the buffer
size (SIZE) is, then size will end up larger than SIZE. In later uses
of snprintf, SIZE - size will result in a negative number, leading to
problems. Note that size might already be too large by using size =
snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to
user space, then it will potentially allow for a buffer overflow and
information disclosure when size is greater than SIZE. When the size is
used to index the buffer directly, we can have memory corruption. This
also means when size = snprintf... is used, it may also cause problems
since size may become large. Copying to userspace is mitigated by the
HARDENED_USERCOPY kernel configuration.
The solution to these issues is to use scnprintf which returns the number
of characters actually written to the buffer, so the size variable will
never exceed SIZE.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's a small hardware bug in 22260 devices which thus require a
few more delays during initialization. Implement this workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have >=10 (logical) CPUs, our command size exceeds the
internal buffer size and the command fails; fix that by using
IWL_HCMD_DFL_NOCOPY for the command that's allocated anyway.
While at it, also fix the leak of cmd, and use struct_size()
to calculate its size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 8edbfaa198 ("iwlwifi: mvm: configure multi RX queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Both iwl_trans_fw_error and iwl_force_nmi initiate async recovery flow.
Calling them both is redundant and causing a race.
Solve this by removing the call to iwl_trans_fw_error.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: cfadc3ffcc ("iwlwifi: pcie: stop the firmware when we restart it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement device internal memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement csr memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a skeleton to unite all memory dumps in ini mode.
Implement prph dump with the new skeleton.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New fields were added to struct iwl_fw_ini_region_cfg.
add those field and apply the changes the result from this change
offset field is used to differentiate between the different LMACs
and any memory access to the region addresses should be
base_addr + offset.
A fifo struct is to hold the meta data needed for fifo regions
Also move range_data_size and num_of_ranges into a struct under the
union to be aligned to the struct in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The hash mask is a bitmap, so we should use BIT() on
the enum values.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 43413a975d ("iwlwifi: mvm: support rss queues configuration command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update iwl_beacon_filter_cmd to support
BEACON_FILTER_CONFIG_API_S_VER_4.
Currently driver configs them to be zero
(i.e. disable them, so no change is applied).
Signed-off-by: Avigail Grinstein <avigail.grinstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Hiding the HE radiotap data for further processing of the SKB just
caused another bug when adding the L-SIG data. Simply stop doing
this and adjust the skb->data pointer accordingly when we need to
get the 802.11 header.
While at it, also verify and fix the data alignment, we need to add
2 bytes padding with the vendor data to ensure the whole length of
all radiotap headers is a multiple of 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6721039d5b ("iwlwifi: mvm: add L-SIG length to radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Depending on exactly what happens in the FW, an invalid host-command
could result in either assert 0x38 or 0x39. Add 0x39 to the assert-name
table.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Even if they're static const, there's no need to duplicate
the structs every time they're included and used. Move them
to an appropriate C file instead.
Also remove useless parentheses along the way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expose the trigger-based PPDU SIG-A bandwidth to radiotap in
the newly defined bits thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows in that can cause redundant allocation.
In case the driver reaches the maximum amount of blocks allowed, it
allocates the buffer and only then checks if it reached the maximum
amount of blocks and return without freeing the buffer,
causing a memory leak.
Solve this by moving the check of the amount of buffers being used
before the allocation.
In case there was an assert, the apply points are being reused,
causing that for each assert, the driver allocates a new redundant
buffer.
Solve this by adding a new is_alloc field to indicate if the driver
already allocated memory for the requested buffer.
Also, split iwl_fw_dbg_buffer_allocation function into
iwl_fw_dbg_buffer_allocation and iwl_fw_dbg_buffer_apply
to increase the clearity of the flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: d47902f9f7 ("iwlwifi: dbg: add apply point logic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use %u instead of using %d which looks signed but then won't
get signed output if using an unsigned variable. It doesn't
matter much, but be consistent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have a station connecting HE, make sure that the
MAC ctxt is updated with indication of this before
setting the TLC rates via the TLC manager command.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of having the command appear as "UNKNOWN" in the
dmesg, add the name to it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sta_alloc_queue_tvqm(), we know that we have a
station, so no need to check it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Typically, when not in HE mode, we will not perform well
with AMSDUs bigger than 8K.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we started to send the WEP keys to the firmware so
that we could use hardware Tx encryption also on newer
devices that require the keys to be installed in the firmware
for encryption (as opposed to older devices that can get
the key in the Tx command for each Tx).
When we implemented that, we forgot to remove the key when
we remove a station leading to a situation where a station
that connects and disconnects a lot of times exhausts the
key database inside the firmware.
A fix was made for that, but we always removed the same
key: mvmvif->ap_wep_key which means that we removed the
same key entry in the firmware. This can make sense since
in WEP, the key is the same for all the stations, but the
internal implementation of iwl_mvm_set_sta_key and
iwl_mvm_remove_sta_key assumes that each station uses a
different key in the firmware's key database.
So now we got to the situation where we have a single
ieee80211_key_conf instance that means, a single
ieee80211_key_conf.hw_key_idx index for several stations
and hence for several keys.
ieee80211_key_conf.hw_key_idx is set to 0 when the first
station associates, and then it is overwritten to 1 when
the second station associates which is a buggy of course.
This led to the following message upon the removal of the
second station:
iwlwifi 0000:00:03.0: offset 1 not used in fw key table.
WARNING: CPU: 2 PID: 27883 at net/mac80211/sta_info.c:1122 __sta_info_destroy_part2+0x16b/0x180 [mac80211]
RIP: 0010:__sta_info_destroy_part2+0x16b/0x180 [mac80211]
Call Trace:
__sta_info_destroy+0x2a/0x40 [mac80211]
sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
ieee80211_del_station+0x1d/0x30 [mac80211]
nl80211_del_station+0xe0/0x1f0 [cfg80211]
Fix this by copying the ieee80211_key_conf structure for
each and every station. This is the easiest way to properly
remove the keys with the right index. Another solution
would have been to allow several stations to use the same
key offset in the firmware. That would require to change
the way we track keys in iwlmvm and not really worth it.
Also, maintain correctly fw_key_table when we add a key
for the multicast station.
Remove the key when we remove the multicast station.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 337bfc9881 ("iwlwifi: mvm: set wep key for all stations in soft ap mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some switch-cases were missing a fall through comment, so the compiler
may warn. Fix that by adding the comments where needed. In other
cases there was more text in the comment, which the compiler doesn't
recognize, so either remove the extra text or move it to a separate
comment line as appropriate.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some case statements were missing a comment about falling through or
had more text than the compiler can recognize. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the documentation of the structs with the latest version in
the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several dumping flows in the driver in case of a fail
prior to operational.
In some cases we get 2 dumps while in others we get none.
Fix this by uniting the different flows.
Add a different dump type to driver triggered dumps in case we want
a dump but did not got assert, and make all dumping go through
iwl_fw_dbg_collect_desc to avoid multiple dumps.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is changing the format of the beacon
notification to remove the dependency on the Tx response
format.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver should support 64 region ids. Update
IWL_FW_INI_MAX_REGION_ID accordingly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the triggers enum in the driver to the one in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two cases that can cause the alive flow to fail,
an assert or a timeout.
Currently we mask any incoming asserts when we wait for alive.
Solve this by differentiating between the two cases:
1. Let the regular error handling to handle a received assert
2. Do a dump collection in the case of a timeout
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f38efdb293 ("iwlwifi: add dump collection in case alive flow fails")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do channel switch, we used to schedule time events
ourselves. This was offloaded to FW. Support the new command
and flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Simplify some return conditions found by running a semantic patch
to detect unnecessary assignments to local variables.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.
Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.
since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.
Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409ba3 ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some of the region struct fields have misleading naming
change those fields to have an informative naming
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
change IWL_FW_INI_LOCATION_SRAM_INVALID into IWL_FW_INI_LOCATION_INVALID
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
update ini struct documentation to the structs being used in the FW
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
I also removed one header search path in:
drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile
I was able to compile without it.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute WARN_ON with WARN_ON_ONCE in mt7601u_rx_next_seg_len
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a goto statement that is missing a tab for indentation. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while inserting and removing sdio module multiple times, we are getting
sdhci warnings. This is because, improper assignment of ocr_avail value.
Fixed this by assigning proper value.
This patch is enhancement for commit 78e450719c ("rsi: Fix 'invalid
vdd' warning in mmc").
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a statement that is indented too deeply. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a statement that is incorrectly indented, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Apparently the rt2x61 firmware fails temporarily to decode
broadcast packets if the shared keys are not assigned
in the "correct" sequence. At the same time unicast
packets work fine, since they are encrypted with the
pairwise key.
At least with WPA2 CCMP mode the shared keys are
set in the following sequence: keyidx=1, 2, 1, 2.
After a while only keyidx 2 gets decrypted, and
keyidx 1 is ignored, probably because there is never
a keyidx 3.
Symptoms are arping -b works for 10 minutes, since
keyidx=2 is used for broadcast, and then it stops
working for 10 minutes, because keyidx=1 is used.
That failure mode repeats forever.
Note, the firmware does not even know which keyidx
corresponds to which hw_key_idx so the firmware is
trying to be smarter than the driver, which is bound
to fail.
As workaround the function rt61pci_config_shared_key
requests software decryption of the shared keys,
by returning EOPNOTSUPP. However, pairwise keys are
still handled by hardware which works just fine.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use existing variable with dereferenced cmd_id field.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove declarations for inexistent functions from bus.h header.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that valid BSS entry exists in wireless core record
even in the case of successful connect reported by firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not reject RETRY changes in driver. This decision
should belong to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host wireless stack uses u32 type for RTS/FRAG threshold values.
Switch to u32 in driver: pass u32 values to firmware and let
firmware properly adapt these values according to its
internal representation.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the current implementation INTx interrupt is deasserted after the
control path processing. However this may lead to missed interrupts
from the wireless card. For instance, this may happen as a result
of control path activity, when another interrupt arrives before
INTx is deasserted.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support of EBUSY error code for remote procedures over QLINK protocol.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for 8977 chipset to mwifiex with SDIO
interface. Register offsets and supported feature flags are
updated. Firmware image used will be mrvl/sd8977_uapsta.bin.
Signed-off-by: Hemantkumar Suthar <shemant@marvell.com>
Signed-off-by: Rakesh Parmar <rakeshp@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves the clearing of rtlpriv->link_info.num_rx_inperiod in
rtl_watchdog_wq_callback a few lines down.
This is necessary since it is still used in the "AP off" detection
code block. Moved clearing of rtlpriv->link_info.num_rx_inperiod
as well for consistency.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This re-introduces the function rtl8723e_dm_refresh_rate_adaptive_mask.
This function was present in a previous version of the code base,
it works just fine for me -- as long as it is not using stale data.
Unlike the original version of this function it avoids using
dm.undec_sm_pwdb when no beacon was received.
Fixed a style nit in rtl8723e_dm_init_rate_adaptive_mask.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When no beacon was received, the value in dm.undec_sm_pwdb is most
likely out of date and should not be used to adjust the input path.
Assume instead that the signal level is low.
Fix the state machine in rtl8723e_dm_cck_packet_detection_thresh
which did not clear pre_cck_fa_state when changing cur_cck_pd_state
from CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW to CCK_PD_STAGE_HIGHRSSI
and back again to CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW, the register
RCCK0_CCA not written to 0x83 on the second change.
Explicitly initialize pre_cck_fa_state/cur_cck_fa_state in
rtl_dm_diginit.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This appears to trigger a firmware bug and causes severe
problems with rtl8723ae PCI devices.
When the power save mode is activated for longer periods
of time the firmware stops to receive any packets.
This problem was exposed by commit 873ffe154a ("rtlwifi:
Fix logic error in enter/exit power-save mode").
Previously the power save mode was only active rarely and
only for a short time so that the problem was not noticeable.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sysfs_create_group() could fail. The fix checkes its return values
and issue error messages if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report correct eeprom per channel power value.
Fix chan_vs_power map in mt76x0_get_power_info routine
Fixes: f2a2e819d6 ("mt76x0: remove eeprom dependency from mt76x0_get_power_info")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A call to iwl_mvm_add_rtap_sniffer_config() was missing due to a merge
damage when I submitted the patch mentioned below. And this causes
the following compilation warning:
drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c:195:13: warning: 'iwl_mvm_add_rtap_sniffer_config' defined but not used [-Wunused-function]
static void iwl_mvm_add_rtap_sniffer_config(struct iwl_mvm *mvm,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by adding the if block that calls this function.
Fixes: 9bf13bee2d ("iwlwifi: mvm: include configured sniffer AID in radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A bunch of fixes for issues found with static analyzers;
* Relicense the pcie submodule to dual GPL/BSD;
* Reworked the TOF/CSI implementation;
* Work on new debugging infra continues;
* Some product name updates in the human-readable strings
* Some more cleanups for the device configuration refactoring;
* General bugfixes;
* Other cleanups and small fixes;
-----BEGIN PGP SIGNATURE-----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=7bNM
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-01-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of iwlwifi patches intended for v5.1
* A bunch of fixes for issues found with static analyzers;
* Relicense the pcie submodule to dual GPL/BSD;
* Reworked the TOF/CSI implementation;
* Work on new debugging infra continues;
* Some product name updates in the human-readable strings
* Some more cleanups for the device configuration refactoring;
* General bugfixes;
* Other cleanups and small fixes;
* fixes for mt76x0/mt76x2
* energy detect regulatory compliance fixes
* tx status handling fixes
* preparation for MT7603 support
* channel switch announcement support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlxHOf4ACgkQ130UHQKnbvUnmwCg1qdMIcAUT28xG2my8VxqelEP
BpMAn2uqBD+P+QBIgyXDN3GGF0P+UOWu
=exYK
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2019-01-22' of https://github.com/nbd168/wireless
first batch of mt76 patches for 5.1
* fixes for mt76x0/mt76x2
* energy detect regulatory compliance fixes
* tx status handling fixes
* preparation for MT7603 support
* channel switch announcement support
The monitor buffer register address is wrong.
Set the right address
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: c2d202017d ("iwlwifi: pcie: add firmware monitor capabilities")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver sets dump_mask value instead of BIT(value).
fix it by updating dump_mask correctly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver uses ignore_consec instead of dump_delay.
Fix it by using dump_delay as expected.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
in case of a user trigger while ini is enable we change
FW_DBG_TRIGGER_USER to IWL_FW_TRIGGER_ID_USER_TRIGGER in
iwl_fw_dbg_collect and then again we attempt to do so in
_iwl_fw_error_ini_dump which causes to abort the dump.
Fix it by removing the second check in _iwl_fw_error_ini_dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the same flags we use in the legacy buffer allocation.
Missing __GFP_NOWARN will cause an unwanted warning incase
we fail to allocate.
Missing __GFP_ZERO will give a buffer initially filled with
garbage which can make debug difficult in case our wrap count is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: d47902f9f7 ("iwlwifi: dbg: add apply point logic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When MU EDCA params change, resend the STA_HE_CTXT command
updating the MU EDCA params.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the regular flow, when we receive an assert, ieee80211_reconfig is
called which reconfig the driver using iwl_mvm_mac_start.
iwl_mvm_mac_start is clearing the restart bit and does dump collection.
Prior to setting the device up, ieee80211_reconfig does not call
iwl_mvm_mac_start since there is nothing to reconfig and we miss the
dump collection of the assert.
solve it by checking the restart bit before we stop the device
and trigger a dump collection in case it is set.
note that we don't need to do it in the fmac case since in fmac
assert flow in iwl_fmac_nic_error we call iwl_fw_dbg_collect_desc
so we can be sure that there will a dump collection in
iwl_fmac_stop_device.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to make more sense out of the captured radiotap data e.g.
when the configured AID changes, add the currently configured AID
to the radiotap data as a vendor extension field.
This is made race-free by updating the included value from inside
the RX path (using a notification wait) for the command response
from the firmware, which thus means it's serialized with frame RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reorder buffer is bypassed because the firmware won't have
any BA sessions, document this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
update the product name for the some of the cards from
the series of 9260 and 9560
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We introduce a new state for latency, force mode, in force mode
you can enable always to be in low latency or always to be in non
low latency.
This is required for test mode in max TpT test.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We maintain a timer for each Tx queue to detect stalls and
be able to recover / debug.
When we work in AP mode, we can freeze the Tx queue timer if
a station goes to sleep, because we don't want to warn about
stalls that are caused by faulty clients that don't wake up
on time.
This mechanism was applied to the queues of the clients, but
the management queue was omitted. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change iwl_fw_channel_info structure so it can have channel number
greater than 255. This is needed for 6 GHz channel numbers.
Change all relevant structs and member accesses accordingly.
The new API is indicated by a TLV capability bit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.
Currently only a debugfs API is provided as the API is still
under discussion.
For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the location/time-of-flight/FTM APIs that we'll use in
follow-up patches to implement FTM responder and initiator.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some buggy APs stop sending beacons, but continue to ack our null data
packets or even run some traffic. It's better not to stick connected to
such an AP forever, so disconnect after some larger beacon loss
threshold is crossed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
That's what we pass, and we don't want/need any negative values.
Found by sparse/smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we're in the else branch of checking "tt->state == IWL_TI_CT_KILL"
so there's no point in checking "tt->state != IWL_TI_CT_KILL" again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX path lock was introduced in order to prevent out of order
invocations of TX.
This can happen in the following flow:
TX path invoked from net dev
Packet dequeued
TX path invoked from RX path
Packet dequeued
Packet TXed
Packet TXed
However, we don't really need a lock. If TX path is already
invoked from some location, other paths can simply abort their
execution, instead of waiting to the first path to finish, and
then discover queue is (likely) empty or stopped.
Replace the lock with an atomic variable to track TX ownership.
This simplifies the locking dependencies between RX and TX paths,
and should improve performance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current code assigns the reference, and then goes to increment
it if the toggle bit has changed. That way, we get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 1 2 2 2
Fix that by assigning the post-toggle ID to get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 2 2 2 2
Reported-by: Danny Alexander <danny.alexander@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: fbe4112791 ("iwlwifi: mvm: update mpdu metadata API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently whenever we get firmware notification with mac id,
we iterate over all the interfaces to find the ID. This is a
bit cumbersome. Instead, adding an array of RCU pointers, like
we have for station IDs. This is not expensive space wise
since we have only up to 4 active MACs, and not complicated
code wise, since we have a clear point to init and de-init it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we use a dumping mask, checking if only monitor was requested
is redundant. Remove the unneeded code.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If WEP is used, no one removes the STA key upon STA
removal, leading to a situation where after 16
connect/disconnects - the AP could no longer decrypt
incoming data frames since iwl_mvm_set_fw_key_idx()
called from iwl_mvm_set_sta_key() during association
returns STA_KEY_IDX_INVALID, thus not setting the key
for that connecting STA.
Fix this by removing the key in the driver when the
STA is removed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Harden the fwrt->fw->img array access by making sure the cur_fw_img
value doesn't go out of bounds.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The out_cmd structure starts with a header, so there's no need to use
&out_cmd->hdr, out_cmd alone is enough. We use this when calculating
other addresses and klocwork gets confused with that because it thinks
we are trying to access hdr (as an array) beyond its size.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The function we pass to the wait alive notification procedure may may
not even get called if the timeout occurs before the function is
called. To prevent accessing unitialized data in alive_data, pre-set
it to zero in the declaration. Found by static analyzers.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These inlines just check the module parameters, so they don't
need a configuration parameter and can move to a better place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is supposed to be used as an inline function and is in a
header file, so make it inline.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes we want to debug issues related to the regulatory blob in
the NVM. To make that easier, add a debugfs entry to export it
together with the other nvm blobs we export.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clean up the LDBG config command to not be called "continuous
recording", and while at it actually remove the continuous
recording implementation completely since it was only used for
store & forward architectures.
This also fixes a bug at least in iwl_fw_dbg_buffer_allocation()
because what's now "__le32 type" (matching the firmware) used to
be "__le16 enable_recording", so the buffer allocation config
sub-struct would erroneously have started at the wrong offset.
In the other cases this didn't actually lead to a bug as other
bytes in pad[] were all zeroes, so accessing the 16-bit value as
a 32-bit value wouldn't make a difference (in little endian.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These files have a long history of code changes, but analysing
the remaining code leads to having only a few changes that are
not already owned by Intel, notably from
- Andy Lutomirski <luto@amacapital.net>
- Joonwoo Park <joonwpark81@gmail.com>
- Kirtika Ruchandani <kirtika@chromium.org>
- Rajat Jain <rajatja@google.com>
- Stanislaw Gruszka <sgruszka@redhat.com>
remaining in the code today.
Note that
- I myself was working for Intel and for any possibly code
that might be before my employment there give permission
- Wizery employees were working for Intel
More specifically, we identified the following commits that
(partially may) remain today:
25c03d8e8c Joonwoo Park <joonwpark81@gmail.com> ("iwlwifi: do not schedule tasklet when rcv unused irq")
f36d04abe6 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: use dma_alloc_coherent")
387f3381f7 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: fix dma mappings and skbs leak")
2624e96ce1 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: fix possible data overwrite in hcmd callback")
bfe4b80e9f Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: always check if got h/w access before write")
d536c32b45 Andy Lutomirski <luto@amacapital.net> ("iwlwifi: pcie: log when waking the NIC for hcmd submission fails")
a6d24fad00 Rajat Jain <rajatja@google.com> ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
fb12777ab5 Kirtika Ruchandani <kirtika@chromium.org> ("iwlwifi: Add more call-sites for pcie reg dumper")
3a73a30049 Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: cleanup/fix memory barriers")
aa5affbacb Stanislaw Gruszka <sgruszka@redhat.com> ("iwlwifi: dump stack when fail to gain access to the device")
Align the licenses with their permission to clean up and to
make it all identical.
CC: Joonwoo Park <joonwpark81@gmail.com>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Rajat Jain <rajatja@google.com>
CC: Kirtika Ruchandani <kirtika@chromium.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kirtika Ruchandani <kirtika@chromium.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Joonwoo Park <joonwpark81@gmail.com>
Acked-by: Rajat Jain <rajatja@google.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a general shortage of RX API bits, the firmware is going
to reuse this bit on non-CCK frames to mean something else. Use
it only on CCK frames to prepare for that change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With just %16, it means 16 characters padding, but we really
don't want to print "0x 1F4547B", but instead want to
have this filled with zeroes, so we need the 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there are bugs in this area, this data can
help with debugging.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Take the NSS value from 'rx_vec' rather than from 'rate_n_flags'.
The rate_n_flags has only 2 bits for the NSS giving a max of 4SS
(0 = 1SS etc.). Since there may be up to 8SS use the rx_vec which
has 3 bits for the NSS.
While at it, fix the rx_vec array to length of 2.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When setting the EOF bit in Rx flags (propagated
to radiotap) do not depend it on the PPDU type (SU/MU/TB)
since it doesn't.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code checks that we haven't exceeded the maximum number of
TBs by comparing to a define of gen1 instead of gen2, fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These are unused by both firmware and driver, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value in num_lmac can be bigger than mem_cfg->lmac array,
warn in case it's bigger.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 68025d5f9b ("iwlwifi: dbg: refactor dump code to improve readability")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value in txq_id can be out of array scope,
validate it before accessing the array.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Klocwork complains about copying from dev_cmd->hdr if
copying more than 4 bytes since it means part of the
copy is from the next field. This isn't a real bug,
but for not failing Klocwork next time - fix this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver assumes certain sizes and lengths aren't crossed in some
places. Make sure this indeed happens.
Found by Klocwork.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no point in having num_active_macs signed
since it should never be negative. Set it to be an
unsigned variable to ensure this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few commands refer to a struct that no longer exists
in the mentioned name. Our trace-cmd parsing scripts
rely on these mentioned names and can't find them,
resulting in these commands not being parsed nicely.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As this is not needed and might cause interoperability issues
during pairing with devices that would not reply to RTS frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a frame is transmitted without a station, need to set the rate
and flags in the Tx command, as the FW does not have any information as
to what rate and flags should be used for this frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a time event for a P2P Device interface is done, it is possible
that there is still a frame pending for transmission that should be
flushed.
Set the IWL_MVM_STATUS_NEED_FLUSH_P2P to indicate to the ROC worker
that P2P Device station queue need also to be flushed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a slightly better TCP performance with GSO.
Add it back, it can co-exist with the code that builds
AMSDUs in mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trivial fix to spelling mistake in IWL_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use kmemdup rather than duplicating its implementation in
iwl_parse_nvm_mcc_info().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We erroneously had some values for NGI in the table we give as an
example in rs_fill_rates_for_column(), when they should be SGI.
Change them so that they match what we say.
Reported-by: Rémy Grünblatt <remy@grunblatt.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting mac80211 building AMSDUs for us. Remove GSO
support from mvm - we don't need it anymore.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.
The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.
When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.
Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On any failure, including if we crash the firmware or get garbage
data, we currently ignore this and pretend the OTP was empty.
Clearly, this isn't typically the case.
In cases other than the firmware saying it can't read the requested
section, or the section having ended, make the access actually fail
and trickle the error up through the layers to fail init.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add prph dump addresses to support prph dump in 22000 HW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function was only used by 9000 A-step devices, which we don't
support anymore, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support 9000 A-step devices anymore, so we can remove support
for loading both the a0/a0 and a0/b0 FWs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new (CDB) statistics API is used by non-CDB devices
as well. Look at the right TLV flag to know which version
of the statistics notification to use.
To avoid confusion, remove the _cdb suffix from the
structure name.
While at it, remove a structure that was never used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 678d9b6ddd ("iwlwifi: mvm: update rx statistics cmd api")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the cfg struct names is mistakenly "iwl22000", when it should
be "iwl22560".
Chage-Id: If9fbfa4bceef81d028c90c98d47115fbe39da547
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Fixes: 2f7a386319 ("iwlwifi: rename the temporary name of A000 to the official 22000")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When configuring TLC DCM flag:
1. check the peer's RX DCM capabilities (since we TX)
2. do not set DCM_NSS_2 since we do not support it
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Fixes: 423584dd80 ("iwlwifi: rs-fw: support dcm")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices with PCI ID 0x2723, which is supposed to be 22260, are
actually not. So we need to differentiate them by checking the hw_rev
and change the cfg accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mac80211 will check both the HE Capability IE and the
Extended Capability IE, so set the TWT support bit when
mac80211 tells us to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to advertise support for TWT in the Extended
Capability IE. Since we don't want to set the bits for all
the interface types, define an interface specific
configuration.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the dump the number of lmacs, the error id of the umac
and the error id of lmac1, if supported.
In case the reason for the dump trigger is not an assert
the error id is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't populate the array prop on the stack but instead make it static.
Makes the object code smaller by 30 bytes:
Before:
text data bss dec hex filename
80138 15382 576 96096 17760 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
After:
text data bss dec hex filename
79948 15542 576 96066 17742 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During "wlan-up", we are programming the FW into the WiFi-chip. However,
re-programming the FW doesn't work, unless a power cycle of the WiFi-chip
is made in-between the programmings.
To conform to this requirement and to fix the regression in a simple way,
let's start by allowing that the SDIO card (WiFi-chip) may stay powered on
(runtime resumed) when wl12xx_sdio_power_off() returns. The intent with the
current code is to treat this scenario as an error, but unfortunate this
doesn't work as expected, so let's fix this.
The other part is to guarantee that a power cycle of the SDIO card has been
completed when wl12xx_sdio_power_on() returns, as to allow the FW
programming to succeed. However, relying solely on runtime PM to deal with
this isn't sufficient. For example, userspace may prevent runtime suspend
via sysfs for the device that represents the SDIO card, leading to that the
mmc core also keeps it powered on. For this reason, let's instead do a
brute force power cycle in wl12xx_sdio_power_on().
Fixes: 728a9dc61f ("wlcore: sdio: Fix flakey SDIO runtime PM handling")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case a tx queue wake call arrives after a client has transitioned to
powersave, make sure that the queue is not kept active until the client
has left powersave mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Take into account device rx stream in mt76x02_mac_process_rate
in order to not report wrong number of rx spatial stream to mac80211.
The issue has been reported on mt76x0 device which is 1x1:1 however
the hw sometimes reports rx nss equal to 2
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/virt_wifi.c: In function 'virt_wifi_net_device_stop':
drivers/net/wireless/virt_wifi.c:432:31: warning:
variable 'w_priv' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c7cdba31ed ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Under certain circumstances, radios created via netlink could
have n_limits be zero and no possible interface types, which
makes no sense. Reject this early to prevent a WARN_ON() in
cfg80211.
Fixes: 99e3a44bac ("mac80211_hwsim: allow setting iftype support")
Reported-by: syzbot+73fd8b0aa60c67fa4b60@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The generic EWMA code cannot deal with negative numbers, so convert signal
to a positive number before adding it
Fixes mt76x2 AGC tuning
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware does not deal with multiple WCID entries for the same station
properly. Set IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR to avoid those cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since IWLWIFI doesn't depend on MAC80211 anymore, it needs to depend
on CFG80211, because it uses a few symbols from it. Add the
dependency on CFG80211 accordingly.
Additionally, make IWLWIFI_LEDS depend on IWLMVM or IWLDVM, since it
doesn't need mac80211 but must be used for these.
Fixes: aca432f06b ("iwlwifi: make MVM and DVM depend on MAC80211")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mt76x02 led support in mt76x02-lib module in order to
add tpt led trigger to mt76x0e driver
Tested-by: LGA1150 <dqfext@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper name for __MT76x02_H macro in mt76x02.h
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Call mt76_dma_add_buf routine directly in mt76_dma_tx_queue_skb
and avoid indirect call if not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the const array 'data' on the stack but instead
make it static. Makes the object code smaller by 78 bytes:
Before:
text data bss dec hex filename
5438 1080 0 6518 1976 mediatek/mt76/mt76x2/usb_mcu.o
After:
text data bss dec hex filename
5296 1144 0 6440 1928 mediatek/mt76/mt76x2/usb_mcu.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Port mt76x02_check_tx_hang watchdog from vendor driver in order to
perform a device reset when tx mac/dma logic hangs. Tx mac/dma stuck
has been observed when the device is heavy loaded or in a noisy
environment. Moreover introduce wdt delayed work in order to run
tx_hang watchdog. For the moment run mt76x02_check_tx_hang watchdog
just on mt76x2 devices since the issue has not been observed on mt76x0
driver yet
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not set bw variable to zero for legacy rates since it is already
initialized to zero. Moreover set nss to 1 just for legacy rates
since nss will be properly set for VHT/HT rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update default value for MT_TX_LINK_CFG according to vendor driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_dfs_set_domain since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add static qualifier to mt76x2_init_hardware routine since it is
used just in pci_init.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure MT_VHT_HT_FBK_CFG1 values similar like vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On new mt76 chips, phy mode is configured by last 3 bits
of rate value. Hence OFDM bit is marked by 0x2000
instead of 0x4000.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.
Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for pcie code in commit 79d1c94c9c ("mt76: avoid
queue/status spinlocks while passing tx status to mac80211") make sure
that no tx related spinlocks are taken during the ieee80211_tx_status call
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_mac_work handler since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reconfigure properly MT_MAC_SYS_CTRL register after mac sw-reset
in mt76x02_check_mac_err routine
Fixes: 73556561ab ("mt76x0: use mt76x02_mac_work as stats handler")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove napi from mt76_dma_rx_fill routine signature since
it is a leftover of a previous implementation and it is no
longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
So far the code only validates the buffer size of the first skb.
Extend this check to cover additional fragments as well, in case the size
is corrupted during a DMA reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ath6kl_wmi_cmd_send could fail, so let's return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_of_init() function[0] was initially written on the assumption that
if someone had an explicit ath9k OF node that "there must be something
wrong, why would someone add an OF node if everything is fine"[1]
(Quoting Martin Blumenstingl <martin.blumenstingl@googlemail.com>)
"it turns out it's not that simple. with your requirements I'm now aware
of two use-cases where the current code in ath9k_of_init() doesn't work
without modifications"[1]
The "your requirements" Martin speaks of is the result of the fact that I
have a device (PowerCloud Systems CR5000) has some kind of default - not
unique mac address - set and requires to set the correct MAC address via
mac-address devicetree property, however:
"some cards come with a physical EEPROM chip [or OTP] so "qca,no-eeprom"
should not be set (your use-case). in this case AH_USE_EEPROM should be
set (which is the default when there is no OF node)"[1]
The other use case is:
the firmware on some PowerMac G5 seems to add a OF node for the ath9k
card automatically. depending on the EEPROM on the card AH_NO_EEP_SWAP
should be unset (which is the default when there is no OF node). see [3]
After this patch to ath9k_of_init() the new behavior will be:
if there's no OF node then everything is the same as before
if there's an empty OF node then ath9k will use the hardware EEPROM
(before ath9k would fail to initialize because no EEPROM data was
provided by userspace)
if there's an OF node with only a MAC address then ath9k will use
the MAC address and the hardware EEPROM (see the case above)
with "qca,no-eeprom" EEPROM data from userspace will be requested.
the behavior here will not change
[1]
Martin provides additional background on EEPROM swapping[1].
Thanks to Christian Lamparter <chunkeey@gmail.com> for all his help on
troubleshooting this issue and the basis for this patch.
[0]https://elixir.bootlin.com/linux/v4.20-rc7/source/drivers/net/wireless/ath/ath9k/init.c#L615
[1]https://github.com/openwrt/openwrt/pull/1645#issuecomment-448027058
[2]https://github.com/openwrt/openwrt/pull/1613
[3]https://patchwork.kernel.org/patch/10241731/
Fixes: 138b41253d ("ath9k: parse the device configuration from an OF node")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The linux-firmware brcmfmac firmware files contain an embedded table with
per country allowed channels and strength info.
For recent hardware these versions of the firmware are specially build for
linux-firmware, the firmware files directly available from Cypress rely on
a separate clm_blob file for this info.
For some unknown reason Cypress refuses to provide the standard firmware
files + clm_blob files it uses elsewhere for inclusion into linux-firmware,
instead relying on these special builds with the clm_blob info embedded.
This means that the linux-firmware firmware versions often lag behind,
but I digress.
The brcmfmac driver does support the separate clm_blob file and always
tries to load this. Currently we use request_firmware for this. This means
that on any standard install, using the standard combo of linux-kernel +
linux-firmware, we will get a warning:
"Direct firmware load for ... failed with error -2"
On top of this, brcmfmac itself prints: "no clm_blob available (err=-2),
device may have limited channels available".
This commit switches to firmware_request_nowarn, fixing almost any brcmfmac
device logging the warning (it leaves the brcmfmac info message in place).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a system warning message, warn_slowpath-fmt, during suspend
while using supplicant join AP and enable wowl feature by IW command.
It's caused by brcmf_pno_remove_request path can't find the reqid.
This fix will not go to remove pno request function if there is no
pno scan.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Lo-Hsiang Lo <double.lo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_register() may fail, so let's check its status and issue an error
message if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop LIST_HEAD where the variable it declares has never
been used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the missing unlock before return from function cw1200_hw_scan()
in the error handling case.
Fixes: 4f68ef64cd ("cw1200: Fix concurrency use-after-free bugs in cw1200_hw_scan()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Point of View TAB-P1006W-232 tablet contains quite generic names in
the sys_vendor and product_name DMI strings, without this patch brcmfmac
will try to load: brcmfmac43340-sdio.Insyde-BayTrail.txt as nvram file
which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file
name is used on the PoV TAB-P1006W-232 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently array element org[3] is being accessed, however the array is
only 3 elements in size, so this looks like an off-by-one out-of-bounds
error. Fix this by using org[2], which I believe was the original
intent.
This issue has existed in the driver back in the pre-git days, so no
idea when it was introduced.
Detected by CoverityScan, CID#711344 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1202:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4625:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4834:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3085:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4215:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAlwb7R8QHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpjiID/97oDjMhNT7rwpuMbHw855h62j1hEN/m+N3
FI0uxivYoYZLD+eJRnMcBwHlKjrCX8iJQAcv9ffI3ThtFW7dnZT3atUacaZVR/Dt
IrxdymdBP3qsmuaId5NYBug7rJ+AiqFJKjEvCcSPu5X397J4I3SEbzhfvYLJ/aZX
16o0HJlVVIrcbmq1IP4HwiIIOaKXvPaw04L4z4fpeynRSWG7EAi8NLSnhlR4Rxbb
BTiMkCTsjRCFdyO6da4fvNQKWmPGPa3bJkYy3qR99cvJCeIbQjRyCloQlWNJRRgi
3eJpCHVxqFmN0/+DNTJVQEEr4H8o0AVucrLVct1Jc4pessenkpoUniP8vELqwlng
Z2VHLkhTfCEmvFlk82grrYdNvGATRsrbswt/PlP4T7rBfr1IpDk8kXDWF59EL2dy
ly35Sk3wJGHBl8qa+vEPXOAnaWdqJXuVGpwB4ifOIatOls8mOxwfZjiRc7x05/fC
1O4rR2IfLwRqwoYHs0AJ+h6ohOSn1mkGezl2Tch1VSFcJUOHmuYvraTaUi6hblpA
SslaAoEhO39hRBL0HsvsMeqVWM9uzqvFkLDCfNPdiA81H1258CIbo4vF8z6czCIS
eeXnTJxVhPVbZgb3a1a93SPwM6KIDZFoIijyd+NqjpU94thlnhYD0QEcKJIKH7os
2p4aHs6ktw==
=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Shahar S Matityahu