During refactor in commit 9e478066ea ("mac80211: fix MU-MIMO
follow-MAC mode") a new struct 'action' was declared with packed
attribute as:
struct {
struct ieee80211_hdr_3addr hdr;
u8 category;
u8 action_code;
} __packed action;
But since struct 'ieee80211_hdr_3addr' is declared with an aligned
keyword as:
struct ieee80211_hdr {
__le16 frame_control;
__le16 duration_id;
u8 addr1[ETH_ALEN];
u8 addr2[ETH_ALEN];
u8 addr3[ETH_ALEN];
__le16 seq_ctrl;
u8 addr4[ETH_ALEN];
} __packed __aligned(2);
Solve the ambiguity of placing aligned structure in a packed one by
adding the aligned(2) attribute to struct 'action'.
This removes the following warning (W=1):
net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned]
Cc: Johannes Berg <johannes.berg@intel.com>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot reported an out-of-bounds read when passing certain
malformed messages into nl80211. The specific place where
this happened isn't interesting, the problem is that nested
policy parsing was referring to the wrong maximum attribute
and thus the policy wasn't long enough.
Fix this by referring to the correct attribute. Since this
is really not necessary, I'll come up with a separate patch
to just pass the policy instead of both, in the common case
we can infer the maxattr from the size of the policy array.
Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
max_rcvbuf_size is no longer used since commit "414574a0af36".
Signed-off-by: Zhaolong Zhang <zhangzl2013@126.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because bbr_target_cwnd() is really a general-purpose BBR helper for
computing some volume of inflight data as a function of the estimated
BDP, refactor it into following helper functions:
- bbr_bdp()
- bbr_quantization_budget()
- bbr_inflight()
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlxHFuoTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8eRAB/9Sp32xbjIVeyyEro8+vmlJ/HlSNgcC
txqmmh0ce4n1gglV3G5ll8mDYJsk5Qz+ur8wbud7CVxFmpeGqkAA7qoYeD8DawSp
/77dBG8yX/t8vxU5jGK9l5FomVcrqKSVbK20R6u0MLeZhF+VdJCu7cDElgIsKDqX
N76Df/mTnfdhReoM05CXEwzvEN8StHljm+oecyunxfw3XPtqDkO7QHEVYpk2zwVI
4U2aYu9L1gDbj5yGXNu8l/WwEL4ttyC7rqoW9we1hsDVtxRh1/o+Tond6/HPxIcN
voO/fm97ZKxpDL3cE0Jg6Grq9jUek7GT8oRRkAdWO4YaLr3f70kibQ3s
=d+ps
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.0-20190122' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-01-22
this is a pull request of 4 patches for net/master.
The first patch by is by Manfred Schlaegl and reverts a patch that caused wrong
warning messages in certain use cases. The next patch is by Oliver Hartkopp for
the bcm that adds sanity checks for the timer value before using it to detect
potential interger overflows. The last two patches are for the flexcan driver,
YueHaibing's patch fixes the the return value in the error path of the
flexcan_setup_stop_mode() function. The second patch is by Uwe Kleine-König and
fixes a NULL pointer deref on older flexcan cores in flexcan_chip_start().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set
flow sport from 'saddr'. However, transport->saddr is set only when
transport->dst exists in sctp_transport_route().
If sctp_transport_pmtu() is called without transport->saddr set, like
when transport->dst doesn't exists, the flow sport will be set to 0
from transport->saddr, which will cause a wrong route to be got.
Commit 6e91b578bf ("sctp: re-use sctp_transport_pmtu in
sctp_transport_route") made the issue be triggered more easily
since sctp_transport_pmtu() would be called in sctp_transport_route()
after that.
In gerneral, fl4->fl4_sport should always be set to
htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist
in sctp_v4/6_get_dst(), which is the case:
sctp_ootb_pkt_new() ->
sctp_transport_route()
For that, we can simply handle it by setting flow sport from saddr only
when it's 0 in sctp_v4/6_get_dst().
Fixes: 6e91b578bf ("sctp: re-use sctp_transport_pmtu in sctp_transport_route")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the paths:
sctp_sf_do_unexpected_init() ->
sctp_make_init_ack()
sctp_sf_do_dupcook_a/b()() ->
sctp_sf_do_5_1D_ce()
The new chunk 'retval' transport is set from the incoming chunk 'chunk'
transport. However, 'retval' transport belong to the new asoc, which
is a different one from 'chunk' transport's asoc.
It will cause that the 'retval' chunk gets set with a wrong transport.
Later when sending it and because of Commit b9fd683982 ("sctp: add
sctp_packet_singleton"), sctp_packet_singleton() will set some fields,
like vtag to 'retval' chunk from that wrong transport's asoc.
This patch is to fix it by setting 'retval' transport correctly which
belongs to the right asoc in sctp_make_init_ack() and
sctp_sf_do_5_1D_ce().
Fixes: b9fd683982 ("sctp: add sctp_packet_singleton")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to improve sctp stream adding events in 2 places:
1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM
and in stream allocation failure checks, as the adding has to
succeed after reconf_timer stops for the in stream adding
request retransmission.
3. In sctp_process_strreset_addstrm_in(), no event should be sent,
as no in or out stream is added here.
Fixes: 50a41591f1 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter")
Fixes: c5c4ebb3ab ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to improve sctp stream reset events in 4 places:
1. In sctp_process_strreset_outreq(), the flag should always be set with
SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in
stream is reset here.
2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN
check, as the reset has to succeed after reconf_timer stops for the
in stream reset request retransmission.
3. In sctp_process_strreset_inreq(), no event should be sent, as no in
or out stream is reset here.
4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or
OUTGOING event should always be sent for stream reset requests, no
matter it fails or succeeds to process the request.
Fixes: 8105447645 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter")
Fixes: 16e1a91965 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter")
Fixes: 11ae76e67a ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24
Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst
With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the sock_diag interface for querying sockets from user
space. Tools like iproute2 ss(8) can use this interface to list open
AF_XDP sockets.
The user-space ABI is defined in linux/xdp_diag.h and includes netlink
request and response structs. The request can query sockets and the
response contains socket information about the rings, umems, inode and
more.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit adds an id to the umem structure. The id uniquely
identifies a umem instance, and will be exposed to user-space via the
socket monitoring interface.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Track each AF_XDP socket in a per-netns list. This will be used later
by the sock_diag interface for querying sockets from userspace.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There is a UBSAN bug report as below:
UBSAN: Undefined behaviour in net/netfilter/ipvs/ip_vs_ctl.c:2227:21
signed integer overflow:
-2147483647 * 1000 cannot be represented in type 'int'
Reproduce program:
#include <stdio.h>
#include <sys/types.h>
#include <sys/socket.h>
#define IPPROTO_IP 0
#define IPPROTO_RAW 255
#define IP_VS_BASE_CTL (64+1024+64)
#define IP_VS_SO_SET_TIMEOUT (IP_VS_BASE_CTL+10)
/* The argument to IP_VS_SO_GET_TIMEOUT */
struct ipvs_timeout_t {
int tcp_timeout;
int tcp_fin_timeout;
int udp_timeout;
};
int main() {
int ret = -1;
int sockfd = -1;
struct ipvs_timeout_t to;
sockfd = socket(AF_INET, SOCK_RAW, IPPROTO_RAW);
if (sockfd == -1) {
printf("socket init error\n");
return -1;
}
to.tcp_timeout = -2147483647;
to.tcp_fin_timeout = -2147483647;
to.udp_timeout = -2147483647;
ret = setsockopt(sockfd,
IPPROTO_IP,
IP_VS_SO_SET_TIMEOUT,
(char *)(&to),
sizeof(to));
printf("setsockopt return %d\n", ret);
return ret;
}
Return -EINVAL if the timeout value is negative or max than 'INT_MAX / HZ'.
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds the ability to read gso_segs from a BPF program.
v3: Use BPF_REG_AX instead of BPF_REG_TMP for the temporary register,
as suggested by Martin.
v2: refined Eddie Hao patch to address Alexei feedback.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eddie Hao <eddieh@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
net/tipc/link.c:1125:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:736:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:2418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building this code on a 32-bit platform such as ARM, there is a
link time error (lld error shown, happpens with ld.bfd too):
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by devlink.c
>>> net/core/devlink.o:(devlink_health_buffers_create) in archive built-in.a
This happens when using a regular division symbol with a u64 dividend.
Use DIV_ROUND_UP_ULL, which wraps do_div, to avoid this situation.
Fixes: cb5ccfbe73 ("devlink: Add health buffer support")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message gets logged far too often for how interesting is it.
Most distributions nowadays configure NetworkManager to use randomly
generated MAC addresses for Wi-Fi network scans. The interfaces end up
being periodically brought down for the address change. When they're
subsequently brought back up, the message is logged, eventually flooding
the log.
Perhaps the message is not all that helpful: it seems to be more
interesting to hear when the addrconf actually start, not when it does
not. Let's lower its level.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-By: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_put may fail, this fix add a check of its return value.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in6_dump_addrs() returns a positive 1 if there was nothing to dump.
This return value can not be passed as return from inet6_dump_addr()
as is, because it will confuse rtnetlink, resulting in NLMSG_DONE
never getting set:
$ ip addr list dev lo
EOF on netlink
Dump terminated
v2: flip condition to avoid a new goto (DaveA)
Fixes: 7c1e8a3817 ("netlink: fixup regression in RTM_GETADDR")
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the internal use of the skb_trimmed is reduced to
the ICMPv6/IGMP checksum verification. And for the length checks
the newly introduced helper functions are used instead of calculating
and checking with skb->len directly.
These changes should hopefully make it easier to verify that length
checks are performed properly.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-01-22
This series contains updates to i40e and xsk.
Jan exports xdp_get_umem_from_qid() for other drivers/modules to use.
Refactored the code use the netdev provided umems, instead of containing
them inside our i40e_vsi.
Aleksandr fixes an issue where RSS queues were misconfigured, so limit
the RSS queue number to the online CPU number.
Damian adds support for ethtool's setting and getting the FEC
configuration.
Grzegorz fixes a type mismatch, where the return value was not matching
the function declaration.
Sergey adds checks in the queue configuration handler to ensure the
number of queue pairs requested by the VF is less than maximum possible.
Lihong cleans up code left around from earlier silicon validation in the
i40e debugfs code.
Julia Lawall and Colin Ian King clean up white space indentation issues
found.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We must only extract l4 proto information if we can track the layer 4
protocol.
Before removal of pkt_to_tuple callback, the code to extract port
information was only reached for TCP/UDP/LITE/DCCP/SCTP.
The other protocols were handled by the indirect call, and the
'generic' tracker took care of other protocols that have no notion
of 'ports'.
After removal of the callback we must be more strict here and only
init port numbers for those protocols that have ports.
Fixes: df5e162908 ("netfilter: conntrack: remove pkt_to_tuple callback")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stephen Rothwell reports:
After merging the netfilter-next tree, today's linux-next build
(powerpc ppc64_defconfig) failed like this:
ERROR: "nf_conntrack_invert_icmpv6_tuple" [nf_conntrack.ko] undefined!
ERROR: "nf_conntrack_icmpv6_packet" [nf_conntrack.ko] undefined!
ERROR: "nf_conntrack_icmpv6_init_net" [nf_conntrack.ko] undefined!
ERROR: "icmpv6_pkt_to_tuple" [nf_conntrack.ko] undefined!
ERROR: "nf_ct_gre_keymap_destroy" [nf_conntrack.ko] undefined!
icmpv6 related errors are due to lack of IS_ENABLED(CONFIG_IPV6) (no
icmpv6 support is builtin if kernel has CONFIG_IPV6=n), the
nf_ct_gre_keymap_destroy error is due to lack of PROTO_GRE check.
Fixes: a47c540481 ("netfilter: conntrack: handle builtin l4proto packet functions via direct calls")
Fixes: e2e48b4716 ("netfilter: conntrack: handle icmp pkt_to_tuple helper via direct calls")
Fixes: 197c4300ae ("netfilter: conntrack: remove invert_tuple callback")
Fixes: 2a389de86e ("netfilter: conntrack: remove l4proto init and get_net callbacks")
Fixes: e56894356f ("netfilter: conntrack: remove l4proto destroy hook")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use ERSPAN key header field as tunnel key in gre_parse_header routine
since ERSPAN protocol sets the key field of the external GRE header to
0 resulting in a tunnel lookup fail in ip6gre_err.
In addition remove key field parsing and pskb_may_pull check in
erspan_rcv and ip6erspan_rcv
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build protos is required for tls_hw_prot also hence moved to
'tls_build_proto' and called as required from tls_init
and tls_hw_proto. This is required since build_protos
for v4 is moved from tls_register to tls_init in
commit <28cb6f1eaffdc5a6a9707cac55f4a43aa3fd7895>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been many people complaining about the inconsistent
behaviors of IPv4 and IPv6 devconf when creating new network
namespaces. Currently, for IPv4, we inherit all current settings
from init_net, but for IPv6 we reset all setting to default.
This patch introduces a new /proc file
/proc/sys/net/core/devconf_inherit_init_net to control the
behavior of whether to inhert sysctl current settings from init_net.
This file itself is only available in init_net.
As demonstrated below:
Initial setup in init_net:
# cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Default value 0 (current behavior):
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to 1 (inherit from init_net):
# echo 1 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Set to 2 (reset to default):
# echo 2 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
0
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to a value out of range (invalid):
# echo 3 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
# echo -1 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
Reported-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Reported-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export xdp_get_umem_from_qid for other modules to use.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).
Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2
Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26
Tested-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
con_fault() can transition the connection into STANDBY right after
ceph_con_keepalive() clears STANDBY in clear_standby():
libceph user thread ceph-msgr worker
ceph_con_keepalive()
mutex_lock(&con->mutex)
clear_standby(con)
mutex_unlock(&con->mutex)
mutex_lock(&con->mutex)
con_fault()
...
if KEEPALIVE_PENDING isn't set
set state to STANDBY
...
mutex_unlock(&con->mutex)
set KEEPALIVE_PENDING
set WRITE_PENDING
This triggers warnings in clear_standby() when either ceph_con_send()
or ceph_con_keepalive() get to clearing STANDBY next time.
I don't see a reason to condition queue_con() call on the previous
value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING
into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING
could have been a non-atomic flag.
Reported-by: syzbot+acdeb633f6211ccdf886@syzkaller.appspotmail.com
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Myungho Jung <mhjungk@gmail.com>
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
Daniel Borkmann says:
====================
pull-request: bpf 2019-01-20
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.
2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.
3) Fix map in map masking to prevent out-of-bounds access under
speculative execution, from Daniel.
4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
pacing, from Yuchung.
5) Fix json writer license in bpftool, from Thomas.
6) Fix AF_XDP to check if an actually queue exists during umem
setup, from Krzysztof.
7) Several fixes to BPF stackmap's build id handling. Another fix
for bpftool build to account for libbfd variations wrt linking
requirements, from Stanislav.
8) Fix BPF samples build with clang by working around missing asm
goto, from Yonghong.
9) Fix libbpf to retry program load on signal interrupt, from Lorenz.
10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
memcpy+0x23/0x50 mm/kasan/kasan.c:302
memcpy include/linux/string.h:345 [inline]
skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
__pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
__pskb_copy include/linux/skbuff.h:1053 [inline]
pskb_copy include/linux/skbuff.h:2904 [inline]
skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
__netdev_start_xmit include/linux/netdevice.h:4325 [inline]
netdev_start_xmit include/linux/netdevice.h:4334 [inline]
xmit_one net/core/dev.c:3219 [inline]
dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
__dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
__bpf_tx_skb net/core/filter.c:2016 [inline]
__bpf_redirect_common net/core/filter.c:2054 [inline]
__bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
____bpf_clone_redirect net/core/filter.c:2094 [inline]
bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000
The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.
Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.
Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.
The test itself can be run only from commit 1cf1cae963 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.
Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Similar to u32 filter, it is useful to know how many times
we reach each basic filter and how many times we pass the
ematch attached to it.
Sample output:
filter protocol arp pref 49152 basic chain 0
filter protocol arp pref 49152 basic chain 0 handle 0x1 (rule hit 3 success 3)
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1 installed 81 sec used 4 sec
Action statistics:
Sent 126 bytes 3 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable bugfixes:
- Fix TCP receive code on archs with flush_dcache_page()
Other bugfixes:
- Fix error code in rpcrdma_buffer_create()
- Fix a double free in rpcrdma_send_ctxs_create()
- Fix kernel BUG at kernel/cred.c:825
- Fix unnecessary retry in nfs42_proc_copy_file_range()
- Ensure rq_bytes_sent is reset before request transmission
- Ensure we respect the RPCSEC_GSS sequence number limit
- Address Kerberos performance/behavior regression
-----BEGIN PGP SIGNATURE-----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=6Nzz
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"These are mostly fixes for SUNRPC bugs, with a single v4.2
copy_file_range() fix mixed in.
Stable bugfixes:
- Fix TCP receive code on archs with flush_dcache_page()
Other bugfixes:
- Fix error code in rpcrdma_buffer_create()
- Fix a double free in rpcrdma_send_ctxs_create()
- Fix kernel BUG at kernel/cred.c:825
- Fix unnecessary retry in nfs42_proc_copy_file_range()
- Ensure rq_bytes_sent is reset before request transmission
- Ensure we respect the RPCSEC_GSS sequence number limit
- Address Kerberos performance/behavior regression"
* tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Address Kerberos performance/behavior regression
SUNRPC: Ensure we respect the RPCSEC_GSS sequence number limit
SUNRPC: Ensure rq_bytes_sent is reset before request transmission
NFSv4.2 fix unnecessary retry in nfs4_copy_file_range
sunrpc: kernel BUG at kernel/cred.c:825!
SUNRPC: Fix TCP receive code on archs with flush_dcache_page()
xprtrdma: Double free in rpcrdma_sendctxs_create()
xprtrdma: Fix error code in rpcrdma_buffer_create()
The only call site of sk_clone_lock is in inet_csk_clone_lock,
and sk_cookie will be set there.
So we don't need to set sk_cookie in sk_clone_lock().
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETADDRLABEL's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETADDR's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
v2: - improve extack messages (DaveA).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
v2: - new patch (DaveA).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETNSID's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
v2: - don't check size >= sizeof(struct rtgenmsg) (Nicolas).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETLINK's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the spirit of strict checks reject requests of stats the kernel
does not support when NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure NETLINK_GET_STRICT_CHK influences both GETSTATS doit
as well as the dump.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumps can read state of the NETLINK_F_STRICT_CHK flag from
a field in the callback structure. For non-dump GET requests
we need a way to access the state of that flag from a socket.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are now several places where qdisc_tree_reduce_backlog() is called
with a negative number of packets (to signal an increase in number of
packets in the queue). Rather than rely on overflow behaviour, change the
function signature to use signed integers to communicate this usage to
people reading the code.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware (e.g. MediaTek MT7603) cannot report A-MPDU length in tx status
information. Add support for a flag to indicate that, to allow minstrel_ht
to use a fixed value in its internal calculation (which gives better results
than just defaulting to 1).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This helps to reduce frequent path switches when multiple path
candidates have the same or very similar path metrics.
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use bitrate moving average to smooth out link metric and stablize path
selection.
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose path change count to destination in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose hop count to destination information in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow user to override STBC configuration for Rx and Tx spatial streams.
In practice RX/TX STBC settings can be modified using appropriate
options in wpa_supplicant configuration file:
tx_stbc=-1..1
rx_stbc=-1..3
This functionality has been added to wpa_supplicant in commit cdeea70f59d0.
In FullMAC case these STBC options are passed to drivers by cfg80211
connect callback in fields of cfg80211_connect_params structure.
However for mac80211 drivers, e.g. for mac80211_hwsim,
overrides for STBC settings are ignored.
The reason why RX/TX STBC capabilities are not modified for mac80211
drivers is as follows. All drivers need to specify supported HT/VHT
overrides explicitly: see ht_capa_mod_mask and vht_capa_mod_mask fields
of wiphy structure. Only supported overrides will be passed to drivers by
cfg80211_connect and cfg80211_mlme_assoc operations: see bitwise 'AND'
performed by cfg80211_oper_and_ht_capa and cfg80211_oper_and_vht_capa.
This commit adds RX/TX STBC HT capabilities to mac80211_ht_capa_mod_mask,
allowing their modifications, as well as applies requested STBC
modifications in function ieee80211_apply_htcap_overrides.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds TX airtime statistics to the cfg80211 station dump (to go along
with the RX info already present), and adds a new parameter to set the
airtime weight of each station. The latter allows userspace to implement
policies for different stations by varying their weights.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[move airtime weight != 0 check into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero. For unicast frames
destined for other hosts, we stop processing the frame at that point.
For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA. That
doesn't match the usual definition of "dropped," so don't count
those as such.
With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
as there is no other dump which is already stored)
* Auto recovery attempt is being done. depends on:
- Auto Recovery configuration
- Grace period vs. time since last recover
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.
As part of the allocation, driver shall provide a set of callbacks which
will be used the devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.
For each reporter, devlink will hold a metadata of statistics,
buffers and status.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health buffer is a mechanism to pass descriptors between drivers
and devlink. The API allows the driver to add objects, object pair,
value array (nested attributes), value and name.
Driver can use this API to fill the buffers in a format which can be
translated by the devlink to the netlink message.
In order to fulfill it, an internal buffer descriptor is defined. This
will hold the data and metadata per each attribute and by used to pass
actual commands to the netlink.
This mechanism will be later used in devlink health for dump and diagnose
data store by the drivers.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although matchall always matches packets, however, it still
relies on a protocol match first. So it is still useful to have
such a counter for matchall. Of course, unlike u32, every time
we hit a matchall filter, it is always a success, so we don't
have to distinguish them.
Sample output:
filter protocol 802.1Q pref 100 matchall chain 0
filter protocol 802.1Q pref 100 matchall chain 0 handle 0x1
not_in_hw (rule hit 10)
action order 1: vlan pop continue
index 1 ref 1 bind 1 installed 40 sec used 1 sec
Action statistics:
Sent 836 bytes 10 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove gre_hdr_len from ip6erspan_rcv routine signature since
it is not longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A better way to implement this from userspace has been found without
specific code in the kernel side, revert this.
Fixes: b9ccc07e3f ("netfilter: nft_hash: add map lookups for hashing operations")
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Not used since 203f2e7820 ("netfilter: nat: remove l4proto->unique_tuple")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the ip_rcv the skb goes through the PREROUTING hook first, then kicks
in vrf device and go through the same hook again. When conntrack dnat
works with vrf, there will be some conflict with rules because the
packet goes through the hook twice with different nf status.
ip link add user1 type vrf table 1
ip link add user2 type vrf table 2
ip l set dev tun1 master user1
ip l set dev tun2 master user2
nft add table firewall
nft add chain firewall zones { type filter hook prerouting priority - 300 \; }
nft add rule firewall zones counter ct zone set iif map { "tun1" : 1, "tun2" : 2 }
nft add chain firewall rule-1000-ingress
nft add rule firewall rule-1000-ingress ct zone 1 tcp dport 22 ct state new counter accept
nft add rule firewall rule-1000-ingress counter drop
nft add chain firewall rule-1000-egress
nft add rule firewall rule-1000-egress tcp dport 22 ct state new counter drop
nft add rule firewall rule-1000-egress counter accept
nft add chain firewall rules-all { type filter hook prerouting priority - 150 \; }
nft add rule firewall rules-all ip daddr vmap { "2.2.2.11" : jump rule-1000-ingress }
nft add rule firewall rules-all ct zone vmap { 1 : jump rule-1000-egress }
nft add rule firewall dnat-all ct zone vmap { 1 : jump dnat-1000 }
nft add rule firewall dnat-1000 ip daddr 2.2.2.11 counter dnat to 10.0.0.7
For a package with ip daddr 2.2.2.11 and tcp dport 22, first time accept in the
rule-1000-ingress and dnat to 10.0.0.7. Then second time the packet goto the wrong
chain rule-1000-egress which leads the packet drop
With this patch, userspace can add the 'don't re-do entire ruleset for
vrf' policy itself via:
nft add rule firewall rules-all meta iifkind "vrf" counter accept
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The connection tracking hooks can be optionally registered per netns
when conntrack is specifically invoked from the ruleset since
0c66dc1ea3 ("netfilter: conntrack: register hooks in netns when needed
by ruleset"). Then, since 4d3a57f23d ("netfilter: conntrack: do not
enable connection tracking unless needed"), the default behaviour is
changed to always register them on demand.
This patch provides a toggle that allows users to always register them.
Without this toggle, in order to use conntrack for statistics
collection, you need a dummy rule that refers to conntrack, eg.
iptables -I INPUT -m state --state NEW
This patch allows users to restore the original behaviour via modparam,
ie. always register connection tracking, eg.
modprobe nf_conntrack enable_hooks=1
Hence, no dummy rule is required.
Reported-by: Laura Garcia <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Its now same as __nf_ct_l4proto_find(), so rename that to
nf_ct_l4proto_find and use it everywhere.
It never returns NULL and doesn't need locks or reference counts.
Before this series:
302824 net/netfilter/nf_conntrack.ko
21504 net/netfilter/nf_conntrack_proto_gre.ko
text data bss dec hex filename
6281 1732 4 8017 1f51 nf_conntrack_proto_gre.ko
108356 20613 236 129205 1f8b5 nf_conntrack.ko
After:
294864 net/netfilter/nf_conntrack.ko
text data bss dec hex filename
106979 19557 240 126776 1ef38 nf_conntrack.ko
so, even with builtin gre, total size got reduced.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Only one user (gre), add a direct call and remove this facility.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Those were needed we still had modular trackers.
As we don't have those anymore, prefer direct calls and remove all
the (un)register infrastructure associated with this.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to historical reasons, all l4 trackers register their own
sysctls.
This leads to copy&pasted boilerplate code, that does exactly same
thing, just with different data structure.
Place all of this in a single file.
This allows to remove the various ctl_table pointers from the ct_netns
structure and reduces overall code size.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
after removal of the packet and invert function pointers, several
places do not need to lookup the l4proto structure anymore.
Remove those lookups.
The function nf_ct_invert_tuplepr becomes redundant, replace
it with nf_ct_invert_tuple everywhere.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that all l4trackers are builtin, no need to use a mix of direct and
indirect calls.
This removes the last two users: gre and the generic l4 protocol
tracker.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to get/put module owner reference, none of these can be removed
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Only used by icmp(v6). Prefer a direct call and remove this
function from the l4proto struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
GRE is now builtin, so we can handle it via direct call and
remove the callback.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes the last of the modular l4 trackers 'bool'.
After this, all infrastructure to handle dynamic l4 protocol registration
becomes obsolete and can be removed in followup patches.
Old:
302824 net/netfilter/nf_conntrack.ko
21504 net/netfilter/nf_conntrack_proto_gre.ko
New:
313728 net/netfilter/nf_conntrack.ko
Old:
text data bss dec hex filename
6281 1732 4 8017 1f51 nf_conntrack_proto_gre.ko
108356 20613 236 129205 1f8b5 nf_conntrack.ko
New:
112095 21381 240 133716 20a54 nf_conntrack.ko
The size increase is only temporary.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can use gre. Lock is only needed when a new expectation is added.
In case a single spinlock proves to be problematic we can either add one
per netns or use an array of locks combined with net_hash_mix() or similar
to pick the 'correct' one.
But given this is only needed for an expectation rather than per packet
a single one should be ok.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
rather than handling them via indirect call, use a direct one instead.
This leaves GRE as the last user of this indirect call facility.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The l4 protocol trackers are invoked via indirect call: l4proto->packet().
With one exception (gre), all l4trackers are builtin, so we can make
.packet optional and use a direct call for most protocols.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To allow for a batch to contain rules in arbitrary ordering, introduce
NFTA_RULE_POSITION_ID attribute which works just like NFTA_RULE_POSITION
but contains the ID of another rule within the same batch. This helps
iptables-nft-restore handling dumps with mixed insert/append commands
correctly.
Note that NFTA_RULE_POSITION takes precedence over
NFTA_RULE_POSITION_ID, so if the former is present, the latter is
ignored.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
place them into the confirm one.
Old:
hook (300): ipv4/6_help() first call helper, then seqadj.
hook (INT_MAX): confirm
Now:
hook (INT_MAX): confirm, first call helper, then seqadj, then confirm
Not having the extra call is noticeable in bechmarks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With CONFIG_RETPOLINE its faster to add an if (ptr == &foo_func)
check and and use direct calls for all the built-in expressions.
~15% improvement in pathological cases.
checkpatch doesn't like the X macro due to the embedded return statement,
but the macro has a very limited scope so I don't think its a problem.
I would like to avoid bugs of the form
If (e->ops->eval == (unsigned long)nft_foo_eval)
nft_bar_eval();
and open-coded if ()/else if()/else cascade, thus the macro.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of linear search, use rhlist interface to look up the objects.
This fixes rulesets with thousands of named objects (quota, counters and
the like).
We only use a single table for this and consider the address of the
table we're doing the lookup in as a part of the key.
This reduces restore time of a sample ruleset with ~20k named counters
from 37 seconds to 0.8 seconds.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a 'key' structure for object, so we can look them up by name + table
combination (the name can be the same in each table).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have proper tp->rack value,
then a clone will also inherit proper initial value.
Note that fresh sockets init tp->rack from tcp_init_sock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have app_limited set to ~0U,
then a clone will also inherit proper initial value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.
So a clone will inherit a zero value here.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passive connections can inherit proper value by cloning,
if we make sure all listeners have the proper values there.
tcp_disconnect() was setting snd_cwnd to 2, which seems
quite obsolete since IW10 adoption.
Also remove an obsolete comment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure a listener always has its mdev_us
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.
tcp_disconnect() is very seldom used in real applications.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.
So a clone will inherit a zero value here.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sockets have this field cleared, and tcp_disconnect()
calls tcp_write_queue_purge() which among other things
also clear tp->packets_out
So a listener is guaranteed to have this field cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure a listener always has its icsk_rto
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.
tcp_disconnect() is very seldom used in real applications.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sockets get the field set to TCP_INFINITE_SSTHRESH in tcp_init_sock()
In case a socket had this field changed and transitions to TCP_LISTEN
state, tcp_disconnect() also makes sure snd_ssthresh is set to
TCP_INFINITE_SSTHRESH.
So a listener has this field set to TCP_INFINITE_SSTHRESH already.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nft_compat destroy function deletes the nft_xt object from a list.
This isn't allowed anymore. Destroy functions are called asynchronously,
i.e. next batch can find the object that has a pending ->destroy()
invocation:
cpu0 cpu1
worker
->destroy for_each_entry()
if (x == ...
return x->ops;
list_del(x)
kfree_rcu(x)
expr->ops->... // ops was free'd
To resolve this, the list_del needs to occur before the transaction
mutex gets released. nf_tables has a 'deactivate' hook for this
purpose, so use that to unlink the object from the list.
Fixes: 0935d55884 ("netfilter: nf_tables: asynchronous release")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are two problems with nft_compat since the netlink config
plane uses a per-netns mutex:
1. Concurrent add/del accesses to the same list
2. accesses to a list element after it has been free'd already.
This patch fixes the first problem.
Freeing occurs from a work queue, after transaction mutexes have been
released, i.e., it still possible for a new transaction (even from
same net ns) to find the to-be-deleted expression in the list.
The ->destroy functions are not allowed to have any such side effects,
i.e. the list_del() in the destroy function is not allowed.
This part of the problem is solved in the next patch.
I tried to make this work by serializing list access via mutex
and by moving list_del() to a deactivate callback, but
Taehee spotted following race on this approach:
NET #0 NET #1
>select_ops()
->init()
->select_ops()
->deactivate()
->destroy()
nft_xt_put()
kfree_rcu(xt, rcu_head);
->init() <-- use-after-free occurred.
Unfortunately, we can't increment reference count in
select_ops(), because we can't undo the refcount increase in
case a different expression fails in the same batch.
(The destroy hook will only be called in case the expression
was initialized successfully).
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Using standard integer type was fine while all operations on it were
guarded by the nftnl subsys mutex.
This isn't true anymore:
1. transactions are guarded only by a pernet mutex, so concurrent
rule manipulation in different netns is racy
2. the ->destroy hook runs from a work queue after the transaction
mutex has been released already.
cpu0 cpu1 (net 1) cpu2 (net 2)
kworker
nft_compat->destroy nft_compat->init nft_compat->init
if (--nft_xt->ref == 0) nft_xt->ref++ nft_xt->ref++
Switch to refcount_t. Doing this however only fixes a minor aspect,
nft_compat also performs linked-list operations in an unsafe way.
This is addressed in the next two patches.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Fixes: 0935d55884 ("netfilter: nf_tables: asynchronous release")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit cb9f1b7838, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:
Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00💯:1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
TX: bytes packets errors dropped carrier collsns
0 0 1 0 0 0
The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).
This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b7838 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some testing scenarios, dst/route cache can fill up so quickly
that even an explicit GC call occasionally fails to clean it up. This leads
to sporadically failing calls to dst_alloc and "network unreachable" errors
to the user, which is confusing.
This patch adds a diagnostic message to make the cause of the failure
easier to determine.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sch_fq packet scheduler is not used, TCP can fallback to
internal pacing, but this requires sk_pacing_status to
be properly set.
Fixes: 8c4b4c7e9f ("bpf: Add setsockopt helper function to bpf")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In sock_setsockopt() (net/core/sock.h), when SO_MARK option is used
to change sk_mark, sk_dst_reset(sk) is called. The same should be
done in bpf_setsockopt().
Fixes: 8c4b4c7e9f ("bpf: Add setsockopt helper function to bpf")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when the sender fails to send (original) data packet or
window probes due to congestion in the local host (e.g. throttling
in qdisc), it'll retry within an RTO or two up to 500ms.
In low-RTT networks such as data-centers, RTO is often far below
the default minimum 200ms. Then local host congestion could trigger
a retry storm pouring gas to the fire. Worse yet, the probe counter
(icsk_probes_out) is not properly updated so the aggressive retry
may exceed the system limit (15 rounds) until the packet finally
slips through.
On such rare events, it's wise to retry more conservatively
(500ms) and update the stats properly to reflect these incidents
and follow the system limit. Note that this is consistent with
the behaviors when a keep-alive probe or RTO retry is dropped
due to local congestion.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when the sender fails to retransmit a data packet on
timeout due to congestion in the local host (e.g. throttling in
qdisc), it'll retry within an RTO up to 500ms.
In low-RTT networks such as data-centers, RTO is often far
below the default minimum 200ms (and the cap 500ms). Then local
host congestion could trigger a retry storm pouring gas to the
fire. Worse yet, the retry counter (icsk_retransmits) is not
properly updated so the aggressive retry may exceed the system
limit (15 rounds) until the packet finally slips through.
On such rare events, it's wise to retry more conservatively (500ms)
and update the stats properly to reflect these incidents and follow
the system limit. Note that this is consistent with the behavior
when a keep-alive probe is dropped due to local congestion.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we use the next unsent skb's timestamp to determine
when to abort a socket stalling on window probes. This no longer
works as skb timestamp reflects the last instead of the first
transmission.
Instead we can estimate how long the socket has been stalling
with the probe count and the exponential backoff behavior.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper to model TCP exponential backoff for the next patch.
This is pure refactor w no behavior change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a corner issue on timeout behavior of a
passive Fast Open socket. A passive Fast Open server may write
and close the socket when it is re-trying SYN-ACK to complete
the handshake. After the handshake is completely, the server does
not properly stamp the recovery start time (tp->retrans_stamp is
0), and the socket may abort immediately on the very first FIN
timeout, instead of retying until it passes the system or user
specified limit.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP socket's retrans_stamp is not set if the
retransmission has failed to send. As a result if a socket is
experiencing local issues to retransmit packets, determining when
to abort a socket is complicated w/o knowning the starting time of
the recovery since retrans_stamp may remain zero.
This complication causes sub-optimal behavior that TCP may use the
latest, instead of the first, retransmission time to compute the
elapsed time of a stalling connection due to local issues. Then TCP
may disrecard TCP retries settings and keep retrying until it finally
succeed: not a good idea when the local host is already strained.
The simple fix is to always timestamp the start of a recovery.
It's worth noting that retrans_stamp is also used to compare echo
timestamp values to detect spurious recovery. This patch does
not break that because retrans_stamp is still later than when the
original packet was sent.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP skbs are not always timestamped if the transmission
failed due to memory or other local issues. This makes deciding
when to abort a socket tricky and complicated because the first
unacknowledged skb's timestamp may be 0 on TCP timeout.
The straight-forward fix is to always timestamp skb on every
transmission attempt. Also every skb retransmission needs to be
flagged properly to avoid RTT under-estimation. This can happen
upon receiving an ACK for the original packet and the a previous
(spurious) retransmission has failed.
It's worth noting that this reverts to the old time-stamping
style before commit 8c72c65b42 ("tcp: update skb->skb_mstamp more
carefully") which addresses a problem in computing the elapsed time
of a stalled window-probing socket. The problem will be addressed
differently in the next patches with a simpler approach.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP only warns if its RTO timer fires and the
retransmission queue is empty, but it'll cause null pointer
reference later on. It's better to avoid such catastrophic failure
and simply exit with a warning.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 23b0269e58 ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.
And this issue was found with LTP/network tests as well.
Fixes: 23b0269e58 ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4cdeeee925 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.
The issue was found with LTP/network tests (UDP-Lite test-cases).
Fixes: 4cdeeee925 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp-tunnel setup allows binding sockets to a network device. Prefer
the new SO_BINDTOIFINDEX to avoid temporarily resolving the device-name
just to look it up in the ioctl again.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp-tunnel setup allows binding sockets to a network device. Prefer
the new SO_BINDTOIFINDEX to avoid temporarily resolving the device-name
just to look it up in the ioctl again.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new generic SOL_SOCKET-level socket option called
SO_BINDTOIFINDEX. It behaves similar to SO_BINDTODEVICE, but takes a
network interface index as argument, rather than the network interface
name.
User-space often refers to network-interfaces via their index, but has
to temporarily resolve it to a name for a call into SO_BINDTODEVICE.
This might pose problems when the network-device is renamed
asynchronously by other parts of the system. When this happens, the
SO_BINDTODEVICE might either fail, or worse, it might bind to the wrong
device.
In most cases user-space only ever operates on devices which they
either manage themselves, or otherwise have a guarantee that the device
name will not change (e.g., devices that are UP cannot be renamed).
However, particularly in libraries this guarantee is non-obvious and it
would be nice if that race-condition would simply not exist. It would
make it easier for those libraries to operate even in situations where
the device-name might change under the hood.
A real use-case that we recently hit is trying to start the network
stack early in the initrd but make it survive into the real system.
Existing distributions rename network-interfaces during the transition
from initrd into the real system. This, obviously, cannot affect
devices that are up and running (unless you also consider moving them
between network-namespaces). However, the network manager now has to
make sure its management engine for dormant devices will not run in
parallel to these renames. Particularly, when you offload operations
like DHCP into separate processes, these might setup their sockets
early, and thus have to resolve the device-name possibly running into
this race-condition.
By avoiding a call to resolve the device-name, we no longer depend on
the name and can run network setup of dormant devices in parallel to
the transition off the initrd. The SO_BINDTOIFINDEX ioctl plugs this
race.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes (especially 05cd271fd6 ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.
v2:
- use kzalloc() instead of kcalloc()
Fixes: 05cd271fd6 ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes recvmsg() to be able to peek across multiple tls records.
Without this patch, the tls's selftests test case
'recv_peek_large_buf_mult_recs' fails. Each tls receive context now
maintains a 'rx_list' to retain incoming skb carrying tls records. If a
tls record needs to be retained e.g. for peek case or for the case when
the buffer passed to recvmsg() has a length smaller than decrypted
record length, then it is added to 'rx_list'. Additionally, records are
added in 'rx_list' if the crypto operation runs in async mode. The
records are dequeued from 'rx_list' after the decrypted data is consumed
by copying into the buffer passed to recvmsg(). In case, the MSG_PEEK
flag is used in recvmsg(), then records are not consumed or removed
from the 'rx_list'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/tls/tls_sw.c:1023:5: warning:
symbol 'tls_sw_do_sendpage' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function sk_msg_clone has been modified to merge the data from source sg
entry to destination sg entry if the cloned data resides in same page
and is contiguous to the end entry of destination sk_msg. This improves
kernel tls throughput to the tune of 10%.
When the user space tls application calls sendmsg() with MSG_MORE, it leads
to calling sk_msg_clone() with new data being cloned placed continuous to
previously cloned data. Without this optimization, a new SG entry in
the destination sk_msg i.e. rec->msg_plaintext in tls_clone_plaintext_msg()
gets used. This leads to exhaustion of sg entries in rec->msg_plaintext
even before a full 16K of allowable record data is accumulated. Hence we
lose oppurtunity to encrypt and send a full 16K record.
With this patch, the kernel tls can accumulate full 16K of record data
irrespective of the size of data passed in sendmsg() with MSG_MORE.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warnings (W=1).
To preserve as much of the existing comment only change a ‘:’ into a ‘,’.
This is enough change, to match the regular expression expected by GCC.
This commit removes the following warning:
net/core/filter.c:5310:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Mathieu Malaterre