strict_strtoul() has been made __must_check so do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We unconditionally require SYSCLK since while only microphone detection
specifically requires SYSCLK any actual use case would enable it via
some other means but microphone detection may have nothing active other
than the bias itself.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reduce the source code size still futher by only specifying non-zero
rows in the WM8962 access map.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Dramatically reduce the code size for the WM8962 register defaults table
by switching to explicitly initialise only defined registers, relying on
static defaulting to zero for the overwelming bulk of the register map.
Similar treatement for the register access table will come later and will
produce a similarly dramatic code size shrink.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
GPIO2 and GPIO3 on the WM8962 are MFPs and need to be put into GPIO mode
before the GPIO block can be used to control them. We're already doing
this when used via gpiolib, factor out the code for use when setting static
configurations via platform data as well.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow microphone detection on WM8962 to be performed using the interrupt
signal, allowing the detection of both microphone presence and button
presses with a signal singal from the CODEC to CPU. Currently a 250ms
debounce time is applied to both short circuit and presence detection,
this has not been optimised.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8962 features five GPIOs, add support for controlling their output
state via gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The restrictions on configuring BCLK are overly cautious, other constraints
in the system should ensure that reconfiguration is not possible when the
device is sufficiently active to be unable to support reclocking.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add the widget for MICBIAS power control and allow configuration of the
microphone bias setup via the platform data for the WM8962. When
microphone status signals are brought out to GPIO this should be
sufficient to enable microphone detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide an initial hookup for interrupts on the WM8962. Currently we simply
report error status via log messages if an IRQ is provided for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When configuring the FLL we preserve the FLL enable configuration in order
to allow us to reenable the FLL after configuration but we do not clear
the other bits in the register, causing old configuration to be preserved.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is a simple off-by-one bug, the size of the register cache is
incorrectly set to the maximum register index. Fix it by adding one.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 is a low power, high performance stereo CODEC designed for
portable digital audio applications.
This initial driver release supports the key audio paths of the WM8962.
Extended functionality, such as microphone detection, digital microphones
and the advanced DSP signal enhancements provided by the device are not
yet supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown