Notifiers are required only for conservative governor and the common
governor code is unnecessarily polluted with that. Handle that from
cs_init/exit() instead of cpufreq_governor_dbs().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, ondemand calculates the target frequency proportional to load
using the formula:
Target frequency = C * load
where C = policy->cpuinfo.max_freq / 100
Though, in many cases, the minimum available frequency is pretty high and
the above calculation introduces a dead band from load 0 to
100 * policy->cpuinfo.min_freq / policy->cpuinfo.max_freq where the target
frequency is always calculated to less than policy->cpuinfo.min_freq and
the minimum frequency is selected.
For example: on Intel i7-3770 @ 3.4GHz the policy->cpuinfo.min_freq = 1600000
and the policy->cpuinfo.max_freq = 3400000 (without turbo). Thus, the CPU
starts to scale up at a load above 47.
On quad core 1500MHz Krait the policy->cpuinfo.min_freq = 384000
and the policy->cpuinfo.max_freq = 1512000. Thus, the CPU starts to scale
at load above 25.
Change the calculation of target frequency to eliminate the above effect using
the formula:
Target frequency = A + B * load
where A = policy->cpuinfo.min_freq and
B = (policy->cpuinfo.max_freq - policy->cpuinfo->min_freq) / 100
This will map load values 0 to 100 linearly to cpuinfo.min_freq to
cpuinfo.max_freq.
Also, use the CPUFREQ_RELATION_C in __cpufreq_driver_target to select the
closest frequency in frequency_table. This is necessary to avoid selection
of minimum frequency only when load equals to 0. It will also help for selection
of frequencies using a more 'fair' criterion.
Tables below show the difference in selected frequency for specific values
of load without and with this patch. On Intel i7-3770 @ 3.40GHz:
Without With
Load Target Selected Target Selected
0 0 1600000 1600000 1600000
5 170050 1600000 1690050 1700000
10 340100 1600000 1780100 1700000
15 510150 1600000 1870150 1900000
20 680200 1600000 1960200 2000000
25 850250 1600000 2050250 2100000
30 1020300 1600000 2140300 2100000
35 1190350 1600000 2230350 2200000
40 1360400 1600000 2320400 2400000
45 1530450 1600000 2410450 2400000
50 1700500 1900000 2500500 2500000
55 1870550 1900000 2590550 2600000
60 2040600 2100000 2680600 2600000
65 2210650 2400000 2770650 2800000
70 2380700 2400000 2860700 2800000
75 2550750 2600000 2950750 3000000
80 2720800 2800000 3040800 3000000
85 2890850 2900000 3130850 3100000
90 3060900 3100000 3220900 3300000
95 3230950 3300000 3310950 3300000
100 3401000 3401000 3401000 3401000
On ARM quad core 1500MHz Krait:
Without With
Load Target Selected Target Selected
0 0 384000 384000 384000
5 75600 384000 440400 486000
10 151200 384000 496800 486000
15 226800 384000 553200 594000
20 302400 384000 609600 594000
25 378000 384000 666000 702000
30 453600 486000 722400 702000
35 529200 594000 778800 810000
40 604800 702000 835200 810000
45 680400 702000 891600 918000
50 756000 810000 948000 918000
55 831600 918000 1004400 1026000
60 907200 918000 1060800 1026000
65 982800 1026000 1117200 1134000
70 1058400 1134000 1173600 1134000
75 1134000 1134000 1230000 1242000
80 1209600 1242000 1286400 1242000
85 1285200 1350000 1342800 1350000
90 1360800 1458000 1399200 1350000
95 1436400 1458000 1455600 1458000
100 1512000 1512000 1512000 1512000
Tested on Intel i7-3770 CPU @ 3.40GHz and on ARM quad core 1500MHz Krait
(Android smartphone).
Benchmarks on Intel i7 shows a performance improvement on low and medium
work loads with lower power consumption. Specifics:
Phoronix Linux Kernel Compilation 3.1:
Time: -0.40%, energy: -0.07%
Phoronix Apache:
Time: -4.98%, energy: -2.35%
Phoronix FFMPEG:
Time: -6.29%, energy: -4.02%
Also, running mp3 decoding (very low load) shows no differences with and
without this patch.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit dfa5bb6225 (cpufreq: ondemand: Change the calculation
of target frequency), this return statement is no longer needed.
Reported-by: Henrik Nilsson <Karl.Henrik.Nilsson@gmail.com>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Function __cpufreq_driver_target() checks if target_freq is within
policy->min and policy->max range. generic_powersave_bias_target() also
checks if target_freq is valid via a cpufreq_frequency_table_target()
call. So, drop the unnecessary duplicate check in *_check_cpu().
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Chapter 14 of Documentation/CodingStyle says:
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts
readability and introduces an opportunity for a bug when the pointer
variable type is changed but the corresponding sizeof that is passed
to a memory allocator is not.
This wasn't followed consistently in drivers/cpufreq, let's make it
more consistent by always following this rule.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They are called policy, cur_policy, new_policy, data, etc. Just call
them policy wherever possible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch addresses the following issues in the header files in the
cpufreq core:
- Include headers in ascending order, so that we don't add same
many times by mistake.
- <asm/> must be included after <linux/>, so that they override
whatever they need to.
- Remove unnecessary includes.
- Don't include files already included by cpufreq.h or
cpufreq_governor.h.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This sysfs file was called ignore_nice_load earlier and commit
4d5dcc4 (cpufreq: governor: Implement per policy instances of
governors) changed its name to ignore_nice by mistake.
Lets get it renamed back to its original name.
Reported-by: Martin von Gagern <Martin.vGagern@gmx.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ondemand governor calculates load in terms of frequency and
increases it only if load_freq is greater than up_threshold
multiplied by the current or average frequency. This appears to
produce oscillations of frequency between min and max because,
for example, a relatively small load can easily saturate minimum
frequency and lead the CPU to the max. Then, it will decrease
back to the min due to small load_freq.
Change the calculation method of load and target frequency on the
basis of the following two observations:
- Load computation should not depend on the current or average
measured frequency. For example, absolute load of 80% at 100MHz
is not necessarily equivalent to 8% at 1000MHz in the next
sampling interval.
- It should be possible to increase the target frequency to any
value present in the frequency table proportional to the absolute
load, rather than to the max only, so that:
Target frequency = C * load
where we take C = policy->cpuinfo.max_freq / 100.
Tested on Intel i7-3770 CPU @ 3.40GHz and on Quad core 1500MHz Krait.
Phoronix benchmark of Linux Kernel Compilation 3.1 test shows an
increase ~1.5% in performance. cpufreq_stats (time_in_state) shows
that middle frequencies are used more, with this patch. Highest
and lowest frequencies were used less by ~9%.
[rjw: We have run multiple other tests on kernels with this
change applied and in the vast majority of cases it turns out
that the resulting performance improvement also leads to reduced
consumption of energy. The change is additionally justified by
the overall simplification of the code in question.]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When initializing the default powersave_bias value, we need to first
make sure that this policy is running the ondemand governor.
Reported-and-tested-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I don't see how the virtual address of the tuners pointer would be of
any help to anyone so remove it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This allows for another [arch specific] driver to hook into existing
powersave bias function of the ondemand governor. i.e. This allows AMD
specific powersave bias function (in a separate AMD specific driver)
to aid ondemand governor's frequency transition decisions.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we always calculate the CPU iowait time and add it to idle time.
If we are in ondemand and we use io_is_busy, we re-calculate iowait time
and we subtract it from idle time.
With this patch iowait time is calculated only when necessary avoiding
the double call to get_cpu_iowait_time_us. We use a parameter in
function get_cpu_idle_time to distinguish when the iowait time will be
added to idle time or not, without the need of keeping the prev_io_wait.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.,org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Following patch has introduced per cpu timers or works for ondemand and
conservative governors.
commit 2abfa876f1
Author: Rickard Andersson <rickard.andersson@stericsson.com>
Date: Thu Dec 27 14:55:38 2012 +0000
cpufreq: handle SW coordinated CPUs
This causes additional unnecessary interrupts on all cpus when the load is
recently evaluated by any other cpu. i.e. When load is recently evaluated by cpu
x, we don't really need any other cpu to evaluate this load again for the next
sampling_rate time.
Some sort of code is present to avoid that but we are still getting timer
interrupts for all cpus. A good way of avoiding this would be to modify delays
for all cpus (policy->cpus) whenever any cpu has evaluated load.
This patch does this change and some related code cleanup.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because we have per cpu timer now, we check if we need to evaluate load again or
not (In case it is recently evaluated). Here the 2nd cpu which got timer
interrupt updates core_dbs_info->sample_type irrespective of load evaluation is
required or not. Which is wrong as the first cpu is dependent on this variable
set to an older value.
Moreover it would be best in this case to schedule 2nd cpu's timer to
sampling_rate instead of freq_lo or hi as that must be managed by the other cpu.
In case the other cpu idles in between then also we wouldn't loose much power.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch uses the infrastructure provided by earlier patch and
implements init/exit routines for ondemand and conservative
governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix some typos in comments.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to avoid the calculation of up_threshold - down_differential
every time that the frequency must be decreased, we replace the
down_differential tuner with the adj_up_threshold which keeps the
difference across multiple checks.
Update the adj_up_threshold only when the up_theshold is also updated.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the inclusion of following patches:
9f4eb10 cpufreq: conservative: call dbs_check_cpu only when necessary
772b4b1 cpufreq: ondemand: call dbs_check_cpu only when necessary
code redundancy between the conservative and ondemand governors is
introduced again, so get rid of it.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix governors code to set all cpu's cdbs->cpu to the the actual cpu id
and use cur_policy->cpu istead of cdbs->cpu to track current governor's
leader cpu.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Implement a generic helper function policy_is_shared() to replace the
current dbs_sw_coordinated_cpus() at cpufreq level, so that it can be
used by code other than cpufreq governors.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify update_sampling_rate() to check, and eventually immediately
schedule, all CPU's do_dbs_timer delayed work.
This is required in case of software coordinated CPUs, as we now have a
separate delayed work for each CPU.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify ondemand timer to not resample CPU utilization if recently
sampled from another SW coordinated core.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes a bug that occurred when we had load on a secondary CPU
and the primary CPU was sleeping. Only one sampling timer was spawned
and it was spawned as a deferred timer on the primary CPU, so when a
secondary CPU had a change in load this was not detected by the cpufreq
governor (both ondemand and conservative).
This patch make sure that deferred timers are run on all CPUs in the
case of software controlled CPUs that run on the same frequency.
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix cpufreq_gov_ondemand to skip CPU where another governor is used.
The bug present itself as NULL pointer access on the mutex_lock() call,
an can be reproduced on an SMP machine by setting the default governor
to anything other than ondemand, setting a single CPU's governor to
ondemand, then changing the sample rate by writing on:
> /sys/devices/system/cpu/cpufreq/ondemand/sampling_rate
Backtrace:
Nov 26 17:36:54 balto kernel: [ 839.585241] BUG: unable to handle kernel NULL pointer dereference at (null)
Nov 26 17:36:54 balto kernel: [ 839.585311] IP: [<ffffffff8174e082>] __mutex_lock_slowpath+0xb2/0x170
[snip]
Nov 26 17:36:54 balto kernel: [ 839.587005] Call Trace:
Nov 26 17:36:54 balto kernel: [ 839.587030] [<ffffffff8174da82>] mutex_lock+0x22/0x40
Nov 26 17:36:54 balto kernel: [ 839.587067] [<ffffffff81610b8f>] store_sampling_rate+0xbf/0x150
Nov 26 17:36:54 balto kernel: [ 839.587110] [<ffffffff81031e9c>] ? __do_page_fault+0x1cc/0x4c0
Nov 26 17:36:54 balto kernel: [ 839.587153] [<ffffffff813309bf>] kobj_attr_store+0xf/0x20
Nov 26 17:36:54 balto kernel: [ 839.587192] [<ffffffff811bb62d>] sysfs_write_file+0xcd/0x140
Nov 26 17:36:54 balto kernel: [ 839.587234] [<ffffffff8114c12c>] vfs_write+0xac/0x180
Nov 26 17:36:54 balto kernel: [ 839.587271] [<ffffffff8114c472>] sys_write+0x52/0xa0
Nov 26 17:36:54 balto kernel: [ 839.587306] [<ffffffff810321ce>] ? do_page_fault+0xe/0x10
Nov 26 17:36:54 balto kernel: [ 839.587345] [<ffffffff81751202>] system_call_fastpath+0x16/0x1b
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Restore the correct delay value for ondemand's od_dbs_timer, as it was
changed erroneously in commit 83f0e55 (cpufreq: governors: remove
redundant code).
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initially ondemand governor was written and then using its code conservative
governor is written. It used a lot of code from ondemand governor, but copy of
code was created instead of using the same routines from both governors. Which
increased code redundancy, which is difficult to manage.
This patch is an attempt to move common part of both the governors to
cpufreq_governor.c file to come over above mentioned issues.
This shouldn't change anything from functionality point of view.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Multiple cpufreq governers have defined similar get_cpu_idle_time_***()
routines. These routines must be moved to some common place, so that all
governors can use them.
So moving them to cpufreq_governor.c, which seems to be a better place for
keeping these routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Reevaluate CPU load and update frequency immediately whenever limits
are changed. Currently ondemand doesn't do that when limits are
relaxed, wasting power on systems with relatively low sampling rate.
Signed-off-by: Michal Pecio <mpecio@nvidia.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Initalizers for deferrable delayed_work are confused.
* __DEFERRED_WORK_INITIALIZER()
* DECLARE_DEFERRED_WORK()
* INIT_DELAYED_WORK_DEFERRABLE()
Rename them to
* __DEFERRABLE_WORK_INITIALIZER()
* DECLARE_DEFERRABLE_WORK()
* INIT_DEFERRABLE_WORK()
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
When a new sampling rate is shorter than the current one, (e.g., 1 sec
--> 10 ms) regardless how short the new one is, the current ondemand
mechanism wait for the previously set timer to be expired.
For example, if the user has just expressed that the sampling rate
should be 10 ms from now and the previous was 1000 ms, the new rate may
become effective 999 ms later, which could be not acceptable for the
user if the user has intended to speed up sampling because the system is
expected to react to CPU load fluctuation quickly from __now__.
In order to address this issue, we need to cancel the previously set
timer (schedule_delayed_work) and reset the timer if resetting timer is
expected to trigger the delayed_work ealier.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
[CPUFREQ] EXYNOS: Removed useless headers and codes
[CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
[CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
[CPUFREQ] powernow-k8: Fix indexing issue
[CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
[CPUFREQ] update lpj only if frequency has changed
[CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
[CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
[CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
[CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
[CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
[CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
cpufreq: OMAP: fix freq_table leak
cpufreq: OMAP: put clk if cpu_init failed
cpufreq: OMAP: only supports OPP library
cpufreq: OMAP: dont support !freq_table
cpufreq: OMAP: deny initialization if no mpudev
cpufreq: OMAP: move clk name decision to init
cpufreq: OMAP: notify even with bad boot frequency
...
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CPUFREQ Remove wall variable from cpufreq_gov_dbs_init()
Remove wall variable from cpufreq_gov_dbs_init() as
get_cpu_idle_time_us() no longer updates the last_update_time
unconditionally. Passing non-NULL last_update_time address
will result in accounting additional idle time with
update_ts_time_stats() before returning idle_sleeptime.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
--
drivers/cpufreq/cpufreq_ondemand.c | 3 +--
1 files changed, 1 insertions(+), 2 deletions(-)
This patch changes fields in cpustat from a structure, to an
u64 array. Math gets easier, and the code is more flexible.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Tuner <pjt@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1322498719-2255-2-git-send-email-glommer@parallels.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
update_ts_time_stat currently updates idle time even if we are in
iowait loop at the moment. The only real users of the idle counter
(via get_cpu_idle_time_us) are CPU governors and they expect to get
cumulative time for both idle and iowait times.
The value (idle_sleeptime) is also printed to userspace by print_cpu
but it prints both idle and iowait times so the idle part is misleading.
Let's clean this up and fix update_ts_time_stat to account both counters
properly and update consumers of idle to consider iowait time as well.
If we do this we might use get_cpu_{idle,iowait}_time_us from other
contexts as well and we will get expected values.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/e9c909c221a8da402c4da07e4cd968c3218f8eb1.1314172057.git.mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There cannot be any concurrent access to these through
different cpu sysfs files anymore, because these tunables
are now all global (not per cpu).
I still have some doubts whether some of these locks
were needed at all. Anyway, let's get rid of them.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
Marked deprecated for quite a whilte now...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
Marked deprecated for quite a while now...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
CC: cpufreq@vger.kernel.org
calculate ondemand delay after dbs_check_cpu call because it can
modify rate_mult value
use freq_lo_jiffies value for the sub sample period of powersave_bias mode
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
With cmwq, there's no reason for cpufreq drivers to use separate
workqueues. Remove the dedicated workqueues from cpufreq_conservative
and cpufreq_ondemand and use system_wq instead. The work items are
already sync canceled on stop, so it's already guaranteed that no work
is running on module exit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Adds a new global tunable, sampling_down_factor. Set to 1 it makes no
changes from existing behavior, but set to greater than 1 (e.g. 100)
it acts as a multiplier for the scheduling interval for reevaluating
load when the CPU is at its top speed due to high load. This improves
performance by reducing the overhead of load evaluation and helping
the CPU stay at its top speed when truly busy, rather than shifting
back and forth in speed. This tunable has no effect on behavior at
lower speeds/lower CPU loads.
This patch is against 2.6.36-rc6.
This patch should help solve kernel bug 19672 "ondemand is slow".
Signed-off-by: David Niemi <dniemi@verisign.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
CC: Daniel Hollocher <danielhollocher@gmail.com>
CC: <cpufreq-list@vger.kernel.org>
CC: <linux-kernel@vger.kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
For UP systems this is not required, and results in a more consistent
sample interval.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jocelyn Falempe <jocelyn.falempe@motorola.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Make simpler to read and call.
*** v3 - Always call when powersave_bias is enabled.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hypervisor: add missing <linux/module.h>
Modify the VMware balloon driver for the new x86_hyper API
x86, hypervisor: Export the x86_hyper* symbols
x86: Clean up the hypervisor layer
x86, HyperV: fix up the license to mshyperv.c
x86: Detect running on a Microsoft HyperV system
x86, cpu: Make APERF/MPERF a normal table-driven flag
x86, k8: Fix build error when K8_NB is disabled
x86, cacheinfo: Disable index in all four subcaches
x86, cacheinfo: Make L3 cache info per node
x86, cacheinfo: Reorganize AMD L3 cache structure
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, cacheinfo: Unify AMD L3 cache index disable checking
cpufreq: Unify sysfs attribute definition macros
powernow-k8: Fix frequency reporting
x86, cpufreq: Add APERF/MPERF support for AMD processors
x86: Unify APERF/MPERF support
powernow-k8: Add core performance boost support
x86, cpu: Add AMD core boosting feature flag to /proc/cpuinfo
Fix up trivial conflicts in arch/x86/kernel/cpu/intel_cacheinfo.c and
drivers/cpufreq/cpufreq_ondemand.c
Pavel Machek pointed out that not all CPUs have an efficient
idle at high frequency. Specifically, older Intel and various
AMD cpus would get a higher powerusage when copying files from
USB.
Mike Chan pointed out that the same is true for various ARM
chips as well.
Thomas Renninger suggested to make this a sysfs tunable with a
reasonable default.
This patch adds a sysfs tunable for the new behavior, and uses
a very simple function to determine a reasonable default,
depending on the CPU vendor/type.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082651.46914d04@infradead.org>
[ minor tidyup ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ondemand cpufreq governor uses CPU busy time (e.g. not-idle
time) as a measure for scaling the CPU frequency up or down.
If the CPU is busy, the CPU frequency scales up, if it's idle,
the CPU frequency scales down. Effectively, it uses the CPU busy
time as proxy variable for the more nebulous "how critical is
performance right now" question.
This algorithm falls flat on its face in the light of workloads
where you're alternatingly disk and CPU bound, such as the ever
popular "git grep", but also things like startup of programs and
maildir using email clients... much to the chagarin of Andrew
Morton.
This patch changes the ondemand algorithm to count iowait time
as busy, not idle, time. As shown in the breakdown cases above,
iowait is performance critical often, and by counting iowait,
the proxy variable becomes a more accurate representation of the
"how critical is performance" question.
The problem and fix are both verified with the "perf timechar"
tool.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100509082606.3d9f00d0@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Multiple modules used to define those which are with identical
functionality and were needlessly replicated among the different cpufreq
drivers. Push them into the header and remove duplication.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1270065406-1814-7-git-send-email-bp@amd64.org>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Dominik said:
target_freq cannot be below policy->min or above policy->max.
If it were, the whole cpufreq subsystem is broken.
But (answer):
I think the "ondemand" governor can ask for a target frequency that is
below policy->min.
...
A patch such as below may be needed to sanitize the target frequency
requested by "ondemand". The "conservative" governor already has this check:
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
# diff -bur x/drivers/cpufreq/cpufreq_ondemand.c.orig y/drivers/cpufreq/cpufreq_ondemand.c
ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in
microseconds.
The problem was reported and diagnosed by Alexander here.
http://marc.info/?l=linux-kernel&m=125752550404513&w=2
The patch below fixes this thinko.
Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix NULL ptr regression in powernow-k8
[CPUFREQ] Create a blacklist for processors that should not load the acpi-cpufreq module.
[CPUFREQ] Powernow-k8: Enable more than 2 low P-states
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)
[CPUFREQ] ondemand - Use global sysfs dir for tuning settings
[CPUFREQ] Introduce global, not per core: /sys/devices/system/cpu/cpufreq
[CPUFREQ] Bail out of cpufreq_add_dev if the link for a managed CPU got created
[CPUFREQ] Factor out policy setting from cpufreq_add_dev
[CPUFREQ] Factor out interface creation from cpufreq_add_dev
[CPUFREQ] Factor out symlink creation from cpufreq_add_dev
[CPUFREQ] cleanup up -ENOMEM handling in cpufreq_add_dev
[CPUFREQ] Reduce scope of cpu_sys_dev in cpufreq_add_dev
[CPUFREQ] update Doc for cpuinfo_cur_freq and scaling_cur_freq
Ondemand has only global variables for userspace tunings via sysfs.
But they were exposed per CPU which wrongly implies to the user that
his settings are applied per cpu. Also locking sysfs against concurrent
access won't be necessary anymore after deprecation time.
This means the ondemand config dir is moved:
/sys/devices/system/cpu/cpu*/cpufreq/ondemand ->
/sys/devices/system/cpu/cpufreq/ondemand
The old files will still exist, but reading or writing to them will
result in one (printk_once) deprecation msg to syslog per file.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Redesign the locking inside ondemand driver. Make dbs_mutex handle all the
global state changes inside the driver and invent a new percpu mutex
to serialize percpu timer and frequency limit change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Commit b14893a62c although it was very
much needed to properly cleanup ondemand timer, opened-up a can of worms
related to locking dependencies in cpufreq.
Patch here defines the need for dbs_mutex and cleans up its usage in
ondemand governor. This also resolves the lockdep warnings reported here
http://lkml.indiana.edu/hypermail/linux/kernel/0906.1/01925.htmlhttp://lkml.indiana.edu/hypermail/linux/kernel/0907.0/00820.html
and few others..
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Percpu variable definition is about to be updated such that all percpu
symbols including the static ones must be unique. Update percpu
variable definitions accordingly.
* as,cfq: rename ioc_count uniquely
* cpufreq: rename cpu_dbs_info uniquely
* xen: move nesting_count out of xen_evtchn_do_upcall() and rename it
* mm: move ratelimits out of balance_dirty_pages_ratelimited_nr() and
rename it
* ipv4,6: rename cookie_scratch uniquely
* x86 perf_counter: rename prev_left to pmc_prev_left, irq_entry to
pmc_irq_entry and nmi_entry to pmc_nmi_entry
* perf_counter: rename disable_count to perf_disable_count
* ftrace: rename test_event_disable to ftrace_test_event_disable
* kmemleak: rename test_pointer to kmemleak_test_pointer
* mce: rename next_interval to mce_next_interval
[ Impact: percpu usage cleanups, no duplicate static percpu var names ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: linux-mm <linux-mm@kvack.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Update the documentation accordingly.
Cleanup and use printk_once.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
With this patch you have following minimal sampling rate restrictions:
Kernel restrictions:
If CONFIG_NO_HZ is set, the limit is 10ms fixed.
If CONFIG_NO_HZ is not set or no_hz=off boot parameter is used, the
limits depend on the CONFIG_HZ option:
HZ=1000: min=20000us (20ms)
HZ=250: min=80000us (80ms)
HZ=100: min=200000us (200ms)
HW restrictions:
Do not sample/poll more often than HW latency * 100 exported by the low
level cpufreq HW driver
The higher value of above restrictions is the minimal sampling rate
that can be set (and can be seen via ondemand/sampling_rate_min sysfs file)
Default sampling rate still is HW latency * 1000, but this will now end
up in lower values on latest (Intel and AMD) hardware as these can switch
really fast and sampling rate mostly was limited to the 80ms or 200ms
(depending on whether HZ=250 or HZ=1000 is used).
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Pallipadi Venkatesh <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(updated changelog)
cpufreq fix timer teardown in ondemand governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
The following patch applies to, at least, 2.6.28.x, 2.6.29.1, 2.6.30-rc2.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: gregkh@suse.de
CC: stable@kernel.org
CC: cpufreq@vger.kernel.org
CC: Ingo Molnar <mingo@elte.hu>
CC: rjw@sisk.pl
CC: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Limit sampling rate to transition_latency * 100 or kernel limits.
If sampling_rate is tried to be set too low, set the lowest allowed value.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
The same info can be obtained via the transition_latency sysfs file
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
ondemand micro-accounting of idle time changes broke ignore_nice_load
sysfs setting due to a thinko in the code.
The bug entry:
http://bugzilla.kernel.org/show_bug.cgi?id=12310
Reported-by: Jim Bray <jimsantelmo@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: use new cpumask API to reduce memory usage
This is part of an effort to reduce structure sizes for machines
configured with large NR_CPUS. cpumask_t gets replaced by
cpumask_var_t, which is either struct cpumask[1] (small NR_CPUS) or
struct cpumask * (large NR_CPUS).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We don't need to export the governors for use as the default governor,
because the default governor will be built-in anyway and we can access
the symbol directly.
This also fixes the following sparse warnings:
drivers/cpufreq/cpufreq_conservative.c:578:25: warning: symbol 'cpufreq_gov_conservative' was not declared. Should it be static?
drivers/cpufreq/cpufreq_ondemand.c:582:25: warning: symbol 'cpufreq_gov_ondemand' was not declared. Should it be static?
drivers/cpufreq/cpufreq_performance.c:39:25: warning: symbol 'cpufreq_gov_performance' was not declared. Should it be static?
drivers/cpufreq/cpufreq_powersave.c:38:25: warning: symbol 'cpufreq_gov_powersave' was not declared. Should it be static?
drivers/cpufreq/cpufreq_userspace.c:190:25: warning: symbol 'cpufreq_gov_userspace' was not declared. Should it be static?
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Use get_cpu_idle_time_us() to get micro-accounted idle information.
This enables ondemand to get more accurate idle and busy timings
than the jiffy based calculation. As a result, we can decrease
the ondemand safety gaurd band from 80-10 to 95-3.
Results in more aggressive power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Use a parameter for down differential, instead of hardcoded 10%. Follow-on
patch changes the down-differential dynamically, based on whether
we are using idle micro-accounting or not.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Preparatory changes for doing idle micro-accounting in ondemand governor.
get_cpu_idle_time() gets extra parameter and returns idle time and also the
wall time that corresponds to the idle time measurement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Change the load calculation algorithm in ondemand to work well with software
coordination of frequency across the dependent cpus.
Multiply individual CPU utilization with the average freq of that logical CPU
during the measurement interval (using getavg call). And find the max CPU
utilization number in terms of CPU freq. That number is then used to
get to the target freq for next sampling interval.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add a cpu parameter to __cpufreq_driver_getavg(). This is needed for software
cpufreq coordination where policy->cpu may not be same as the CPU on which we
want to getavg frequency.
A follow-on patch will use this parameter to getavg freq from all cpus
in policy->cpus.
Change since last patch. Fix the offline/online and suspend/resume
oops reported by Youquan Song <youquan.song@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add error handling for cpufreq_register_governor() error
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Dave Jones <davej@redhat.com>
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the cpufreq driver starts up at boot time, it calls into the default
governor which might not be initialised yet. This hurts when the
governor's worker function relies on memory that is not yet set up by its
init function.
This migrates all governors from module_init() to fs_initcall() when being
the default, as was already done in cpufreq_performance when it was the
only possible choice. The performance governor is always initialized early
because it might be used as fallback even when not being the default.
Fixes at least one actual oops where ondemand is the default governor and
cpufreq_governor_dbs() uses the uninitialised kondemand_wq work-queue
during boot-time.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on the transition latency of the HW for cpufreq switches, the
ondemand or conservative governor cannot be used with certain cpufreq
drivers. Still the ondemand should be the default governor on a wide range
of systems. This patch allows this and lets the governor fallback to the
performance governor at cpufreq driver load time, if the driver does not
support fast enough frequency switching.
Main benefit is that on e.g. installation or other systems without
userspace support a working dynamic cpufreq support can be achieved on most
systems by simply loading the cpufreq driver. This is especially essential
for recent x86(_64) laptop hardware which may rely on working dynamic
cpufreq OS support.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
With tickless kernel and software coordination os P-states, ondemand
can look at wrong idle statistics. This can happen when ondemand sampling
is happening on CPU 0 and due to software coordination sampling also looks at
utilization of CPU 1. If CPU 1 is in tickless state at that moment, its idle
statistics will not be uptodate and CPU 0 thinks CPU 1 is idle for less
amount of time than it actually is.
This can be resolved by looking at all the busy times of CPUs, which is
accurate, even with tickless, and use that to determine idle time in a
round about way (total time - busy time).
Thanks to Arjan for originally reporting the ondemand bug on
Lenovo T61.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Due to rounding and inexact jiffy accounting, idle_ticks can sometimes
be higher than total_ticks. Make sure those cases are handled as
zero load case.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add a new deferrable delayed work init. This can be used to schedule work
that are 'unimportant' when CPU is idle and can be called later, when CPU
eventually comes out of idle.
Use this init in cpufreq ondemand governor.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Looks like dbs_timer() is very careful wrt per_cpu(cpu_dbs_info),
and it doesn't need the help of WORK_STRUCT_NOAUTOREL.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Eliminate flush_workqueue in cpufreq_governor(STOP) callpath. Using flush
there has a deadlock potential as in
http://uwsg.iu.edu/hypermail/linux/kernel/0611.3/1223.html
Also, cleanup the locking issues with do_dbs_timer delayed_work callback. As
it changes the CPU frequency using __cpufreq_target, it needs to have
policy_rwsem in write mode, which also protects it from hot plug.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Restructure the delayed_work callback in ondemand.
This eliminates the need for smp_processor_id in the callback function and
also helps in proper locking and avoiding flush_workqueue when stopping the
governor (done in subsequent patch).
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The hotplug CPU locking in cpufreq is horrendous. No-one seems to care
enough to fix it, so just remove it so that the 99.9% of the real world
users of this code can use cpufreq without being bothered by warnings.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Clean up cpufreq subsystem to fix coding style issues and to improve
the readability.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Enable ondemand governor and acpi-cpufreq to use IA32_APERF and IA32_MPERF MSR
to get active frequency feedback for the last sampling interval. This will
make ondemand take right frequency decisions when hardware coordination of
frequency is going on.
Without APERF/MPERF, ondemand can take wrong decision at times due
to underlying hardware coordination or TM2.
Example:
* CPU 0 and CPU 1 are hardware cooridnated.
* CPU 1 running at highest frequency.
* CPU 0 was running at highest freq. Now ondemand reduces it to
some intermediate frequency based on utilization.
* Due to underlying hardware coordination with other CPU 1, CPU 0 continues to
run at highest frequency (as long as other CPU is at highest).
* When ondemand samples CPU 0 again next time, without actual frequency
feedback from APERF/MPERF, it will think that previous frequency change
was successful and can go to wrong target frequency. This is because it
thinks that utilization it has got this sampling interval is when running at
intermediate frequency, rather than actual highest frequency.
More information about IA32_APERF IA32_MPERF MSR:
Refer to IA-32 Intel® Architecture Software Developer's Manual at
http://developer.intel.com
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch makes the needlessly global powersave_bias_target() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
ondemand selects the minimum frequency that can retire
a workload with negligible idle time -- ideally resulting in the highest
performance/power efficiency with negligible performance impact.
But on some systems and some workloads, this algorithm
is more performance biased than necessary, and
de-tuning it a bit to allow some performance impact
can save measurable power.
This patch adds a "powersave_bias" tunable to ondemand
to allow it to reduce its target frequency by a specified percent.
By default, the powersave_bias is 0 and has no effect.
powersave_bias is in units of 0.1%, so it has an effective range
of 1 through 1000, resulting in 0.1% to 100% impact.
In practice, users will not be able to detect a difference between
0.1% increments, but 1.0% increments turned out to be too large.
Also, the max value of 1000 (100%) would simply peg the system
in its deepest power saving P-state, unless the processor really has
a hardware P-state at 0Hz:-)
For example, If ondemand requests 2.0GHz based on utilization,
and powersave_bias=100, this code will knock 10% off the target
and seek a target of 1.8GHz instead of 2.0GHz until the
next sampling. If 1.8 is an exact match with an hardware frequency
we use it, otherwise we average our time between the frequency
next higher than 1.8 and next lower than 1.8.
Note that a user or administrative program can change powersave_bias
at run-time depending on how they expect the system to be used.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi at intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy at intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Try to make dbs_check_cpu() call on all CPUs at the same jiffy.
This will help when multiple cores share P-states via Hardware Coordination.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi at intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy at intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.
The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
__cpufreq_driver_target
__cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
__cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
__cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
the lock_cpu_hotplug() lock.
I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.
The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)
The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Shutting down the ondemand policy was fraught with potential
problems, causing issues for SMP suspend (which wants to hot-
unplug) all but the last CPU.
This should fix at least the worst problems (divide-by-zero
and infinite wait for the workqueue to shut down).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Misc cleanups in ondemand. Should have zero functional impact.
Also adding Alexey as author.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Viresh Kumar