This patch drops the current way of 6lowpan fragmentation on receiving
side and replace it with a implementation which use the inet_frag api.
The old fragmentation handling has some race conditions and isn't
rfc4944 compatible. Also adding support to match fragments on
destination address, source address, tag value and datagram_size
which is missing in the current implementation.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detected with:
./scripts/checkpatch.pl --strict -f net/ieee802154/6lowpan_rtnl.c
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a 6lowpan.c file and 6lowpan.ko file. To avoid confusing we
should move 6lowpan.c to 6lowpan_rtnl.c. Then we can support multiple
source files for 6lowpan module.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the fragmentation on sending side according to rfc4944.
Also add improvement to use the full payload of a PDU which calculate
the nearest divided to 8 payload length for the fragmentation datagram
size attribute.
The main issue is that the datagram size of fragmentation header use the
ipv6 payload length, but rfc4944 says it's the ipv6 payload length inclusive
network header size (and transport header size if compressed).
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a lookup function for uncompressed 6LoWPAN header
size. This is needed to estimate the real size after uncompress the
6LoWPAN header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 57f89bfa21 ("network: Allow af_packet to transmit +4 bytes
for VLAN packets.") added the possibility for non-mmaped frames to
send extra 4 byte for VLAN header so the MTU increases from 1500 to
1504 byte, for example.
Commit cbd89acb9e ("af_packet: fix for sending VLAN frames via
packet_mmap") attempted to fix that for the mmap part but was
reverted as it caused regressions while using eth_type_trans()
on output path.
Lets just act analogous to 57f89bfa21 and add a similar logic
to TX_RING. We presume size_max as overcharged with +4 bytes and
later on after skb has been built by tpacket_fill_skb() check
for ETH_P_8021Q header on packets larger than normal MTU. Can
be easily reproduced with a slightly modified trafgen in mmap(2)
mode, test cases:
{ fill(0xff, 12) const16(0x8100) fill(0xff, <1504|1505>) }
{ fill(0xff, 12) const16(0x0806) fill(0xff, <1500|1501>) }
Note that we need to do the test right after tpacket_fill_skb()
as sockets can have PACKET_LOSS set where we would not fail but
instead just continue to traverse the ring.
Reported-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Phil Sutter <phil@nwl.cc>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 9195bb8e38 ("ipv6: improve
ipv6_find_hdr() to skip empty routing headers") broke ipv6_find_hdr().
When a target is specified like IPPROTO_ICMPV6 ipv6_find_hdr()
returns -ENOENT when it's found, not the header as expected.
A part of IPVS is broken and possible also nft_exthdr_eval().
When target is -1 which it is most cases, it works.
This patch exits the do while loop if the specific header is found
so the nexthdr could be returned as expected.
Reported-by: Art -kwaak- van Breemen <ard@telegraafnet.nl>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
CC:Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the neigh table's entries is less than gc_thresh1, the function
will return directly, and the reachabletime will not be recompute,
so the reachabletime can be guessed.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Regarding the mac80211 bits, Johannes says:
"This time, I have a fix from Arik for scheduled scan recovery (something
that only recently went into the tree), a memory leak fix from Eytan and
a small regulatory bugfix from Inbal. The EAPOL change from Felix makes
rekeying more stable while lots of traffic is flowing, and there's
Emmanuel's and my fixes for a race in the code handling powersaving
clients."
Regarding the NFC bits, Samuel says:
"We only have one candidate for 3.14 fixes, and this is a NCI NULL
pointer dereference introduced during the 3.14 merge window."
Regarding the iwlwifi bits, Emmanuel says:
"This should fix an issue raised in iwldvm when we have lots of
association failures. There is a bugzilla for this bug - it hasn't
been validated by the user, but I hope it will do the trick."
Beyond that...
Amitkumar Karwar brings two mwifiex fixes, one to avoid a NULL pointer
dereference and another to address an improperly timed interrupt.
Arend van Spriel gives us a brcmfmac fix to avoid a crash during
scatter-gather packet transfers.
Avinash Patila offers an mwifiex to avoid an invalid memory access
when a device is removed.
Bing Zhao delivers a simple fix to avoid a naming conflict between
libertas and mwifiex.
Felix Fietkau provides a trio of ath9k fixes that properly account
for sequence numbering in ps-poll frames, reduce the rate for false
positives during baseband hang detection, and fix a regression related
to rx descriptor handling.
James Cameron shows us a libertas fix to ignore zero-length IEs when
processing scan results.
Kirill Tkhai brings a hostap fix to avoid prematurely freeing a timer.
Stanislaw Gruszka fixes an ath9k locking problem.
Sujith Manoharan addresses ETSI compliance for a device handled by
ath9k by adjusting the minimum CCA power threshold values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Because those following if conditions will not be matched.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
This is the rework of the IPsec virtual tunnel interface
for ipv4 to support inter address family tunneling and
namespace crossing. The only change to the last RFC version
is a compile fix for an odd configuration where CONFIG_XFRM
is set but CONFIG_INET is not set.
1) Add and use a IPsec protocol multiplexer.
2) Add xfrm_tunnel_skb_cb to the skb common buffer
to store a receive callback there.
3) Make vti work with i_key set by not including the i_key
when comupting the hash for the tunnel lookup in case of
vti tunnels.
4) Update ip_vti to use it's own receive hook.
5) Remove xfrm_tunnel_notifier, this is replaced by the IPsec
protocol multiplexer.
6) We need to be protocol family indepenent, so use the on xfrm_lookup
returned dst_entry instead of the ipv4 rtable in vti_tunnel_xmit().
7) Add support for inter address family tunneling.
8) Check if the tunnel endpoints of the xfrm state and the vti interface
are matching and return an error otherwise.
8) Enable namespace crossing tor vti devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Build fix for ip_vti when NET_IP_TUNNEL is not set.
We need this set to have ip_tunnel_get_stats64()
available.
2) Fix a NULL pointer dereference on sub policy usage.
We try to access a xfrm_state from the wrong array.
3) Take xfrm_state_lock in xfrm_migrate_state_find(),
we need it to traverse through the state lists.
4) Clone states properly on migration, otherwise we crash
when we migrate a state with aead algorithm attached.
5) Fix unlink race when between thread context and timer
when policies are deleted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VHT network uses 20 or 40 MHz as per the HT operation
information, the channel center frequency segment 0 field in
the VHT operation information is reserved, so ignore it.
This fixes association with such networks when the AP puts 0
into the field, previously we'd disconnect due to an invalid
channel with the message
wlan0: AP VHT information is invalid, disable VHT
Cc: stable@vger.kernel.org
Fixes: f2d9d270c1 ("mac80211: support VHT association")
Reported-by: Tim Nelson <tim.l.nelson@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The allocated child qdisc is not freed in error conditions.
Defer the allocation after user configuration turns out to be
valid and acceptable.
Fixes: cc106e441a ("net: sched: tbf: fix the calculation of max_size")
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming congestion controls for TCP require usec resolution for RTT
estimations. Millisecond resolution is simply not enough these days.
FQ/pacing in DC environments also require this change for finer control
and removal of bimodal behavior due to the current hack in
tcp_update_pacing_rate() for 'small rtt'
TCP_CONG_RTT_STAMP is no longer needed.
As Julian Anastasov pointed out, we need to keep user compatibility :
tcp_metrics used to export RTT and RTTVAR in msec resolution,
so we added RTT_US and RTTVAR_US. An iproute2 patch is needed
to use the new attributes if provided by the kernel.
In this example ss command displays a srtt of 32 usecs (10Gbit link)
lpk51:~# ./ss -i dst lpk52
Netid State Recv-Q Send-Q Local Address:Port Peer
Address:Port
tcp ESTAB 0 1 10.246.11.51:42959
10.246.11.52:64614
cubic wscale:6,6 rto:201 rtt:0.032/0.001 ato:40 mss:1448
cwnd:10 send
3620.0Mbps pacing_rate 7240.0Mbps unacked:1 rcv_rtt:993 rcv_space:29559
Updated iproute2 ip command displays :
lpk51:~# ./ip tcp_metrics | grep 10.246.11.52
10.246.11.52 age 561.914sec cwnd 10 rtt 274us rttvar 213us source
10.246.11.51
Old binary displays :
lpk51:~# ip tcp_metrics | grep 10.246.11.52
10.246.11.52 age 561.914sec cwnd 10 rtt 250us rttvar 125us source
10.246.11.51
With help from Julian Anastasov, Stephen Hemminger and Yuchung Cheng
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Larry Brakmo <brakmo@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option has the same semantic as IP_PMTUDISC_OMIT for IPv4 which
got recently introduced. It doesn't honor the path mtu discovered by the
host but in contrary to IPV6_PMTUDISC_INTERFACE allows the generation of
fragments if the packet size exceeds the MTU of the outgoing interface
MTU.
Fixes: 93b36cf342 ("ipv6: support IPV6_PMTU_INTERFACE on sockets")
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP_PMTUDISC_INTERFACE has a design error: because it does not allow the
generation of fragments if the interface mtu is exceeded, it is very
hard to make use of this option in already deployed name server software
for which I introduced this option.
This patch adds yet another new IP_MTU_DISCOVER option to not honor any
path mtu information and not accepting new icmp notifications destined for
the socket this option is enabled on. But we allow outgoing fragmentation
in case the packet size exceeds the outgoing interface mtu.
As such this new option can be used as a drop-in replacement for
IP_PMTUDISC_DONT, which is currently in use by most name server software
making the adoption of this option very smooth and easy.
The original advantage of IP_PMTUDISC_INTERFACE is still maintained:
ignoring incoming path MTU updates and not honoring discovered path MTUs
in the output path.
Fixes: 482fc6094a ("ipv4: introduce new IP_MTU_DISCOVER mode IP_PMTUDISC_INTERFACE")
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_skb_dst_mtu mostly falls back to ip_dst_mtu_maybe_forward if no socket
is attached to the skb (in case of forwarding) or determines the mtu like
we do in ip_finish_output, which actually checks if we should branch to
ip_fragment. Thus use the same function to determine the mtu here, too.
This is important for the introduction of IP_PMTUDISC_OMIT, where we
want the packets getting cut in pieces of the size of the outgoing
interface mtu. IPv6 already does this correctly.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
iproute2 arpd seems to expect this as there's code and comments
to handle netlink probes with NUD_PROBE set. It is used to flush
the arpd cached mappings.
opennhrp instead turns off unicast probes (so it can handle all
neighbour discovery). Without this change it will not see NUD_PROBE
probes and cannot reconfirm the mapping. Thus currently neigh entry
will just fail and can cause few packets dropped until broadcast
discovery is restarted.
Earlier discussion on the subject:
http://marc.info/?t=139305877100001&r=1&w=2
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These info messages are rather pointless without any means to identify
the source of the bogus packets. Logging the src and dst addresses and
ports may help a bit.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysfs file to enable user space to query the device
port number used by a netdevice instance. This is needed for
devices that have multiple ports on the same PCI function.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three counters are added:
- one to track when we went from non-zero to zero window
- one to track the reverse
- one counter incremented when we want to announce zero window,
but can't because we would shrink current window.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While LINUX_MIB_TCPSPURIOUS_RTX_HOSTQUEUES can only be incremented
in tcp_transmit_skb() from softirq (incoming message or timer
activation), it is better to use NET_INC_STATS() instead of
NET_INC_STATS_BH() as tcp_transmit_skb() can be called from process
context.
This will avoid copy/paste confusion when/if we want to add
other SNMP counters in tcp_transmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the RxRPC header flag to request an ACK packet for every odd-numbered DATA
packet unless it's the last one (which implicitly requests an ACK anyway).
This is similar to how librx appears to work.
If we don't do this, we'll send out a full window of packets and then just sit
there until the other side gets bored and sends an ACK to indicate that it's
been idle for a while and has received no new packets.
Requesting a lot of ACKs shouldn't be a problem as ACKs should be merged when
possible.
As AF_RXRPC currently works, it will schedule an ACK to be generated upon
receipt of a DATA packet with the ACK-request packet set - and in the time
taken to schedule this in a work queue, several other packets are likely to
arrive and then all get ACK'd together.
Signed-off-by: David Howells <dhowells@redhat.com>
Expose RxRPC parameters via sysctls to control the Rx window size, the Rx MTU
maximum size and the number of packets that can be glued into a jumbo packet.
More info added to Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
Improve ACK production by the following means:
(1) Don't send an ACK_REQUESTED ack immediately even if the RXRPC_MORE_PACKETS
flag isn't set on a data packet that has also has RXRPC_REQUEST_ACK set.
MORE_PACKETS just means that the sender just emptied its Tx data buffer.
More data will be forthcoming unless RXRPC_LAST_PACKET is also flagged.
It is possible to see runs of DATA packets with MORE_PACKETS unset that
aren't waiting for an ACK.
It is therefore better to wait a small instant to see if we can combine an
ACK for several packets.
(2) Don't send an ACK_IDLE ack immediately unless we're responding to the
terminal data packet of a call.
Whilst sending an ACK_IDLE mid-call serves to let the other side know
that we won't be asking it to resend certain Tx buffers and that it can
discard them, spamming it with loads of acks just because we've
temporarily run out of data just distracts it.
(3) Put the ACK_IDLE ack generation timeout up to half a second rather than a
single jiffy. Just because we haven't been given more data immediately
doesn't mean that more isn't forthcoming. The other side may be busily
finding the data to send to us.
Signed-off-by: David Howells <dhowells@redhat.com>
Add sysctls for configuring RxRPC protocol handling, specifically controls on
delays before ack generation, the delay before resending a packet, the maximum
lifetime of a call and the expiration times of calls, connections and
transports that haven't been recently used.
More info added in Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
AF_RXRPC sends UDP packets with the "Don't Fragment" bit set in an attempt to
determine the maximum packet size between the local socket and the peer by
invoking the generation of ICMP_FRAG_NEEDED packets.
Once a packet is sent with the "Don't Fragment" bit set, it is then
inconvenient to break it up as that requires recalculating all the rxrpc serial
and sequence numbers and reencrypting all the fragments, so we switch off the
"Don't Fragment" service temporarily and send the bounced packet again. Future
packets then use the new MTU.
That's all fine. The problem lies in rxrpc_UDP_error_report() where the code
that deals with ICMP_FRAG_NEEDED packets lives. Packets of this type have a
field (ee_info) to indicate the maximum packet size at the reporting node - but
sometimes ee_info isn't filled in and is just left as 0 and the code must allow
for this.
When ee_info is 0, the code should take the MTU size we're currently using and
reduce it for the next packet we want to send. However, it takes ee_info
(which is known to be 0) and tries to reduce that instead.
This was discovered by Coverity.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
When a policy is unlinked from the lists in thread context,
the xfrm timer can fire before we can mark this policy as dead.
So reinitialize the bydst hlist, then hlist_unhashed() will
notice that this policy is not linked and will avoid a
doulble unlink of that policy.
Reported-by: Xianpeng Zhao <673321875@qq.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
netlink_sendmsg() was changed to prevent non-root processes from sending
messages with dst_pid != 0.
netlink_connect() however still only checks if nladdr->nl_groups is set.
This patch modifies netlink_connect() to check for the same condition.
Signed-off-by: Mike Pecovnik <mike.pecovnik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UFO fragmentation process does not correctly handle inner
UDP frames.
(The following tcpdumps are captured on the parent interface with ufo
disabled while tunnel has ufo enabled, 2000 bytes payload, mtu 1280,
both sit device):
IPv6:
16:39:10.031613 IP (tos 0x0, ttl 64, id 3208, offset 0, flags [DF], proto IPv6 (41), length 1300)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 1240) 2001::1 > 2001::8: frag (0x00000001:0|1232) 44883 > distinct: UDP, length 2000
16:39:10.031709 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPv6 (41), length 844)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 784) 2001::1 > 2001::8: frag (0x00000001:0|776) 58979 > 46366: UDP, length 5471
We can see that fragmentation header offset is not correctly updated.
(fragmentation id handling is corrected by 916e4cf46d ("ipv6: reuse
ip6_frag_id from ip6_ufo_append_data")).
IPv4:
16:39:57.737761 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPIP (4), length 1296)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57034, offset 0, flags [none], proto UDP (17), length 1276)
192.168.99.1.35961 > 192.168.99.2.distinct: UDP, length 2000
16:39:57.738028 IP (tos 0x0, ttl 64, id 3210, offset 0, flags [DF], proto IPIP (4), length 792)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57035, offset 0, flags [none], proto UDP (17), length 772)
192.168.99.1.13531 > 192.168.99.2.20653: UDP, length 51109
In this case fragmentation id is incremented and offset is not updated.
First, I aligned inet_gso_segment and ipv6_gso_segment:
* align naming of flags
* ipv6_gso_segment: setting skb->encapsulation is unnecessary, as we
always ensure that the state of this flag is left untouched when
returning from upper gso segmenation function
* ipv6_gso_segment: move skb_reset_inner_headers below updating the
fragmentation header data, we don't care for updating fragmentation
header data
* remove currently unneeded comment indicating skb->encapsulation might
get changed by upper gso_segment callback (gre and udp-tunnel reset
encapsulation after segmentation on each fragment)
If we encounter an IPIP or SIT gso skb we now check for the protocol ==
IPPROTO_UDP and that we at least have already traversed another ip(6)
protocol header.
The reason why we have to special case GSO_IPIP and GSO_SIT is that
we reset skb->encapsulation to 0 while skb_mac_gso_segment the inner
protocol of GSO_UDP_TUNNEL or GSO_GRE packets.
Reported-by: Wolfgang Walter <linux@stwm.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset regdomain to world regdomain in case
of errors in set_regdom() function.
This will fix a problem with such scenario:
- iw reg set US
- iw reg set 00
- iw reg set US
The last step always fail and we get deadlock
in kernel regulatory code. Next setting new
regulatory wasn't possible due to:
Pending regulatory request, waiting for it to be processed...
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The tunnel endpoints of the xfrm_state we got from the xfrm_lookup
must match the tunnel endpoints of the vti interface. This patch
ensures this matching.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With this patch we can tunnel ipv6 traffic via a vti4
interface. A vti4 interface can now have an ipv6 address
and ipv6 traffic can be routed via a vti4 interface.
The resulting traffic is xfrm transformed and tunneled
throuhg ipv4 if matching IPsec policies and states are
present.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need to be protocol family indepenent to support
inter addresss family tunneling with vti. So use a
dst_entry instead of the ipv4 rtable in vti_tunnel_xmit.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This was used from vti and is replaced by the IPsec protocol
multiplexer hooks. It is now unused, so remove it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With this patch, vti uses the IPsec protocol multiplexer to
register it's own receive side hooks for ESP, AH and IPCOMP.
Vti now does the following on receive side:
1. Do an input policy check for the IPsec packet we received.
This is required because this packet could be already
prosecces by IPsec, so an inbuond policy check is needed.
2. Mark the packet with the i_key. The policy and the state
must match this key now. Policy and state belong to the outer
namespace and policy enforcement is done at the further layers.
3. Call the generic xfrm layer to do decryption and decapsulation.
4. Wait for a callback from the xfrm layer to properly clean the
skb to not leak informations on namespace and to update the
device statistics.
On transmit side:
1. Mark the packet with the o_key. The policy and the state
must match this key now.
2. Do a xfrm_lookup on the original packet with the mark applied.
3. Check if we got an IPsec route.
4. Clean the skb to not leak informations on namespace
transitions.
5. Attach the dst_enty we got from the xfrm_lookup to the skb.
6. Call dst_output to do the IPsec processing.
7. Do the device statistics.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Vti uses the o_key to mark packets that were transmitted or received
by a vti interface. Unfortunately we can't apply different marks
to in and outbound packets with only one key availabe. Vti interfaces
typically use wildcard selectors for vti IPsec policies. On forwarding,
the same output policy will match for both directions. This generates
a loop between the IPsec gateways until the ttl of the packet is
exceeded.
The gre i_key/o_key are usually there to find the right gre tunnel
during a lookup. When vti uses the i_key to mark packets, the tunnel
lookup does not work any more because vti does not use the gre keys
as a hash key for the lookup.
This patch workarounds this my not including the i_key when comupting
the hash for the tunnel lookup in case of vti tunnels.
With this we have separate keys available for the transmitting and
receiving side of the vti interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPsec vti_rcv needs to remind the tunnel pointer to
check it later at the vti_rcv_cb callback. So add
this pointer to the IPsec common buffer, initialize
it and check it to avoid transport state matching of
a tunneled packet.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch add an IPsec protocol multiplexer. With this
it is possible to add alternative protocol handlers as
needed for IPsec virtual tunnel interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Convert the uses of memcpy to ether_addr_copy because
for some architectures it is smaller and faster.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the more obvious uses of memcpy to ether_addr_copy.
There are still uses of memcpy that could be converted but
these addresses are __aligned(2).
Convert a couple uses of 6 in gr_private.h to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_is_cwnd_limited() allows GSO/TSO enabled flows to increase
their cwnd to allow a full size (64KB) TSO packet to be sent.
Non GSO flows only allow an extra room of 3 MSS.
For most flows with a BDP below 10 MSS, this results in a bloat
of cwnd reaching 90, and an inflate of RTT.
Thanks to TSO auto sizing, we can restrict the bloat to the number
of MSS contained in a TSO packet (tp->xmit_size_goal_segs), to keep
original intent without performance impact.
Because we keep cwnd small, it helps to keep TSO packet size to their
optimal value.
Example for a 10Mbit flow, with low TCP Small queue limits (no more than
2 skb in qdisc/device tx ring)
Before patch :
lpk51:~# ./ss -i dst lpk52:44862 | grep cwnd
cubic wscale:6,6 rto:215 rtt:15.875/2.5 mss:1448 cwnd:96
ssthresh:96
send 70.1Mbps unacked:14 rcv_space:29200
After patch :
lpk51:~# ./ss -i dst lpk52:52916 | grep cwnd
cubic wscale:6,6 rto:206 rtt:5.206/0.036 mss:1448 cwnd:15
ssthresh:14
send 33.4Mbps unacked:4 rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Van Jacobson <vanj@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation misses a few of the supported flags. Fix this. Also
respect the dependency to CONFIG_XFRM for the IPSEC flag.
Cc: Fan Du <fan.du@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'out' label is just a relict from previous times as pgctrl_write()
had multiple error paths. Get rid of it and simply return right away
on errors.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a privileged user writes an empty string to /proc/net/pktgen/pgctrl
the code for stripping the (then non-existent) '\n' actually writes the
zero byte at index -1 of data[]. The then still uninitialized array will
very likely fail the command matching tests and the pr_warning() at the
end will therefore leak stack bytes to the kernel log.
Fix those issues by simply ensuring we're passed a non-empty string as
the user API apparently expects a trailing '\n' for all commands.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MLME code in mac80211 must track whether or not the AP changed
bandwidth, but if there's no change while tracking it shouldn't do
anything, otherwise regulatory updates can make it impossible to
connect to certain APs if the regulatory database doesn't match the
information from the AP. See the precise scenario described in the
code.
This still leaves some possible problems with CSA or if the AP
actually changed bandwidth, but those cases are less common and
won't completely prevent using it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70881
Cc: stable@vger.kernel.org
Reported-and-tested-by: Nate Carlson <kernel@natecarlson.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check should be for setup function pointer.
This patch fixes NULL pointer dereference issue for NCI
based NFC driver which doesn't define setup handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently we generate a new fragmentation id on UFO segmentation. It
is pretty hairy to identify the correct net namespace and dst there.
Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst
available at all.
This causes unreliable or very predictable ipv6 fragmentation id
generation while segmentation.
Luckily we already have pregenerated the ip6_frag_id in
ip6_ufo_append_data and can use it here.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.
Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.
RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:
Some of the transport addresses of a multi-homed SCTP endpoint
may become inactive due to either the occurrence of certain
error conditions (see Section 8.2) or adjustments from the
SCTP user.
When there is outbound data to send and the primary path
becomes inactive (e.g., due to failures), or where the SCTP
user explicitly requests to send data to an inactive
destination transport address, before reporting an error to
its ULP, the SCTP endpoint should try to send the data to an
alternate __active__ destination transport address if one
exists.
When retransmitting data that timed out, if the endpoint is
multihomed, it should consider each source-destination address
pair in its retransmission selection policy. When retransmitting
timed-out data, the endpoint should attempt to pick the most
divergent source-destination pair from the original
source-destination pair to which the packet was transmitted.
Note: Rules for picking the most divergent source-destination
pair are an implementation decision and are not specified
within this document.
So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.
Commit 4141ddc02a ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc02a, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.
Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.
This patch mostly reverts 4141ddc02a, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.
Fixes: 4141ddc02a ("sctp: retran_path update bug fix")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <yasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes bug introduced by:
commit 1d4c8c2984
"neigh: restore old behaviour of default parms values"
The thing is that in neigh_sysctl_register, extra1 and extra2 which were
previously set for NEIGH_VAR_GC_* are overwritten. That leads to
nonsense int limits for gc_* variables. So fix this by not touching
extra* fields for gc_* variables.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two bugs in fastopen :
1) The tcp_sendmsg(..., @size) argument was ignored.
Code was relying on user not fooling the kernel with iovec mismatches
2) When MTU is about 64KB, tcp_send_syn_data() attempts order-5
allocations, which are likely to fail when memory gets fragmented.
Fixes: 783237e8da ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Tested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accidentally a side effect is involved by commit 6e967adf7(tipc:
relocate common functions from media to bearer). Now tipc stack
handler of receiving packets from netdevices as well as netdevice
notification handler are registered when bearer is enabled rather
than tipc module initialization stage, but the two handlers are
both unregistered in tipc module exit phase. If tipc module is
inserted and then immediately removed, the following warning
message will appear:
"dev_remove_pack: ffffffffa0380940 not found"
This is because in module insertion stage tipc stack packet handler
is not registered at all, but in module exit phase dev_remove_pack()
needs to remove it. Of course, dev_remove_pack() cannot find tipc
protocol handler from the kernel protocol handler list so that the
warning message is printed out.
But if registering the two handlers is adjusted from enabling bearer
phase into inserting module stage, the warning message will be
eliminated. Due to this change, tipc_core_start_net() and
tipc_core_stop_net() can be deleted as well.
Reported-by: Wang Weidong <wangweidong1@huawei.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.
But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error pointer passed to xfrm_state_clone() is unchecked,
so remove it and indicate an error by returning a null pointer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch fixes commit d3623099d3 ("ipsec: add support of limited SA dump").
sadb_ext_min_len array should be updated with the new type (SADB_X_EXT_FILTER).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In current implementation it is possible to reach PF state from unconfirmed.
We can interpret sctp-failover-02 in a way that PF state is meant to be reached
only from active state, in the end, this is when entering PF state makes sense.
Here are few quotes from sctp-failover-02, but regardless of these, same
understanding can be reached from whole section 5:
Section 5.1, quickfailover guide:
"The PF state is an intermediate state between Active and Failed states."
"Each time the T3-rtx timer expires on an active or idle
destination, the error counter of that destination address will
be incremented. When the value in the error counter exceeds
PFMR, the endpoint should mark the destination transport address as PF."
There are several concrete reasons for such interpretation. For start, rfc4960
does not take into concern quickfailover algorithm. Therefore, quickfailover
must comply to 4960. Point where this compliance can be argued is following
behavior:
When PF is entered, association overall error counter is incremented for each
missed HB. This is contradictory to rfc4960, as address, while in unconfirmed
state, is subjected to probing, and while it is probed, it should not increment
association overall error counter. This has as a consequence that we might end
up in situation in which we drop association due path failure on unconfirmed
address, in case we have wrong configuration in a way:
Association.Max.Retrans == Path.Max.Retrans.
Another reason is that entering PF from unconfirmed will cause a loss of address
confirmed event when address is once (if) confirmed. This is fine from failover
guide point of view, but it is not consistent with behavior preceding failover
implementation and recommendation from 4960:
5.4. Path Verification
Whenever a path is confirmed, an indication MAY be given to the upper
layer.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug introduced by commit 7d442fab0a ("ipv4: Cache dst in tunnels").
Because sit code does not call ip_tunnel_init(), the dst_cache was not
initialized.
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We loose a lot of information of the original state if we
clone it with xfrm_state_clone(). In particular, there is
no crypto algorithm attached if the original state uses
an aead algorithm. This patch add the missing information
to the clone state.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
A comment on xfrm_migrate_state_find() says that xfrm_state_lock
is held. This is apparently not the case, but we need it to
traverse through the state lists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_state_sort() takes the unsorted states from the src array
and stores them into the dst array. We try to get the namespace
from the dst array which is empty at this time, so take the
namespace from the src array instead.
Fixes: 283bc9f35b ("xfrm: Namespacify xfrm state/policy locks")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since commit 469bdcefdc ip6_vti uses ip_tunnel_get_stats64(),
so we need to select NET_IP_TUNNEL to have this function available.
Fixes: 469bdcefdc ("ipv6: fix the use of pcpu_tstats in ip6_vti.c")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Consider the following (relatively unlikely) scenario:
1) station goes to sleep while frames are buffered in driver
2) driver blocks wakeup (until no more frames are buffered)
3) station wakes up again
4) driver unblocks wakeup
In this case, the current mac80211 code will do the following:
1) WLAN_STA_PS_STA set
2) WLAN_STA_PS_DRIVER set
3) - nothing -
4) WLAN_STA_PS_DRIVER cleared
As a result, no frames will be delivered to the client, even
though it is awake, until it sends another frame to us that
triggers ieee80211_sta_ps_deliver_wakeup() in sta_ps_end().
Since we now take the PS spinlock, we can fix this while at
the same time removing the complexity with the pending skb
queue function. This was broken since my commit 50a9432dae
("mac80211: fix powersaving clients races") due to removing
the clearing of WLAN_STA_PS_STA in the RX path.
While at it, fix a cleanup path issue when a station is
removed while the driver is still blocking its wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a race condition in mac80211 because we add stations
to the internal lists after adding them to the driver, which
means that (for example) the following can happen:
1. a station connects and is added
2. first, it is added to the driver
3. then, it is added to the mac80211 lists
If the station goes to sleep between steps 2 and 3, and the
firmware/hardware records it as being asleep, mac80211 will
never instruct the driver to wake it up again as it never
realized it went to sleep since the RX path discarded the
frame as a "spurious class 3 frame", no station entry was
present yet.
Fix this by adding the station in software first, and only
then adding it to the driver. That way, any state that the
driver changes will be reflected properly in mac80211's
station state. The problematic part is the roll-back if the
driver fails to add the station, in that case a bit more is
needed. To not make that overly complex prevent starting BA
sessions in the meantime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.
This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.
As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.
Additionally, it can lead to the crash below.
Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.
In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.
BUG: unable to handle kernel
NULL pointer dereference at 000000b0
IP: [<ff6f1791>] ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP: 0060:[<ff6f1791>] EFLAGS: 00210282 CPU: 1
EIP is at ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
EAX: e5900da0 EBX: 00000000 ECX: 00000001 EDX: 00000000
ESI: e41d00c0 EDI: e5900da0 EBP: ebe458e4 ESP: ebe458b0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 000000b0 CR3: 25a78000 CR4: 000407d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process iperf (pid: 3934, ti=ebe44000 task=e757c0b0 task.ti=ebe44000)
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command LQ_CMD (#4e), seq: 0x0903, 92 bytes at 3[3]:9
Stack:
e403b32c ebe458c4 00200002 00200286 e403b338 ebe458cc c10960bb e5900da0
ff76a6ec ebe458d8 00000000 e41d00c0 e5900da0 ebe458f0 ff6f1b75 e403b210
ebe4598c ff723dc1 00000000 ff76a6ec e597c978 e403b758 00000002 00000002
Call Trace:
[<ff6f1b75>] ieee80211_free_txskb+0x15/0x20 [mac80211]
[<ff723dc1>] invoke_tx_handlers+0x1661/0x1780 [mac80211]
[<ff7248a5>] ieee80211_tx+0x75/0x100 [mac80211]
[<ff7249bf>] ieee80211_xmit+0x8f/0xc0 [mac80211]
[<ff72550e>] ieee80211_subif_start_xmit+0x4fe/0xe20 [mac80211]
[<c149ef70>] dev_hard_start_xmit+0x450/0x950
[<c14b9aa9>] sch_direct_xmit+0xa9/0x250
[<c14b9c9b>] __qdisc_run+0x4b/0x150
[<c149f732>] dev_queue_xmit+0x2c2/0xca0
Cc: stable@vger.kernel.org
Reported-by: Yaara Rozenblum <yaara.rozenblum@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
[reword commit log, use a separate lock]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
net/built-in.o:(.rodata+0x1707c): undefined reference to `ip_tunnel_get_stats64'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the kernel tries to announce a zero window when free_space
is below the current receiver mss estimate.
When a sender is transmitting small packets and reader consumes data
slowly (or not at all), receiver might be unable to shrink the receive
win because
a) we cannot withdraw already-commited receive window, and,
b) we have to round the current rwin up to a multiple of the wscale
factor, else we would shrink the current window.
This causes the receive buffer to fill up until the rmem limit is hit.
When this happens, we start dropping packets.
Moreover, tcp_clamp_window may continue to grow sk_rcvbuf towards rmem[2]
even if socket is not being read from.
As we cannot avoid the "current_win is rounded up to multiple of mss"
issue [we would violate a) above] at least try to prevent the receive buf
growth towards tcp_rmem[2] limit by attempting to move to zero-window
announcement when free_space becomes less than 1/16 of the current
allowed receive buffer maximum. If tcp_rmem[2] is large, this will
increase our chances to get a zero-window announcement out in time.
Reproducer:
On server:
$ nc -l -p 12345
<suspend it: CTRL-Z>
Client:
#!/usr/bin/env python
import socket
import time
sock = socket.socket()
sock.setsockopt(socket.IPPROTO_TCP, socket.TCP_NODELAY, 1)
sock.connect(("192.168.4.1", 12345));
while True:
sock.send('A' * 23)
time.sleep(0.005)
socket buffer on server-side will grow until tcp_rmem[2] is hit,
at which point the client rexmits data until -EDTIMEOUT:
tcp_data_queue invokes tcp_try_rmem_schedule which will call
tcp_prune_queue which calls tcp_clamp_window(). And that function will
grow sk->sk_rcvbuf up until it eventually hits tcp_rmem[2].
Thanks to Eric Dumazet for running regression tests.
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message could not be sent out because the destination node
or link could not be found, the full message size is returned from
sendmsg() as if it had been sent successfully. An application will
then get a false indication that it's making forward progress. This
problem has existed since the initial commit in 2.6.16.
We change this to return -ENETUNREACH if the message cannot be
delivered due to the destination node/link being unavailable. We
also get rid of the redundant tipc_reject_msg call since freeing
the buffer and doing a tipc_port_iovec_reject accomplishes exactly
the same thing.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we decide in udp6_sendmsg to send the packet down the ipv4
udp_sendmsg path because the destination is either of family AF_INET or
the destination is an ipv4 mapped ipv6 address, we don't honor the
maybe specified ipv4 mapped ipv6 address in IPV6_PKTINFO.
We simply can check for this option in ip_cmsg_send because no calls to
ipv6 module functions are needed to do so.
Reported-by: Gert Doering <gert@space.net>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include stable fixes for the following bugs:
- General performance regression due to NFS_INO_INVALID_LABEL being set
when the server doesn't support labeled NFS
- Hang in the RPC code due to a socket out-of-buffer race
- Infinite loop when trying to establish the NFSv4 lease
- Use-after-free bug in the RPCSEC gss code.
- nfs4_select_rw_stateid is returning with a non-zero error value on success
Other bug fixes:
- Potential memory scribble in the RPC bi-directional RPC code
- Pipe version reference leak
- Use the correct net namespace in the new NFSv4 migration code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tll2
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.14-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include stable fixes for the following bugs:
- General performance regression due to NFS_INO_INVALID_LABEL being
set when the server doesn't support labeled NFS
- Hang in the RPC code due to a socket out-of-buffer race
- Infinite loop when trying to establish the NFSv4 lease
- Use-after-free bug in the RPCSEC gss code.
- nfs4_select_rw_stateid is returning with a non-zero error value on
success
Other bug fixes:
- Potential memory scribble in the RPC bi-directional RPC code
- Pipe version reference leak
- Use the correct net namespace in the new NFSv4 migration code"
* tag 'nfs-for-3.14-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS fix error return in nfs4_select_rw_stateid
NFSv4: Use the correct net namespace in nfs4_update_server
SUNRPC: Fix a pipe_version reference leak
SUNRPC: Ensure that gss_auth isn't freed before its upcall messages
SUNRPC: Fix potential memory scribble in xprt_free_bc_request()
SUNRPC: Fix races in xs_nospace()
SUNRPC: Don't create a gss auth cache unless rpc.gssd is running
NFS: Do not set NFS_INO_INVALID_LABEL unless server supports labeled NFS
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.
* Don't use the fast payload operation in nf_tables if the length is
not power of 2 or it is not aligned, from Nikolay Aleksandrov.
* Fix missing break statement the inet flavour of nft_reject, which
results in evaluating IPv4 packets with the IPv6 evaluation routine,
from Patrick McHardy.
* Fix wrong kconfig symbol in nft_meta to match the routing realm,
from Paul Bolle.
* Allocate the NAT null binding when creating new conntracks via
ctnetlink to avoid that several packets race at initializing the
the conntrack NAT extension, original patch from Florian Westphal,
revisited version from me.
* Fix DNAT handling in the snmp NAT helper, the same handling was being
done for SNAT and DNAT and 2.4 already contains that fix, from
Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After processing hint_user, we would want to schedule the
timeout work only if we are actually waiting to CRDA. This happens
when the status is not "IGNORE" nor "ALREADY_SET".
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently cache socket policy bundles at xfrm_policy_sk_bundles.
These cached bundles are never used. Instead we create and cache
a new one whenever xfrm_lookup() is called on a socket policy.
Most protocols cache the used routes to the socket, so let's
remove the unused caching of socket policy bundles in xfrm.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
The only place this is used outside rtnetlink.c is veth. So provide
wrapper function for this usage.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's slightly smaller/faster for some architectures.
Make sure def_multicast_addr is __aligned(2)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These include are here since kernel 2.2.7, but probably never used.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_set_csma_params has a redundant (and impossible) check for
"retries", found by smatch. The check was supposed to be for
frame_retries, but wasn't moved during development when
phy_set_frame_retries was introduced. Also, maxBE >= 3 as required by
the standard is not enforced.
Remove the redundant check, assure max_be >= 3 and check -1 <=
frame_retries <= 7 in the correct function.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first glance it looks like there is a missing curly brace but
actually the code works the same either way. I have adjusted the
indenting but left the code the same.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the following functions, which are shorter and more in line
with common naming practice in the network subsystem.
tipc_bclink_send_msg->tipc_bclink_xmit
tipc_bclink_recv_pkt->tipc_bclink_rcv
tipc_disc_recv_msg->tipc_disc_rcv
tipc_link_send_proto_msg->tipc_link_proto_xmit
link_recv_proto_msg->tipc_link_proto_rcv
link_send_sections_long->tipc_link_iovec_long_xmit
tipc_link_send_sections_fast->tipc_link_iovec_xmit_fast
tipc_link_send_sync->tipc_link_sync_xmit
tipc_link_recv_sync->tipc_link_sync_rcv
tipc_link_send_buf->__tipc_link_xmit
tipc_link_send->tipc_link_xmit
tipc_link_send_names->tipc_link_names_xmit
tipc_named_recv->tipc_named_rcv
tipc_link_recv_bundle->tipc_link_bundle_rcv
tipc_link_dup_send_queue->tipc_link_dup_queue_xmit
link_send_long_buf->tipc_link_frag_xmit
tipc_multicast->tipc_port_mcast_xmit
tipc_port_recv_mcast->tipc_port_mcast_rcv
tipc_port_reject_sections->tipc_port_iovec_reject
tipc_port_recv_proto_msg->tipc_port_proto_rcv
tipc_connect->tipc_port_connect
__tipc_connect->__tipc_port_connect
__tipc_disconnect->__tipc_port_disconnect
tipc_disconnect->tipc_port_disconnect
tipc_shutdown->tipc_port_shutdown
tipc_port_recv_msg->tipc_port_rcv
tipc_port_recv_sections->tipc_port_iovec_rcv
release->tipc_release
accept->tipc_accept
bind->tipc_bind
get_name->tipc_getname
poll->tipc_poll
send_msg->tipc_sendmsg
send_packet->tipc_send_packet
send_stream->tipc_send_stream
recv_msg->tipc_recvmsg
recv_stream->tipc_recv_stream
connect->tipc_connect
listen->tipc_listen
shutdown->tipc_shutdown
setsockopt->tipc_setsockopt
getsockopt->tipc_getsockopt
Above changes have no impact on current users of the functions.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.
Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.
Fixes: f9c67811eb ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix soft-interface MTU computation
- fix bogus pointer mangling when parsing the TT-TVLV
container. This bug led to a wrong memory access.
- fix memory leak by properly releasing the VLAN object
after CRC check
- properly check pskb_may_pull() return value
- avoid potential race condition while adding new neighbour
- fix potential memory leak by removing all the references
to the orig_node object in case of initialization failure
- fix the TT CRC computation by ensuring that every node uses
the same byte order when hosts with different endianess are
part of the same network
- fix severe memory leak by freeing skb after a successful
TVLV parsing
- avoid potential double free when orig_node initialization
fails
- fix potential kernel paging error caused by the usage of
the old value of skb->data after skb reallocation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=6IO8
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix soft-interface MTU computation
- fix bogus pointer mangling when parsing the TT-TVLV
container. This bug led to a wrong memory access.
- fix memory leak by properly releasing the VLAN object
after CRC check
- properly check pskb_may_pull() return value
- avoid potential race condition while adding new neighbour
- fix potential memory leak by removing all the references
to the orig_node object in case of initialization failure
- fix the TT CRC computation by ensuring that every node uses
the same byte order when hosts with different endianess are
part of the same network
- fix severe memory leak by freeing skb after a successful
TVLV parsing
- avoid potential double free when orig_node initialization
fails
- fix potential kernel paging error caused by the usage of
the old value of skb->data after skb reallocation
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Andrey Vagin:
When a conntrack is created by kernel, it is initialized (sets
IPS_{DST,SRC}_NAT_DONE_BIT bits in nf_nat_setup_info) and only then it
is added in hashes (__nf_conntrack_hash_insert), so one conntract
can't be initialized from a few threads concurrently.
ctnetlink can add an uninitialized conntrack (w/o
IPS_{DST,SRC}_NAT_DONE_BIT) in hashes, then a few threads can look up
this conntrack and start initialize it concurrently. It's dangerous,
because BUG can be triggered from nf_nat_setup_info.
Fix this race by always setting up nat, even if no CTA_NAT_ attribute
was requested before inserting the ct into the hash table. In absence
of CTA_NAT_ attribute, a null binding is created.
This alters current behaviour: Before this patch, the first packet
matching the newly injected conntrack would be run through the nat
table since nf_nat_initialized() returns false. IOW, this forces
ctnetlink users to specify the desired nat transformation on ct
creation time.
Thanks for Florian Westphal, this patch is based on his original
patch to address this problem, including this patch description.
Reported-By: Andrey Vagin <avagin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Florian Westphal <fw@strlen.de>
ERROR: spaces required and "(foo*)" should be "(foo *)"
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace two magic numbers which intialize clgstate::state.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring