Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds to hdev the connection parameters list (hdev->le_
conn_params). The elements from this list (struct hci_conn_params)
contains the connection parameters (for now, minimum and maximum
connection interval) that should be used during the connection
establishment.
Moreover, this patch adds helper functions to manipulate hdev->le_
conn_params list. Some of these functions are also declared in
hci_core.h since they will be used outside hci_core.c in upcoming
patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK key types available right now are unauthenticated and
authenticated ones. Provide two simple constants for it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The struct smp_ltk does not need to be packed and so remove __packed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The field is not a boolean, it is actually a field for a key type. So
name it properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When encryption for LE links has been enabled, it will always be use
AES-CCM encryption. In case of BR/EDR Secure Connections, the link
will also use AES-CCM encryption. In both cases track the AES-CCM
status in the connection flags.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Originally allowing the use of debug keys was done via the Load Link
Keys management command. However this is BR/EDR specific and to be
flexible and allow extending this to LE as well, make this an independent
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller has been enabled to allow usage of debug keys, then
clearly identify that in the current settings information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch groups the list_head fields from struct hci_dev together
and removes empty lines between them.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch creates two new fields in struct hci_conn to save the
minimum and maximum connection interval values used to establish
the connection this object represents.
This change is required in order to know what parameters the
connection is currently using.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If LTK distribution happens in both directions we will have two LTKs for
the same remote device: one which is used when we're connecting as
master and another when we're connecting as slave. When looking up LTKs
from the locally stored list we shouldn't blindly return the first match
but also consider which type of key is in question. If we do not do this
we may end up selecting an incorrect encryption key for a connection.
This patch fixes the issue by always specifying to the LTK lookup
functions whether we're looking for a master or a slave key.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason why A2MP should need or deserve its on channel type.
Instead we should be able to group all fixed CID users under a single
channel type and reuse as much code as possible for them. Where CID
specific exceptions are needed the chan-scid value can be used.
This patch renames the current A2MP channel type to a generic one and
thereby paves the way to allow converting ATT and SMP (and any future
fixed channel protocols) to use the new channel type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a queue for incoming L2CAP data that's received before
l2cap_connect_cfm is called and processes the data once
l2cap_connect_cfm is called. This way we ensure that we have e.g. all
remote features before processing L2CAP signaling data (which is very
important for making the correct security decisions).
The processing of the pending rx data needs to be done through
queue_work since unlike l2cap_recv_acldata, l2cap_connect_cfm is called
with the hci_dev lock held which could cause potential deadlocks.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For debugging purposes of Secure Connection Only support a simple
debugfs entry is used to indicate if this mode is active or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of security level 4, the RFCOMM sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of security level 4, the L2CAP sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The security level 4 is a new strong security requirement that is based
around 128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms. Which means that E0, SAFER+ and P-192
are not allowed. Only connections created with P-256 resulting from
using Secure Connections support are allowed.
This security level needs to be enforced when Secure Connection Only
mode is enabled for a controller or a service requires FIPS compliant
strong security. Currently it is not possible to enable either of
these two cases. This patch just puts in the foundation for being
able to handle security level 4 in the future.
It should be noted that devices or services with security level 4
requirement can only communicate using Bluetooth 4.1 controllers
with support for Secure Connections. There is no backward compatibilty
if used with older hardware.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is important to know if Secure Connections support has been enabled
for a given remote device. The information is provided in the remote
host features page. So track this information and provide a simple
helper function to extract the status.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current management interface only allows to provide the remote
OOB input of P-192 data. This extends the command to also accept
P-256 data as well. To make this backwards compatible, the userspace
can decide to only provide P-192 data or the combined P-192 and P-256
data. It is also allowed to leave the P-192 data empty if userspace
only has the remote P-256 data.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add function to allow adding P-192 and P-256 data to the internal
storage. This also fixes a few coding style issues from the previous
helper functions for the out-of-band credentials storage.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections has been enabled it is possible to provide P-192
and/or P-256 data during the pairing process. The internal out-of-band
credentials storage has been extended to also hold P-256 data.
Initially the P-256 data will be empty and with Secure Connections enabled
no P-256 data will be provided. This is according to the specification
since it might be possible that the remote side did not provide either
of the out-of-band credentials.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth 4.1 specification with Secure Connections support has
just been released and controllers with this feature are still in
an early stage.
A handful of controllers have already support for it, but they do
not always identify this feature correctly. This debugfs entry
allows to tell the kernel that the controller can be treated as
it would fully support Secure Connections.
Using debugfs to force Secure Connections support of course does
not make this feature magically appear in all controllers. This
is a debug functionality for early adopters. Once the majority
of controllers matures this quirk will be removed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Secure Connections support and the usage of out-of-band pairing,
it is needed to read the P-256 hash and randomizer or P-192 hash and
randomizer. This change will read P-192 data when Secure Connections
is disabled and P-192 and P-256 data when it is enabled.
The difference is between using HCI Read Local OOB Data and using the
new HCI Read Local OOB Extended Data command. The first one has been
introduced with Bluetooth 2.1 and returns only the P-192 data.
< HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
> HCI Event: Command Complete (0x0e) plen 36
Read Local OOB Data (0x03|0x0057) ncmd 1
Status: Success (0x00)
Hash C from P-192: 975a59baa1c4eee391477cb410b23e6d
Randomizer R with P-192: 9ee63b7dec411d3b467c5ae446df7f7d
The second command has been introduced with Bluetooth 4.1 and will
return P-192 and P-256 data.
< HCI Command: Read Local OOB Extended Data (0x03|0x007d) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local OOB Extended Data (0x03|0x007d) ncmd 1
Status: Success (0x00)
Hash C from P-192: 6489731804b156fa6355efb8124a1389
Randomizer R with P-192: 4781d5352fb215b2958222b3937b6026
Hash C from P-256: 69ef8a928b9d07fc149e630e74ecb991
Randomizer R with P-256: 4781d5352fb215b2958222b3937b6026
The change for the management interface is transparent and no change
is required for existing userspace. The Secure Connections feature
needs to be manually enabled. When it is disabled, then userspace
only gets the P-192 returned and with Secure Connections enabled,
userspace gets P-192 and P-256 in an extended structure.
It is also acceptable to just ignore the P-256 data since it is not
required to support them. The pairing with out-of-band credentials
will still succeed. However then of course no Secure Connection will
b established.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for Secure Connections need to be explicitly enabled by
userspace. This is required since only userspace that can handle the
new link key types should enable support for Secure Connections.
This command handling is similar to how Secure Simple Pairing enabling
is done. It also tracks the case when Secure Connections support is
enabled via raw HCI commands. This makes sure that the host features
page is updated as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The MGMT_SETTING_SECURE_CONN setting is used to track the support and
status for Secure Connections from the management interface. For HCI
based tracking HCI_SC_ENABLED flag is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of Secure Connections, the list of link key types
got extended by P-256 versions of authenticated and unauthenticated
link keys.
To avoid any confusion the previous authenticated and unauthenticated
link key types got ammended with a P912 postfix. And the two new keys
have a P256 postfix now. Existing code using the previous definitions
has been adjusted.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Secure Connections feature introduces the support for P-256 strength
pairings (compared to P-192 with Secure Simple Pairing). This however
means that for out-of-band pairing the hash and randomizer needs to be
differentiated. Two new commands are introduced to handle the possible
combinations of P-192 and P-256. This add the HCI command definition
for both.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Secure Connections feature is optional and host stacks have to
manually enable it. This add the HCI command definiton for reading
and writing this setting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for Secure Connections introduces two new controller
features and one new host feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controller pretend they support the Delete Stored Link Key command,
but in reality they really don't support it.
< HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
bdaddr 00:00:00:00:00:00 all 1
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 0
Error: Unsupported Feature or Parameter Value
Not correctly supporting this command causes the controller setup to
fail and will make a device not work. However sending the command for
controller that handle stored link keys is important. This quirk
allows a driver to disable the command if it knows that this command
handling is broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is initial version of
http://tools.ietf.org/html/draft-ietf-6lo-btle-00
By default the 6LoWPAN support is not activated and user
needs to tweak /sys/kernel/debug/bluetooth/hci0/6lowpan
file.
The kernel needs IPv6 support before 6LoWPAN is usable.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the LMP feature constants for connectionless slave broadcast
and use them for capability testing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values in l2cap_chan that are used for actually transmitting data
only need to be initialized right after we've received an L2CAP Connect
Request or just before we send one. The only thing that we need to
initialize though bind() and connect() is the chan->mode value. This way
all other initializations can be done in the l2cap_le_flowctl_init
function (which now becomes private to l2cap_core.c) and the
l2cap_le_flowctl_start function can be completely removed.
Also, since the l2cap_sock_init function initializes the imtu and omtu
to adequate values these do not need to be part of l2cap_le_flowctl_init.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE CoC used differend CIC ranges than BR/EDR L2CAP. The start of the
range is the same (0x0040) but the range ends at 0x007f (unlike BR/EDR
where it goes all the way to 0xffff).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unlike BR/EDR, for LE when we're in the BT_CONNECT state we may or may
not have already have sent the Connect Request. This means that we need
some extra tracking of the request. This patch adds an extra channel
flag to prevent the request from being sent a second time.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Setting the BT_SK_SUSPEND socket flag from the L2CAP core is causing a
dependency on the socket. So instead of doing that, use a channel
callback into the socket handling to suspend.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds new socket options for LE sockets since the existing
L2CAP_OPTIONS socket option is not usable for LE. For now, the new
socket options also require LE CoC support to be explicitly enabled to
leave some playroom in case something needs to be changed in a backwards
incompatible way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds tracking of L2CAP connection oriented channel local and
remote credits to struct l2cap_chan and ensures that connect requests
and responses contain the right values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE connection oriented channels have their own mode with its own
data transfer rules. In order to implement this properly we need to
distinguish L2CAP channels operating in this mode from other modes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the necessary boiler plate code to handle receiving
L2CAP connect requests over LE and respond to them with a proper connect
response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the necessary defines and structs for LE connection
oriented channels.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Along with the L2CAP Connection Oriented Channels features it is now
allowed to use both custom fixed CIDs as well as PSM based (connection
oriented connections). Since the support for this (with the subsequent
patches) is still on an experimental stage, add a module parameter to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
There is no access to chan->sk in L2CAP core now. This change marks the
end of the task of splitting L2CAP between Core and Socket, thus sk is now
gone from struct l2cap_chan.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Adding the channel to the skb private data makes possible to us know which
channel the skb we have came from.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Under Test (DUT) mode is useful for doing certification
testing and so expose this as debugfs option.
This mode is actually special since you can only enter it. Restoring
normal operation means that a HCI Reset is required. The current mode
value gets tracked as a new device flag and when disabling it, the
correct command to reset the controller is sent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For testing purposes expose the default LE connection interval values
via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enabling and disabling SSP debug mode is useful for development. This
adds a debugfs entry that allows to configure the SSP debug mode.
On purpose this has been implemented as debugfs entry and not a public
API since it is really only useful during testing and development.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The conn->interval parameter of HCI connections is not used at all
and so just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The own address type is based on the fact if the controller has
a public address or not. This means that this detail can be just
configured once during setup phase.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The device_add handling can be done directly in hci_register_dev and
device_remove within hci_unregister_dev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The device blacklist is not taking care of the address type. Actually
store the address type in the list entries and also use them when
looking up addresses in the table.
This is actually a serious bug. When adding a LE public address to
the blacklist, then it would be blocking a device on BR/EDR. And this
is not the expected behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to use a timer since the entire Bluetooth subsystem
runs using workqueues these days.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the entire Bluetooth subsystem runs in workqueues these days there
is no need to use a timer for deferring work.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This seems to be a left-over. The module parameter enable_hs has
been removed, but its extern declaration is still present. It is
not needed anymore, so just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The constants for advertising event types have been defined twice. So
remove one copy of it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On controller power on and when enabling LE functionality,
make sure that also the scan response data is correctly set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan response data needs to be stored in HCI device and so
add a buffer for it and also ensure to clear it when resetting
the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_new_ltk() function is not used and
so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_read_local_oob_data_reply_complete() function
is not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_set_local_name_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_set_class_of_dev_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_ssp_enable_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_auth_enable_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_auth_failed() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_pin_code_neg_reply_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_pin_code_reply_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The return value of mgmt_pin_code_request() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The wait_ack code has a heavy dependency on the socket data structures
and, as of now, it won't be worthless change it to use non-socket
structures as the only user of such feature is a socket.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to remove all direct access of struct sock from L2CAP core.
This change is pretty simple and just add a new L2CAP channel callback to
do the work in the L2CAP socket side.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As part of the work to remove struct sock from l2cap_core.c and make it
more generic we remove in this commit the direct access to sk->sk_sndtimeo
member. This objective of this change is purely remove sk usage from
l2cap_core.c
Now we have a new l2cap ops to get the current value of sk->sndtimeo. A
l2cap_chan_no_get_sndtimeo was added for users of L2CAP that doesn't need
to set a timeout.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of creating an new function pointer to report errors we are just
reusing state_change for that and there is a simple reason for this, one
place in the l2cap_core.c code needs, in a locked sk, set both the sk_state
and sk_err. If we create two different functions for this we would need to
release the lock between the two operation putting the socket in non
desired state.
The change is transparent to the l2cap_core.c code, user that only needs
to set the state won't need any modification.
This is another step of an ongoing work to make l2cap_core.c totally
independent from l2cap's struct sock.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the discoverable timeout triggers and limited discoverable mode
was used, then the class of device needs to be updated to remove
the limited discoverable bit.
To keep the class of device logic in a central place, expose a new
function mgmt_discoverable_timeout that can be called from the
timeout callback. In case the class of device value needs updating,
it will add the HCI command to the transaction.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The eir_get_length() function is only used from hci_event.c and so
instead of having a public function move it to the location where
it is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The eir_append_data() function is only used from mgmt.c and so
instead of having a public function move it to the location where
it is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_new_link_key() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch just adds the HCI command structure for configuring the
current IAC LAP setting. The length of the command is variable and
supports more than two IAC. However since there is only general
discoverable and limited discoverable modes, this can be limited
to two possible IACs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_write_scan_failed() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_connectable() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_discoverable() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a new flag that can be set when in limited discoverable mode. This
flag will cause the limited discoverable bit in the class of device
value to bet set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Magically updating the advertising data when some random command enables
advertising in the controller is not really a good idea. It also caused
a bit of complicated code with the exported hci_udpate_ad function that
is shared from many places.
This patch consolidates the advertising data update into the management
core. It also makes sure that when powering on with LE enabled or later
on enabling LE the controller has a good default for advertising data.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Read the current IAC LAP values when initializing the controller. The
values are not used, but it is good to have them in the trace files
for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When initializing a controller make sure to read out the number of
supported IAC and store its result. This value is needed to determine
if limited discoverable for BR/EDR can be configured or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Clearing the BT_SK_SUSPEND socket flag from the L2CAP core is causing
a dependency on the socket. So intead of doing that, use a channel
callback into the socket handling to resume.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP core should not look into the socket flags to figure out the
setting of defer setup. So introduce a L2CAP channel flag that mirrors
the socket flag.
Since the defer setup option is only set in one place this becomes a
really easy thing to do.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP connectionless channels use SOCK_DGRAM and recvmsg() and need
to receive the remote BD_ADDR and PSM information via msg_name from
the recvmsg() system call.
So in case the L2CAP socket is for connectionless channels, provide
a msg_name callback that can update the data. Also store the remote
BD_ADDR and PSM in the skb so it can be extracted later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows to add a per socket msg_name callback that can be used
for updating the msg_name information for recvmsg() system calls.
This feature is used by another patch to support address information
on L2CAP connectionless channels.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Every socket protocol now stores its own address information. So
just remove the generic src and dst fields since they are no longer
needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of RFCOMM sockets should be stored in its
own socket structure. Trying to generalize them is not helpful since
different transports have different address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of SCO sockets should be stored in its own
socket structure. Trying to generalize them is not helpful since
different transports have different address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of storing a pointer to the addresses for the HCI device
and HCI connection, use them directly. With the recent changes
to address tracking of HCI connections, this becomes simple.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP sockets can use BR/EDR public, LE public and LE random
addresses for various combinations of source and destination
devices. So make sure that getsockname(), getpeername() and
accept() return the correct address type.
For this the address type of the source and destination is stored
with the L2CAP channel information. The stored address type is
not the one specific for the HCI protocol. It is the address
type used for the L2CAP sockets and the management interface.
The underlying HCI connections store the HCI address type. If
needed, it gets converted to the socket address type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the effort of abstracting the L2CAP socket from the underlying
L2CAP channel it is important to store the source and destination
address information directly in the L2CAP channel structure.
Direct access to the HCI connection address information is not
possible since they might not be avaiable at L2CAP channel
creation time. The address information will be updated when
the underlying BR/EDR or LE connection status changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The source addressed was based on the public address of the HCI device,
but with LE connections this not always the case. For example single
mode LE-only controllers would use a static random address. And this
address is configured by userspace.
To not complicate the lookup of what kind of address is in use, store
the correct source address for each HCI connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When establishing LE connections, it is possible to use a public
address (if available) or a random address. The type of address
is only known when creating connections, so make sure it is
stored in hci_conn structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bdaddr_to_le() function tries to convert the internal address
type to one that matches the HCI address type for LE. It does not
handle any address types not used by LE and in the end just make
the code a lot harder to read.
So instead of just hiding behind a magic function, just convert
the internal address type where it needs to be converted. And it
turns out that these are only two cases anyway. One when creating
new LE connections and the other when loading the long term keys.
In both cases this makes it more clear on what it going on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The l2cap_conn->src and l2cap_conn->dst pointers are no longer in use
and so just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The implementation actually supports the L2CAP connectionless data
channel. So set it as supported in the fixed channels bitmask.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The PSM 0x0021 is dedicated to the 3D profile and has permission to
use security mode 4 level 0 for L2CAP connectionless unicast data
transfers.
When establishing a L2CAP connectionless channel on PSM 0x0021, it
will no longer force Secure Simple Pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window parameters are used for LE passive
background scanning and connection establishment. This allows
userspace to change the values.
These two values should be kept in sync with whatever is used for
the scan parameters service on remote devices. And it puts the
controlling daemon (for example bluetoothd) in charge of setting
the values.
Main use case would be to switch between two sets of values. One
for foreground applications and one for background applications.
At this moment, the values are only used for manual connection
establishment, but soon that should be extended to background
scanning and automatic connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window for LE passive scanning and connection
establishment should be configurable on a per controller basis. So
introduce a setting that later on will allow modifying it.
This setting does not affect LE active scanning during device
discovery phase. As long as that phase uses interleaved discovery,
it will continuously scan.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The amp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since there is no use of hdev->ioctl by any Bluetooth driver since
ever, so just lets remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_discovering() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_remote_name() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_found() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_disconnected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_connected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_connect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_disconnect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_set_powered_failed() function is never used
and so make the function just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value from mgmt_index_added() and mgmt_index_removed()
functions is never used. So do not pretend that returning an error
would actually be handled and just make both functions return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The helper function mgmt_valid_hdev() is more obfuscating the code
then it makes it easier to read. So intead of this helper, use the
direct check for BR/EDR device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The mgmt_new_settings() function was only needed to handle the
error case when re-enabling advertising failed. Since that is
now handled internally inside the management core, this function
is not needed anymore. So just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the all LE connections have been disconneted, then it is up to
the host to re-enable advertising at that point. To ensure that the
correct advertising parameters are used, force the usage of the
common helper to enable advertising.
The change just moves the manual enabling of advertising from the
event handler into the management core so that the helper can
be actually shared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the basic HCI structure for building the LE advertising parameters
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_amp_capable() function has only a single user inside the L2CAP
core. Instead of exporting the function, place it next to its user.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AMP controller status constants need to be actually used to avoid
crypted hardcoded numbers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The special AMP controller id 0 is reserved for the BR/EDR controller
that has the main link. It is a fixed value and so use a constant for
this throughout the code to make it more visible when the handling is
for the BR/EDR channel or when it is for the AMP channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are two defined HCI device types. One is for BR/EDR controllers
and the other is for AMP controllers. The HCI device type is not the
same as the AMP controller type. It just happens that currently the
defined types match, but that is not guaranteed.
Split the usage of AMP controller type into its own domain so that
it is possible to separate between BR/EDR controllers, 802.11 AMP
controllers and any other AMP technology that might be defined in
the future.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the constants for BR/EDR and 802.11 AMP controller types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The list of controllers can be counted ahead of time and inline
inside the AMP discover handling. There is no need to export such
a function at all.
In addition just count the AMP controller and only allocated space
for a single mandatory BR/EDR controller. No need to allocate more
space than needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A function is needed so that the HCI event processing can ask the mgmt
code to emit a new settings event. This is necessary e.g. when the event
processing does updates to mgmt related states without any dependency of
actual mgmt commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag is used to indicate whether we want to have advertising
enabled or not, so give it a more suitable name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 110
"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.
Event Parameters: NONE"
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Synchronization Train Complete event indicates that the Start
Synchronization Train command has completed.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 103
"7.7.67 Synchronization Train Complete Event [New Section]
...
Event Parameters:
Status 0x00 Start Synchronization Train command completed
successfully.
0x01-0xFF Start Synchronization Train command failed.
See Part D, Error Codes, for error codes and
descriptions."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 86
"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.
Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 78
"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.
The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.
The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.
The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 97
"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.
Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 93
"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.
The Data_Length field may be zero, in which case no data needs to be
provided.
The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 92
"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 90
"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.
This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.
The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).
Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).
This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.
We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.
This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mgmt command for enabling and disabling
LE advertising. The command depends on the LE setting being enabled
first and will return a "rejected" response otherwise. The patch also
adds safeguards so that there will ever only be one set_le or
set_advertising command pending per adapter.
The response handling and new_settings event sending is done in an
asynchronous request callback, meaning raw HCI access from user space to
enable advertising (e.g. hciconfig leadv) will not trigger the
new_settings event. This is intentional since trying to support mixed
raw HCI and mgmt access would mean adding extra state tracking or new
helper functions, essentially negating the benefit of using the
asynchronous request framework. The HCI_LE_ENABLED and HCI_LE_PERIPHERAL
flags however are updated correctly even with raw HCI access so this
will not completely break subsequent access over mgmt.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a new mgmt setting for LE advertising and hooks up the
necessary places in the mgmt code to operate on the HCI_LE_PERIPHERAL
flag (which corresponds to this setting). This patch does not yet add
any new command for enabling the setting - that is left for a subsequent
patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch updates the code to use an asynchronous request for handling
the enabling and disabling of LE support. This refactoring is necessary
as a preparation for adding advertising support, since when LE is
disabled we should also disable advertising, and the cleanest way to do
this is to perform the two respective HCI commands in the same
asynchronous request.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For those controller that support the HCI_Set_Event_Mask_Page_2 command
we should include it in the init sequence. This patch implements sending
of the command and enables the events in it based on supported features
(currently only CSB is checked).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds support for reading the synchronization train parameters
for controllers that support the feature. Since the feature is
detectable through the local features page 2, which is retreived only in
stage 3 of the HCI init sequence, there is no other option than to add a
fourth stage to the init sequence.
For now the patch doesn't yet add storing of the parameters, but it is
nevertheless convenient to have around to see what kind of parameters
various controllers use by default (analyzable e.g. with the btmon user
space tool).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In the case of blocking sockets we should not proceed with sendmsg() if
the socket has the BT_SK_SUSPEND flag set. So far the code was only
ensuring that POLLOUT doesn't get set for non-blocking sockets using
poll() but there was no code in place to ensure that blocking sockets do
the right thing when writing to them.
This patch adds a new bt_sock_wait_ready helper function to sleep in the
sendmsg call if the BT_SK_SUSPEND flag is set, and wake up as soon as it
is unset. It also updates the L2CAP and RFCOMM sendmsg callbacks to take
advantage of this new helper function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The struct for HCI_Set_Event_Mask is never used. Instead a local 8-byte
array is used for sending this command. Therefore, remove the
unnecessary struct definition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introcuces a new HCI socket channel that allows user
applications to take control over a specific HCI device. The application
gains exclusive access to this device and forces the kernel to stay away
and not manage it. In case of the management interface it will actually
hide the device.
Such operation is useful for security testing tools that need to operate
underneath the Bluetooth stack and need full control over a device. The
advantage here is that the kernel still provides the service of hardware
abstraction and HCI level access. The use of Bluetooth drivers for
hardware access also means that sniffing tools like btmon or hcidump
are still working and the whole set of transaction can be traced with
existing tools.
With the new channel it is possible to send HCI commands, ACL and SCO
data packets and receive HCI events, ACL and SCO packets from the
device. The format follows the well established H:4 protocol.
The new HCI user channel can only be established when a device has been
through its setup routine and is currently powered down. This is
enforced to not cause any problems with current operations. In addition
only one user channel per HCI device is allowed. It is exclusive access
for one user application. Access to this channel is limited to process
with CAP_NET_RAW capability.
Using this new facility does not require any external library or special
ioctl or socket filters. Just create the socket and bind it. After that
the file descriptor is ready to speak H:4 protocol.
struct sockaddr_hci addr;
int fd;
fd = socket(AF_BLUETOOTH, SOCK_RAW, BTPROTO_HCI);
memset(&addr, 0, sizeof(addr));
addr.hci_family = AF_BLUETOOTH;
addr.hci_dev = 0;
addr.hci_channel = HCI_CHANNEL_USER;
bind(fd, (struct sockaddr *) &addr, sizeof(addr));
The example shows on how to create a user channel for hci0 device. Error
handling has been left out of the example. However with the limitations
mentioned above it is advised to handle errors. Binding of the user
cahnnel socket can fail for various reasons. Specifically if the device
is currently activated by BlueZ or if the access permissions are not
present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introduces a new user channel flag that allows to give full
control of a HCI device to a user application. The kernel will stay away
from the device and does not allow any further modifications of the
device states.
The existing raw flag is not used since it has a bit of unclear meaning
due to its legacy. Using a new flag makes the code clearer.
A device with the user channel flag set can still be enumerate using the
legacy API, but it does not longer enumerate using the new management
interface used by BlueZ 5 and beyond. This is intentional to not confuse
users of modern systems.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.
When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.
To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.
These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add macros for the HCI capabilities as described in the Bluetooth Core
Specification v4.0, Volume 2, part E, section 7.1.29.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Remove HCI_LINK_KEYS flag since using HCI_MGMT is enough for test that
user space expects the kernel managing link keys.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes hci_do_inquiry and hci_cancel_inquiry helpers. We
now use the HCI request framework in device discovery functionality
and these helpers are no longer needed.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes the LE scan helpers hci_le_scan and hci_cancel_
le_scan and all code related to it. We now use the HCI request
framework in device discovery functionality and these helpers are
no longer needed.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
mgmt_stop_discovery_failed is now only used in mgmt.c so we can
make it a local function. This patch also moves the mgmt_stop_
discovery_failed definition up in mgmt.c to avoid forward
declaration.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to have a better HCI error handling in interleaved discovery
functionality, we should use the HCI request framework.
This patch updates le_scan_disable_work function so it uses the
HCI request framework instead of the hci_send_cmd helper. A complete
callback is registered (le_scan_disable_work_complete function) so we
are able to trigger the inquiry procedure (if we are running the
interleaved discovery) or to stop the discovery procedure (if we are
running LE-only discovery).
This patch also removes the extra logic in hci_cc_le_set_scan_enable
to trigger the inquiry procedure and the mgmt_interleaved_discovery
function since they become useless.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some of discovery macros will be used in hci_core so we need to
define them in common place such as hci_core.h. Thus, this patch
moves discovery macros to hci_core.h and also adds the DISCOV_
prefix to them.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
mgmt_start_discovery_failed is now only used in mgmt.c so we can
make it a local function. This patch also moves the mgmt_start_
discovery_failed definition up in mgmt.c to avoid forward
declaration.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to use HCI request framework in start_discovery, we'll need
to call inquiry_cache_flush in mgmt.c. Therefore, this patch adds the
hci_ prefix to inquiry_cache_flush and makes it non-static.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In future Core Specification versions the ATT CID will be just one of
many possible CIDs that can be used for data transfer. Therefore, it
makes sense to rename the define for the ATT CID to something less
ambigous.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
All HCI command send functions that take a pointer to the command
parameters do not need to modify the content in any way (they merely
copy the data to an skb). Therefore, the parameter type should be
declared const. This also allows passing already const parameters to
these APIs which previously would have generated a compiler warning.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch renames LE_SCANNING_ENABLED and LE_SCANNING_DISABLED
macros to LE_SCAN_ENABLE and LE_SCAN_DISABLE in order to keep
the same prefix others LE scan macros have.
It also fixes le_scan_enable_req function so it uses the LE_SCAN_
ENABLE macro instead of a magic number.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds macros for filter_duplicates parameter values from
HCI LE Set Scan Enable command. It also fixes le_scan_enable_req
function so it uses the LE_SCAN_FILTER_DUP_ENABLE macro instead of
a magic number.
The LE_SCAN_FILTER_DUP_DISABLE was also defined since it will be
required to properly support the GAP Observer Role.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds macros for active and passive LE scan type values.
The LE_SCAN_PASSIVE was also defined since it will be used in future
by LE connection routine and GAP Observer Role support.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
With the introduction of CSA4 there is now also a features page number 2
available. This patch increments the maximum supported page number to 2
and adds code for reading all available pages (as long as we have
support for them - indicated by HCI_MAX_PAGES).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The local and remote features are organized by page number. Page 0
are the LMP features, page 1 the host features, and any pages beyond 1
features that future core specification versions may define. So far
we've only had the first two pages and two separate variables has been
convenient enough, however with the introduction of Core Specification
Addendum 4 there are features defined on page 2.
Instead of requiring the addition of a new variable each time a new page
number is defined, this patch refactors the code to use a single table
for the features. The patch needs to update both the hci_dev and
hci_conn structures since there are macros that depend on the features
being represented in the same way in both of them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since this function is only used by sco, move it from hci_event.c to
sco.c and rename to sco_conn_defer_accept. Make it static.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Several sub-modules like HIDP, rfcomm, ... need to track l2cap
connections. The l2cap_conn->hcon->dev object is used as parent for sysfs
devices so the sub-modules need to be notified when the hci_conn object is
removed from sysfs.
As submodules normally use the l2cap layer, the l2cap_user objects are
registered there instead of on the underlying hci_conn object. This avoids
any direct dependency on the HCI layer and lets the l2cap core handle any
specifics.
This patch introduces l2cap_user objects which contain a "probe" and
"remove" callback. You can register them on any l2cap_conn object and if
it is active, the "probe" callback will get called. Otherwise, an error is
returned.
The l2cap_conn object will call your "remove" callback directly before it
is removed from user-space. This allows you to remove your submodules
_before_ the parent l2cap_conn and hci_conn object is removed.
At any time you can asynchronously unregister your l2cap_user object if
your submodule vanishes before the l2cap_conn object does.
There is no way around l2cap_user. If we want wire-protocols in the
kernel, we always want the hci_conn object as parent in the sysfs tree. We
cannot use a channel here since we might need multiple channels for a
single protocol.
But the problem is, we _must_ get notified when an l2cap_conn object is
removed. We cannot use reference-counting for object-removal! This is not
how it works. If a hardware is removed, we should immediately remove the
object from sysfs. Any other behavior would be inconsistent with the rest
of the system. Also note that device_del() might sleep, but it doesn't
wait for user-space or block very long. It only _unlinks_ the object from
sysfs and the whole device-tree. Everything else is handled by ref-counts!
This is exactly what the other sub-modules must do: unlink their devices
when the "remove" l2cap_user callback is called. They should not do any
cleanup or synchronous shutdowns.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If we want to use l2cap_conn outside of l2cap_core.c, we need refcounting
for these objects. Otherwise, we cannot synchronize l2cap locks with
outside locks and end up with deadlocks.
Hence, introduce ref-counting for l2cap_conn objects. This doesn't affect
l2cap internals at all, as they use a direct synchronization.
We also keep a reference to the parent hci_conn for locking purposes as
l2cap_conn depends on this. This doesn't affect the connection itself but
only the lifetime of the (dead) object.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There is no reason to require the source arguments to be writeable so fix
this to allow constant source addresses.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We currently do not allow using hci_conn from outside of HCI-core.
However, several other users could make great use of it. This includes
HIDP, rfcomm and all other sub-protocols that rely on an active
connection.
Hence, we now introduce hci_conn ref-counting. We currently never call
get_device(). put_device() is exclusively used in hci_conn_del_sysfs().
Hence, we currently never have a greater device-refcnt than 1.
Therefore, it is safe to move the put_device() call from
hci_conn_del_sysfs() to hci_conn_del() (it's the only caller). In fact,
this even fixes a "use-after-free" bug as we access hci_conn after calling
hci_conn_del_sysfs() in hci_conn_del().
From now on we can add references to hci_conn objects in other layers
(like l2cap_sock, HIDP, rfcomm, ...) and grab a reference via
hci_conn_get(). This does _not_ guarantee, that the connection is still
alive. But, this isn't what we want. We can simply lock the hci_conn
device and use "device_is_registered(hci_conn->dev)" to test that.
However, this is hardly necessary as outside users should never rely on
the HCI connection to be alive, anyway. Instead, they should solely rely
on the device-object to be available.
But if sub-devices want the hci_conn object as sysfs parent, they need to
be notified when the connection drops. This will be introduced in later
patches with l2cap_users.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
hci_conn_hold/put_device() is used to control when hci_conn->dev is no
longer needed and can be deleted from the system. Lets first look how they
are currently used throughout the code (excluding HIDP!).
All code that uses hci_conn_hold_device() looks like this:
...
hci_conn_hold_device();
hci_conn_add_sysfs();
...
On the other side, hci_conn_put_device() is exclusively used in
hci_conn_del().
So, considering that hci_conn_del() must not be called twice (which would
fail horribly), we know that hci_conn_put_device() is only called _once_
(which is in hci_conn_del()).
On the other hand, hci_conn_add_sysfs() must not be called twice, either
(it would call device_add twice, which breaks the device, see
drivers/base/core.c). So we know that hci_conn_hold_device() is also
called only once (it's only called directly before hci_conn_add_sysfs()).
So hold and put are known to be called only once. That means we can safely
remove them and directly call hci_conn_del_sysfs() in hci_conn_del().
But there is one issue left: HIDP also uses hci_conn_hold/put_device().
However, this case can be ignored and simply removed as it is totally
broken. The issue is, the only thing HIDP delays with
hci_conn_hold_device() is the removal of the hci_conn->dev from sysfs.
But, the hci_conn device has no mechanism to get notified when its own
parent (hci_dev) gets removed from sysfs. hci_dev_hold/put() does _not_
control when it is removed but only when the device object is created
and destroyed.
And hci_dev calls hci_conn_flush_*() when it removes itself from sysfs,
which itself causes hci_conn_del() to be called, but it does _not_ cause
hci_conn_del_sysfs() to be called, which is wrong.
Hence, we fix it to call hci_conn_del_sysfs() in hci_conn_del(). This
guarantees that a hci_conn object is removed from sysfs _before_ its
parent hci_dev is removed.
The changes to HIDP look scary, wrong and broken. However, if you look at
the HIDP session management, you will notice they're already broken in the
exact _same_ way (ever tried "unplugging" HIDP devices? Breaks _all_ the
time).
So this patch only makes HIDP look _scary_ and _obviously broken_. It does
not break HIDP itself, it already is!
See later patches in this series which fix HIDP to use proper
session-management.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().
hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.
But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We need to verify that the given sockets actually are l2cap sockets. If
they aren't, we are not supposed to access bt_sk(sock) and we shouldn't
start the session if the offsets turn out to be valid local BT addresses.
That is, if someone passes a TCP socket to HIDCONNADD, then we access some
random offset in the TCP socket (which isn't even guaranteed to be valid).
Fix this by checking that the socket is an l2cap socket.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The driver init queue is no longer needed. This can be all handled
inside the drivers now. So remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some drivers require a special stage for their early init. This is
always specific to the driver or transport. So call back into driver to
allow bringing up the device.
The advantage with this stage is that the Bluetooth core is actually
handling the HCI layer now. This means that command and event processing
is available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a __hci_cmd_sync_ev function, analogous to
__hci_cmd_sync except that it also takes an event parameter to indicate
that the command completes with a special event instead of command
complete. Internally this new function takes advantage of the
hci_req_add_ev function introduced in the previous patch.
The primary expected user of this new function are the setup routines of
HCI drivers which may want to send custom commands and return only when
they have completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for having commands within HCI requests that do
not result in a command complete but some other event. This is at least
needed for some vendor specific commands to be issued in the
hdev->setup() procecure, but might also be useful for other commands.
The way that the support is implemented is by extending the skb control
buffer to have a field to indicate that the command is expected to
terminate with a special event. After sending the command each received
event can then be compared against this field through hdev->sent_cmd.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a helper function for sending a single HCI command
waiting for its completion and then returning back the parameters in the
resulting command complete event (if there was one).
The implementation is very similar to that of hci_req_sync() except that
instead of invocing a callback for sending HCI commands the function
constructs and sends one itself and after being woken up picks the last
received event from hdev->recv_evt (if it matches the right criteria)
and returns it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds tracking of received HCI events to the hci_dev struct.
This is necessary so that a subsequent patch can implement a function
for sending a single command synchronously and returning the resulting
command complete parameters in the function return value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the hci_req_cmd_status function since it is not
used anymore. The HCI request framework now considers the HCI command
has complete once the Command Status or Command Complete Event is
received.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These parameters are related to the "fast connectable" mode that can be
changed through the mgmt interface. Not all controllers properly reset
these values with HCI_Reset so they need to be read in order to be able
to verify whether the values are correct or not before enabling page
scan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to be able to represent fast connectable mode in the mgmt
settings we need to have a HCI dev flag for it. This patch adds the flag
and makes sure its value is changed whenever a mgmt_set_fast_connectable
command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For proper control of the AD update and the related HCI commands it's
best to run the AD update through an async request instead of a
standalone HCI command. This patch changes the hci_update_ad() function
to take a request pointer and updates its users appropriately. E.g. the
function is no longer called after the init sequence but during stage 3
of the init sequence.
The TX power is read during the init sequence, so we don't need an
explicit update whenever it is read and the AD update based on the local
name should be done through the local name mgmt handler. The only other
user is the update based on enabling advertising. This part is still
kept as there is no mgmt API to enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We'll need to use this mask also when powering off the HCI device
so it's better to have this in a single and visible place.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Now that class related operations are tracked through asynchronous HCI
requests this flag is no longer needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since no one checks the returning value of hci_req_add and HCI
request errors are now handled in hci_req_run, we can make hci_
req_add returning void.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When we are building a HCI request with more than one HCI command
and one of the hci_req_add calls fail, we should have some cleanup
routine so the HCI commands already queued on HCI request can be
deleted. Otherwise, we will face some memory leaks issues.
This patch implements the HCI request error handling which is the
following: If a hci_req_add fails, we save the error code in hci_
request. Once hci_req_run is called, we verify the error field. If
it is different from zero, we delete all HCI commands already queued
and return the error code.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This variable is no longer needed (due to async HCI request support and
the conversion of hci_req_sync to use it), so it can be safely removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch converts the hci_req_sync() procedure to internaly use the
asynchronous HCI requests.
The hci_req_sync mechanism relies on hci_req_complete() calls from
hci_event.c into hci_core.c whenever a HCI command completes. This is
very similar to what asynchronous requests do and makes the conversion
fairly straight forward by converting hci_req_complete into a request
complete callback. By this change hci_req_complete (renamed to
hci_req_sync_complete) becomes private to hci_core.c and all calls to it
can be removed from hci_event.c.
The commands in each hci_req_sync procedure are collected into their own
request by passing the hci_request pointer to the request callback
(instead of the hci_dev pointer). The one slight exception is the HCI
init request which has the special handling of HCI driver specific
initialization commands. These commands are run in their own request
prior to the "main" init request.
One other extra change that this patch must contain is the handling of
spontaneous HCI reset complete events that some controllers exhibit.
These were previously handled in the hci_req_complete function but the
right place for them now becomes the hci_req_cmd_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introduces functions to process the HCI request state when
receiving HCI Command Status or Command Complete events. Some HCI
commands, like Inquiry do not result in a Command complete event so
special handling is needed for them. Inquiry is a particularly important
one since it is the only forseeable "non-cmd_complete" command that will
make good use of the request functionality, and its completion is either
indicated by an Inquiry Complete event of a successful Command Complete
for HCI_Inquiry_Cancel.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This function is analogous to hci_send_cmd() but instead of directly
queuing the command to hdev->cmd_q it adds it to the local queue of the
asynchronous HCI request being build (inside struct hci_request).
This is the main function used for building asynchronous requests and
there should be one or more calls to it between calls to hci_req_init
and hci_req_run.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds the initial definitions and functions for asynchronous
HCI requests. Asynchronous requests are essentially a group of HCI
commands together with an optional completion callback. The request is
tracked through the already existing command queue by having the
necessary context information as part of the control buffer of each skb.
The only information needed in the skb control buffer is a flag for
indicating that the skb is the start of a request as well as the
optional complete callback that should be used when the request is
complete (this will be found in the last skb of the request).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Previous commits have improved the handling of the RFCOMM session
timer and the RFCOMM session pointers such that freed RFCOMM
session structures should no longer be erroneously accessed. The
RFCOMM session refcnt now has no purpose and will be deleted by
this commit.
Note that the RFCOMM session is now deleted as soon as the
RFCOMM control channel link is no longer required. This makes the
lifetime of the RFCOMM session deterministic and absolute.
Previously with the refcnt, there was uncertainty about when
the session structure would be deleted because the relative
refcnt prevented the session structure from being deleted at will.
It was noted that the refcnt could malfunction under very heavy
real-time processor loading in embedded SMP environments. This
could cause premature RFCOMM session deletion or double session
deletion that could result in kernel crashes. Removal of the
refcnt prevents this issue.
There are 4 connection / disconnection RFCOMM session scenarios:
host initiated control link ---> host disconnected control link
host initiated ctrl link ---> remote device disconnected ctrl link
remote device initiated ctrl link ---> host disconnected ctrl link
remote device initiated ctrl link ---> remote device disc'ed ctrl link
The control channel connection procedures are independent of the
disconnection procedures. Strangely, the RFCOMM session refcnt was
applying special treatment so erroneously combining connection and
disconnection events. This commit fixes this issue by removing
some session code that used the "initiator" member of the session
structure that was intended for use with the data channels.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Unfortunately, the design retains local copies of the s RFCOMM
session pointer in various code blocks and this invites the erroneous
access to a freed RFCOMM session structure.
Therefore, return the RFCOMM session pointer back up the call stack
to avoid accessing a freed RFCOMM session structure. When the RFCOMM
session is deleted, NULL is passed up the call stack.
If active DLCs exist when the rfcomm session is terminating,
avoid a memory leak of rfcomm_dlc structures by ensuring that
rfcomm_session_close() is used instead of rfcomm_session_del().
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There is no reason a caller ever wants to check the return type of this
call. _Iff_ a user successfully called bt_sock_register(), they're allowed
to call bt_sock_unregister().
All other calls in the kernel (device_del, device_unregister, kfree(), ..)
that are logically equivalent return void. Lets not make callers think
they have to check the return type of this call and instead simply return
void.
We guarantee that after bt_sock_unregister() is called, the socket type
_is_ unregistered. If that is not what the caller wants, they're using the
wrong function, anyway.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
As hci_acl_disconn function basically sends the HCI Disconnect Command
and it is used to disconnect ACL, SCO and LE links, renaming it to
hci_disconnect is more suitable.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The primary purpose of the UUIDs is to enable generation of EIR and AD
data. In these data formats the UUIDs are split into separate fields
based on whether they're 16, 32 or 128 bit UUIDs. To make the generation
of these data fields simpler this patch adds a type member to the
bt_uuid struct and assigns a value to it as soon as the UUID is added to
the kernel. This way the type doesn't need to be calculated each time
the UUID list is later iterated.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The LE supported states indicate the states and state combinations that
the link layer supports. This is important information for knowing what
operations are possible when dealing with multiple connected devices.
This patch adds reading of the supported states to the HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The LE White List Size is necessary to be known before attempting to
feed the controller with any addresses intended for the white list. This
patch adds the necessary HCI command sending to the HCI init sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To be able to make the appropriate decisions for some LE procedures we
need to know the LE features that the local controller supports.
Therefore, it's important to have the LE Read Local Supported Features
HCI comand as part of the HCI init sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds two helper functions to test for valid bdaddr type
values. These will be particularely useful in the mgmt code to check
that user space has passed valid values to the kernel.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The hci_request function is blocking and cannot be called through the
usual per-HCI device workqueue (hdev->workqueue). While hci_request is
in progress any other work from the queue, including sending HCI
commands to the controller would be blocked and eventually cause the
hci_request call to time out.
This patch adds a second workqueue to be used by operations needing
hci_request and thereby avoiding issues with blocking other workqueue
users.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Using bit operations solves problems with multiple requests
and clearing state.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes srej_queue_next from include/net/bluetooth/l2cap.h as it
is not used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make code more readable by changing CONF_NO_FCS_RECV which is read
as "No L2CAP FCS option received" to CONF_RECV_NO_FCS which means
"Received L2CAP option NO_FCS". This flag really means that we have
received L2CAP FRAME CHECK SEQUENCE (FCS) OPTION with value "No FCS".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Before starting quering remote AMP controllers make sure
that there is local active AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some comparisons needs to double negation(!!) in order to make the value
of the field boolean. Add it to the macro makes the code more readable.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to authenticate and configure an incoming SCO connection, the
BT_DEFER_SETUP option was added. This option is intended to defer reply
to Connect Request on SCO sockets.
When a connection is requested, the listening socket is unblocked but
the effective connection setup happens only on first recv. Any send
between accept and recv fails with -ENOTCONN.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Read Local OOB Data command can take more than 1 second on some chips.
e.g. on CSR 0a12:0001 first call to Read Local OOB Data after reset
takes about 1300ms resulting in tx timeout error.
[27698.368655] Bluetooth: hci0 command 0x0c57 tx timeout
2012-10-31 15:53:36.178585 < HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
2012-10-31 15:53:37.496996 > HCI Event: Command Complete (0x0e) plen 36
Read Local OOB Data (0x03|0x0057) ncmd 1
status 0x00
hash 0x92219d9b447f2aa9dc12dda2ae7bae6a
randomizer 0xb1948d0febe4ea38ce85c4e66313beba
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a callback for the HCI_LE_Set_Advertise_Enable command.
The callback is responsible for updating the HCI_LE_PERIPHERAL flag
updating as well as updating the advertising data flags field to
indicate undirected connectable advertising.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds support for setting basing LE advertising data. The
three elements supported for now are the advertising flags, the TX power
and the friendly name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The core specification defines 127 as the "not available" value (well,
"reserved" for BR/EDR and "not available" for LE - but essentially the
same). Therefore, instead of testing for 0 (which is in fact a valid
value) we should be using this invalid value to test if the tx_power is
available.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The actual parameter order of hci_get_route is (dst, src) and not (src,
dst). All current callers use the right order but the header file shows
the parameters in the wrong order.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since we have started to use local_amp_id for local AMP
Controller Id it makes sense to rename ctrl_id to remote_amp_id
since it represents remote AMP controller Id.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving HCI Phylink Complete event run amp_physical_cfm
which initialize BR/EDR L2CAP channel associated with High Speed
link and run l2cap_physical_cfm which shall send L2CAP Create
Chan Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Disconnect logical link for high speed channel hs_hchan
associated with L2CAP channel chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After physical link is created logical link needs to be created.
The process starts after L2CAP channel is created and L2CAP
Configuration Response with result PENDING is received.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes sending an unnecessary HCI_Write_SSP_Mode command if
the command has already been sent as part of the default HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a flag to be used for LE GAP Peripheral role. In this
role undirected advertising will be enabled and operations not allowed
in Peripheral role (such as scanning and initiating connections) will be
disallowed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds missing feature test macros needed for various use cases
and also sorts the macros according to the feature bit location in the
feature mask (for easy lookup).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds the reading of the LE advertising channel TX power to
the HCI init sequence of LE-capable controllers. This data will be used
e.g. for inclusion in the advertising data packets when advertising is
enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Channel moves are triggered by changes to the BT_CHANNEL_POLICY
sockopt when an ERTM or streaming-mode channel is connected.
Moves are only started if enable_hs is true.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg