This fixes an oops on unbind / module unload (on the musb omap2430
platform).
musb_remove function now calls musb_platform_exit before disabling
runtime pm.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It really should be DEVICE_ATTR_WO(), no need to "open code" it.
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_RW() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fd ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e18 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5d
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f9546 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5d ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e18 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the DA8xx, USB and CPPI 4.1 are sharing the same interrupt line.
Update the driver to request a shared irq.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add code comment to make it clear that the fall-through is intentional.
Read the link for more details: https://lkml.org/lkml/2017/2/9/292
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing musb host mode cable plugging on a BeagleBone, I came across this
error:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd1dcfc60
...
[<bf668390>] (musb_default_readb [musb_hdrc]) from [<bf668578>] (musb_irq_work+0x1c/0x180 [musb_hdrc])
[<bf668578>] (musb_irq_work [musb_hdrc]) from [<c0156554>] (process_one_work+0x2b4/0x808)
[<c0156554>] (process_one_work) from [<c015767c>] (worker_thread+0x3c/0x550)
[<c015767c>] (worker_thread) from [<c015d568>] (kthread+0x104/0x148)
[<c015d568>] (kthread) from [<c01078d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 467d5c9807 ("usb: musb: Implement session bit based runtime PM for
musb-core") started implementing musb generic runtime PM support by
introducing devctl register session bit based state control.
This caused a regression where if a USB mass storage device is connected
to a USB hub, we can get:
usb 1-1: reset high-speed USB device number 2 using musb-hdrc
usb 1-1: device descriptor read/64, error -71
usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
This is because before the USB storage device is connected, musb is
in OTG_STATE_A_SUSPEND. And we currently only set need_finish_resume
in musb_stage0_irq() and the related code calling finish_resume_work
in musb_resume() and musb_runtime_resume() never gets called.
To fix the issue, we can call schedule_delayed_work() directly in
musb_stage0_irq() to have finish_resume_work run.
And we should no longer never get interrupts when when suspended.
We have changed musb to no longer need pm_runtime_irqsafe().
The need_finish_resume flag was added in commit 9298b4aad3 ("usb:
musb: fix device hotplug behind hub") and no longer applies as far
as I can tell. So let's just remove the earlier code that no longer
is needed.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the function musb_get_mode() to get the DT property "dr_mode"
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: David Lechner <david@lechnology.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain on -EPROBE_DEFER when initializing controller,
the driver probe will be retried later.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove comments about resume signalling being stopped from
GetPortStatus, something which is no longer the case.
Fixes: 8ed1fb790e ("usb: musb: finish suspend/reset work...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a USB hub disconnected, devctl can be 0x19 for about a second
on am335x and will stay forever on at least omap3. And we get no
further interrupts when devctl session bit clears. This keeps
PM runtime active.
Let's fix the issue by polling devctl until the session bit clears
or times out. We can do this by making musb->irq_work into
delayed_work.
And with the polling implemented, we can now also have the quirk
for invalid VBUS it to avoid disconnecting too early while VBUS
is ramping up.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime
PM for musb-core")
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer
that runs in softirq context. That causes a "BUG: sleeping function called
from invalid context" every time when polling the cable status:
[<c015ebb4>] (__might_sleep) from [<c0413d60>] (__pm_runtime_resume+0x9c/0xa0)
[<c0413d60>] (__pm_runtime_resume) from [<c04d0bc4>] (otg_timer+0x3c/0x254)
[<c04d0bc4>] (otg_timer) from [<c0191180>] (call_timer_fn+0xfc/0x41c)
[<c0191180>] (call_timer_fn) from [<c01915c0>] (expire_timers+0x120/0x210)
[<c01915c0>] (expire_timers) from [<c0191acc>] (run_timer_softirq+0xa4/0xdc)
[<c0191acc>] (run_timer_softirq) from [<c010168c>] (__do_softirq+0x12c/0x594)
I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled.
And looks like also musb_gadget_queue() suffers from the same problem.
Let's fix the issue by using a list of delayed work then call it on
resume. Note that we want to do this only when musb core and it's
parent devices are awake, and we need to make sure the DSPS glue
timer is stopped as noted by Johan Hovold <johan@kernel.org>.
Note that we already are re-enabling the timer with mod_timer() in
dsps_musb_enable().
Later on we may be able to remove other delayed work in the musb driver
and just do it from pending_resume_work. But this should be done only
for delayed work that does not have other timing requirements beyond
just being run on resume.
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer")
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use static variable first for checking when musb is
initialized when we have multiple musb instances like on am335x.
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the session bit based PM runtime working on musb, we've
implemented few quirks to attempt to detect the current state of
the hardware. One of the quirks is for invalid VBUS as peripheral,
but it is not working in all cases.
If we start musb on dm3730 as a peripheral with no cable connected,
we will get the devctl 91 state once and will never idle as there
are not further interrupts from musb. So we need to ignore the first
devctl 91 state as there will be more interrupts if we're connected.
The invalid VBUS state also can happen always when connected to
certain USB hubs. Looks like musb on dm3730 can claim invalid VBUS
with some hubs while 3717-evm and BeagleBone don't. This causes
session as peripheral to fail for dm3730 with some hubs.
This too is fixed by ignoring only the first invalid VBUS. When
connected, we can just look at the session bit as that will clear
automatically when the session ends.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aDate is always the empty string, so entirely pointless. The aRevision
formatting might as well be done as part of the pr_debug() call - that
also avoids it altogether if pr_debug is compiled out.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to keep musb enabled always when the session bit is
set. This simplifies the PM runtime and allows making it more
generic across the various glue layers.
So far the only exception to just following the session bit is
host mode disconnect where the session bit stays set.
In that case, just allow PM and let the PM runtime autoidle
timeout deal with it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: changed using dev_dbg() to musb_dbg()]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to dump musb interrupt events.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to musb register read/write wrappers to get
trace log for register access.
The default tacepoint log prefix here would be musb_readX/writeX(),
which is not much helpful. So this patch let the tracepoints use
__buildin_return_address(0) to print the caller funciton name to
provide more context of the register access.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.
Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.
Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_hdrc_platform_data::config was defined as a non-const pointer.
However some drivers (e.g. the ux500) set up this pointer to point to a
static structure, which is potentially dangerous. Since the musb core
uses the pointer in a read-only manner the const qualifier was added to
protect the content of the config.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The phy's init routine must be called before it can be used. Do so in
musb_init_controller and the matching shutdown in musb_remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.
Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.
And now we can now also get rid of the include/linux/musb-omap.h.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Merlijn Wajer