'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This file is entirely pseries specific nowadays, so move it out
of arch/powerpc/kernel where it doesn't belong anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With OPAL v3 we can return secondary CPUs to firmware on kexec. This
allows firmware to do various cleanups making things generally more
reliable, and will enable the "new" kernel to call OPAL to perform
some reconfiguration tasks early on that can only be done while
all the CPUs are in firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As suggested by paulus we can simplify the Data Stream Control Register
(DSCR) Facility Status and Control Register (FSCR) handling.
Firstly, we simplify the asm by using a rldimi.
Secondly, we now use the FSCR only to control the DSCR facility, rather
than both the FSCR and HFSCR. Users will see no functional change from
this but will get a minor speedup as they will trap into the kernel only
once (rather than twice) when they first touch the DSCR. Also, this
changes removes a bunch of ugly FTR_SECTION code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Calls to dlpar_detach_node do not iterate over child nodes detaching them as
well. By iterating and detaching the child nodes we ensure that they have the
OF_DETACHED flag set and that their reference counts are decremented such that
the node will be freed from memory by of_node_release.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The node to be detached is retrieved via its phandle by a call to
of_find_node_by_phandle which increments the ref count. We need a matching
call to of_node_put to decrement the ref count and ensure the node is
actually freed.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the device nodes created in the device subtree returned by a call to
dlpar_configure_connector are all named in the root node. This is because the
the node name in the work area returned by ibm,configure-connector rtas call
only contains the node name and not the entire node path. Passing the parent
node where the new subtree will be created to dlpar_configure_connector allows
the correct node path to be prefixed in the full_name field.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the OF_DYNAMIC and kref initialization for a node happens in
dlpar_attach_node. However, a node passed to dlpar_attach_node may be a tree
containing child nodes, and no initialization traversal is done on the
tree. Since the children never get their kref initialized or the OF_DYNAMIC
flag set these nodes are prevented from ever being released from memory
should they become detached. This initialization step is better done at the
time each node is allocated in dlpar_parse_cc_node.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On the first call to ibm,update-properties for a node the first property
returned is the full node path. Currently this is not parsed correctly by the
update_dt_node function. Commit 2e9b7b0 attempted to fix this, but was
incorrect as it made a wrong assumption about the layout of the first
property in the work area. Further, if ibm,update-properties must be called
multiple times for the same node this special property should only be skipped
after the initial call. The first property descriptor returned consists of
the property name, property value length, and property value. The property
name is an empty string, property length is encoded in 4 byte integer, and
the property value is the node path.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The work area buffer returned by the ibm,update-properties rtas call contains
20 bytes of header information prior to the property value descriptor data.
Currently update_dt_node tries to advance over this header using sizeof(upwa).
The update_props_workarea struct contains 20 bytes worth of fields, that map
to the relevant header data, but the sizeof the structure is 24 bytes due to
4 bytes of padding at the end of the structure. Packing the structure ensures
that we don't advance too far over the rtas buffer.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The rc variable is initially used to store the return code from the
ibm,update-properties rtas call which returns 0 or 1 on success. A return
code of 1 indicates that ibm,update-properties must be called again for the
node. However, the rc variable is overwritten by a call to update_dt_prop
which returns 0 on success. This results in ibm,update-properties not being
called again for the given node when the rtas call rc was previously 1.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The update_dt_prop helper function fails to set the IN/OUT parameter prop to
NULL after a complete property has been parsed from the work area returned by
the ibm,update-properties rtas function. This results in the property list of
the device node being updated is corrupted and becomes a loop since the same
property structure is used repeatedly.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the program check handler we handle some causes with interrupts off
and others with interrupts on.
We need to enable interrupts to handle the emulation cases, because they
access userspace memory and might sleep.
For faults in the kernel we don't want to do any emulation, and
emulate_instruction() enforces that. do_mathemu() doesn't but probably
should.
The other disadvantage of enabling interrupts for kernel faults is that
we may take another interrupt, and recurse. As seen below:
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dc10] 0000000000000000 (unreliable)
[c000000fb185dc80] c0000000007d8558 .program_check_exception+0x298/0x2d0
[c000000fb185dd00] c000000000002f40 emulation_assist_common+0x140/0x180
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dff0] 00000000008b9190 (unreliable)
[c000000fb185e060] c0000000007d8558 .program_check_exception+0x298/0x2d0
So avoid both problems by checking if the fault was in the kernel and
skipping the enable of interrupts and the emulation. Go straight to
delivering the SIGILL, which for kernel faults calls die() and so on,
dropping us in the debugger etc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes back traces and profiles easier to read.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The symbols that name some of our exception trampolines are ahead of the
location they name. In most cases this is OK because the code is tightly
packed, but in some cases it means the symbol floats ahead of the
correct location, eg:
c000000000000ea0 <performance_monitor_pSeries_1>:
...
c000000000000f00: 7d b2 43 a6 mtsprg 2,r13
Fix them all by moving the symbol after the set of the location.
While we're moving them anyway, rename them to loose the camelcase and
to make it clear that they are trampolines.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We haven't updated these for a while it seems, it's nice to have in the
oops output.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The spec says it "may be problematic" if CPU x registers the VPA of
CPU y. Add a warning in case we ever do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The VSX alignment handler needs to write out the existing VSX
state to memory before operating on it (flush_vsx_to_thread()).
If we take a VSX alignment exception in the kernel bad things
will happen. It looks like we could write the kernel state out
to the user process, or we could handle the kernel exception
using data from the user process (depending if MSR_VSX is set
or not).
Worse still, if the code to read or write the VSX state causes an
alignment exception, we will recurse forever. I ended up with
hundreds of megabytes of kernel stack to look through as a result.
Floating point and SPE code have similar issues but already include
a user check. Add the same check to emulate_vsx().
With this patch any unaligned VSX loads and stores in the kernel
will show up as a clear oops rather than silent corruption of
kernel or userspace VSX state, or worse, corruption of a potentially
unlimited amount of kernel memory.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a part of pseries_idle backend driver cleanup to make
the code common to both pseries and powernv platforms, it
is necessary to move the backend-driver code to drivers/cpuidle.
As a pre-requisite for that, it is essential to move plpar_wrapper.h
to include/asm.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a part of pseries_idle cleanup to make the backend driver
code common to both pseries and powernv.
Remove non-essential smt_snooze_delay declaration in pseries.h
header file and pseries.h file inclusion in
pseries/processor_idle.c
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The stmw instruction was incorrectly decoded as an update form instruction
and thus the RA register was being clobbered.
Also, the utility routine to write memory to unaligned addresses breaks the
operation into smaller aligned accesses but was incorrectly incrementing
the address by only one; it needs to increment the address by the size of
the smaller aligned chunk.
Signed-off-by: Tom Musta <tmusta@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Memory I/O resources need to be marked as busy or else we cannot remove
them when doing memory hot remove.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVM uses anon_inode_get() to allocate file descriptors as part
of some of its ioctls. But those ioctls are lacking a flag argument
allowing userspace to choose options for the newly opened file descriptor.
In such case it's advised to use O_CLOEXEC by default so that
userspace is allowed to choose, without race, if the file descriptor
is going to be inherited across exec().
This patch set O_CLOEXEC flag on all file descriptors created
with anon_inode_getfd() to not leak file descriptors across exec().
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://lkml.kernel.org/r/cover.1377372576.git.ydroneaud@opteya.com
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
C293PCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add device tree for SEC 6.0 used on C29x silicon.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update the 64-bit hibernation code to support Book E CPUs.
Some registers and instructions are not defined for Book3e
(SDR reg, tlbia instruction).
SDR: Storage Description Register. Book3S and Book3E have different
address translation mode, we do not need HTABORG & HTABSIZE to
translate virtual address to real address.
More registers are saved in BookE-64bit.(TCR, SPRG1)
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add this file to help detect cpu type in runtime.
These macros will be more favorable for driver
to apply errata and workaround to specified cpu type.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
prepare C preprocessor support when processing MPC512x DTS files
- switch from DTS syntax to CPP syntax for include specs
- create a symlink such that DTS processing can reference includes
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
reword the clock control module's registers declaration such that the
MCLK related registers form an array and get indexed by PSC controller
or CAN controller component number
this change is in preparation to COMMON_CLK support for the MPC512x
platform, the changed declaration remains neutral to existing code since
the PSC and MSCAN CCR fields declared here aren't referenced elsewhere
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 40b313608a ("Finally eradicate
CONFIG_HOTPLUG") removed remaining references to CONFIG_HOTPLUG, but missed
a few plain English references in the CONFIG_KEXEC help texts.
Remove them, too.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ve9i
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch moves the generalized implementation of of_get_cpu_node from
PowerPC to DT core library, thereby adding support for retrieving cpu
node for a given logical cpu index on any architecture.
The CPU subsystem can now use this function to assign of_node in the
cpu device while registering CPUs.
It is recommended to use these helper function only in pre-SMP/early
initialisation stages to retrieve CPU device node pointers in logical
ordering. Once the cpu devices are registered, it can be retrieved easily
from cpu device of_node which avoids unnecessary parsing and matching.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Currently different drivers requiring to access cpu device node are
parsing the device tree themselves. Since the ordering in the DT need
not match the logical cpu ordering, the parsing logic needs to consider
that. However, this has resulted in lots of code duplication and in some
cases even incorrect logic.
It's better to consolidate them by adding support for getting cpu
device node for a given logical cpu index in DT core library. However
logical to physical index mapping can be architecture specific.
PowerPC has it's own implementation to get the cpu node for a given
logical index.
This patch refactors the current implementation of of_get_cpu_node.
This in preparation to move the implementation to DT core library.
It separates out the logical to physical mapping so that a default
matching of the physical id to the logical cpu index can be added
when moved to common code. Architecture specific code can override it.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Unlike 64-bit, we don't currently support multiplatform between e500
and non-e500, so the -mcpu is not configurable at this time.
-msoft-float is specified when testing for -mcpu=8540 because otherwise
some older toolchains will fail with "error: E500 and FPRs not
supported".
Signed-off-by: Scott Wood <scottwood@freescale.com>
By default use -mcpu=powerpc64 rather than -mtune=power7
Add options for e5500/e6500, with fallbacks for older compilers.
Hide the POWER cpu options in booke configs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This caused lwsync to be converted to sync on 64-bit (on 32-bit lwsync
is generated at runtime, and so wasn't affected). Not using lwsync
caused a significant slowdown on certain workloads.
Setting this flag for any e500-enabled build is also not friendly to
multiplatform kernels.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some CPUs (such as e500v1/v2) don't implement mftb and will take a
trap. mfspr should work on everything that has a timebase, and is the
preferred instruction according to ISA v2.06.
Currently we get away with mftb on 85xx because the assembler converts
it to mfspr due to -Wa,-me500. However, that flag has other effects
that are undesireable for certain targets (e.g. lwsync is converted to
sync), and is hostile to multiplatform kernels. Thus we would like to
stop setting it for all e500-family builds.
mftb/mftbu instances which are in 85xx code or common code are
converted. Instances which will never run on 85xx are left alone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Erratum A-006598 says that 64-bit mftb is not atomic -- it's subject
to a similar race condition as doing mftbu/mftbl on 32-bit. The lower
half of timebase is updated before the upper half; thus, we can share
the workaround for a similar bug on Cell. This workaround involves
looping if the lower half of timebase is zero, thus avoiding the need
for a scratch register (other than CR0). This workaround must be
avoided when the timebase is frozen, such as during the timebase sync
code.
This deals with kernel and vdso accesses, but other userspace accesses
will of course need to be fixed elsewhere.
Signed-off-by: Scott Wood <scottwood@freescale.com>
If data returned from pstore is compressed, nvram's write callback
will add a flag ERR_TYPE_KERNEL_PANIC_GZ indicating the data is compressed
while writing to nvram. If the data read from nvram is compressed, nvram's
read callback will set the flag 'compressed'. The patch adds backward
compatibilty with old format oops header when reading from pstore.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Backends will set the flag 'compressed' after reading the log from
persistent store to indicate the data being returned to pstore is
compressed or not.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Addition of new argument 'compressed' in the write call back will
help the backend to know if the data passed from pstore is compressed
or not (In case where compression fails.). If compressed, the backend
can add a tag indicating the data is compressed while writing to
persistent store.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
(De)compression support is provided in pstore in subsequent patches which
needs an additional argument 'compressed' to determine if the data
is compressed or not. This patch will take care of removing (de)compression
in nvram with pstore which was making use of 'hsize' argument in pstore write
as 'hsize' will be removed in the subsequent patch.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When reworking udbg_16550.c I forgot to remove the old and now useless
code for the CONFIG_PPC_EARLY_DEBUG_WSP case, which doesn't build as
a result. I also missed a cast.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSCDSjAAoJEHm+PkMAQRiGDXMIAI7Loae0Oqb1eoeJkvjyZsBS
OJDeeEcn+k58VbxVHyRdc7hGo4yI4tUZm172SpnOaM8sZ/ehPU7zBrwJK2lzX334
/jAM3uvVPfxA2nu0I4paNpkED/NQ8NRRsYE1iTE8dzHXOH6dA3mgp5qfco50rQvx
rvseXpME4KIAJEq4jnyFZF5+nuHiPueM9JftPmSSmJJ3/KY9kY1LESovyWd7ttg1
jYSVPFal9J0E+tl2UQY5g9H16GqhhjYn+39Iei6Q5P4bL4ZubQgTRQTN9nyDc06Z
ezQtGoqZ8kEz/2SyRlkda6PzjSEhgXlc8mCL5J7AW+dMhTHHx2IrosjiCA80kG8=
=c0rK
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc5' into perf/core
Merge Linux 3.11-rc5, to sync up with the latest upstream fixes since -rc1.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull nohz improvements from Frederic Weisbecker:
" It mostly contains fixes and full dynticks off-case optimizations. I believe that
distros want to enable this feature so it seems important to optimize the case
where the "nohz_full=" parameter is empty. ie: I'm trying to remove any performance
regression that comes with NO_HZ_FULL=y when the feature is not used.
This patchset improves the current situation a lot (off-case appears to be around 11% faster
with hackbench, although I guess it may vary depending on the configuration but it should be
significantly faster in any case) now there is still some work to do: I can still observe a
remaining loss of 1.6% throughput seen with hackbench compared to CONFIG_NO_HZ_FULL=n. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the arch overrides some generic vtime APIs, let it describe
these on a dedicated and standalone header. This way it becomes
convenient to include it in vtime generic headers without irrelevant
stuff in such a low level header.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Following is a brief description of the PAMU hardware:
PAMU determines what action to take and whether to authorize the action on
the basis of the memory address, a Logical IO Device Number (LIODN), and
PAACT table (logically) indexed by LIODN and address. Hardware devices which
need to access memory must provide an LIODN in addition to the memory address.
Peripheral Access Authorization and Control Tables (PAACTs) are the primary
data structures used by PAMU. A PAACT is a table of peripheral access
authorization and control entries (PAACE).Each PAACE defines the range of
I/O bus address space that is accessible by the LIOD and the associated access
capabilities.
There are two types of PAACTs: primary PAACT (PPAACT) and secondary PAACT
(SPAACT).A given physical I/O device may be able to act as one or more
independent logical I/O devices (LIODs). Each such logical I/O device is
assigned an identifier called logical I/O device number (LIODN). A LIODN is
allocated a contiguous portion of the I/O bus address space called the DSA window
for performing DSA operations. The DSA window may optionally be divided into
multiple sub-windows, each of which may be used to map to a region in system
storage space. The first sub-window is referred to as the primary sub-window
and the remaining are called secondary sub-windows.
This patch provides the PAMU driver (fsl_pamu.c) and the corresponding IOMMU
API implementation (fsl_pamu_domain.c). The PAMU hardware driver (fsl_pamu.c)
has been derived from the work done by Ashish Kalra and Timur Tabi.
[For iommu group support]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Added the following domain attributes for the FSL PAMU driver:
1. Added new iommu stash attribute, which allows setting of the
LIODN specific stash id parameter through IOMMU API.
2. Added an attribute for enabling/disabling DMA to a particular
memory window.
3. Added domain attribute to check for PAMUV1 specific constraints.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add an iommu domain pointer to device (powerpc) archdata. Devices
are attached to iommu domains and this pointer provides a mechanism
to correlate between a device and the associated iommu domain. This
field is set when a device is attached to a domain.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Our ppc64 spinlocks and rwlocks use a trick where a lock token and
the paca index are placed in the lock with a single store. Since we
are using two u16s they need adjusting for little endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to set ELF_DATA correctly on LE coredumps.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add little endian support for demuxing SMP IPIs
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Alistair noticed we got a SIGILL on userspace mfpvr instructions.
Remove the little endian check in the emulation code, it is
probably there to protect against the old pseudo little endian
implementations but doesn't make sense for real little endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lppaca, slb_shadow and dtl_entry hypervisor structures are
big endian, so we have to byte swap them in little endian builds.
LE KVM hosts will also need to be fixed but for now add an #error
to remind us.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add endian annotation to various hypervisor structures which
are defined as big endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The device tree is big endian so make sure we byteswap on little
endian. We assume any pHyp calls also return big endian results in
memory.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We pass dma_window to of_parse_dma_window as a void * and then
run through hoops to cast it back to a u32 array. In the process
we lose endian annotation.
Simplify it by just passing a __be32 * down.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS expects arguments in the call buffer to be big endian so we
need to byteswap on little endian builds
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerPC the device tree is always big endian, but the CPU could be
either, so add be32_to_cpu where appropriate and change the types of
device tree data to __be32 etc to allow sparse to locate endian issues.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we have MMU on exceptions (POWER8) and a relocatable kernel, we
need to branch from the initial exception vectors at 0x0 to up high
where the kernel might be located. Currently we do this using the link
register.
Unfortunately this corrupts the link stack and instead we should use the
count register. We did this for the syscall entry path in:
6a40480 powerpc: Avoid link stack corruption in MMU on syscall entry path
but I stupidly forgot to do the same for other exceptions.
This patch changes the initial exception vectors to use the count
register instead of the link register when we need to branch up to the
relocated kernel.
I have a dodgy userspace test which loops calling a function that reads
the PVR (mfpvr in userspace will be emulated by the kernel via the
program check exception). On POWER8 and with CONFIG_RELOCATABLE=y, I
get a ~10% performance improvement with my userspace test with this
patch.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So far "/sys/devices/system/cpu/cpuX/topology/physical_package_id"
was always default (-1) on ppc64 architecture.
Now, some systems have an ibm,chip-id property in the cpu nodes in
the device tree. On these systems, we now use this information to
display physical_package_id.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
changes for V4:
- changes the type of frozen_pe_no from %d to %llu
in pr_devel()
'pe_no' hasn't been defined, it should be an typo error,
it should be 'frozen_pe_no'.
Also '__func__' has missed in IODA_EEH_DBG(),
For safety reasons, use pr_devel() directly, instead
of use IODA_EEH_DBG()
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit c8db32c866.
The commit breaks the build of all my 64-bit embedded configs. It
looks like gcc-4.7.3 doesn't know about e5500. Additionally it
incorrectly does -mcpu=e5500 on a config that has both e5500 and A2
support enabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Some systems have an ibm,chip-id property in the cpu nodes in the
device tree. On these systems, we now use that to compute the
cpu_core_mask (i.e. the set of core siblings) rather than looking
at cache properties.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Tested-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This factors out the details of updating cpu_core_mask into a separate
function, to make it easier to change how the mask is calculated later.
This makes no functional change.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The denormalized exception handler (denorm_exception_hv) has a couple
of bugs. If the CONFIG_PPC_DENORMALISATION option is not selected,
or the HSRR1_DENORM bit is not set in HSRR1, we don't test whether the
interrupt occurred within a KVM guest. On the other hand, if the
HSRR1_DENORM bit is set and CONFIG_PPC_DENORMALISATION is enabled,
we corrupt the CFAR and PPR.
To correct these problems, this replaces the open-coded version of
EXCEPTION_PROLOG_1 that is there currently, and that is missing the
saving of PPR and CFAR values to the PACA, with an instance of
EXCEPTION_PROLOG_1. This adds an explicit KVMTEST after testing
whether the exception is one we can handle, and adds code to restore
the CFAR on exit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is another file we can generate so add it to the list.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Load/store indexed instructions where the index register RA=R0, such
as "lfdx f1,0,r3", are not illegal.
Load/store indexed with update instructions where the index register
RA=R0, such as "lfdux f1,0,r3", are invalid, and, to be consistent
with existing math-emu behavior for other invalid instruction forms,
will signal as illegal.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of implementing an empty giveup_fpu() function for each
32bit processor type, replace them with an unique empty inline
function.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the current kernel, the function flush_fp_to_thread() is not
dependent on CONFIG_PPC_FPU. So most invocations of this function
is not wrapped by CONFIG_PPC_FPU. Even through we don't really
save the FPRs to the thread struct if CONFIG_PPC_FPU is not enabled,
but there does have some runtime overhead such as the check for
tsk->thread.regs and preempt disable and enable. It really make
no sense to do that. So make it a nop when CONFIG_PPC_FPU is
disabled. Also remove the wrapped #ifdef CONFIG_PPC_FPU
when invoking this function.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit c6e6771b(powerpc: Introduce VSX thread_struct and CONFIG_VSX)
we add a invocation of flush_fp_to_thread() before copying the FPR or
VSR to users. But we already invoke the flush_fp_to_thread() in this
function. So remove one of them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have split the math emulation into two parts. This makes it
possible to just emulate the unimplemented floating point instructions
on these boards.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only using of function disable_kernel_fp() was already dropped
in the commit 5daf9071 (powerpc: merge align.c).
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For some SoC (such as the FSL BookE) even though there does have
a hardware FPU, but not all floating point instructions are
implemented. Unfortunately some versions of gcc do use these
unimplemented instructions. Then we have to enable the math emulation
to workaround this issue. It seems a little redundant to have the
support to emulate all the floating point instructions in this case.
So split the math emulation into two parts. One is for the SoC which
doesn't have FPU at all and the other for the SoC which does have the
hardware FPU and only need some special floating point instructions to
be emulated.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are two invocations of do_mathemu() in traps.c. And the codes
in these two places are almost the same. Introduce a locale function
to eliminate the duplication. With this change we can also make sure
that in program_check_exception() the PPC_WARN_EMULATED is invoked for
the correctly emulated math instructions.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By doing this we can make sure that the FPU state is only flushed to
the thread struct when it is really needed.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I got the following error on my t4240qds board.
ntpd[2713]: unhandled signal 4 at 0fd5b448 nip 0fd5b448 lr 0fd5b424 code 30001
The root cause is that the float point instruction 'fsqrt' is used.
But this instruction is not implemented on e6500 core. Even this
does seem a gcc bug, I would like to enable the math emulation
in the kernel to workaround this kind of issue.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Kconfig symbol 8XX_MINIMAL_FPEMU was removed in commit 968219fa33
("powerpc/8xx: Remove 8xx specific "minimal FPU emulation""). But that
commit didn't remove all code depending on that symbol. Do so now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The math.c is only built when CONFIG_MATH_EMULATION is enabled.
So the #ifdef check for CONFIG_MATH_EMULATION in it seems redundant.
Drop all of them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The math.c is only built when CONFIG_MATH_EMULATION is enabled.
So we would never get into the case that CONFIG_MATH_EMULATION
is not defined in this file.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Legacy UARTs can exist on PowerNV, memory-mapped ones on PCI
or IO based ones on the LPC bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some machines might provide the console via a different mechanism
such as direct access to a UART from Linux, in which case OPAL
might not expose any console. In that case, the code would cause
a NULL dereference.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The udbg_16550 code, which we use for our early consoles and debug
backends was fairly messy. Especially for the debug consoles, it
would re-implement the "high level" getc/putc/poll functions for
each access method. It also had code to configure the UART but only
for the straight MMIO method.
This changes it to instead abstract at the register accessor level,
and have the various functions and configuration routines use these.
The result is simpler and slightly smaller code, and free support
for non-MMIO mapped PIO UARTs, which such as the ones that can be
present on a POWER 8 LPC bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses the hooks provided by CONFIG_PPC_INDIRECT_PIO to
implement a set of hooks for IO port access to use the LPC
bus via OPAL calls for the first 64K of IO space
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the generic PPC_INDIRECT_IO and ensure we only add overhead
to the right accessors. IE. If only CONFIG_PPC_INDIRECT_PIO is set,
we don't add overhead to all MMIO accessors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The SOFT_DISABLE_INTS seems an odd name for something that updates the
software state to be consistent with interrupts being hard disabled, so
rename SOFT_DISABLE_INTS with RECONCILE_IRQ_STATE to avoid this confusion.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a bunch of CONFIG_PPC_EARLY_DEBUG_* options that are intended
for bringup/debug only. They hard wire a machine specific udbg backend
very early on (before we even probe the platform), and use whatever
tricks are available on each machine/cpu to be able to get some kind
of output out there early on.
So far, on powermac with no serial ports, we have CONFIG_PPC_EARLY_DEBUG_BOOTX
to use the low-level btext engine on the screen, but it doesn't do much, at
least on 64-bit. It only really gets enabled after the platform has been
probed and the MMU enabled.
This adds a way to enable it much earlier. From prom_init.c (while still
running with Open Firmware), we grab the screen details and set things up
using the physical address of the frame buffer.
Then btext itself uses the "rm_ci" feature of the 970 processor (Real
Mode Cache Inhibited) to access it while in real mode.
We need to do a little bit of reorg of the btext code to inline things
better, in order to limit how much we touch memory while in this mode as
the consequences might be ... interesting.
This successfully allowed me to debug problems early on with the G5
(related to gold being broken vs. ppc64 kernels).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_read_bridge_bases() already checks if the PCI bus is root
bus or not, so we needn't do same check in pcibios_fixup_bus()
and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PHB3 doesn't support IO ports and we needn't IO segment map for that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The index of one specific PCI controller (struct pci_controller::
global_number) can tell that it's primary one or not. So we needn't
additional variable for that and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch enables fetching bus range from device-tree for the
specific PHB. If we can't get that from device-tree, the default
range [0 255] will be used.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't free PHB instance (struct pnv_phb) on error to creating
the associated PCI controler (struct pci_controller). The patch
fixes that. Also, the output messages have been cleaned for a bit
so that they looks unified for IODA_1/2 cases.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since 2002, the kernel has not saved VRSAVE on exception entry and
restored it on exit; rather, VRSAVE gets context-switched in _switch.
This means that when executing in process context in the kernel, the
userspace VRSAVE value is live in the VRSAVE register.
However, the signal code assumes that current->thread.vrsave holds
the current VRSAVE value, which is incorrect. Therefore, this
commit changes it to use the actual VRSAVE register instead. (It
still uses current->thread.vrsave as a temporary location to store
it in, as __get_user and __put_user can only transfer to/from a
variable, not an SPR.)
This also modifies the transactional memory code to save and restore
VRSAVE regardless of whether VMX is enabled in the MSR. This is
because accesses to VRSAVE are not controlled by the MSR.VEC bit,
but can happen at any time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Other architectures have a __get_user_pages_fast(), in addition to the
regular get_user_pages_fast(), which doesn't call get_user_pages() on
failure, and thus doesn't attempt to fault pages in or COW them. The
generic KVM code uses __get_user_pages_fast() to detect whether a page
for which we have only requested read access is actually writable.
This provides an implementation of __get_user_pages_fast() by
splitting the existing get_user_pages_fast() in two. With this, the
generic KVM code will get the right answer instead of always
considering such pages non-writable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
T4, Cell, powernv, and pseries had the same implementation, so switch
them to use a generic version. A2 apparently had a version, but
removed it at some point, so we remove the declaration, too.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cell and PSeries both implemented their own versions of a
cpu_bootable smp_op which do the same thing (well, the PSeries
one has support for more than 2 threads). Copy the PSeries one
to generic code, and rename it smp_generic_cpu_bootable.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
And now the function flush_icache_range() is just a wrapper which
only invoke the function __flush_icache_range() directly. So we
don't have reason to keep it anymore.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In function flush_icache_range(), we use cpu_has_feature() to test
the feature bit of CPU_FTR_COHERENT_ICACHE. But this seems not optimal
for two reasons:
a) For ppc32, the function __flush_icache_range() already do this
check with the macro END_FTR_SECTION_IFSET.
b) Compare with the cpu_has_feature(), the method of using macro
END_FTR_SECTION_IFSET will not introduce any runtime overhead.
[And while at it, add the missing required isync] -- BenH
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although the shared_proc field in the lppaca works today, it is
not architected. A shared processor partition will always have a non
zero yield_count so use that instead. Create a wrapper so users
don't have to know about the details.
In order for older kernels to continue to work on KVM we need
to set the shared_proc bit. While here, remove the ugly bitfield.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix a sparse warning about force_32bit_msi being a one bit bitfield.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
plpar_get_term_char is only used once and just adds a layer
of complexity to H_GET_TERM_CHAR. plpar_put_term_char isn't
used at all so we can remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simplify things by putting all the 32bit and 64bit defines
together instead of in two spots.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We always use VMX loads and stores to manage the high 32
VSRs. Remove these unused macros.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Not having parentheses around a macro is asking for trouble.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Normally when we haven't implemented an alignment handler for
a load or store instruction the process will be terminated.
The alignment handler uses the DSISR (or a pseudo one) to locate
the right handler. Unfortunately ldbrx and stdbrx overlap lfs and
stfs so we incorrectly think ldbrx is an lfs and stdbrx is an
stfs.
This bug is particularly nasty - instead of terminating the
process we apply an incorrect fixup and continue on.
With more and more overlapping instructions we should stop
creating a pseudo DSISR and index using the instruction directly,
but for now add a special case to catch ldbrx/stdbrx.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
p_toc is an 8 byte relative offset to the TOC that we place in the
text section. This means it is only 4 byte aligned where it should
be 8 byte aligned. Add an explicit alignment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
My gcc-4.3.5 fails to compile due to:
|cc1: warnings being treated as errors
|arch/powerpc/platforms/52xx/mpc52xx_pic.c: In function ‘mpc52xx_irqhost_map’:
|arch/powerpc/platforms/52xx/mpc52xx_pic.c:343: error: ‘irqchip’ may be used uninitialized in this function
since commit e34298c ("powerpc: 52xx: nop out unsupported critical
IRQs"). This warning is complete crap since only values 0…3 are possible
which are checked but gcc fails to understand that. I wouldn't care much
but since this is compiled with -Werror I made this patch.
While add it, I replaced the warning from l2irq to l1irq since this is
the number that is evaluated.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Now that we have weak versions for each of the PCI MSI architecture
functions, we can actually build the MSI support for all platforms,
regardless of whether they provide or not architecture-specific
versions of those functions. For this reason, the ARCH_SUPPORTS_MSI
hidden kconfig boolean becomes useless, and this patch gets rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Until now, the MSI architecture-specific functions could be overloaded
using a fairly complex set of #define and compile-time
conditionals. In order to prepare for the introduction of the msi_chip
infrastructure, it is desirable to switch all those functions to use
the 'weak' mechanism. This commit converts all the architectures that
were overidding those MSI functions to use the new strategy.
Note that we keep two separate, non-weak, functions
default_teardown_msi_irqs() and default_restore_msi_irqs() for the
default behavior of the arch_teardown_msi_irqs() and
arch_restore_msi_irqs(), as the default behavior is needed by x86 PCI
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If a transaction is rolled back, the Target Address Register (TAR), Processor
Priority Register (PPR) and Data Stream Control Register (DSCR) should be
restored to the checkpointed values before the transaction began. Any changes
to these SPRs inside the transaction should not be visible in the abort
handler.
Currently Linux doesn't save or restore the checkpointed TAR, PPR or DSCR. If
we preempt a processes inside a transaction which has modified any of these, on
process restore, that same transaction may be aborted we but we won't see the
checkpointed versions of these SPRs.
This adds checkpointed versions of these SPRs to the thread_struct and adds the
save/restore of these three SPRs to the treclaim/trechkpt code.
Without this if any of these SPRs are modified during a transaction, users may
incorrectly see a speculated SPR value even if the transaction is aborted.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves us to save the Target Address Register (TAR) a earlier in
__switch_to. It introduces a new function save_tar() to do this.
We need to save the TAR earlier as we will overwrite it in the transactional
memory reclaim/recheckpoint path. We are going to do this in a subsequent
patch which will fix saving the TAR register when it's modified inside a
transaction.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8 allows the DSCR to be accessed directly from userspace via a new SPR
number 0x3 (Rather than 0x11. DSCR SPR number 0x11 is still used on POWER8 but
like POWER7, is only accessible in HV and OS modes). Currently, we allow this
by setting H/FSCR DSCR bit on boot.
Unfortunately this doesn't work, as the kernel needs to see the DSCR change so
that it knows to no longer restore the system wide version of DSCR on context
switch (ie. to set thread.dscr_inherit).
This clears the H/FSCR DSCR bit initially. If a process then accesses the DSCR
(via SPR 0x3), it'll trap into the kernel where we set thread.dscr_inherit in
facility_unavailable_exception().
We also change _switch() so that we set or clear the H/FSCR DSCR bit based on
the thread.dscr_inherit.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reworks the Facility Status and Control Regsiter (FSCR) config bit
definitions so that we can access the bit numbers. This is needed for a
subsequent patch to fix the userspace DSCR handling.
HFSCR and FSCR bit definitions are the same, so reuse them.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if we take hypervisor facility unavaliable (from 0xf80/0x4f80) we
mark it as an OS facility unavaliable (0xf60) as the two share the same code
path.
The becomes a problem in facility_unavailable_exception() as we aren't able to
see the hypervisor facility unavailable exceptions.
Below fixes this by duplication the required macros.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
err was overwritten by a previous function call, and checked to be 0. If
the following page allocation fails, 0 is going to be returned instead
of -ENOMEM.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The procfs entry for global statistics has been missed on PowerNV
platform and the patch is going to add that.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Older kernels has just length information in their header. Handle it
while reading old kernel oops log from pstore.
Applies on top of powerpc/pseries: Fix buffer overflow when reading from pstore
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When reading from pstore there is a buffer overflow during decompression
due to the header added in unzip_oops. Remove unzip_oops and call
pstore_decompress directly in nvram_pstore_read. Allocate buffer of size
report_length of the oops header as header will not be deallocated in pstore.
Since we have 'openssl' command line tool to decompress the compressed data,
dump the compressed data in case decompression fails instead of not dumping
anything.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want PPC_DENORMALISATION enabled when POWERNV is enabled,
so update the Kconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
If CONFIG_E500 is enabled, the compilation flags are updated
specifying the target core -mcpu=e5500/e500mc/8540
Also remove -Wa,-me500, being incompatible with -mcpu=e5500/e6500
The assembler option is redundant if the -mcpu= flag is set.
The patch fixes the kernel compilation problem for e5500/e6500
when using gcc option -mcpu=e5500/e6500.
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When using recent udev, the /dev node mount requires CONFIG_DEVTMPFS_MOUNT
is enabled in Kernel. The patch enables the option in defconfig of Freescale
QorIQ targets.
Changed defconfig list:
arch/powerpc/configs/85xx/p1023rds_defconfig
arch/powerpc/configs/corenet32_smp_defconfig
arch/powerpc/configs/corenet64_smp_defconfig
arch/powerpc/configs/mpc85xx_smp_defconfig
arch/powerpc/configs/mpc85xx_defconfig
arch/powerpc/configs/mpc83xx_defconfig
Signed-off-by: Zhenhua Luo <zhenhua.luo@freescale.com>
[scottwood@freescale.com: added mpc83xx and non-smp mpc85xx]
Signed-off-by: Scott Wood <scottwood@freescale.com>
For Freescale powerpc platform, the PCI-e bus number uses the reassign mode
by default. It means the second PCI-e controller's hose->first_busno is the
first controller's last bus number adding 1. For some hotpluged device(or
controlled by FPGA), the device is linked to PCI-e slot at linux runtime.
It needs rescan for the system to add it and driver it to work. It successes
to rescan the device linked to the first PCI-e controller's slot, but fails to
rescan the device linked to the second PCI-e controller's slot. The cause is
that the bus->number is reset to 0, which isn't equal to the hose->first_busno
for the second controller checking PCI-e link. So it doesn't really check the
PCI-e link status, the link status is always no_link. The device won't be
really rescaned. Reset the bus->number to hose->first_busno in the function
fsl_pcie_check_link(), it will do the real checking PCI-e link status for the
second controller, the device will be rescaned.
Signed-off-by: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This function contains all the stuff we need to check if SWIOTLB
should be enabled or not. So it is more convenient to enable
the SWIOTLB here than later.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The (1ull << mem_log) is never greater than mem unless mem_log++;
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The function pci_devs_phb_init is invoked more earlier than we really
probe the pci controller, so it does nothing at all. And we also don't
need the pci_dn stuff for the fsl powerpc64 boards, just remove it.
It also seems that we don't support ISA on all the current corenet ds
boards. So picking a primary bus seems useless, remove that function
too.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
The p1020rdb-pd has the similar feature as the p1020rdb.
Therefore, p1020rdb-pd use the same platform file as the p1/p2 rdb board.
Overview of P1020RDB-PD platform:
- DDR3 2GB
- NOR flash 64MB
- NAND flash 128MB
- SPI flash 16MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
At console init, when the kernel tries to flush the log buffer
the ePAPR byte-channel based console write fails silently,
losing the buffered messages.
This happens because The ePAPR para-virtualization init isn't
done early enough so that the hcall instruction to be set,
causing the byte-channel write hcall to be a nop.
To fix, change the ePAPR para-virt init to use early device
tree functions and move it in early init.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The original MPIC MSI bank contains 8 registers, MPIC v4.3 MSI bank
contains 16 registers, and this patch adds NR_MSI_REG_MAX and
NR_MSI_IRQS_MAX to describe the maximum capability of MSI bank.
MPIC v4.3 provides MSIIR1 to index these 16 MSI registers. MSIIR1
uses different bits definition than MSIIR. This patch adds
ibs_shift and srs_shift to indicate the bits definition of the
MSIIR and MSIIR1, so the same code can handle the MSIIR and MSIIR1
simultaneously.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[scottwood@freescale.com: reinstated static on all_avail]
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the latest platform T4 and B4, MPIC controller has been updated
to v4.3. This patch adds a new file to describe the latest MPIC.
The MSI blocks number is increased to four, the registers number
of each block is increased to sixteen. MSIIR1 has been added to
access these sixteen MSI registers.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mpic_get_primary_version() is not defined when not using MPIC.
The compile error log like:
arch/powerpc/sysdev/built-in.o: In function `fsl_of_msi_probe':
fsl_msi.c:(.text+0x150c): undefined reference to `fsl_mpic_primary_get_version'
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
e6500 core performance monitors has the following features:
- 6 performance monitor counters
- 512 events supported
- no threshold events
e6500 PMU has more specific events (Data L1 cache misses, Instruction L1
cache misses, etc ) than e500 PMU (which only had Data L1 cache reloads,
etc). Where available, the more specific events have been used which will
produce slightly different results than e500 PMU equivalents.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are 6 counters in e6500 core instead of 4 in e500 core.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This change is required after the e6500 perf support has been added.
There are 6 counters in e6500 core instead of 4 in e500 core and
the MAX_HWEVENTS counter should be changed accordingly from 4 to 6.
Added also runtime check for counters overflow.
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This file is a common include for B4860 and B4420 but is not a valid DTS itself:
DTC arch/powerpc/boot/b4qds.dtb
Error: arch/powerpc/boot/dts/b4qds.dts:35.1-2 syntax error
FATAL ERROR: Unable to parse input tree
make[1]: *** [arch/powerpc/boot/b4qds.dtb] Error 1
make: *** [b4qds.dtb] Error 2
I spotted in build tests of device-tree.git, announcement
https://lkml.org/lkml/2013/4/24/209, which builds *.dts. Probably no one would
do this this in real life on linux.git but it still seems worth fixing.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shaveta Leekha <shaveta@freescale.com>
Cc: Minghuan Lian <Minghuan.Lian@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull powerpc fixes from Ben Herrenschmidt:
"Here is not quite a handful of powerpc fixes for rc3.
The windfarm fix is a regression fix (though not a new one), the PMU
interrupt rename is not a fix per-se but has been submitted a long
time ago and I kept forgetting to put it in (it puts us back in sync
with x86), the other perf bit is just about putting an API/ABI bit
definition in the right place for userspace to consume, and finally,
we have a fix for the VPHN (Virtual Partition Home Node) feature
(notification that the hypervisor is moving nodes around) which could
cause lockups so we may as well fix it now"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/windfarm: Fix noisy slots-fan on Xserve (rm31)
powerpc: VPHN topology change updates all siblings
powerpc/perf: Export PERF_EVENT_CONFIG_EBB_SHIFT to userspace
powerpc: Rename PMU interrupts from CNT to PMI
Hotplug
PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device
PCI: hotplug: Convert to be builtin only, not modular
PCI: pciehp: Convert pciehp to be builtin only, not modular
Resource allocation
PCI: Retry allocation of only the resource type that failed
ARM
PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=z2eX
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Yinghai fixed a couple regressions: one resource assignment problem
introduced in v3.10 that showed up with SR-IOV on powerpc, and another
SR-IOV hot-remove issue related to refcounting changes we merged for
v3.11.
Yinghai is still working on another SR-IOV-related fix or two, which
will be simpler if pciehp is non-modular, so I included the Kconfig
changes now to get them in earlier.
Finally, a minor fix for the ARM Marvell EBU host bridge driver that
was merged for v3.11
Hotplug:
PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device
PCI: hotplug: Convert to be builtin only, not modular
PCI: pciehp: Convert pciehp to be builtin only, not modular
Resource allocation:
PCI: Retry allocation of only the resource type that failed
ARM:
PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge"
* tag 'pci-v3.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge
PCI: Retry allocation of only the resource type that failed
PCI: pciehp: Convert pciehp to be builtin only, not modular
PCI: hotplug: Convert to be builtin only, not modular
PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device
When an associativity level change is found for one thread, the
siblings threads need to be updated as well. This is done today
for PRRN in stage_topology_update() but is missing for VPHN in
update_cpu_associativity_changes_mask(). This patch will correctly
update all thread siblings during a topology change.
Without this patch a topology update can result in a CPU in
init_sched_groups_power() getting stuck indefinitely in a loop.
This loop is built in build_sched_groups(). As a result of the thread
moving to a node separate from its siblings the struct sched_group will
have its next pointer set to point to itself rather than the sched_group
struct of the next thread. This happens because we have a domain without
the SD_OVERLAP flag, which is correct, and a topology that doesn't conform
with reality (threads on the same core assigned to different numa nodes).
When this list is traversed by init_sched_groups_power() it will reach
the thread's sched_group structure and loop indefinitely; the cpu will
be stuck at this point.
The bug was exposed when VPHN was enabled in commit b7abef0 (v3.9).
Cc: <stable@vger.kernel.org> [v3.9+]
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use bit 63 of the event code for userspace to request that the event
be counted using EBB (Event Based Branches). Export this value, making
it part of the API - though only on processors that support EBB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Back in commit 89713ed "Add timer, performance monitor and machine check
counts to /proc/interrupts" we added a count of PMU interrupts to the
output of /proc/interrupts.
At the time we named them "CNT" to match x86.
However in commit 89ccf46 "Rename 'performance counter interrupt'", the
x86 guys renamed theirs from "CNT" to "PMI".
Arguably changing the name could break someone's script, but I think the
chance of that is minimal, and it's preferable to have a name that 1) is
somewhat meaningful, and 2) matches x86.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This problem belongs to the core synchronization issues.
The cpu1 already updated spin_table values, but bootcore cannot get
this value in time.
After bootcpu hibiernation restore the pages. we are now running
with the kernel data of the old kernel fully restored. if we reset
the non-bootcpus that will be reset cache(tlb), the non-bootcpus
will get new address(map virtual and physical address spaces).
but bootcpu tlb cache still use boot kernel data, so we need to
invalidate the bootcpu tlb cache make it to get new main memory data.
log:
Enabling non-boot CPUs ...
smp_85xx_kick_cpu: timeout waiting for core 1 to reset
smp: failed starting cpu 1 (rc -2)
Error taking CPU1 up: -2
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
[scottwood@freescale.com: reworded code comment for clarity]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix to return a negative error code in the MSI bitmap alloc error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A PCIe erratum of mpc85xx may causes a core hang when a link of PCIe
goes down. when the link goes down, Non-posted transactions issued
via the ATMU requiring completion result in an instruction stall.
At the same time a machine-check exception is generated to the core
to allow further processing by the handler. We implements the handler
which skips the instruction caused the stall.
This patch depends on patch:
powerpc/85xx: Add platform_device declaration to fsl_pci.h
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <soniccat.liu@gmail.com>
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Opcode and xopcode are useful definitions not just for KVM. Move these
definitions to asm/ppc-opcode.h for public use.
Also add the opcodes for LHAUX and LWZUX.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
[scottwood@freesacle.com: update commit message and rebase]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Convert CONFIG_HOTPLUG_PCI from tristate to bool. This only affects
the hotplug core; several of the hotplug drivers can still be modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Unlike the other general-purpose SPRs, SPRG3 can be read by usermode
code, and is used in recent kernels to store the CPU and NUMA node
numbers so that they can be read by VDSO functions. Thus we need to
load the guest's SPRG3 value into the real SPRG3 register when entering
the guest, and restore the host's value when exiting the guest. We don't
need to save the guest SPRG3 value when exiting the guest as usermode
code can't modify SPRG3.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On some PAE architectures, the entire range of physical memory could reside
outside the 32-bit limit. These systems need the ability to specify the
initrd location using 64-bit numbers.
This patch globally modifies the early_init_dt_setup_initrd_arch() function to
use 64-bit numbers instead of the current unsigned long.
There has been quite a bit of debate about whether to use u64 or phys_addr_t.
It was concluded to stick to u64 to be consistent with rest of the device
tree code. As summarized by Geert, "The address to load the initrd is decided
by the bootloader/user and set at that point later in time. The dtb should not
be tied to the kernel you are booting"
More details on the discussion can be found here:
https://lkml.org/lkml/2013/6/20/690https://lkml.org/lkml/2012/9/13/544
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
When the task moves around the system, the corresponding cpuhw
per cpu strcuture should be popullated with the BHRB filter
request value so that PMU could be configured appropriately with
that during the next call into power_pmu_enable().
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Completely ignore BHRB privilege state filter request as we are
already configuring that with privilege state filtering attribute
for the accompanying PMU event. This would help achieve cleaner
user space interaction for BHRB.
This patch fixes a situation like this
Before patch:-
------------
./perf record -j any -e branch-misses:k ls
Error:
The sys_perf_event_open() syscall returned with 95 (Operation not
supported) for event (branch-misses:k).
/bin/dmesg may provide additional information.
No CONFIG_PERF_EVENTS=y kernel support configured?
Here 'perf record' actually copies over ':k' filter request into BHRB
privilege state filter config and our previous check in kernel would
fail that.
After patch:-
-------------
./perf record -j any -e branch-misses:k ls
perf perf.data perf.data.old test-mmap-ring
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (~102 samples)]
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark pnv_pci_init_ioda2_phb() as __init. It is called only from an
init function (pnv_pci_init()), and it calls an init function
(pnv_pci_init_ioda_phb()):
pnv_pci_init # init
pnv_pci_init_ioda2_phb # non-init
pnv_pci_init_ioda_phb # init
This should fix a section mismatch warning.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sllp value is stored in mmu_psize_defs in such a way that we can easily OR
the value to get the operand for slbmte instruction. ie, the L and LP bits are
not contiguous. Decode the bits and use them correctly in tlbie.
regression is introduced by 1f6aaaccb1
"powerpc: Update tlbie/tlbiel as per ISA doc"
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should not fallthrough different case statements in hpte_decode. Add
break statement to break out of the switch. The regression is introduced by
dcda287a9b "powerpc/mm: Simplify hpte_decode"
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 801eb73f45 introduced
a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag
when __PAGE_NO_CACHE is set and the cache update policy is not write-through
(i.e. _PAGE_WRITETHRU is not set)
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
CC: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.
The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.
The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.
The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.
Most of the generic code already supports that, we just need to
plumb it properly on our side.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we're trasversing the EEH devices list using list_for_each_entry().
That's not safe enough because the EEH devices might be removed from
its parent PE while doing iteration. The patch replaces that with
list_for_each_entry_safe().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we do normal hotplug, the PE (shadow EEH structure) shouldn't be
kept around.
However, we need to keep it if the hotplug an artifial one caused by
EEH errors recovery.
Since we remove EEH device through the PCI hook pcibios_release_device(),
the flag "purge_pe" passed to various functions is meaningless. So the patch
removes the meaningless flag and introduce new flag "EEH_PE_KEEP"
to save the PE while doing hotplug during EEH error recovery.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make some functions public in order to support hotplug on either specific
PCI bus or PCI device in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We will rely on pcibios_release_device() to remove the EEH cache
and unbind EEH device for the specific PCI device. So we shouldn't
hold the reference to the PCI device from EEH cache and EEH device.
Otherwise, pcibios_release_device() won't be called as we expected.
The patch removes the reference to the PCI device in EEH core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During Machine Check interrupt on pseries platform, R3 generally points to
memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS
delivers the machine check exception it passes the address inside FWNMI area
with the top most bit set. This patch fixes this issue by masking top two bit
in machine check exception handler.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The presence or absence of EBB is advertised to userspace via the presence
or absence of PPC_FEATURE2_EBB in cpu_user_features2.
Because the kernel can be built without PMU support, we should only add
PPC_FEATURE2_EBB to cpu_user_features2 when we successfully register the
power8 PMU support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Kconfig symbol HOTPLUG was removed with commit 40b313608a ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In hard_irq_disable(), we accessed the PACA before we hard disabled
the interrupts, potentially causing a warning as get_paca() will
us debug_smp_processor_id().
Move that to after the disabling, and also use local_paca directly
rather than get_paca() to avoid several redundant and useless checks.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Chen Gang