To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
smq seems to be performing better than the old mq policy in all
situations, as well as using a quarter of the memory.
Make 'mq' an alias for 'smq' when choosing a cache policy. The tunables
that were present for the old mq are faked, and have no effect. mq
should be considered deprecated now.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If ignore_zero_blocks is enabled dm-verity will return zeroes for blocks
matching a zero hash without validating the content.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add support for correcting corrupted blocks using Reed-Solomon.
This code uses RS(255, N) interleaved across data and hash
blocks. Each error-correcting block covers N bytes evenly
distributed across the combined total data, so that each byte is a
maximum distance away from the others. This makes it possible to
recover from several consecutive corrupted blocks with relatively
small space overhead.
In addition, using verity hashes to locate erasures nearly doubles
the effectiveness of error correction. Being able to detect
corrupted blocks also improves performance, because only corrupted
blocks need to corrected.
For a 2 GiB partition, RS(255, 253) (two parity bytes for each
253-byte block) can correct up to 16 MiB of consecutive corrupted
blocks if erasures can be located, and 8 MiB if they cannot, with
16 MiB space overhead.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
users (e.g. kvm guests) that issued ioctls when a multipath device had
no available paths.
- Include Christoph's refactoring of DM's ioctl handling and add support
for passing through persistent reservations with DM multipath.
- All other changes are very simple cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOp04AAoJEMUj8QotnQNaFLsH/AhMEH/jI1ObOfy4J1Wy4rOx
ujJT91uS/s0H3pc9cGKQYnuGpFkX6WWU4wMiabIyiTn4sAsoXaflfIGutivLiDJr
HfecrMrGZgnP4ZlpPPB02BmlxFbcPW8yzAU4ma38xBgQ+Pu30RO/HkvX/2vKOppG
qwPop/XsNxq3KXgFGM44ToytM6c/MPGluhuvOwbaacAO1HviMuen9qsVjk4kwcf3
jGYTbEPHATxyu5/6oKDTkQTYhzdwg3B2qHCiKMGw3l1kXhaQLFcaOivOLV8Sf3xh
bj1070pkGe9OpqaVzMnwDtJ8rnsBl/Nt4wj9oiQPxbX71GYZAmcMIYn9WEkcKFI=
=AR2D
-----END PGP SIGNATURE-----
Merge tag 'dm-4.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
"Smaller set of DM changes for this merge. I've based these changes on
Jens' for-4.4/reservations branch because the associated DM changes
required it.
- Revert a dm-multipath change that caused a regression for
unprivledged users (e.g. kvm guests) that issued ioctls when a
multipath device had no available paths.
- Include Christoph's refactoring of DM's ioctl handling and add
support for passing through persistent reservations with DM
multipath.
- All other changes are very simple cleanups"
* tag 'dm-4.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm switch: simplify conditional in alloc_region_table()
dm delay: document that offsets are specified in sectors
dm delay: capitalize the start of an delay_ctr() error message
dm delay: Use DM_MAPIO macros instead of open-coded equivalents
dm linear: remove redundant target name from error messages
dm persistent data: eliminate unnecessary return values
dm: eliminate unused "bioset" process for each bio-based DM device
dm: convert ffs to __ffs
dm: drop NULL test before kmem_cache_destroy() and mempool_destroy()
dm: add support for passing through persistent reservations
dm: refactor ioctl handling
Revert "dm mpath: fix stalls when handling invalid ioctls"
dm: initialize non-blk-mq queue data before queue is used
Only delay params are mentioned in delay.txt.
Mention offsets just like documents for linear and flakey do.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 76c44f6d80 introduced the possibly for "Overflow" to be reported
by the snapshot device's status. Older userspace (e.g. lvm2) does not
handle the "Overflow" status response.
Fix this incompatibility by requiring newer userspace code, that can
cope with "Overflow", request the persistent store with overflow support
by using "PO" (Persistent with Overflow) for the snapshot store type.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Fixes: 76c44f6d80 ("dm snapshot: don't invalidate on-disk image on snapshot write overflow")
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For RAID 4/5/6 data integrity reasons 'discard_zeroes_data' must work
properly.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the user selected the precise_timestamps or histogram options, report
it in the @stats_list message output.
If the user didn't select these options, no extra tokens are reported,
thus it is backward compatible with old software that doesn't know about
precise timestamps and histogram.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.2
There is currently no way to see that the needs_check flag has been set
in the metadata. Display 'needs_check' in the cache status if it is set
in the cache metadata.
Also, update cache documentation.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is currently no way to see that the needs_check flag has been set
in the metadata. Display 'needs_check' in the thin-pool status if it is
set in the thinp metadata.
Also, update thinp documentation.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add an option to dm statistics to collect and report a histogram of
IO latencies.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make it possible to use precise timestamps with nanosecond granularity
in dm statistics.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The Stochastic multiqueue (SMQ) policy (vs MQ) offers the promise of
less memory utilization, improved performance and increased adaptability
in the face of changing workloads. SMQ also does not have any
cumbersome tuning knobs.
Users may switch from "mq" to "smq" simply by appropriately reloading a
DM table that is using the cache target. Doing so will cause all of the
mq policy's hints to be dropped. Also, performance of the cache may
degrade slightly until smq recalculates the origin device's hotspots
that should be cached.
In the future the "mq" policy will just silently make use of "smq" and
the mq code will be removed.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
If a cache metadata operation fails (e.g. transaction commit) the
cache's metadata device will abort the current transaction, set a new
needs_check flag, and the cache will transition to "read-only" mode. If
aborting the transaction or setting the needs_check flag fails the cache
will transition to "fail-io" mode.
Once needs_check is set the cache device will not be allowed to
activate. Activation requires write access to metadata. Future work is
needed to add proper support for running the cache in read-only mode.
Once in fail-io mode the cache will report a status of "Fail".
Also, add commit() wrapper that will disallow commits if in read_only or
fail mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cryptsetup home page moved to GitLab.
Also remove link to abandonded Truecrypt page.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Introduce a new target that is meant for file system developers to test file
system integrity at particular points in the life of a file system. We capture
all write requests and associated data and log them to a separate device
for later replay. There is a userspace utility to do this replay. The
idea behind this is to give file system developers a tool to verify that
the file system is always consistent.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Zach Brown <zab@zabbo.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add device specific modes to dm-verity to specify how corrupted
blocks should be handled. The following modes are defined:
- DM_VERITY_MODE_EIO is the default behavior, where reading a
corrupted block results in -EIO.
- DM_VERITY_MODE_LOGGING only logs corrupted blocks, but does
not block the read.
- DM_VERITY_MODE_RESTART calls kernel_restart when a corrupted
block is discovered.
In addition, each mode sends a uevent to notify userspace of
corruption and to allow further recovery actions.
The driver defaults to previous behavior (DM_VERITY_MODE_EIO)
and other modes can be enabled with an additional parameter to
the verity table.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make it possible to disable offloading writes by setting the optional
'submit_from_crypt_cpus' table argument.
There are some situations where offloading write bios from the
encryption threads to a single thread degrades performance
significantly.
The default is to offload write bios to the same thread because it
benefits CFQ to have writes submitted using the same IO context.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use unbound workqueue by default so that work is automatically balanced
between available CPUs. The original behavior of encrypting using the
same cpu that IO was submitted on can still be enabled by setting the
optional 'same_cpu_crypt' table argument.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Before, if the user wanted sequential IO to be promoted to the cache
they'd have to set sequential_threshold to some nebulous large value.
Now, the user may easily disable sequential IO detection (and sequential
IO's implicit bypass of the cache) by setting sequential_threshold to 0.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than maintaining a separate promote_threshold variable that we
periodically update we now use the hit count of the oldest clean
block. Also add a fudge factor to discourage demoting dirty blocks.
With some tests this has a sizeable difference, because the old code
was too eager to demote blocks. For example, device-mapper-test-suite's
git_extract_cache_quick test goes from taking 190 seconds, to 142
(linear on spindle takes 250).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add support for quickly loading a repetitive pattern into the
dm-switch target.
In the "set_regions_mappings" message, the user may now use "Rn,m" as
one of the arguments. "n" and "m" are hexadecimal numbers. The "Rn,m"
argument repeats the last "n" arguments in the following "m" slots.
For example:
dmsetup message switch 0 set_region_mappings 1000:1 :2 R2,10
is equivalent to
dmsetup message switch 0 set_region_mappings 1000:1 :2 :1 :2 :1 :2 :1 :2 \
:1 :2 :1 :2 :1 :2 :1 :2 :1 :2
Requested-by: Jay Wang <jwang@nimblestorage.com>
Tested-by: Jay Wang <jwang@nimblestorage.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 85ad643b ("dm thin: add timeout to stop out-of-data-space mode
holding IO forever") introduced a fixed 60 second timeout. Users may
want to either disable or modify this timeout.
Allow the out-of-data-space timeout to be configured using the
'no_space_timeout' dm-thin-pool module param. Setting it to 0 will
disable the timeout, resulting in IO being queued until more data space
is added to the thin-pool.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.14+
dm-era is a target that behaves similar to the linear target. In
addition it keeps track of which blocks were written within a user
defined period of time called an 'era'. Each era target instance
maintains the current era as a monotonically increasing 32-bit
counter.
Use cases include tracking changed blocks for backup software, and
partially invalidating the contents of a cache to restore cache
coherency after rolling back a vendor snapshot.
dm-era is primarily expected to be paired with the dm-cache target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The Documentation for the thin provisioning target's held metadata root
feature was incorrect. It is now available and the value for the held
metadata root is in block units (not 512b sectors).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a thin metadata operation fails the current transaction will abort,
whereby causing potential for IO layers up the stack (e.g. filesystems)
to have data loss. As such, set THIN_METADATA_NEEDS_CHECK_FLAG in the
thin metadata's superblock which:
1) requires the user verify the thin metadata is consistent (e.g. use
thin_check, etc)
2) suggests the user verify the thin data is consistent (e.g. use fsck)
The only way to clear the superblock's THIN_METADATA_NEEDS_CHECK_FLAG is
to run thin_repair.
On metadata operation failure: abort current metadata transaction, set
pool in read-only mode, and now set the needs_check flag.
As part of this change, constraints are introduced or relaxed:
* don't allow a pool to transition to write mode if needs_check is set
* don't allow data or metadata space to be resized if needs_check is set
* if a thin pool's metadata space is exhausted: the kernel will now
force the user to take the pool offline for repair before the kernel
will allow the metadata space to be extended.
Also, update Documentation to include information about when the thin
provisioning target commits metadata, how it handles metadata failures
and running out of space.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
The cache's policy may have been established using the "default" alias,
which is currently the "mq" policy but the default policy may change in
the future. It is useful to know exactly which policy is being used.
Add a 'real' member to the dm_cache_policy_type structure and have the
"default" dm_cache_policy_type point to the real "mq"
dm_cache_policy_type. Update dm_cache_policy_get_name() to check if
real is set, if so report the name of the real policy (not the alias).
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Improve cache_status to emit:
<metadata block size> <#used metadata blocks>/<#total metadata blocks>
<cache block size> <#used cache blocks>/<#total cache blocks>
...
Adding the block sizes allows for easier calculation of the overall size
of both the metadata and cache devices. Adding <#total cache blocks>
provides useful context for how much of the cache is used.
Unfortunately these additions to the status will require updates to
users' scripts that monitor the cache status. But these changes help
provide more comprehensive information about the cache device and will
simplify tools that are being developed to manage dm-cache devices --
because they won't need to issue 3 operations to cobble together the
information that we can easily provide via a single status ioctl.
While updating the status documentation in cache.txt spaces were
tabify'd.
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Internally the mq policy maintains a promotion threshold variable. If
the hit count of a block not in the cache goes above this threshold it
gets promoted to the cache.
This patch introduces three new tunables that allow you to tweak the
promotion threshold by adding a small value. These adjustments depend
on the io type:
read_promote_adjustment: READ io, default 4
write_promote_adjustment: WRITE io, default 8
discard_promote_adjustment: READ/WRITE io to a discarded block, default 1
If you're trying to quickly warm a new cache device you may wish to
reduce these to encourage promotion. Remember to switch them back to
their defaults after the cache fills though.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the pool runs out of data or metadata space, the pool can either
queue or error the IO destined to the data device. The default is to
queue the IO until more space is added.
An admin may now configure the pool to error IO when no space is
available by setting the 'error_if_no_space' feature when loading the
thin-pool table.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
The cache target's invalidate_cblocks message allows cache block
(cblock) ranges to be expressed with: <cblock start>-<cblock end>
The range's <cblock end> value is "one past the end", so the range
includes <cblock start> through <cblock end>-1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Document passthrough mode, cache shrinking, and cache invalidation.
Also, use strcasecmp() and hlist_unhashed().
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cache block invalidation is removing an entry from the cache without
writing it back. Cache blocks can be invalidated via the
'invalidate_cblocks' message, which takes an arbitrary number of cblock
ranges:
invalidate_cblocks [<cblock>|<cblock begin>-<cblock end>]*
E.g.
dmsetup message my_cache 0 invalidate_cblocks 2345 3456-4567 5678-6789
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
"Passthrough" is a dm-cache operating mode (like writethrough or
writeback) which is intended to be used when the cache contents are not
known to be coherent with the origin device. It behaves as follows:
* All reads are served from the origin device (all reads miss the cache)
* All writes are forwarded to the origin device; additionally, write
hits cause cache block invalidates
This mode decouples cache coherency checks from cache device creation,
largely to avoid having to perform coherency checks while booting. Boot
scripts can create cache devices in passthrough mode and put them into
service (mount cached filesystems, for example) without having to worry
about coherency. Coherency that exists is maintained, although the
cache will gradually cool as writes take place.
Later, applications can perform coherency checks, the nature of which
will depend on the type of the underlying storage. If coherency can be
verified, the cache device can be transitioned to writethrough or
writeback mode while still warm; otherwise, the cache contents can be
discarded prior to transitioning to the desired operating mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Morgan Mears <Morgan.Mears@netapp.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are now two multiqueues for in cache blocks. A clean one and a
dirty one.
writeback_work comes from the dirty one. Demotions come from the clean
one.
There are two benefits:
- Performance improvement, since demoting a clean block is a noop.
- The cache cleans itself when io load is light.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-crypt can already activate TCRYPT (TrueCrypt compatible) containers
in LRW or XTS block encryption mode.
TCRYPT containers prior to version 4.1 use CBC mode with some additional
tweaks, this patch adds support for these containers.
This new mode is implemented using special IV generator named TCW
(TrueCrypt IV with whitening). TCW IV only supports containers that are
encrypted with one cipher (Tested with AES, Twofish, Serpent, CAST5 and
TripleDES).
While this mode is legacy and is known to be vulnerable to some
watermarking attacks (e.g. revealing of hidden disk existence) it can
still be useful to activate old containers without using 3rd party
software or for independent forensic analysis of such containers.
(Both the userspace and kernel code is an independent implementation
based on the format documentation and it completely avoids use of
original source code.)
The TCW IV generator uses two additional keys: Kw (whitening seed, size
is always 16 bytes - TCW_WHITENING_SIZE) and Kiv (IV seed, size is
always the IV size of the selected cipher). These keys are concatenated
at the end of the main encryption key provided in mapping table.
While whitening is completely independent from IV, it is implemented
inside IV generator for simplification.
The whitening value is always 16 bytes long and is calculated per sector
from provided Kw as initial seed, xored with sector number and mixed
with CRC32 algorithm. Resulting value is xored with ciphertext sector
content.
IV is calculated from the provided Kiv as initial IV seed and xored with
sector number.
Detailed calculation can be found in the Truecrypt documentation for
version < 4.1 and will also be described on dm-crypt site, see:
http://code.google.com/p/cryptsetup/wiki/DMCrypt
The experimental support for activation of these containers is already
present in git devel brach of cryptsetup.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Support the collection of I/O statistics on user-defined regions of
a DM device. If no regions are defined no statistics are collected so
there isn't any performance impact. Only bio-based DM devices are
currently supported.
Each user-defined region specifies a starting sector, length and step.
Individual statistics will be collected for each step-sized area within
the range specified.
The I/O statistics counters for each step-sized area of a region are
in the same format as /sys/block/*/stat or /proc/diskstats but extra
counters (12 and 13) are provided: total time spent reading and
writing in milliseconds. All these counters may be accessed by sending
the @stats_print message to the appropriate DM device via dmsetup.
The creation of DM statistics will allocate memory via kmalloc or
fallback to using vmalloc space. At most, 1/4 of the overall system
memory may be allocated by DM statistics. The admin can see how much
memory is used by reading
/sys/module/dm_mod/parameters/stats_current_allocated_bytes
See Documentation/device-mapper/statistics.txt for more details.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Inform users that the data block size can't be any arbitrary number,
i.e. its value must be between 64KB and 1GB. Also, it should be a
multiple of 64KB.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Place upper bound on the cache's data block size (1GB).
Inform users that the data block size can't be any arbitrary number,
i.e. its value must be between 32KB and 1GB. Also, it should be a
multiple of 32KB.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
A cache's metadata device may not be shared by multiple cache devices.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s5m4
-----END PGP SIGNATURE-----
Merge tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Add a device-mapper target called dm-switch to provide a multipath
framework for storage arrays that dynamically reconfigure their
preferred paths for different device regions.
Fix a bug in the verity target that prevented its use with some
specific sizes of devices.
Improve some locking mechanisms in the device-mapper core and bufio.
Add Mike Snitzer as a device-mapper maintainer.
A few more clean-ups and fixes"
* tag 'dm-3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: add switch target
dm: update maintainers
dm: optimize reorder structure
dm: optimize use SRCU and RCU
dm bufio: submit writes outside lock
dm cache: fix arm link errors with inline
dm verity: use __ffs and __fls
dm flakey: correct ctr alloc failure mesg
dm verity: remove pointless comparison
dm: use __GFP_HIGHMEM in __vmalloc
dm verity: fix inability to use a few specific devices sizes
dm ioctl: set noio flag to avoid __vmalloc deadlock
dm mpath: fix ioctl deadlock when no paths
dm-switch is a new target that maps IO to underlying block devices
efficiently when there is a large number of fixed-sized address regions
but there is no simple pattern to allow for a compact mapping
representation such as dm-stripe.
Though we have developed this target for a specific storage device, Dell
EqualLogic, we have made an effort to keep it as general purpose as
possible in the hope that others may benefit.
Originally developed by Jim Ramsay. Simplified by Mikulas Patocka.
Signed-off-by: Jim Ramsay <jim_ramsay@dell.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
MD: Remember the last sync operation that was performed
This patch adds a field to the mddev structure to track the last
sync operation that was performed. This is especially useful when
it comes to what is recorded in mismatch_cnt in sysfs. If the
last operation was "data-check", then it reports the number of
descrepancies found by the user-initiated check. If it was a
"repair" operation, then it is reporting the number of
descrepancies repaired. etc.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add message/status support for changing sync action
This patch adds a message interface to dm-raid to allow the user to more
finely control the sync actions being performed by the MD driver. This
gives the user the ability to initiate "check" and "repair" (i.e. scrubbing).
Two additional fields have been appended to the status output to provide more
information about the type of sync action occurring and the results of those
actions, specifically: <sync_action> and <mismatch_cnt>. These new fields
will always be populated. This is essentially the device-mapper way of doing
what MD controls through the 'sync_action' sysfs file and shows through the
'mismatch_cnt' sysfs file.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly
improves the number of sets of devices that can concurrently
fail, without data loss.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=YdVD
-----END PGP SIGNATURE-----
Merge tag 'md-3.9' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"Mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly improves the
number of sets of devices that can concurrently fail, without data
loss."
* tag 'md-3.9' of git://neil.brown.name/md:
md: expedite metadata update when switching read-auto -> active
md: remove CONFIG_MULTICORE_RAID456
md/raid1,raid10: fix deadlock with freeze_array()
md/raid0: improve error message when converting RAID4-with-spares to RAID0
md: raid0: fix error return from create_stripe_zones.
md: fix two bugs when attempting to resize RAID0 array.
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 1)
MD RAID10: Minor non-functional code changes
md: raid1,10: Handle REQ_WRITE_SAME flag in write bios
md: protect against crash upon fsync on ro array
A simple cache policy that writes back all data to the origin.
This is used to decommission a dm cache by emptying it.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A cache policy that uses a multiqueue ordered by recent hit
count to select which blocks should be promoted and demoted.
This is meant to be a general purpose policy. It prioritises
reads over writes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a target that allows a fast device such as an SSD to be used as a
cache for a slower device such as a disk.
A plug-in architecture was chosen so that the decisions about which data
to migrate and when are delegated to interchangeable tunable policy
modules. The first general purpose module we have developed, called
"mq" (multiqueue), follows in the next patch. Other modules are
under development.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
Until now, dm-raid.c only supported the "near" algorthm of MD's RAID10
implementation. This patch adds support for the "far" and "offset"
algorithms, but only with the improved redundancy that is brought with
the introduction of the 'use_far_sets' bit, which shifts copied stripes
according to smaller sets vs the entire array. That is, the 17th bit
of the 'layout' variable that defines the RAID10 implementation will
always be set. (More information on how the 'layout' variable selects
the RAID10 algorithm can be found in the opening comments of
drivers/md/raid10.c.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Before attempting to activate a RAID array, it is checked for sufficient
redundancy. That is, we make sure that there are not too many failed
devices - or devices specified for rebuild - to undermine our ability to
activate the array. The current code performs this check twice - once to
ensure there were not too many devices specified for rebuild by the user
('validate_rebuild_devices') and again after possibly experiencing a failure
to read the superblock ('analyse_superblocks'). Neither of these checks are
sufficient. The first check is done properly but with insufficient
information about the possible failure state of the devices to make a good
determination if the array can be activated. The second check is simply
done wrong in the case of RAID10 because it doesn't account for the
independence of the stripes (i.e. mirror sets). The solution is to use the
properly written check ('validate_rebuild_devices'), but perform the check
after the superblocks have been read and we know which devices have failed.
This gives us one check instead of two and performs it in a location where
it can be done right.
Only RAID10 was affected and it was affected in the following ways:
- the code did not properly catch the condition where a user specified
a device for rebuild that already had a failed device in the same mirror
set. (This condition would, however, be caught at a deeper level in MD.)
- the code triggers a false positive and denies activation when devices in
independent mirror sets have failed - counting the failures as though they
were all in the same set.
The most likely place this error was introduced (or this patch should have
been included) is in commit 4ec1e369 - first introduced in v3.7-rc1.
Consequently this fix should also go in v3.7.y, however there is a
small conflict on the .version in raid_target, so I'll submit a
separate patch to -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add code to validate replacement slots for RAID10 arrays
RAID10 can handle 'copies - 1' failures for each mirror group. This code
ensures the user has provided a valid array - one whose devices specified for
rebuild do not exceed the amount of redundancy available.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull md updates from NeilBrown.
* 'for-next' of git://neil.brown.name/md:
DM RAID: Add support for MD RAID10
md/RAID1: Add missing case for attempting to repair known bad blocks.
md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE.
md/raid1: don't abort a resync on the first badblock.
md: remove duplicated test on ->openers when calling do_md_stop()
raid5: Add R5_ReadNoMerge flag which prevent bio from merging at block layer
md/raid1: prevent merging too large request
md/raid1: read balance chooses idlest disk for SSD
md/raid1: make sequential read detection per disk based
MD RAID10: Export md_raid10_congested
MD: Move macros from raid1*.h to raid1*.c
MD RAID1: rename mirror_info structure
MD RAID10: rename mirror_info structure
MD RAID10: Fix compiler warning.
raid5: add a per-stripe lock
raid5: remove unnecessary bitmap write optimization
raid5: lockless access raid5 overrided bi_phys_segments
raid5: reduce chance release_stripe() taking device_lock
Add read-only and fail-io modes to thin provisioning.
If a transaction commit fails the pool's metadata device will transition
to "read-only" mode. If a commit fails once already in read-only mode
the transition to "fail-io" mode occurs.
Once in fail-io mode the pool and all associated thin devices will
report a status of "Fail".
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support non-power-of-2 chunk sizes with dm striping for proper alignment
of stripe IO on storage that has non-power-of-2 optimal IO sizes (e.g.
RAID6 10+2).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-stripe is supposed to ensure that all the space allocated to the
stripes is fully used and that all stripes are the same size. This
patch fixes the test. It checks that device length is divisible by the
chunk size and checks that the resulting quotient is divisible by the
number of stripes (which is equivalent to testing if device length is
divisible by chunk_size * stripes).
Previously, the code only tested that the number of sectors in the target
was divisible by each of the chunk size and the number of stripes
separately, which could leave entire stripes unused.
(A setup that genuinely needs some stripes to be shorter than others
can be created by concatenating striped targets.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Veritysetup is now part of cryptsetup package.
Remove on-disk header description (which is not parsed in kernel)
and point users to cryptsetup where it the format is documented.
Mention units for block size paramaters.
Fix target line specification and dmsetup parameters.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This device-mapper target creates a read-only device that transparently
validates the data on one underlying device against a pre-generated tree
of cryptographic checksums stored on a second device.
Two checksum device formats are supported: version 0 which is already
shipping in Chromium OS and version 1 which incorporates some
improvements.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Elly Jones <ellyjones@chromium.org>
Cc: Milan Broz <mbroz@redhat.com>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm thin target arguments to control discard support.
ignore_discard: Disables discard support
no_discard_passdown: Don't pass discards down to the underlying data
device, but just remove the mapping within the thin provisioning target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the use of an external _read only_ device as an origin for a thin
device.
Any read to an unprovisioned area of the thin device will be passed
through to the origin. Writes trigger allocation of new blocks as
usual.
One possible use case for this would be VM hosts that want to run
guests on thinly-provisioned volumes but have the base image on another
device (possibly shared between many VMs).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The thin metadata format can only make use of a device that is <=
THIN_METADATA_MAX_SECTORS (currently 15.9375 GB). Therefore, there is no
practical benefit to using a larger device.
However, it may be that other factors impose a certain granularity for
the space that is allocated to a device (E.g. lvm2 can impose a coarse
granularity through the use of large, >= 1 GB, physical extents).
Rather than reject a larger metadata device, during thin-pool device
construction, switch to allowing it but issue a warning if a device
larger than THIN_METADATA_MAX_SECTORS_WARNING (16 GB) is
provided. Any space over 15.9375 GB will not be used.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove documentation for unimplemented 'trim' message.
I'd planned a 'trim' target message for shrinking thin devices, but
this is better handled via the discard ioctl.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix comments: clustered-disk needs a hyphen not an underscore.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Initial EXPERIMENTAL implementation of device-mapper thin provisioning
with snapshot support. The 'thin' target is used to create instances of
the virtual devices that are hosted in the 'thin-pool' target. The
thin-pool target provides data sharing among devices. This sharing is
made possible using the persistent-data library in the previous patch.
The main highlight of this implementation, compared to the previous
implementation of snapshots, is that it allows many virtual devices to
be stored on the same data volume, simplifying administration and
allowing sharing of data between volumes (thus reducing disk usage).
Another big feature is support for arbitrary depth of recursive
snapshots (snapshots of snapshots of snapshots ...). The previous
implementation of snapshots did this by chaining together lookup tables,
and so performance was O(depth). This new implementation uses a single
data structure so we don't get this degradation with depth.
For further information and examples of how to use this, please read
Documentation/device-mapper/thin-provisioning.txt
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The persistent-data library offers a re-usable framework for the storage
and management of on-disk metadata in device-mapper targets.
It's used by the thin-provisioning target in the next patch and in an
upcoming hierarchical storage target.
For further information, please read
Documentation/device-mapper/persistent-data.txt
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add optional parameter field to dmcrypt table and support
"allow_discards" option.
Discard requests bypass crypt queue processing. Bio is simple remapped
to underlying device.
Note that discard will be never enabled by default because of security
consequences. It is up to the administrator to enable it for encrypted
devices.
(Note that userspace cryptsetup does not understand new optional
parameters yet. Support for this will come later. Until then, you
should use 'dmsetup' to enable and disable this.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the ability to parse and use metadata devices to dm-raid. Although
not strictly required, without the metadata devices, many features of
RAID are unavailable. They are used to store a superblock and bitmap.
The role, or position in the array, of each device must be recorded in
its superblock. This is to help with fault handling, array reshaping,
and sanity checks. RAID 4/5/6 devices must be loaded in a specific order:
in this way, the 'array_position' field helps validate the correctness
of the mapping when it is loaded. It can be used during reshaping to
identify which devices are added/removed. Fault handling is impossible
without this field. For example, when a device fails it is recorded in
the superblock. If this is a RAID1 device and the offending device is
removed from the array, there must be a way during subsequent array
assembly to determine that the failed device was the one removed. This
is done by correlating the 'array_position' field and the bit-field
variable 'failed_devices'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the write_mostly parameter to RAID1 dm-raid tables.
This allows the user to set the WriteMostly flag on a RAID1 device that
should normally be avoided for read I/O.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the user to specify the region_size.
Ensures that the supplied value meets md's constraints, viz. the number of
regions does not exceed 2^21.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add more information about some dm-raid table parameters and clarify how
parameters are printed when 'dmsetup table' is issued.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add corrupt_bio_byte feature to simulate corruption by overwriting a byte at a
specified position with a specified value during intervals when the device is
"down".
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add 'drop_writes' option to drop writes silently while the
device is 'down'. Reads are not touched.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This target is the same as the linear target except that it returns I/O
errors periodically. It's been found useful in simulating failing
devices for testing purposes.
I needed a dm target to do some failure testing on btrfs's raid code, and
Mike pointed me at this.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds generic multikey handling to be used
in following patch for Loop-AES mode compatibility.
This patch extends mapping table to optional keycount and
implements generic multi-key capability.
With more keys defined the <key> string is divided into
several <keycount> sections and these are used for tfms.
The tfm is used according to sector offset
(sector 0->tfm[0], sector 1->tfm[1], sector N->tfm[N modulo keycount])
(only power of two values supported for keycount here).
Because of tfms per-cpu allocation, this mode can be take
a lot of memory on large smp systems.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Max Vozeler <max@hinterhof.net>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update Documentation/device-mapper/snapshot.txt to cover "How to
determine when a snapshot has finished merging".
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The snapshot-merge target allows a snapshot to be merged back into the
snapshot's origin device.
One anticipated use of snapshot merging is the rollback of filesystems
to back out problematic system upgrades.
This patch adds snapshot-merge target management to both
dm_snapshot_init() and dm_snapshot_exit(). As an initial place-holder,
snapshot-merge is identical to the snapshot target. Documentation is
provided.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch contains a device-mapper mirror log module that forwards
requests to userspace for processing.
The structures used for communication between kernel and userspace are
located in include/linux/dm-log-userspace.h. Due to the frequency,
diversity, and 2-way communication nature of the exchanges between
kernel and userspace, 'connector' was chosen as the interface for
communication.
The first log implementations written in userspace - "clustered-disk"
and "clustered-core" - support clustered shared storage. A userspace
daemon (in the LVM2 source code repository) uses openAIS/corosync to
process requests in an ordered fashion with the rest of the nodes in the
cluster so as to prevent log state corruption. Other implementations
with no association to LVM or openAIS/corosync, are certainly possible.
(Imagine if two machines are writing to the same region of a mirror.
They would both mark the region dirty, but you need a cluster-aware
entity that can handle properly marking the region clean when they are
done. Otherwise, you might clear the region when the first machine is
done, not the second.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a service time oriented dynamic load balancer,
dm-service-time, which selects the path with the shortest estimated
service time for the incoming I/O.
The service time is estimated by dividing the in-flight I/O size
by a performance value of each path.
The performance value can be given as a table argument at the table
loading time. If no performance value is given, all paths are
considered equal.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a dynamic load balancer, dm-queue-length, which
balances the number of in-flight I/Os across the paths.
The code is based on the patch posted by Stefan Bader:
https://www.redhat.com/archives/dm-devel/2005-October/msg00050.html
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add description of dm-crypt to device-mapper documentation.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds support for the dm_path_event dm_send_event functions which
create and send udev events.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
New device-mapper target that can delay I/O (for testing). Reads can be
separated from writes, redirected to different underlying devices and delayed
by differing amounts of time.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Christie