Fix the code to fetch and decode the whole 32-bit instruction. This
only really matters with the `noulri' kernel parameter as all microMIPS
processors are supposed to have all the hardware registers we support.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the regular MIPS instruction set RDHWR is encoded with the SPECIAL3
(011111) major opcode. Therefore it cannot trigger the CpU (Coprocessor
Unusable) exception, and certainly not for coprocessor 0, as the opcode
does not overlap with any of the older ISA reservations, i.e. LWC0
(110000), SWC0 (111000), LDC0 (110100) or SDC0 (111100). The closest
match might be SDC3 (111111), possibly causing a CpU #3 exception,
however our code does not handle it anyway. A quick check with a MIPS I
and a MIPS III processor:
CPU0 revision is: 00000220 (R3000)
CPU0 revision is: 00000440 (R4400SC)
indeed indicates that the RI (Reserved Instruction) exception is
triggered. It's only LL and SC that require emulation in the CpU #0
exception handler as they reuse the LWC0 and SWC0 opcodes respectively.
In the microMIPS instruction set RDHWR is mandatory and triggering the
RI exception is required on unimplemented or disabled register accesses.
Therefore emulating the microMIPS instruction in the CpU #0 exception
handler is not required either.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
start_thread() (called for execve(2)) clears the TIF_USEDFPU flag
without atomically disabling the FPU. With a preemptive kernel, an
unfortunately timed preemption after this could result in another
task (or KVM guest) being scheduled in with the FPU still enabled, since
lose_fpu_inatomic() only turns it off if TIF_USEDFPU is set.
Use lose_fpu(0) instead of the separate FPU / MSA management, which
should do the right thing (drop FPU properly and atomically without
saving state) and will be more future proof.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set IORESOURCE_SYSTEM_RAM in flags of resource ranges with
"System RAM", "Kernel code", "Kernel data", and "Kernel bss".
Note that:
- IORESOURCE_SYSRAM (i.e. modifier bit) is set in flags when
IORESOURCE_MEM is already set. IORESOURCE_SYSTEM_RAM is defined
as (IORESOURCE_MEM|IORESOURCE_SYSRAM).
- Some archs do not set 'flags' for children nodes, such as
"Kernel code". This patch does not change 'flags' in this
case.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1453841853-11383-7-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
The first argument to set_except_vector is the ExcCode, which we now
have definitions for. Lets make use of them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11894/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c5a ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: 40e084a506 ("MIPS: Add uprobes support.")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11920/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the CONFIG_MIPS_CMDLINE_EXTEND to CONFIG_MIPS_CMDLINE_DTB_EXTEND
to resolve the EXTEND_WITH_PROM macro.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Fixes: 2024972ef5 ("MIPS: Make the kernel arguments from dtb available")
Reviewed-by: Alexander Sverdlin <alexander.svedlin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11909/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently assumes that a core will start up in legacy mode
using the exception base provided through the CM GCR registers. If a
core has been configured in hardware to start in EVA mode, these
assumptions will fail.
This patch ensures that secondary cores are initialized to meet these
assumptions.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While synchronization, count register will go backwards for the master.
If synchronise_count_master() runs before synchronise_count_slave(),
skew becomes even more. The skew is very harmful for CPU hotplug (CPU0
do synchronization with CPU1, then CPU0 do synchronization with CPU2
and CPU0's count goes backwards, so it will be out of sync with CPU1).
After the commit cf9bfe55f2 (MIPS: Synchronize MIPS count one
CPU at a time), we needn't evaluate count_reference at the beginning of
synchronise_count_master() any more. Thus, we evaluate the initcount (It
seems like count_reference is redundant) in the 2nd loop. Since we write
the count register in the last loop, we don't need additional barriers
(the existing memory barriers are enough).
Moreover, I think we loop 3 times is enough to get a primed instruction
cache, this can also get less skew than looping 5 times.
Comments are also updated in this patch.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/12163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add an `ieee754=' kernel parameter to control IEEE Std 754 conformance
mode.
Use separate flags copied from the respective CPU feature flags, and
adjusted according to the conformance mode selected, to make binaries
requesting individual NaN encoding modes accepted or rejected as needed.
Update the initial setting for FCSR and, in the full FPU emulation mode,
its read-only mask accordingly. Accept the mode selection requested for
legacy processors as well.
As with the EF_MIPS_NAN2008 ELF file header flag adjust both ABS2008 and
NAN2008 bits at the same time, to match the choice made for hardware
currently implemented.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11481/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Determine the presence of and the amount of control available over IEEE
Std 754-2008 features.
In the case of a hardware FPU being used examine the FIR register for
the presence of the HAS2008 bit and then the FCSR register for the
writability of the ABS2008 and NAN2008 bits and the hardwired state of
each of these bits if read-only. Update the initial FCSR contents used
for threads and the FCSR writability mask accordingly.
For full FPU emulation and MIPS32 or MIPS64 processors make the FCSR
ABS2008 and NAN2008 bits writable.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11480/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Handle the EF_MIPS_NAN2008 ELF file header flag and refuse execution
where there is no support in the FPU for the NaN encoding mode requested
by a binary invoked. Ensure that the setting of the bit in the binary
matches one in any intepreter used. Set the thread's initial FCSR
contents according to the value of the EF_MIPS_NAN2008.
Set the values of the FCSR ABS2008 and NAN2008 bits both to the same
value if possible, to take the approach taken with existing FPU hardware
into account. As of now all implementations have both bits hardwired to
the same value, that is both are fixed at 0 or both are fixed at 1, even
though the architecture allows for implementations where the amount of
control implemented with each of these two individual bits is
independent of each other.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11479/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also pass any interpreter's file header to `arch_check_elf' so that any
architecture handler can have a look at it if needed.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement IEEE Std 754-2008 NaN encoding wired to the state of the
FCSR.NAN2008 bit. Make the interpretation of the quiet bit in NaN data
as follows:
* in the legacy mode originally defined by the MIPS architecture the
value of 1 denotes an sNaN whereas the value of 0 denotes a qNaN,
* in the 2008 mode introduced with revision 5 of the MIPS architecture
the value of 0 denotes an sNaN whereas the value of 1 denotes a qNaN,
following the definition of the preferred NaN encoding introduced with
IEEE Std 754-2008.
In the 2008 mode, following the requirement of the said standard, quiet
an sNaN where needed by setting the quiet bit to 1 and leaving all the
NaN payload bits unchanged.
Update format conversion operations according to the rules set by IEEE
Std 754-2008 and the MIPS architecture. Specifically:
* propagate NaN payload bits through conversions between floating-point
formats such that as much information as possible is preserved and
specifically a conversion from a narrower format to a wider format and
then back to the original format does not change a qNaN payload in any
way,
* conversions from a floating-point to an integer format where the
source is a NaN, infinity or a value that would convert to an integer
outside the range of the result format produce, under the default
exception handling, the respective values defined by the MIPS
architecture.
In full FPU emulation set the FIR.HAS2008 bit to 1, however do not make
any further FCSR bits writable.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11477/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allocate CPU option bits and define macros for the legacy-NaN and
2008-NaN IEEE Std 754 MIPS architecture features. Unconditionally mark
the legacy-NaN feature as present across hardware and emulated
floating-point configurations.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rewrite `arch_elf_pt_proc' and `arch_check_elf' using a union to access
the ELF file header.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11474/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull livepatching updates from Jiri Kosina:
- RO/NX attribute fixes for patch module relocations from Josh
Poimboeuf. As part of this effort, module.c has been cleaned up as
well and livepatching is piggy-backing on this cleanup. Rusty is OK
with this whole lot going through livepatching tree.
- symbol disambiguation support from Chris J Arges. That series is
also
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
but this came in only after I've alredy pushed out. Didn't want to
rebase because of that, hence I am mentioning it here.
- symbol lookup fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Cleanup module page permission changes
module: keep percpu symbols in module's symtab
module: clean up RO/NX handling.
module: use a structure to encapsulate layout.
gcov: use within_module() helper.
module: Use the same logic for setting and unsetting RO/NX
livepatch: function,sympos scheme in livepatch sysfs directory
livepatch: add sympos as disambiguator field to klp_reloc
livepatch: add old_sympos as disambiguator field to klp_func
Commit 977e043d5e ("MIPS: kernel: cps-vec: Replace mips32r2 ISA level
with mips64r2") leads to .set mips64r2 directives being present in 32
bit (ie. CONFIG_32BIT=y) kernels. This is incorrect & leads to MIPS64
instructions being emitted by the assembler when expanding
pseudo-instructions. For example the "move" instruction can legitimately
be expanded to a "daddu". This causes problems when the kernel is run on
a MIPS32 CPU, as CONFIG_32BIT kernels of course often are...
Fix this by dropping the .set <ISA> directives entirely now that Kconfig
should be ensuring that kernels including this code are built with a
suitable -march= compiler flag.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__clear_user() (and clear_user() which uses it), always access the user
mode address space, which results in EVA store instructions when EVA is
enabled even if the current user address limit is KERNEL_DS.
Fix this by adding a new symbol __bzero_kernel for the normal kernel
address space bzero in EVA mode, and call that from __clear_user() if
eva_kernel_access().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Makes it easier to handle init vs core cleanly, though the change is
fairly invasive across random architectures.
It simplifies the rbtree code immediately, however, while keeping the
core data together in the same cachline (now iff the rbtree code is
enabled).
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
While the 5KE processors have never been taped out, they exists though
a CP0.PRId and experimental RTLs or QEMU implementations. Add a case
entry in the idle code, as they can use the standard idle loop like the
5K processors.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11099/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For bootloaders that support booting only ELF kernels and load only ELF
segments to memory there is no easy way to supply DTB without kernel
recompilation. For that purpose, create a section called .appended_dtb
that can be later updated with board-specific DTB using binutils e.g. at
kernel installation time.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Similar to how arm allows using selecting between bootloader arguments,
dtb arguments and both, allow to select them on mips. But since we have
less control over the place of the dtb do not modify it but instead use
the boot_command_line for merging them.
The default is "use bootloader arguments" to keep the current behaviour
as default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11284/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add user-mode implementations of gettimeofday() and clock_gettime() to
the VDSO. This is currently usable with 2 clocksources: the CP0 count
register, which is accessible to user-mode via RDHWR on R2 and later
cores, or the MIPS Global Interrupt Controller (GIC) timer, which
provides a "user-mode visible" section containing a mirror of its
counter registers. This section must be mapped into user memory, which
is done below the VDSO data page.
When a supported clocksource is not in use, the VDSO functions will
return -ENOSYS, which causes libc to fall back on the standard syscall
path.
When support for neither of these clocksources is compiled into the
kernel at all, the VDSO still provides clock_gettime(), as the coarse
realtime/monotonic clocks can still be implemented. However,
gettimeofday() is not provided in this case as nothing can be done
without a suitable clocksource. This causes the symbol lookup to fail
in libc and it will then always use the standard syscall path.
This patch includes a workaround for a bug in QEMU which results in
RDHWR on the CP0 count register always returning a constant (incorrect)
value. A fix for this has been submitted, and the workaround can be
removed after the fix has been in stable releases for a reasonable
amount of time.
A simple performance test which calls gettimeofday() 1000 times in a
loop and calculates the average execution time gives the following
results on a Malta + I6400 (running at 20MHz):
- Syscall: ~31000 ns
- VDSO (GIC): ~15000 ns
- VDSO (CP0): ~9500 ns
[markos.chandras@imgtec.com:
- Minor code re-arrangements in order for mappings to be made
in the order they appear to the process' address space.
- Move do_{monotonic, realtime} outside of the MIPS_CLOCK_VSYSCALL ifdef
- Use gic_get_usm_range so we can do the GIC mapping in the
arch/mips/kernel/vdso instead of the GIC irqchip driver]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add an initial implementation of a proper (i.e. an ELF shared library)
VDSO. With this commit it does not export any symbols, it only replaces
the current signal return trampoline page. A later commit will add user
implementations of gettimeofday()/clock_gettime().
To support both new toolchains and old ones which don't generate ABI
flags section, we define its content manually and then use a tool
(genvdso) to patch up the section to have the correct name and type.
genvdso also extracts symbol offsets ({,rt_}sigreturn) needed by the
kernel, and generates a C file containing a "struct mips_vdso_image"
containing both the VDSO data and these offsets. This C file is
compiled into the kernel.
On 64-bit kernels we require a different VDSO for each supported ABI,
so we may build up to 3 different VDSOs. The VDSO to use is selected by
the mips_abi structure.
A kernel/user shared data page is created and mapped below the VDSO
image. This is currently empty, but will be used by the user time
function implementations which are added later.
[markos.chandras@imgtec.com:
- Add more comments
- Move abi detection in genvdso.h since it's the get_symbol function
that needs it.
- Add an R6 specific way to calculate the base address of VDSO in order
to avoid the branch instruction which affects performance.
- Do not patch .gnu.attributes since it's not needed for dynamic linking.
- Simplify Makefile a little bit.
- checkpatch fixes
- Restrict VDSO support for binutils < 2.25 for pre-R6
- Include atomic64.h for O32 variant on MIPS64]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Extend the existing support for Hardware Table Walking (HTW) to MIPS64
systems by supporting PMDs & setting the pointer size bit in PWSize,
then ceasing to blacklist HTW on MIPS64 systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11224/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prior to release 6 of the MIPS architecture it has been implementation
dependent whether masked interrupts cause a wait instruction to return,
so the kernel has effectively had to maintain a whitelist of cores upon
which it is safe to use the r4k_wait_irqoff cpu_wait implementation.
With MIPSr6 this is no longer implementation dependent and
r4k_wait_irqoff can always be used.
Remove the existing I6400 case which will no longer ever be hit, and was
incorrect anyway since I6400 & r6 in general doesn't have the WII bit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ensure the update to which core the core-other GCR regions reflect has
taken place before any core-other GCRs are accessed by placing a memory
barrier (sync instruction) between the write to the core-other registers
and any such GCR accesses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11209/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Document that CPC core-other accesses must take place within the bounds
of the CM lock, and begin using the CM lock functions where we access
the GCRs of other cores. This is required because with CM3 the CPC began
using GCR_CL_OTHER instead of CPC_CL_OTHER.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11208/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce mips_cm_lock_other & mips_cm_unlock_other, mirroring the
existing CPC equivalents, in order to lock access from the current core
to another via the core-other GCR region. This hasn't been required in
the past but with CM3 the CPC starts using GCR_CL_OTHER rather than
CPC_CL_OTHER and this will be required for safety.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11207/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging core bringup it is useful to see the state of the CPC
sequencer, so output that value if the core hasn't started within a
reasonable amount of time (1 second). This avoids simply appearing to
the user to hang if a secondary core fails to start.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Config1 register is architecturally defined as required, and is thus
present in all systems which may make use of cps-vec.S. Skip the check
for its presence via the Config.M bit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11204/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than patching the start of mips_cps_core_entry to provide the
base address of the CM GCRs, simply read that base address from the cop0
CMGCRBase register, converting from the physical address to an uncached
virtual address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide support for outputting early debug information, in the form of
various register values should an exception occur, during the early
bringup of secondary cores. This code requires an ns16550-compatible
UART accessible from the secondary core, and is written in assembly due
to the environment in which such early exceptions occur where way may
not have a stack, be coherent or even have initialised caches.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11202/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
OCTEON Pre-SDK-1.8.1 bootloaders can not handle PT_NOTE program headers,
so do not emit them.
Before the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 2 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
After the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 1 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
The patch was tested on DSR-1000N router.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11403/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Discard .MIPS.abiflags from vmlinux. It's not needed and will cause
issues e.g. with old OCTEON bootloaders that cannot tolerate
additional program headers.
Before the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 3 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
ABIFLAGS 0x00000000005e77f0 0xffffffff816e67f0 0xffffffff816e67f0
0x0000000000000018 0x0000000000000018 R 8
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
After the patch:
$ readelf --program-headers octeon-vmlinux
Elf file type is EXEC (Executable file)
Entry point 0xffffffff815d09d0
There are 2 program headers, starting at offset 64
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000001000 0xffffffff81100000 0xffffffff81100000
0x0000000000b57f80 0x0000000001b86360 RWE 1000
NOTE 0x00000000004e02e0 0xffffffff815df2e0 0xffffffff815df2e0
0x0000000000000024 0x0000000000000024 R 4
Suggested-by: Matthew Fortune <matthew.fortune@imgtec.com>
Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11402/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM7425 CPU Interface Zephyr Processor, pages 5-309 and 5-310
BCM7428B0 CPU Interface Zephyr Processor, pages 5-337 and 5-338
WAIT instruction:
Thread enters wait state. No instructions are executed until an
interrupt occurs. The processor's clocks are stopped if both threads
are in idle mode.
Description:
Execution of this instruction puts the thread into wait state, an idle
mode in which no instructions are fetched or executed. The thread remains
in wait state until an interrupt occurs that is not masked by the
interrupt mask field in the Status register. Then, if interrupts are
enabled by the IE bit in the Status register, the interrupt is serviced.
The ERET instruction returns to the instruction following the WAIT
instruction. If interrupts are disabled, the processor resumes executing
instructions with the next sequential instruction.
Programming notes:
The WAIT instruction should be executed while interrupts are disabled
by the IE bit in the Status register. This avoids a potential timing
hazard, which occurs if an interrupt is taken between testing the counter
and executing the WAIT instruction. In this hazard case, the interrupt
will have been completed before the WAIT instruction is executed, so
the processor will remain indefinitely in wait state until the next
interrupt.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: cernekee@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11322/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the kernel may make use of 64 bit addresses outside of the
compatibility address space then we need to set KX such that those
accesses can succeed. Do so for MIPS64 kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set the Status.BEV bit throughout the early startup of a secondary core
such that if an exception occurs the core branches to one of the
exception vector entries from cps-vec.S, rather than branching to
whatever is set in EBase.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11200/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CM3 has 64 bit GCR_ERROR_* registers, but the code in
mips_cm_error_report was previously only reading 32 bits of it in MIPS32
kernels. Fix by splitting the reads for CM2 & CM3, and making use of the
read64_ variants of the accessor function for CM3.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3885c2b463 ("MIPS: CM: Add support for reporting CM cache
errors") added cases for decoding errors reported by CM3, but leaves the
buf variable which is printed as a string uninitialised for cause values
other than 1, 2 or 3. Fix by ensuring the buf variable is initialised to
an empty string in such cases.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3885c2b463 ("MIPS: CM: Add support for reporting CM cache
errors") leads to Malta boards unconditionally reading CM GCRs upon bus
errors, regardless of whether a CM is present. This is incorrect & will
lead to further exceptions. Fix by moving the GCR reads to after the
check for whether a CM is present.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11186/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than #ifdef on CONFIG_KVM_GUEST & redefine the guest kseg0 base
locally, make use of the CAC_BASE macro which has the correct value in
both cases.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have many extern declarations of mips_debugfs_dir through arch/mips/
in various C files. Unify them by declaring mips_debugfs_dir in a
header, including it in each affected C file & removing the duplicate
declarations.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1a3d59579b ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CONFIG_MIPS_MT symbol can be selected by CONFIG_MIPS_VPE_LOADER in
addition to CONFIG_MIPS_MT_SMP. We only want MT code in the CPS SMP boot
vector if we're using MT for SMP. Thus switch the config symbol we ifdef
against to CONFIG_MIPS_MT_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10867/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MT-specific code in mips_cps_boot_vpes can safely be omitted from
kernels which don't support MT, with the default VPE==0 case being used
as it would be after the has_mt (Config3.MT) check failed at runtime.
Discarding the code entirely will save us a few bytes & allow cleaner
handling of MT ASE instructions by later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The has_mt macro ended with a branch, leaving its callers with a delay
slot that would be executed if Config3.MT is not set. However it would
not be executed if Config3 (or earlier Config registers) don't exist
which makes it somewhat inconsistent at best. Fill the delay slot in the
macro & fix the mips_cps_boot_vpes caller appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MAARs should be initialised on each CPU (or rather, core) in the system
in order to achieve consistent behaviour & performance. Previously they
have only been initialised on the boot CPU which leads to performance
problems if tasks are later scheduled on a secondary CPU, particularly
if those tasks make use of unaligned vector accesses where some CPUs
don't handle any cases in hardware for non-speculative memory regions.
Fix this by recording the MAAR configuration from the boot CPU and
applying it to secondary CPUs as part of their bringup.
Reported-by: Doug Gilmore <doug.gilmore@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R6 removed the Config4.MMUExtDef field, with the low 16 bits only
allowed to contain FTLB fields, and commit e87569cd6c ("MIPS:
cpu-probe: Fix VTLB/FTLB configuration for R6") updated the probing of
this field to assume an FTLB is always present for R6.
However the FTLB may still be absent. The presence of those fields is
actually specified by the MMU type in the Config.MT field, so use that
(the new cpu_has_ftlb) to determine whether the FTLB is actually
present.
Fixes: e87569cd6c ("MIPS: cpu-probe: Fix VTLB/FTLB configuration for R6")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add cpu_has_ftlb, which specifies that an FTLB is present in addition to
the VTLB, probed based on whether Config.MT == 4 (rather than 1 for
standard JTLB).
This is necessary since MIPS release 6 removes Config4.MMUExtDef, so the
presence of the FTLB fields in Config4 must be determined from Config.MT
instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit a6335fa1 fixed the case with gap between initrd and next usable PFN zone,
but broken the case when initrd is combined with usable memory into one region
(in add_memory_region()). Restore the fixup initially brought in by f9a7febd.
---- error message ----
Unpacking initramfs...
Initramfs unpacking failed: junk in compressed archive
BUG: Bad page state in process swapper pfn:00261
page:81004c20 count:0 mapcount:-127 mapping: (null) index:0x2
flags: 0x0()
page dumped because: nonzero mapcount
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0+ #1782
-----------------------
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reported-by: Tony Wu <tung7970@gmail.com>
Tested-by: Tony Wu <tung7970@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Joe Perches <joe@perches.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Pull locking and atomic updates from Ingo Molnar:
"Main changes in this cycle are:
- Extend atomic primitives with coherent logic op primitives
(atomic_{or,and,xor}()) and deprecate the old partial APIs
(atomic_{set,clear}_mask())
The old ops were incoherent with incompatible signatures across
architectures and with incomplete support. Now every architecture
supports the primitives consistently (by Peter Zijlstra)
- Generic support for 'relaxed atomics':
- _acquire/release/relaxed() flavours of xchg(), cmpxchg() and {add,sub}_return()
- atomic_read_acquire()
- atomic_set_release()
This came out of porting qwrlock code to arm64 (by Will Deacon)
- Clean up the fragile static_key APIs that were causing repeat bugs,
by introducing a new one:
DEFINE_STATIC_KEY_TRUE(name);
DEFINE_STATIC_KEY_FALSE(name);
which define a key of different types with an initial true/false
value.
Then allow:
static_branch_likely()
static_branch_unlikely()
to take a key of either type and emit the right instruction for the
case. To be able to know the 'type' of the static key we encode it
in the jump entry (by Peter Zijlstra)
- Static key self-tests (by Jason Baron)
- qrwlock optimizations (by Waiman Long)
- small futex enhancements (by Davidlohr Bueso)
- ... and misc other changes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
jump_label/x86: Work around asm build bug on older/backported GCCs
locking, ARM, atomics: Define our SMP atomics in terms of _relaxed() operations
locking, include/llist: Use linux/atomic.h instead of asm/cmpxchg.h
locking/qrwlock: Make use of _{acquire|release|relaxed}() atomics
locking/qrwlock: Implement queue_write_unlock() using smp_store_release()
locking/lockref: Remove homebrew cmpxchg64_relaxed() macro definition
locking, asm-generic: Add _{relaxed|acquire|release}() variants for 'atomic_long_t'
locking, asm-generic: Rework atomic-long.h to avoid bulk code duplication
locking/atomics: Add _{acquire|release|relaxed}() variants of some atomic operations
locking, compiler.h: Cast away attributes in the WRITE_ONCE() magic
locking/static_keys: Make verify_keys() static
jump label, locking/static_keys: Update docs
locking/static_keys: Provide a selftest
jump_label: Provide a self-test
s390/uaccess, locking/static_keys: employ static_branch_likely()
x86, tsc, locking/static_keys: Employ static_branch_likely()
locking/static_keys: Add selftest
locking/static_keys: Add a new static_key interface
locking/static_keys: Rework update logic
locking/static_keys: Add static_key_{en,dis}able() helpers
...
Rather than saving the scalar FP or vector context in the assembly
resume function, reuse the existing C code we have in fpu.h to do
exactly that. This reduces duplication, results in a much easier to read
resume function & should allow the compiler to optimise out more MSA
code due to is_msa_enabled()/cpu_has_msa being known-zero at compile
time for kernels without MSA support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If MSA is supported by both the hardware & the kernel then advertise
that support to userland via the AT_HWCAP aux vector.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10799/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When running on a CPU implementing the release 6 of the MIPS32 or MIPS64
ISA, advertise that to userland via the appropriate HWCAP bit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10798/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order for userland to determine whether various features are safe to
use, it will need to know both that the hardware supports those features
and that the kernel is recent enough & configured appropriately to
support them. For example under the O32 modeless FP proposal the dynamic
linker & ifunc resolvers will need this information. The kernel is the
only thing in a position to know availability accurately, so the kernel
needs to provide the information to userland. This patch introduces the
infrastructure to provide the AT_HWCAP aux vector to userland in order
to provide that information. It also defines the 2 currently specified
flags, which indicate MIPSr6 & MSA support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-kernel@vger.kernel.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/10797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is desirable for signal handlers to be allowed to make use of MSA,
particularly if auto vectorisation is used when compiling a program.
The MSA context must therefore be saved & restored before & after
invoking the signal handler. Make use of the extended context structs
defined in the preceding patch to save MSA context after the sigframe
when appropriate.
[ralf@linux-mips.org: Fixed conflicts.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The context introduced by MSA needs to be saved around signals. However,
we can't increase the size of struct sigcontext because that will change
the offset of the signal mask in struct sigframe or struct ucontext.
This patch instead places the new context immediately after the struct
sigframe for traditional signals, or similarly after struct ucontext for
RT signals. The layout of struct sigframe & struct ucontext is identical
from their sigcontext fields onwards, so the offset from the sigcontext
to the extended context will always be the same regardless of the type
of signal.
Userland will be able to search through the extended context by using
the magic values to detect which types of context are present. Any
unrecognised context can be skipped over using the size field of struct
extcontext. Once the magic value END_EXTCONTEXT_MAGIC is seen it is
known that there are no further extended context structures to examine.
This approach is somewhat similar to that taken by ARM to save VFP &
other context at the end of struct ucontext.
Userland can determine whether extended context is present by checking
for the USED_EXTCONTEXT bit in the sc_used_math field of struct
sigcontext. Whilst this could potentially change the historic semantics
of sc_used_math if further extended context which does not imply FP
context were to be introduced in the future, I have been unable to find
any userland code making use of sc_used_math at all. Using one of the
fields described as unused in struct sigcontext was considered, but the
kernel does not already write to those fields so there would be no
guarantee of the field being clear on older kernels. Other alternatives
would be to have userland check the kernel version, or to have a HWCAP
bit indicating presence of extended context. However there is a desire
to have the context & information required to decode it be self
contained such that, for example, debuggers could decode the saved
context easily.
[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sc_used_math field of struct sigcontext & its variants has
traditionally been used as a boolean value indicating only whether or
not floating point context is saved within the sigcontext. With various
supported FP modes & the ability to switch between them this information
will no longer be enough to decode the meaning of the data stored in the
sc_fpregs fields of struct sigcontext.
To make that possible 3 bits are defined within sc_used_math:
- Bit 0 (USED_FP) represents whether FP was used, essentially
providing the boolean flag which sc_used_math as a whole provided
previously.
- Bit 1 (USED_FR1) provides the value of the Status.FR bit at the time
the FP context was saved.
- Bit 2 (USED_HYBRID_FPRS) indicates whether the FP context was saved
under the hybrid FPR scheme. Essentially, when set the odd singles
are located in bits 63:32 of the preceding even indexed sc_fpregs
element.
Any userland that tests whether the sc_used_math field is zero or
non-zero will continue to function as expected. Having said that, I
could not find any userland which uses the sc_used_math field at all.
[ralf@linux-mips.org: Fixed rejects.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These functions are never called & thus dead code. Remove them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/10793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the common FP sigcontext code for O32 binaries running on
MIPS64 kernels now that it is taking appropriate offsets into struct
sigcontext(32) from struct mips_abi.
[ralf@linux-mips.org: Fixed reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a task uses 32 bit floating point, the odd indexed 32b register
values are stored in bits 63:32 of the preceding even indexed 64b
FP register field in saved context. Thus there is no point in
preserving the odd indexed 64b register fields since they hold no
valid context. This patch will cause them to be skipped, as is
already done in arch/mips/kernel/signal32.c.
[ralf@linux-mips.org: Fixed reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/10791/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for sharing protected_{save,restore}_fp_context with
compat ABIs, move the FP usage checks into said functions. This will
both enable that code to be shared, and allow for extensions of it in
further patches to also be shared.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When saving FP state to struct sigcontext, make use of the offsets
provided by struct mips_abi to obtain appropriate addresses for the
sc_fpregs & sc_fpc_csr fields of the sigcontext. This is done only for
the native struct sigcontext in this patch (ie. for O32 in CONFIG_32BIT
kernels or for N64 in CONFIG_64BIT kernels) but is done in preparation
for sharing this code with compat ABIs in further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10789/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add fields to struct mips_abi, which holds information regarding the
kernel-userland ABI regarding signals, to specify the offsets to the FP
related fields within the appropriate variant of struct sigcontext.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10788/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The protected_{save,restore}_fp_context functions had effectively
different implementations for EVA. Simplify & unify the code somewhat
such that EVA configurations simply guarantee the FPU-not-owned path
through the standard code path.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Weinberger <richard@nod.at>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Patchwork: https://patchwork.linux-mips.org/patch/10787/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-txx9 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10607/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-rsb1250 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10606/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-4k driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in the ->set_mode() callback. So, this patch
doesn't provide any set-state callbacks.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10605/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-gt641xx driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10604/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-ds1287 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10603/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate cevt-bcm1480 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Read operation on R_SCD_TIMER_CFG and R_SCD_TIMER_INIT registers isn't
performed now for many modes as there returned values aren't used.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10602/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe Config3 for small page support. This will be useful to give clues
as to whether the PageGrain register exists.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TLB registers are dumped in a couble of places:
- sysrq_tlbdump_single() - when dumping TLB state.
- do_mcheck() - in response to a machine check error.
The main TLB registers also differ between r3k and r4k, but r4k appears
to be assumed.
Refactor this code into a dump_tlb_regs() function, implemented for both
r3k and r4k, and used by both of the above functions.
Fixes: d1e9a4f547 ("MIPS: Add SysRq operation to dump TLBs on all CPUs")
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10721/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MSA architecture specification allows for hardware to not implement
unaligned vector memory accesses in some or all cases. A typical example
of this is the I6400 core which does not implement unaligned vector
memory access when the memory crosses a page boundary. The architecture
also requires that such memory accesses complete successfully as far as
userland is concerned, so the kernel is required to emulate them.
This patch implements support for emulating unaligned MSA ld & st
instructions by copying between the user memory & the tasks FP context
in struct thread_struct, updating hardware registers from there as
appropriate in order to avoid saving & restoring the entire vector
context for each unaligned memory access.
Tested both using an I6400 CPU and with a QEMU build hacked to produce
AdEL exceptions for unaligned vector memory accesses.
[paul.burton@imgtec.com:
- Remove #ifdef's
- Move msa_op into enum major_op rather than #define
- Replace msa_{to,from}_wd with {read,write}_msa_wr_{b,h,w,l} and the
format-agnostic wrappers, removing the custom endian mangling for
big endian systems.
- Restructure the msa_op case in emulate_load_store_insn to share
more code between the load & store cases.
- Avoid the need for a temporary union fpureg on the stack by simply
reusing the already suitably aligned context in struct
thread_struct.
- Use sizeof(*fpr) rather than hardcoding 16 as the size for user
memory checks & copies.
- Stop recalculating the address of the unaligned vector memory access
and rely upon the value read from BadVAddr as we do for other
unaligned memory access instructions.
- Drop the now unused val8 & val16 fields in union fpureg.
- Rewrite commit message.
- General formatting cleanups.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Jie Chen <chenj@lemote.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10573/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce accessor functions allowing the kernel to access arbitrary
vector registers using an arbitrary data format. The accessors are
implemented in assembly, using macros to avoid massive duplication, in
order to make use of the existing support for MSA with & without
toolchain support. The accessors will be used in a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10572/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711e ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
get_c0_compare_int() is defined in several files. Each definition is weak,
so I assume Kconfig prevents two or more from being included. The caller
contains default code used when get_c0_compare_int() isn't defined at all.
Add a weak get_c0_compare_int() definition with the default code and remove
the weak annotation from the declaration.
Then the platform implementations will be strong and will override the weak
default. If multiple platforms are ever configured in, we'll get a link
error instead of calling a random platform's implementation.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10686/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Commit b677bc03d7 ("MIPS: cps-vec: Use macros for various arithmetics
and memory operations") replaced various load & store instructions
through cps-vec.S with the PTR_L & PTR_S macros. However it was somewhat
overzealous in doing so for CM GCR accesses, since the bit width of the
CM doesn't necessarily match that of the CPU. The registers accessed
(GCR_CL_COHERENCE & GCR_CL_ID) should be safe to simply always access
using 32b instructions, so do so in order to avoid issues when using a
32b CM with a 64b CPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Weak header file declarations are error-prone because they make every
definition weak, and the linker chooses one based on link order (see
10629d711e ("PCI: Remove __weak annotation from pcibios_get_phb_of_node
decl")).
That's not a problem for vpe_run() because Kconfig ensures there's never
more than one definition:
- vpe_run() is defined in arch/mips/kernel/vpe-mt.c if
CONFIG_MIPS_VPE_LOADER_MT=y
- vpe_run() is defined in arch/mips/mti-malta/malta-amon.c if
CONFIG_MIPS_CMP=y
- CONFIG_MIPS_VPE_LOADER_MT cannot be set if CONFIG_MIPS_CMP=y
But it's simpler to verify correctness if we remove "weak" from the picture
and test the config symbols directly.
Remove "weak" from the vpe_run() declaration and use #if to test whether a
definition should be present.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
vpe_run() is a weak symbol. If there's no definition of it, its value is
zero.
If vpe_run is zero, return failure early. We're going to fail anyway, so
there's no point in getting a VPE and attempting to load it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's only one implementation of mips_cpc_phys_base(), and it's only used
within the same file, so it doesn't need to be weak, and it doesn't need an
extern declaration.
Remove the extern mips_cpc_phys_base() declaration and make it static.
[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10681/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R6 has dropped the MMUExtDef field from the config4 register and it
now returns 0. However, the return value means nothing in that case
and the only supported configuration for R6 is the VTLB+FTLB
(MMUextDef == 3). As a result, rework the code so that the correct
value is set for R6 cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10651/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a default case for the FTLB enable/disable code. This will be used
to detect that something went wrong in the set_ftlb_enable() function
either because that function knows nothing about the running core, or
simply because the core can't turn its FTLB on/off.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10650/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are so early in the boot process where we really don't want to
stall and wait for CP0 FTLB related changes become visible so just drop
the cp0 hazard barrier.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10649/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CM cache error reporting code is not Malta specific and as such it
should live in the mips-cm.c file. Moreover, CM2 and CM3 differ in the
way cache errors are being recorded to the registers so extend the
previous code to add support for the CM3 as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GCR CPC base register is 64-bit on 64-bit processors so use the
appropriate field.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10645/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CMGCRBase register (CP0, 15, 3) register is 64-bit on MIPS64
so we change its type to unsigned long.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10644/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, the CM accessors were only accessing CM registers as u32
types instead of using the native CM register with. However, newer CMs
may actually be 64-bit on MIPS64 cores. Fortunately, current 64-bit CMs
(CM3) hold all the useful configuration bits in the lower half of the
64-bit registers (at least most of them) so they can still be accessed
using the current 32-bit accessors.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow platforms to perform platform-specific steps before configuring
the L2 cache. This is necessary for platforms with CM3 since the L2
parameters no longer live in the Config2 register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10642/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a case in cpu_probe_mips for the MIPS I6400 processor ID, which sets
the CPU type to the new CPU_I6400.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a CPU_I6400 case to various switch statements, doing the same thing
as for CPU_P5600.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10635/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matthew Fortune <Matthew.Fortune@imgtec.com> reports:
The genex.S file appears to mix the case of a macro between its definition and
use. A cut down example of this is below. The macro __build_clear_none has
lower case 'build' but ends up being instantiated with upper case BUILD. Can
this be fixed on master. It has been picked up by the LLVM integrated assembler
which is currently case sensitive. We are likely to fix the assembler as well
but the code is currently inconsistent in the kernel.
.macro __build_clear_none
.endm
.macro __BUILD_HANDLER exception handler clear verbose ext
.align 5
.globl handle_\exception; .align 2; .type handle_\exception, @function; .ent
handle_\exception, 0; handle_\exception: .frame $29, 184, $29
.set noat
.globl handle_\exception\ext; .type handle_\exception\ext, @function;
handle_\exception\ext:
__BUILD_clear_\clear
.endm
.macro BUILD_HANDLER exception handler clear verbose
__BUILD_HANDLER \exception \handler \clear \verbose _int
.endm
BUILD_HANDLER ftlb ftlb none silent
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Matthew Fortune <Matthew.Fortune@imgtec.com>
Commit 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.
Fixes: 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2. No area does particularly stand
out but we have a two unpleasant ones:
- Kernel ptes are marked with a global bit which allows the kernel to
share kernel TLB entries between all processes. For this to work
both entries of an adjacent even/odd pte pair need to have the
global bit set. There has been a subtle race in setting the other
entry's global bit since ~ 2000 but it take particularly
pathological workloads that essentially do mostly vmalloc/vfree to
trigger this.
This pull request fixes the 64-bit case but leaves the case of 32
bit CPUs with 64 bit ptes unsolved for now. The unfixed cases
affect hardware that is not available in the field yet.
- Instruction emulation requires loading instructions from user space
but the current fast but simplistic approach will fail on pages
that are PROT_EXEC but !PROT_READ. For this reason we temporarily
do not permit this permission and will map pages with PROT_EXEC |
PROT_READ.
The remainder of this pull request is more or less across the field
and the short log explains them well"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make set_pte() SMP safe.
MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
MIPS: Flush RPS on kernel entry with EVA
Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
MIPS: BMIPS: Delete unused Kconfig symbol
MIPS: Export get_c0_perfcount_int()
MIPS: show_stack: Fix stack trace with EVA
MIPS: do_mcheck: Fix kernel code dump with EVA
MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
MIPS: Partially disable RIXI support.
MIPS: Handle page faults of executable but unreadable pages correctly.
MIPS: Malta: Don't reinitialise RTC
MIPS: unaligned: Fix build error on big endian R6 kernels
MIPS: Fix sched_getaffinity with MT FPAFF enabled
MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
CPUFREQ: Loongson2: Fix broken build due to incorrect include.
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This function can leak kernel stack data when the user siginfo_t has a
positive si_code value. The top 16 bits of si_code descibe which fields
in the siginfo_t union are active, but they are treated inconsistently
between copy_siginfo_from_user32, copy_siginfo_to_user32 and
copy_siginfo_to_user.
copy_siginfo_from_user32 is called from rt_sigqueueinfo and
rt_tgsigqueueinfo in which the user has full control overthe top 16 bits
of si_code.
This fixes the following information leaks:
x86: 8 bytes leaked when sending a signal from a 32-bit process to
itself. This leak grows to 16 bytes if the process uses x32.
(si_code = __SI_CHLD)
x86: 100 bytes leaked when sending a signal from a 32-bit process to
a 64-bit process. (si_code = -1)
sparc: 4 bytes leaked when sending a signal from a 32-bit process to a
64-bit process. (si_code = any)
parsic and s390 have similar bugs, but they are not vulnerable because
rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code
to a different process. These bugs are also fixed for consistency.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we've already stepped away from ENABLE is a JMP and DISABLE is a
NOP with the branch_default bits, and are going to make it even worse,
rename it to make it all clearer.
This way we don't mix multiple levels of logic attributes, but have a
plain 'physical' name for what the current instruction patching status
of a jump label is.
This is a first step in removing the naming confusion that has led to
a stream of avoidable bugs such as:
a833581e37 ("x86, perf: Fix static_key bug in load_mm_cr4()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
[ Beefed up the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The show_stack() function deals exclusively with kernel contexts, but if
it gets called in user context with EVA enabled, show_stacktrace() will
attempt to access the stack using EVA accesses, which will either read
other user mapped data, or more likely cause an exception which will be
handled by __get_user().
This is easily reproduced using SysRq t to show all task states, which
results in the following stack dump output:
Stack : (Bad stack address)
Fix by setting the current user access mode to kernel around the call to
show_stacktrace(). This causes __get_user() to use normal loads to read
the kernel stack.
Now we get the correct output, like this:
Stack : 00000000 80168960 00000000 004a0000 00000000 00000000 8060016c 1f3abd0c
1f172cd8 8056f09c 7ff1e450 8014fc3c 00000001 806dd0b0 0000001d 00000002
1f17c6a0 1f17c804 1f17c6a0 8066f6e0 00000000 0000000a 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 0110e800 1f3abd6c 1f17c6a0
...
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/10778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a machine check exception is raised in kernel mode, user context,
with EVA enabled, then the do_mcheck handler will attempt to read the
code around the EPC using EVA load instructions, i.e. as if the reads
were from user mode. This will either read random user data if the
process has anything mapped at the same address, or it will cause an
exception which is handled by __get_user, resulting in this output:
Code: (Bad address in epc)
Fix by setting the current user access mode to kernel if the saved
register context indicates the exception was taken in kernel mode. This
causes __get_user to use normal loads to read the kernel code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/10777/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The majority of SMP platforms handle their IPIs through do_IRQ()
which calls irq_{enter/exit}(). When a call function IPI is received,
smp_call_function_interrupt() is called which also calls
irq_{enter,exit}(), meaning irq_count is raised twice.
When tick broadcasting is used (which is implemented via a call
function IPI), this incorrectly causes all CPU idle time on the core
receiving broadcast ticks to be accounted as time spent servicing
IRQs, as account_process_tick() will account as such if irq_count is
greater than 1. This results in 100% CPU usage being reported on a
core which receives its ticks via broadcast.
This patch removes the SMP smp_call_function_interrupt() wrapper which
calls irq_{enter,exit}(). Platforms which handle their IPIs through
do_IRQ() now call generic_smp_call_function_interrupt() directly to
avoid incrementing irq_count a second time. Platforms which don't
(loongson, sgi-ip27, sibyte) call generic_smp_call_function_interrupt()
wrapped in irq_{enter,exit}().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit eeb5389503 ("MIPS: unaligned: Prevent EVA instructions on kernel
unaligned accesses") renamed the Load* and Store* defines in unaligned.c
to _Load* and _Store* as part of its fix. One define was missed out which
causes big endian R6 kernels to fail to build.
arch/mips/kernel/unaligned.c:880:35:
error: implicit declaration of function '_StoreDW'
#define StoreDW(addr, value, res) _StoreDW(addr, value, res)
^
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Fixes: eeb5389503 ("MIPS: unaligned: Prevent EVA instructions on kernel unaligned accesses")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
p->thread.user_cpus_allowed is zero-initialized and is only filled on
the first sched_setaffinity call.
To avoid adding overhead in the task initialization codepath, simply OR
the returned mask in sched_getaffinity with p->cpus_allowed.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10740/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 01306aeadd ("MIPS: prepare for user enabling of CONFIG_OF")
changed the guards in asm/prom.h from CONFIG_OF to CONFIG_USE_OF, but
missed the actual function declarations in kernel/prom.c, which have
additional dependencies.
Fixes the following build error:
CC arch/mips/kernel/prom.o
arch/mips/kernel/prom.c: In function '__dt_setup_arch':
arch/mips/kernel/prom.c:54:2: error: implicit declaration of function 'early_init_dt_scan' [-Werror=implicit-function-declaration]
if (!early_init_dt_scan(bph))
^
Fixes: 01306aeadd ("MIPS: prepare for user enabling of CONFIG_OF")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10741/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were using the native syscall and that results in subtle breakage.
This is the same issue as fixed in 077d0e6561
(MIPS: N32: Use compat getsockopt syscall) but that commit did fix it only
for N32.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100291
MT_SMP is not the only SMP option for MT cores. The MT_SMP option
allows more than one VPE per core to appear as a secondary CPU in the
system. Because of how CM works, it propagates the address-based
cache ops to the secondary cores but not the index-based ones.
Because of that, the code does not use IPIs to flush the L1 caches on
secondary cores because the CM would have done that already. However,
the CM functionality is independent of the type of SMP kernel so even in
non-MT kernels, IPIs are not necessary. As a result of which, we change
the conditional to depend on the CM presence. Moreover, since VPEs on
the same core share the same L1 caches, there is no need to send an
IPI on all of them so we calculate a suitable cpumask with only one
VPE per core.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace lw/sw and various arithmetic instructions with macros so the
code can work on 64-bit kernels as well.
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for 64-bit CPS support, we replace KSEG0 with CKSEG0
so 64-bit kernels can be supported.
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10590/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cps-vec code assumes O32 ABI and uses t4-t7 in quite a few places. This
breaks the build on 64-bit. As a result of which, use the pseudo-registers
ta0-ta3 to make the code compatible with 64-bit.
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips32r2 is a subset of mips64r2, so we replace mips32r2 with mips64r2
in preparation for 64-bit CPS support.
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PTR_LA macro will pick the correct "la" or "dla" macro to
load an address to a register. This gets rids of the following
warnings (and others) when building a 64-bit CPS kernel:
arch/mips/kernel/cps-vec.S:63: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:159: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:220: Warning: la used to load 64-bit address
arch/mips/kernel/cps-vec.S:240: Warning: la used to load 64-bit address
[...]
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10587/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1d8f1f5a78 ("MIPS: smp-cps: hotplug support") added hotplug
support in the SMP/CPS implementation but it introduced a few build problems
on 64-bit kernels due to pointer being casted to and from 'int' C types. We
fix this problem by using 'unsigned long' instead which should match the size
of the pointers in 32/64-bit kernels. Finally, we fix the comment since the
CM base address is loaded to v1($3) instead of v0.
Fixes the following build problems:
arch/mips/kernel/smp-cps.c: In function 'wait_for_sibling_halt':
arch/mips/kernel/smp-cps.c:366:17: error: cast from pointer to integer of
different size [-Werror=pointer-to-int-cast]
[...]
arch/mips/kernel/smp-cps.c: In function 'cps_cpu_die':
arch/mips/kernel/smp-cps.c:427:13: error: cast to pointer
from integer of different size [-Werror=int-to-pointer-cast]
cc1: all warnings being treated as errors
Fixes: 1d8f1f5a78 ("MIPS: smp-cps: hotplug support")
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10586/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commits f1b44067c1 ("MIPS: Emulate the
new MIPS R6 B{L,G}T{Z,}{AL,}C instructions") and commit
a8ff66f52d ("MIPS: Emulate the new MIPS
R6 B{L,G}E{Z,}{AL,}C instructions") added support for emulating various
branch compact instructions. However, it missed the case for those which
use the old BLEZL and BGTZL opcodes leading to random crashes when the R6
emulator is disabled. We fix this by ensuring that the 'rt' field is not
zero which is always true for these branch compact instructions.
Fixes: f1b44067c1 ("MIPS: Emulate the new MIPS R6 B{L,G}T{Z,}{AL,}C instructions")
Fixes: a8ff66f52d ("MIPS: Emulate the new MIPS R6 B{L,G}E{Z,}{AL,}C instructions")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10582/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit f9a7febd leads to a fact that mapstart and therefore a page bitmap for
bootmem allocator immediately follows initrd_end. This doesn't always work
well on Octeon, where there are holes in PFN ranges (refer to 5b3b1688 and
4MB-aligned PFN allocation). Depending on the inird location it could happen,
that mapstart would be in an area not allocated by plat_mem_setup() in
arch/mips/cavium-octeon/setup.c, but in the alignment hole between initrd and
the next PFN area. Later on this memory will be unconditionally made available
to buddy allocator at the end of free_all_bootmem_core() (mm/bootmem.c).
All of this results in Linux using the memory not designated for Linux in
Octeon's plat_mem_setup(), which in turn means corruption of the memory used
by another OS/baremetal code on the same SoC.
It doesn't look to me as a problem of Octeon platform code, but rather as an
inability of f9a7febd to deal correctly with the fragmented memory-mappings.
Proposed fix moves the check for initrd address to the same calculation-loop
in bootmem_init() (arch/mips/kernel/setup.c), which also accounts for kernel
code location. This should result in mapstart located starting from the first
PFN area after kernel code AND initrd.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: Joe Perches <joe@perches.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Yusuf Khan <yusuf.khan@nokia.com>
Cc: Michael Kreuzer <michael.kreuzer@nokia.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/10594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 46e12c07b3 (MIPS: O32 / 32-bit:
Always copy 4 stack arguments.) change the O32 syscall handler to always
load four arguments from the userspace stack even for syscalls that
require fewer or no arguments to be copied. This removes a large table
from kernel space and need to maintain it. It appeared that it was ok
the implementation chosen requires 16 bytes of readable stack space
above the user stack pointer.
Turned out a few threading implementations munmap the user stack before
the thread exits resulting in errors due to the unreadable stack.
We now treat any failed load as a if the loaded value was zero and let
the actual syscall deal with the situation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
allocate_irqno, free_irqno and alloc_legacy_irqno are a simple allocator
for interrupt numbers from the days when the numer of interrupts was still
fixed to NR_IRQS. This was necessary for the SGI IP27 architecture which
with its flexible architecture and possibly large number of interrupts
doesn't easily fit into the old pattern. These days there are better
alternatives.
Move the allocation code from the arch generic code to the only platform
using it, the SGI IP27 aka Origin 200/2000, Onyx 2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support probing the i8259 programmable interrupt controller, as found on
the Malta board, and using its interrupts via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/10114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for detecting a vmlinux.bin appended dtb and overriding
the boot arguments to match the UHI interface.
Due to the PERCPU section being empty for !SMP, but still modifying
the current address by aligning it to the page size, do not define
it for !SMP builds to allow __appended_dtb to still point to
the actual end of the data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hartley <James.Hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9739/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation to allow users to enable DeviceTree without arch or
machine selecting it, we need to fix build errors on MIPS. When
CONFIG_OF is enabled, device_tree_init cannot be resolved. This is
trivially fixed by using CONFIG_USE_OF instead of CONFIG_OF for prom.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The R12000 added a new feature to enhance branch prediction called
"global history". Per the Vr10000 Series User Manual (U10278EJ4V0UM),
Coprocessor 0, Diagnostic Register (22):
"""
If bit 26 is set, branch prediction uses all eight bits of the global
history register. If bit 26 is not set, then bits 25:23 specify a count
of the number of bits of global history to be used. Thus if bits 26:23
are all zero, global history is disabled.
The global history contains a record of the taken/not-taken status of
recently executed branches, and when used is XOR'ed with the PC of a
branch being predicted to produce a hashed value for indexing the BPT.
Some programs with small "working set of conditional branches" benefit
significantly from the use of such hashing, some see slight performance
degradation.
"""
This patch enables global history on R12000 CPUs and up by setting bit
26 in the branch prediction diagnostic register (CP0 $22) to '1'. Bits
25:23 are left alone so that all eight bits of the global history
register are available for branch prediction.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 854700115ecf ([MIPS] kgdb: add arch support for the kernel's kgdb core)
added the 'kgdb_early_setup' flag to avoid calling trap_init() and init_IRQ()
the second time, however the code that called these functions earlier, from
kgdb_arch_init(), had been already removed by that time, so the flag never
served any useful purpose. Remove the related code along with ugly #ifdef'ery
at last.
[ralf@linux-mips.org: Folded in Guenter Roeck's fix.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Patchwork: https://patchwork.linux-mips.org/patch/10501/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Patchwork: https://patchwork.linux-mips.org/patch/10533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ingenic have actually varied the vendor/company ID of the XBurst cores
across their range of SoCs, whilst keeping the product ID & revision
constant... Add definitions for vendor IDs known to be used in some of
Ingenic's newer SoCs, and handle them in the same way as the existing
Ingenic vendor ID from the JZ4740.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a MIPS specific SysRq operation to dump the TLB entries on all CPUs,
using the 'x' trigger key.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10072/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 334c86c494 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
Fixes: 334c86c494 ("MIPS: IRQ: Add stackoverflow detection")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Adam Jiang <jiang.adam@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 2.6.37+
Patchwork: http://patchwork.linux-mips.org/patch/10531/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the default FCSR value in mask probing, avoiding an FPE exception
where reset has left any exception enable and their corresponding cause
bits set and the register is then rewritten with these bits active.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
bmips_wr_vec() copies exception vector code from start to dst.
The call to dma_cache_wback() needs to flush (end-start) bytes,
starting at dst, from write-back cache to memory.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10193/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the generic mechanism to declare a bitmap instead of unsigned long.
This could fix an overwrite defect of whatever follows irq_map.
Not all "#define NR_IRQS <value>" are a multiple of BITS_PER_LONG so
using DECLARE_BITMAP allocates the proper number of longs required
for the possible bits.
For instance:
arch/mips/include/asm/mach-ath79/irq.h:#define NR_IRQS 51
arch/mips/include/asm/mach-db1x00/irq.h:#define NR_IRQS 152
arch/mips/include/asm/mach-lantiq/falcon/irq.h:#define NR_IRQS 328
Signed-off-by: Joe Perches <joe@perches.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cpu_set was removed (along with a bunch of cpumask helpers) by
commit 2f0f267ea0 ("cpumask: remove deprecated functions.").
Fix this by replacing cpu_set with cpumask_set_cpu. Without this
fix the following error is triggered when CONFIG_MIPS_MT_FPAFF=y.
arch/mips/kernel/smp-cps.c: In function 'cps_smp_setup':
arch/mips/kernel/smp-cps.c:95:3: error: implicit declaration of function 'cpu_set' [-Werror=implicit-function-declaration]
Fixes: 90db024f14 ("MIPS: smp-cps: cpu_set FPU mask if FPU present")
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Acked-by: Niklas Cassel <niklass@axis.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9912/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__show_regs() calls show_regs_print_info(), which already outputs
the Tainted: information. So, no need to output it twice.
Signed-off-by: Petri Gynther <pgynther@google.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9997/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix "BUG: using smp_processor_id() in preemptible" reported in accesses
to thread's FPU defaults: the value to initialise FSCR to at program
startup, the FCSR r/w mask and the contents of FIR in full FPU
emulation, removing a regression introduced with 9b26616c [MIPS: Respect
the ISA level in FCSR handling] and f6843626 [MIPS: math-emu: Set FIR
feature flags for full emulation].
Use `boot_cpu_data' to obtain the data from, following the approach that
`cpu_has_*' macros take and avoiding the call to `smp_processor_id' made
in the reference to `current_cpu_data'. The contents of FSCR have to be
consistent across processors in an SMP system, the settings there must
not change as a thread is migrated across processors. And the contents
of FIR are guaranteed to be consistent in FPU emulation, by definition.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Paul Martin <paul.martin@codethink.co.uk>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 46490b5725 ("MIPS: kernel: elf: Improve the overall ABI and FPU
mode checks") reworked the ELF FP ABI mode selection logic, but when
CONFIG_MIPS_O32_FP64_SUPPORT is enabled it breaks the use of binaries
which have no PT_MIPS_ABIFLAGS program header & associated
.MIPS.abiflags section.
A default mode is selected based upon whether the ELF contains MIPS32 or
MIPS64 code, but that selection is made in arch_elf_pt_proc.
arch_elf_pt_proc only executes when a PT_MIPS_ABIFLAGS program header is
found. If one is not found then arch_elf_pt_proc is never called, and no
default overall_fp_mode value is selected. When arch_check_elf is
called, both abi0 & abi1 are MIPS_ABI_FP_UNKNOWN which leads to both
prog_req & interp_req being set to none_req. none_req matches none of
the conditions for mode selection at the end of arch_check_elf, so
overall_fp_mode is left untouched. Finally once mips_set_personality_fp
is called the BUG() in the default case is then hit & the kernel likely
panics.
Fix this by moving the selection of a default overall mode to the start
of arch_check_elf, which runs once per ELF executed regardless of
whether it has a PT_MIPS_ABIFLAGS program header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.0+
Patchwork: http://patchwork.linux-mips.org/patch/9978/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/smp.o
arch/mips/kernel/smp.c: In function ‘start_secondary’:
arch/mips/kernel/smp.c:149:2: error: passing argument 2 of ‘cpumask_set_cpu’ discards ‘volatile’ qualifier from pointer target type [-Werror]
cpumask_set_cpu(cpu, &cpu_callin_map);
^
In file included from ./arch/mips/include/asm/processor.h:14:0,
from ./arch/mips/include/asm/thread_info.h:15,
from include/linux/thread_info.h:54,
from include/asm-generic/preempt.h:4,
from arch/mips/include/generated/asm/preempt.h:1,
from include/linux/preempt.h:18,
from include/linux/interrupt.h:8,
from arch/mips/kernel/smp.c:24:
include/linux/cpumask.h:272:91: note: expected ‘struct cpumask *’ but argument is of type ‘volatile struct cpumask_t *’
static inline void cpumask_set_cpu(unsigned int cpu, struct cpumask *dstp)
^
arch/mips/kernel/smp.c: In function ‘smp_prepare_boot_cpu’:
arch/mips/kernel/smp.c:211:2: error: passing argument 2 of ‘cpumask_set_cpu’ discards ‘volatile’ qualifier from pointer target type [-Werror]
cpumask_set_cpu(0, &cpu_callin_map);
^
In file included from ./arch/mips/include/asm/processor.h:14:0,
from ./arch/mips/include/asm/thread_info.h:15,
from include/linux/thread_info.h:54,
from include/asm-generic/preempt.h:4,
from arch/mips/include/generated/asm/preempt.h:1,
from include/linux/preempt.h:18,
from include/linux/interrupt.h:8,
from arch/mips/kernel/smp.c:24:
include/linux/cpumask.h:272:91: note: expected ‘struct cpumask *’ but argument is of type ‘volatile struct cpumask_t *’
static inline void cpumask_set_cpu(unsigned int cpu, struct cpumask *dstp)
^
arch/mips/kernel/smp.c: In function ‘__cpu_up’:
arch/mips/kernel/smp.c:221:10: error: passing argument 2 of ‘cpumask_test_cpu’ discards ‘volatile’ qualifier from pointer target type [-Werror]
while (!cpumask_test_cpu(cpu, &cpu_callin_map))
^
In file included from ./arch/mips/include/asm/processor.h:14:0,
from ./arch/mips/include/asm/thread_info.h:15,
from include/linux/thread_info.h:54,
from include/asm-generic/preempt.h:4,
from arch/mips/include/generated/asm/preempt.h:1,
from include/linux/preempt.h:18,
from include/linux/interrupt.h:8,
from arch/mips/kernel/smp.c:24:
include/linux/cpumask.h:294:90: note: expected ‘const struct cpumask *’ but argument is of type ‘volatile struct cpumask_t *’
static inline int cpumask_test_cpu(int cpu, const struct cpumask *cpumask)
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/kernel/smp.o] Error 1
make[1]: *** [arch/mips/kernel] Error 2
make: *** [arch/mips] Error 2
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Commit 6ebb496ffc7e("MIPS: kernel: entry.S: Add MIPS R6 related
definitions") added the MIPSR6 definition but it did not update the
ISA level of the actual assembly code so a pre-MIPSR6 jr.hb instruction
was generated instead. Fix this by using the MISP_ISA_LEVEL_RAW macro.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 6ebb496ffc7e("MIPS: kernel: entry.S: Add MIPS R6 related definitions")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When emulating a regular lh/lw/lhu/sh/sw we need to use the appropriate
instruction if we are in EVA mode. This is necessary for userspace
applications which trigger alignment exceptions. In such case, the
userspace load/store instruction needs to be emulated with the correct
eva/non-eva instruction by the kernel emulator.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's best to surround such complex macros with do {} while statements
so they can appear as independent logical blocks when used within other
control blocks.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9502/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c1771216ab ("MIPS: kernel: unaligned: Handle unaligned
accesses for EVA") allowed unaligned accesses to be emulated for
EVA. However, when emulating regular load/store unaligned accesses,
we need to use the appropriate "address space" instructions for that.
Previously, an unaligned load/store instruction in kernel space would
have used the corresponding EVA instructions to emulate it which led to
segmentation faults because of the address translation that happens
with EVA instructions. This is now fixed by using the EVA instruction
only when emulating EVA unaligned accesses.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9501/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Factor out FPU feature probing, mainly to remove code duplication from
`fpu_disable'. No functional change although shuffle some code to avoid
forward references.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9712/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Define the central place the default FCSR value is set from, initialised
in `cpu_probe'. Determine the FCSR mask applied to values written to
the register with CTC1 in the full emulation mode and via ptrace(2),
according to the ISA level of processor hardware or the writability of
bits 31:18 if actual FPU hardware is used.
Software may rely on FCSR bits whose functions our emulator does not
implement, so it should not allow them to be set or software may get
confused. For ptrace(2) it's just sanity.
[ralf@linux-mips.org: Fixed double inclusion of <asm/current.h>.]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9711/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement FIR feature flags in the FPU emulator according to features
supported and architecture level requirements. The W, L and F64 bits
have only been added at level #2 even though the features they refer to
were also included with the MIPS64r1 ISA and the W fixed-point format
also with the MIPS32r1 ISA.
This is only relevant for the full emulation mode and the emulated CFC1
instruction as well as ptrace(2) accesses.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct an ISA level determination problem introduced with 8b8aa636
[MIPS: kernel: cpu-probe.c: Add support for MIPS R6], reverting explicit
masking against individual `MIPS_CPU_ISA_*' macros in FPU feature
determination.
Feature macros such as `cpu_has_mips_r' cannot be used here, because
they operate on CPU #0 and we want to refer to the current CPU instead.
They cannot be used for masking against the current CPU either because
they mask against CPU #0 too, e.g.:
# define cpu_has_mips32r1 (cpu_data[0].isa_level & MIPS_CPU_ISA_M32R1)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rework `process_fpemu_return' and move IEEE 754 exception interpretation
there, from `do_fpe'. Record the cause bits set in FCSR before they are
cleared and pass them through to `process_fpemu_return' so as to set
`si_code' correctly too for SIGFPE signals sent from emulation rather
than those issued by hardware with the FPE processor exception only.
For simplicity `mipsr2_decoder' assumes `*fcr31' has been preinitialised
and only sets it to anything if an FPU instruction has been emulated,
which in turn is the only case SIGFPE can be issued for here.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clear any FCSR cause bits recorded in the saved FPU context after
emulation in all cases rather than in `do_fpe' only, so that any
unmasked IEEE 754 exception left from emulation does not cause a fatal
kernel-mode FPE hardware exception with the CTC1 instruction used by the
kernel to subsequently restore FCSR hardware from the saved FPU context.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Respect the FCSR exception mask when interpreting the IEEE 754 exception
condition to report with SIGFPE in `si_code', so as not to use one that
has been masked where a different one set in parallel caused the FPE
hardware exception to trigger. As per the IEEE Std 754 the Inexact
exception can happen together with Overflow or Underflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct ISA requirements for floating-point instructions:
* the CU3 exception signifies a real COP3 instruction in MIPS I & II,
* the BC1FL and BC1TL instructions are not supported in MIPS I,
* the SQRT.fmt instructions are indeed supported in MIPS II,
* the LDC1 and SDC1 instructions are indeed supported in MIPS32r1,
* the CEIL.W.fmt, FLOOR.W.fmt, ROUND.W.fmt and TRUNC.W.fmt instructions
are indeed supported in MIPS32,
* the CVT.L.fmt and CVT.fmt.L instructions are indeed supported in
MIPS32r2 and MIPS32r6,
* the CEIL.L.fmt, FLOOR.L.fmt, ROUND.L.fmt and TRUNC.L.fmt instructions
are indeed supported in MIPS32r2 and MIPS32r6,
* the RSQRT.fmt and RECIP.fmt instructions are indeed supported in
MIPS64r1,
Also simplify conditionals for MIPS III and MIPS IV FPU instructions and
the handling of the MOVCI minor opcode.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not lose the other half of the BREAK code where there is an upper
half. This is so that e.g. `BREAK 7, 7' is not interpreted as a divide
by zero trap, while `BREAK 0, 7' or `BREAK 7, 0' still are.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9697/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the missing microMIPS BREAK16 instruction code interpretation and
reshape code removing instruction fetching duplication and the separate
call to `do_trap_or_bp' in the MIPS16 path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9696/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the interpretation of the immediate MIPS16 BREAK instruction
code embedded in the instruction word across bits 10:5 rather than 11:6
as current code implies, fixing the interpretation of integer overflow
and divide by zero traps.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9695/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a hardcoded numeric bitmask for FCSR cause bits with
`FPU_CSR_ALL_X' in `__build_clear_fpe'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes applied to `do_cpu' over time reduced the use of the SIGILL
issued with `force_sig' at the end to a single CU3 case only in the
switch statement there. Move that `force_sig' call over to right where
required then and toss out the pile of gotos now not needed to skip over
the call, replacing them with regular breaks out of the switch.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fold a nested `if' statement for the R6 case in `do_ri' into its
containing `if' block, removing excessive indentation causing code to
extend beyond 79 columns.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 46490b57 [MIPS: kernel: elf: Improve the overall ABI and FPU mode
checks] reduced `get_fp_abi' to an elaborate pass-through. Drop it
then.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct a copy-and-paste issue with the description for `movf_func'
referring to `movt_func'. Reformat the former function to match the
latter.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reword the comment for `__cpu_has_fpu' to make it unambiguous this code
is for external floating-point units only, generally MIPS I processors
using the original CP1 hardware interface.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9673/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adjust the explanatory comment for FPU emulator traps according to
ba3049ed [MIPS: Switch FPU emulator trap to BREAK instruction.];
originally coming from `do_ade'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows the kernel to correctly detect an R16000 MIPS CPU on systems that
have those. Otherwise, such systems will detect the CPU as an R14000, due to
similarities in the CPU PRId value.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a machine-specific hook is not implemented for restart, poweroff,
or halt, fall back to halting secondary CPUs, disabling interrupts,
and spinning. In the case of restart, attempt to restart the system
via do_kernel_restart() (which will call any registered restart
handlers) before halting.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since cpu_wait() enables interrupts upon return, CPUs which have
entered stop_this_cpu() may still end up handling interrupts.
This can lead to the softlockup detector firing on a panic or
restart/poweroff/halt. Just disable interrupts and spin to ensure
nothing else runs on the CPU once it has entered stop_this_cpu().
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9601/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove a cast to the 'mips16e_instruction' union inside an if
condition and instead do an assignment to a local
'union mips16e_instruction' variable's 'full' member before the if
statement and use this variable in the if condition.
This is the error message reported by clang:
arch/mips/kernel/branch.c:38:8: error: cast to union type from type 'unsigned short' not present in union
if (((union mips16e_instruction)inst).ri.opcode
^ ~~~~
The changed code can be compiled successfully by both gcc and clang.
Signed-off-by: Toma Tabacu <toma.tabacu@imgtec.com>
Signed-off-by: Daniel Sanders <daniel.sanders@imgtec.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to make checkpatch.pl happy for the next patch. It would otherwise
say --
ERROR: Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already includes
a copy of the GPL.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: macro@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9487/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki