apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.
In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add beacon control by BSS_CHANGED_BEACON_ENABLED and
bss_conf->enable_beacon from mac80211.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to "mac80211: allow configure_filter callback to sleep",
we no longer have to defer the work to the workqueue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
queue == __AR9170_NUM_TXQ would cause a bug on the next line.
found by Smatch ( http://repo.or.cz/w/smatch.git ).
Cc: stable@kernel.org
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ar9170-2.fw was missing, the driver erroneously complained
about missing the initialization values file ar9170-1.fw...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make atheros wireless drivers visible when you select
"Atheros wirless drivers". Adds links to ath.ko page,
and Atheros drivers page on the wiki.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cancel_delayed_work_sync() and cancel_work_sync() are already being
used therefore already waiting for all pending work by the driver
to have been completed, no need to flush the mac80211 workqueue.
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this build error when CONFIG_AR9170_LEDS is not set
drivers/net/wireless/ath/ar9170/main.c:1296: error: 'struct ar9170' has
no member named 'led_work'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch roughly implements xmit aggregation for ar9170-like device.
Not all AP are compatible with the driver(and firmware) yet, so YMMV.
A more refined code will definitely need the final HT specification
to be available for the public, lots of firmware modification and
possibly a redesigned driver just for good measure.
Sadly, these conditions won't come true anytime soon...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky reported that the driver forwarded erroneously the
parent device structure instead of the real thing, which of course
led to some dodgy sysfs links (at least?).
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a back-port from aggregation testing code.
In the past, we didn't limit the amount of active tx urbs.
However, ar9170 only has a limited buffer reserved for
pending data frames.
This wasn't much of a problem with the slower 802.11b/g.
We simply stopped the full queue and moved on to something different
in the mean time. But - as you guessed it - this simple approach
stands in way for a decent aggregation implementation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds new commands that the original firmware will not send
but we can use them to debug firmware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes code (deprecated by "cfg80211: add rfkill support" )
main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)
and a useless device state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"[PATCH 3/4 v2] ar9170: fix LED power state handling" revealed
a bug which can cause a ugly crash.
The delayed worker is canceled before the LED class functions are
unregistered... So, if something manages to update the LEDs
while unregister routine is running the timer could fire _after_ the
module has been unloaded.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains a few more mostly random fixes for the USB front-end.
1. handle irq command response, instead of printing it to the console.
2. remove fixed FIXME.
(real fix: "ar9170usb: reset device on resume". )
3. some more one-liner.
- get rid of a useless "return;"
- add a few branch prediction hints in hot-paths
etc.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of Johannes' deadlock report by moving the
mutex_lock right after cancel_work_sync in ar9170_op_stop.
Besides, the janitor does not need to hold the mutex anymore,
so this extra lines can be removed as well.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a minor visual bug in the led code, which
left the LED in the wrong power state when it was toggled
in a _unexpected_ way (e.g: enabling the LED twice).
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in configure_filter's (sub-)routines.
We never really cleared the flags once we updated the hardware state,
so we wasted our resources by applying already active settings.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces 3 new function which are used to update
the MAC state, whenever needed... e.g: after a band switch.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replace a few constant magics which may affected
the device when operating in a 40MHz channel.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch only contains a few uncritical updates for the
hardware definition header.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a simple copy & paste error that affected beacon
transmission in 802.11a mode.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds:
USB 0x057C:0x8401 AVM FRITZ!WLAN USB Stick N
USB 0x057C:0x8402 AVM FRITZ!WLAN USB Stick N 2.4
These devices require the 1-stage firmware, if not present we
don't continue.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
You can get the stage 1 firmware from here:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/ar9170.fw
md5sum: 34feec4ec0eae3bb92c7c1ea2dfb4530
sha1sum: 6e5250498b815c2940d97242de31e054ae44e079
Its license:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/LICENSE
This is a new firmware, tested with WNDA3100.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this build error when CONFIG_PM is not set:
drivers/net/wireless/ath/ar9170/usb.c: In function 'ar9170_usb_probe':
drivers/net/wireless/ath/ar9170/usb.c:692:
error: 'struct usb_device' has no member named 'reset_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove redundant test: outlen is unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of an outstanding comment in
"[PATCH] ar9170usb: fix hang on resume" commit message.
>However, the device does not accept the firmware on resume.
>and it will exit with:
>
>> firmware part 1 upload failed (-71).
>> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)
And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch ar9170 is capable of receiving aggregated 802.11n frames
and sniffing on most networks without having a "debug message overhead".
(Includes phy initialization requested by
Johannes Berg <johannes@sipsolutions.net> -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for configuring HT40 channels
and receiving HT40 to ar9170. Receiving aggregation
doesn't seem to work right now, so it's not enabled.
Same goes for TX aggregation, but that probably needs
even more work.
With this, I can receive roughly 33 Mbits/sec.
The HT capabilities are a little odd, I tried following
otus here -- in particular having SGI_40 but not SGI_20
is a little weird but afaict that's what otus does.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM is not in good condition we cannot continue so
we currently bail out but only ath5k is bailing out properly.
Both ath9k and ar9170 were proceeding and if a user were to run
into this they'd see an obscure panic. Lets propagate the error
as intended and make sure we inform the user by lifting the
error message from debug to a kernel error.
Stable note: You can find a port of this page here:
http://bombadil.infradead.org/~mcgrof/patches/ath9k/ath9k-fix-eeprom.patch.txt
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joerg Albert