eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.
Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Enable on DCACHE_WORD_ACCESS on ppc64le. It should work on
ppc64 and ppc32 but we need to do some testing first.
A somewhat reasonable testcase used to show the performance
improvement - a repeated stat of a 33 byte filename that
doesn't exist:
#include <sys/types.h>
#include <sys/stat.h>
#include <unistd.h>
#define ITERATIONS 10000000
#define PATH "123456781234567812345678123456781"
int main(void)
{
unsigned long i;
struct stat buf;
for (i = 0; i < ITERATIONS; i++)
stat(PATH, &buf);
return 0;
}
runs 27% faster on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use cmpb which compares each byte in two 64 bit values and
for each matching byte places 0xff in the target and 0x00
otherwise.
A simple hash_name microbenchmark:
http://ozlabs.org/~anton/junkcode/hash_name_bench.c
shows this version to be 10-20% faster than running the x86
version on POWER8, depending on the length.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is a rarely exercised case, so we want to have a test to ensure it
works as required.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement a bi-arch and bi-endian version of load_unaligned_zeropad.
Since the fallback case is so rare, a userspace test harness was used
to test this on ppc64le, ppc64 and ppc32:
http://ozlabs.org/~anton/junkcode/test_load_unaligned_zeropad.c
It uses mprotect to force a SEGV across a page boundary, and a SEGV
handler to lookup the exception tables and run the fixup routine.
It also compares the result against a normal load.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We use cma reserved area for creating guest hash page table.
Don't do the reservation in non-hypervisor mode. This avoids unnecessary
CMA reservation when booting with limited memory configs like
fadump and kdump.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need for 3 functions when a single one will do.
Modify the function declaring macros to call the single function.
Reduces object code size a little:
$ size arch/powerpc/platforms/powernv/pci-ioda.o*
text data bss dec hex filename
22303 1073 6680 30056 7568 arch/powerpc/platforms/powernv/pci-ioda.o.new
22840 1121 6776 30737 7811 arch/powerpc/platforms/powernv/pci-ioda.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return value is unnecessary and unused, so make the functions
void instead of int.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We can unindent the bulk of htab_dt_scan_page_sizes() by returning early
if the property is not found. That is nice in and of itself, but also
has the advantage of making it clear that we always return success once
we have found the ibm,segment-page-sizes property.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.
At the moment they are very widely spaced, so that we can accommodate
the line:
ppc64_caches.dcache_line_size = 0xYY
But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.
The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.
Before:
Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
physicalMemorySize = 0x200000000
ppc64_caches.dcache_line_size = 0xf0
ppc64_caches.icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
After:
Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
phys_mem_size = 0x200000000
dcache_line_size = 0xf0
icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are enabling USB unconditionally which results in following build failure
drivers/built-in.o: In function `tb_drom_read':
(.text+0x1b62b70): undefined reference to `usb_speed_string'
make: *** [vmlinux] Error
Enable USB only if USB_SUPPORT is set to avoid such failures
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the following build failure
drivers/built-in.o: In function `nhi_init':
nhi.c:(.init.text+0x63390): undefined reference to `ehci_init_driver'
by adding a dependency on USB_EHCI_HCD which supplies the ehci_init_driver().
Also we need to depend on USB_OHCI_HCD similarly
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
this patches changes some error handling logics in numa_setup_cpu(),
when cpu node is not found, so:
if the cpu is possible, but not present, -1 is kept in numa_cpu_lookup_table,
so later, if the cpu is added, we could set correct numa information for it.
if the cpu is present, then we set the first online node to
numa_cpu_lookup_table instead of 0 ( in case 0 might not be an online node? )
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().
With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.
For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084b6.
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit 2fabf084b6 ("powerpc: reorder per-cpu NUMA information's
initialization"), during boottime, cpu_numa_callback() is called
earlier(before their online) for each cpu, and verify_cpu_node_mapping()
uses cpu_to_node() to check whether siblings are in the same node.
It skips the checking for siblings that are not online yet. So the only
check done here is for the bootcpu, which is online at that time. But
the per-cpu numa_node cpu_to_node() uses hasn't been set up yet (which
will be set up in smp_prepare_cpus()).
So I saw something like following reported:
[ 0.000000] CPU thread siblings 1/2/3 and 0 don't belong to the same
node!
As we don't actually do the checking during this early stage, so maybe
we could directly call numa_setup_cpu() in do_init_bootmem().
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The size field of the op.type word is now the total number of bytes
to be loaded or stored.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This extends the instruction emulation done by analyse_instr() and
emulate_step() to handle a few more instructions that are found in
the kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This splits out the instruction analysis part of emulate_step() into
a separate analyse_instr() function, which decodes the instruction,
but doesn't execute any load or store instructions. It does execute
integer instructions and branches which can be executed purely by
updating register values in the pt_regs struct. For other instructions,
it returns the instruction type and other details in a new
instruction_op struct. emulate_step() then uses that information
to execute loads, stores, cache operations, mfmsr, mtmsr[d], and
(on 64-bit) sc instructions.
The reason for doing this is so that the KVM code can use it instead
of having its own separate instruction emulation code. Possibly the
alignment interrupt handler could also use this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6a6928c3e "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.
There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.
The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.
We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI. A misdirected device interrupt could also
potentially cause it to wake up. In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.
In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt. This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally. Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.
To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs. Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel. Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap. This new function reads the
interrupt from the XICS. If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.
The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA. Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag. The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled. This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I ran some tests to compare hash_64 using shifts and multiplies.
The results:
POWER6: ~2x slower
POWER7: ~2x faster
POWER8: ~2x faster
Now we have a proper config option, select
CONFIG_ARCH_HAS_FAST_MULTIPLIER on POWER7 and POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows the user to build a kernel targeted at POWER8
(ie gcc -mcpu=power8).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When removing a cpu, this patch makes sure that values
gotten from or passed to firmware are in the correct
endian format.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm,ppc-interrupt-server#s property is in big endian format.
These values need to be converted when used by little endian
architectures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id const, too.
While touching these line also put the __init annotation at the right
position where necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_JUMP_LABEL doesn't ensure HAVE_JUMP_LABEL, if it
is not the case use maintainers's own mutex to guard
the modification of global values.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A recent patch added a function prototype for htab_remove_mapping in
c code. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There were a number of prototypes for functions that no longer
exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify things considerably by moving all the ppc32 specific
symbol exports into its own file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the lib symbol exports closer to their function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_DUMP_READ token exists before initalising the elog
infrastructure.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 91"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_ELOG_READ token exists before initalising the elog
infrastructure.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 74"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check that the OPAL_RTC_READ token exists before we use the OPAL RTC.
Refactors the code a little to merge error paths.
This avoids littering the OPAL console with:
"OPAL: Called with bad token 3".
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there is no way to generically check if an OPAL call exists or not
from the host kernel.
This adds an OPAL call opal_check_token() which tells you if the given token is
present in OPAL or not.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix ppc 32 build failure as reported here:
http://kisskb.ellerman.id.au/kisskb/buildresult/11663513/
The error is as follows:
arch/powerpc/include/asm/floppy.h:142:20: error: 'isa_bridge_pcidev' undeclared
(first use in this function)
This is happening since floppy.o is enabled by BLK_DEV_FD which depends on
ARCH_MAY_HAVE_PC_FDC which is in-turn enabled if PPC_PSERIES=n.
The following commit changes the dependency so that ARCH_MAY_HAVE_PC_FDC is
dependent exclusively on PCI since otherwise it will not compile.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
in commit 29f1aff2c (powerpc: Copy bootable images in the default
install script) we changed to copying all the built boot targets based
on the assumption that it's backwards compatible. It turns out that
debian devived installkernel scripts will barf if not given exactly 4
args.
This change reverts make install to just install the vmlinux (we can
change the dfault in a seperate patch) and introduces a new make
zInstall which works with a more flexible installkernel script.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently we only support initiating Service Processor dump from host.
Hence update sysfs message. Also update couple of other error/info
messages.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CR/Z
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm-next
Patch queue for ppc - 2014-09-24
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to let the guest run while the APIC access page is
not pinned. Because subsequent patches will fill in the function
for x86, place the (still empty) x86 implementation in the x86.c file
instead of adding an inline function in kvm_host.h.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
1. We were calling clear_flush_young_notify in unmap_one, but we are
within an mmu notifier invalidate range scope. The spte exists no more
(due to range_start) and the accessed bit info has already been
propagated (due to kvm_pfn_set_accessed). Simply call
clear_flush_young.
2. We clear_flush_young on a primary MMU PMD, but this may be mapped
as a collection of PTEs by the secondary MMU (e.g. during log-dirty).
This required expanding the interface of the clear_flush_young mmu
notifier, so a lot of code has been trivially touched.
3. In the absence of shadow_accessed_mask (e.g. EPT A bit), we emulate
the access bit by blowing the spte. This requires proper synchronizing
with MMU notifier consumers, like every other removal of spte's does.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Include linux/thread_info.h so we can use is_32_bit_task() cleanly.
Then just simplify syscall_get_arch() since is_32_bit_task() works for
all configuration options.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Paris <eparis@redhat.com>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue is not needed at the bottom of a loop.
The Coccinelle semantic patch implementing this change is:
@@
@@
for (...;...;...) {
...
if (...) {
...
- continue;
}
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kvmppc_get_last_inst function recently received a facelift that allowed
us to pass an enum of the type of instruction we want to read into it rather
than an unreadable boolean.
Unfortunately, not all callers ended up passing the enum. This wasn't really
an issue as "true" and "false" happen to match the two enum values we have,
but it's still hard to read.
Update all callers of kvmppc_get_last_inst() to follow the new calling
convention.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch extends the use of illegal instruction as software
breakpoint instruction across the ppc platform. Patch extends
booke program interrupt code to support software breakpoint.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[agraf: Fix bookehv]
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds kernel side support for software breakpoint.
Design is that, by using an illegal instruction, we trap to hypervisor
via Emulation Assistance interrupt, where we check for the illegal instruction
and accordingly we return to Host or Guest. Patch also adds support for
software breakpoint in PR KVM.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that AltiVec and hardware thread support is in place enable e6500 core.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
ePAPR represents hardware threads as cpu node properties in device tree.
So with existing QEMU, hardware threads are simply exposed as vcpus with
one hardware thread.
The e6500 core shares TLBs between hardware threads. Without tlb write
conditional instruction, the Linux kernel uses per core mechanisms to
protect against duplicate TLB entries.
The guest is unable to detect real siblings threads, so it can't use the
TLB protection mechanism. An alternative solution is to use the hypervisor
to allocate different lpids to guest's vcpus that runs simultaneous on real
siblings threads. On systems with two threads per core this patch halves
the size of the lpid pool that the allocator sees and use two lpids per VM.
Use even numbers to speedup vcpu lpid computation with consecutive lpids
per VM: vm1 will use lpids 2 and 3, vm2 lpids 4 and 5, and so on.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix spelling]
Signed-off-by: Alexander Graf <agraf@suse.de>
Since the guest can read the machine's PVR (Processor Version Register)
directly and see the real value, we should disallow userspace from
setting any value for the guest's PVR other than the real host value.
Therefore this makes kvm_arch_vcpu_set_sregs_hv() check the supplied
PVR value and return an error if it is different from the host value,
which has been put into vcpu->arch.pvr at vcpu creation time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Occasional failures have been seen with split-core mode and migration
where the message "KVM: couldn't grab cpu" appears. This increases
the length of time that we wait from 1ms to 10ms, which seems to
work around the issue.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently decide at compile-time which of the SPE or AltiVec units to
support exclusively. Guard kernel defines with CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC and remove shared defines.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Powerpc timer implementation is a copycat version of s390. Now that they removed
the tasklet with commit ea74c0ea1b follow this
optimization.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch emulates debug registers and debug exception
to support guest using debug resource. This enables running
gdb/kgdb etc in guest.
On BOOKE architecture we cannot share debug resources between QEMU and
guest because:
When QEMU is using debug resources then debug exception must
be always enabled. To achieve this we set MSR_DE and also set
MSRP_DEP so guest cannot change MSR_DE.
When emulating debug resource for guest we want guest
to control MSR_DE (enable/disable debug interrupt on need).
So above mentioned two configuration cannot be supported
at the same time. So the result is that we cannot share
debug resources between QEMU and Guest on BOOKE architecture.
In the current design QEMU gets priority over guest, this means that if
QEMU is using debug resources then guest cannot use them and if guest is
using debug resource then QEMU can overwrite them.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Move ONE_REG AltiVec support to powerpc generic layer.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Make ONE_REG generic for server and embedded architectures by moving
kvm_vcpu_ioctl_get_one_reg() and kvm_vcpu_ioctl_set_one_reg() functions
to powerpc layer.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add AltiVec support in KVM for Book3e. FPU support gracefully reuse host
infrastructure so follow the same approach for AltiVec.
Book3e specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which of the SPE or
AltiVec units to support exclusively by using CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC defines. As Alexander Graf suggested, keep SPE and AltiVec
exception handlers distinct to improve code readability.
Guests have the privilege to enable AltiVec, so we always need to support
AltiVec in KVM and implicitly in host to reflect interrupts and to save/restore
the unit context. KVM will be loaded on cores with AltiVec unit only if
CONFIG_ALTIVEC is defined. Use this define to guard KVM AltiVec logic.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Increase FPU laziness by loading the guest state into the unit before entering
the guest instead of doing it on each vcpu schedule. Without this improvement
an interrupt may claim floating point corrupting guest state.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add 'r' to register name r2 in kvmppc_hv_enter.
Also update comment at the top of kvmppc_hv_enter to indicate that R2/TOC is
non-volatile.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Book3E specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which unit to support
exclusively. As Alexander Graf suggested, this will improve code readability
especially in KVM.
Use distinct defines to identify SPE/AltiVec interrupt numbers, reverting
c58ce397 and 6b310fc5 patches that added common defines.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
SPE exception handlers are now defined for 32-bit e500mc cores even though
SPE unit is not present and CONFIG_SPE is undefined.
Restrict SPE exception handlers to e200/e500 cores adding CONFIG_SPE_POSSIBLE
and consequently guard __stup_ivors and __setup_cpu functions.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Guest visible debug register and hardware visible debug registers are
same, so ther is no need to have arch->shadow_dbg_reg, instead use
arch->dbg_reg.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Dbsr is not visible to userspace and we do not think any need to
expose this to userspace because:
Userspace cannot inject debug interrupt to guest (as this
does not know guest ability to handle debug interrupt), so
userspace will always clear DBSR.
Now if userspace has to always clear DBSR in KVM_EXIT_DEBUG
handling then clearing dbsr in kernel looks simple as this
avoid doing SET_SREGS/set_one_reg() to clear DBSR
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch changes the default behavior of MSRP_DEP, that is
guest is not allowed to change the MSR_DE, to guest can change
MSR_DE. When userspace is debugging guest then it override the
default behavior and set MSRP_DEP. This stops guest to change
MSR_DE when userspace is debugging guest.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds "rfdi" instruction emulation which is required for
guest debug hander on BOOKE-HV
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Debug interrupt can be either "critical level" or "debug level".
There are separate set of save/restore registers used for different level.
Example: DSRR0/DSRR1 are used for "debug level" and CSRR0/CSRR1
are used for critical level debug interrupt.
Using CPU_FTR_DEBUG_LVL_EXC to decide which interrupt level to be used.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit c822e73731.
This commit conflicted with a bitmap allocator change that partially
accomplishes the same thing, but which does so more correctly. Revert
this one until it can be respun on top of the correct change.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit 1c98025c6c "powerpc: Dynamic DMA
zone limits" updated how zones are created in paging_init(), but missed
the NUMA version of paging_init(). This was noticed via a linker
error, since dma_pfn_limit_to_zone() was, like the non-NUMA
paging_init(), limited by #ifndef CONFIG_NEED_MULTIPLE_NODES.
It turns out that the NUMA paging_init() was not actually doing
anything different from the standard paging_init(), other than a couple
debug prints, a couple 32-bit-only ifdef sections, and a call to
mark_nonram_nosave(). It's not clear whether mark_nonram_nosave() is
inherently wrong to do for NUMA, or just not useful on targets that
have NUMA, but for now I'm preserving the existing behavior.
Fixes: 1c98025c6c "powerpc: Dynamic DMA zone limits"
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit a95e8c28b3 "powerpc/defconfig: update RTC support" duplicated
the CONFIG_RTC_DRV_DS1307 symbol in mpc85xx_defconfig and
mpc85xx_smp_defconfig, resulting in this:
arch/powerpc/configs/mpc85xx_smp_defconfig:217:warning: override: reassigning to symbol RTC_DRV_DS1307
Fixes: a95e8c28b3 "powerpc/defconfig: update RTC support"
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tasks get their end of stack set to STACK_END_MAGIC with the
aim to catch stack overruns. Currently this feature does not
apply to init_task. This patch removes this restriction.
Note that a similar patch was posted by Prarit Bhargava
some time ago but was never merged:
http://marc.info/?l=linux-kernel&m=127144305403241&w=2
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: aneesh.kumar@linux.vnet.ibm.com
Cc: dzickus@redhat.com
Cc: bmr@redhat.com
Cc: jcastillo@redhat.com
Cc: jgh@redhat.com
Cc: minchan@kernel.org
Cc: tglx@linutronix.de
Cc: hannes@cmpxchg.org
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Daeseok Youn <daeseok.youn@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1410527779-8133-2-git-send-email-atomlin@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change USB controller version to 2.5 in compatible string for T2080/T2081
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32-bit defconfig version has these enabled
for years so make the 64-bit defconfig have them too.
This patch only adds CONFIG_VIRT_DRIVERS,
CONFIG_FSL_HV_MANAGER and CONFIG_PPC_EPAPR_HV_BYTECHAN
other changes being "make savedefconfig" artifacts.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality only
T1042RDB_PI board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1042RDB_PI board:
-add device tree
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1040/T1042RDB is Freescale Reference Design Board.
The board can support both T1040/T1042 QorIQ Power Architecture™ processor.
T1040/T1042RDB board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- QSGMII
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042 RDB board:
-add device tree
-add entry in Kconfig to build
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch wires up three new syscalls for powerpc. The three
new syscalls are seccomp, getrandom and memfd_create.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
CONFIG_FHANDLE is a requirement for systemd and with the increasing
uptake of systemd within distros it makes sense for 64 bit defconfigs
to include it.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
As opal_message_init() uses machine_early_initcall(powernv, ), and
opal_hmi_handler_init() depends on that early initcall, so it also needs
use machine_* to check the machine_id.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Values acquired from Open Firmware are in 32-bit big endian format
and need to be handled on little endian architectures. This patch
ensures values are in cpu endian when hotplugging memory.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=vBFm
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate. This patch moves the to be interpreted bytecode to
read-only pages.
In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9bca ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").
This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).
Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.
Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables. Brad Spengler proposed the same idea
via Twitter during development of this patch.
Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Branching takes two cycles on MPC8xx. Lets duplicate the two instructions
and avoid the branching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
By XORing the upper part of the instruction code, we get a value that can
directly be verified with the second test and we can remove the first test.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
r10 and r3 are only used inside FixupDAR function. So lets save them inside
that function only.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 2321f33790, dirty handling is not
handled here anymore. So we fix the comment.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 2321f33790, r10 is not used anymore
after FixupDAR. There is therefore no need to set it up with the value of DAR.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
SCRATCH0 and SCRATCH1 are only used in Exceptions prologs where no other
exception can happen. There is therefore no need to preserve them accross
TLB handlers, we can use them there as in other exceptions. One of the
advantages is that they do not suffer CPU6 errata unlike M_TW register.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 469d62be92, SPRG2 is used as a
scratch register just like SPRG0 and SPRG1. So Declare it as such and fix
the comment which is not valid anymore since that commit.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Allocate msis such that each time a new interrupt is requested,
the SRS (MSIR register select) to be used is allocated in a
round-robin fashion.
The end result is that the msi interrupts will be spread across
distinct MSIRs with the main benefit that now users can set
affinity to each msi int through the mpic irq backing up the
MSIR register.
This is achieved with the help of a newly introduced msi bitmap
api that allows specifying the starting point when searching
for a free msi interrupt.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rename the irq controller associated with a MSI
interrupt to fsl-msi-<V>, where <V> is the virq
of the cascade irq backing up this MSI interrupt.
This way, one can set the affinity of a MSI
through the cascade irq associated with said MSI
interrupt.
Given this example /proc/interrupts snippet:
CPU0 CPU1 CPU2 CPU3
16: 0 0 0 0 OpenPIC 16 Edge mpic-error-int
17: 0 4 0 0 fsl-msi-224 0 Edge eth0-rx-0
18: 0 5 0 0 fsl-msi-225 1 Edge eth0-tx-0
19: 0 2 0 0 fsl-msi-226 2 Edge eth0
[...]
224: 0 11 0 0 OpenPIC 224 Edge fsl-msi-cascade
225: 0 0 0 0 OpenPIC 225 Edge fsl-msi-cascade
226: 0 0 0 0 OpenPIC 226 Edge fsl-msi-cascade
[...]
To change the affinity of MSI interrupt 17
(having the irq controller named "fsl-msi-224")
instead of writing /proc/irq/17/smp_affinity, use
the associated MSI cascade irq, in this case,
interrupt 224, e.g.:
echo 6 > /proc/irq/224/smp_affinity
Note that a MSI cascade irq covers several MSI
interrupts, so changing the affinity on the
cascade will impact all of the associated MSI
interrupts.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
As we do for other fsl-mpic related cascaded irqchips
(e.g. error ints, mpic timers), use a normal irq handler
for msi irqs too.
This brings some advantages such as mask/unmask/ack/eoi
and irq state taken care behind the scenes, kstats
updates a.s.o plus access to features provided by mpic,
such as affinity.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Store cascade_data in an array inside the driver
data for later use.
Get rid of the msi_virq array since now we can
encapsulate the virqs in the cascade_data
directly and access them through the array
mentioned earlier.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change USB controller version to 2.5 in compatible string for T4240
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The following commit prevents the MPC8548E on the XPedite5200 PrPMC
module from enumerating its PCI/PCI-X bus:
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
The previous patch prevents any Freescale PCI-X bridge from enumerating
the bus, if it is hardware strapped into Agent mode.
In PCI-X, the Host is responsible for driving the PCI-X initialization
pattern to devices on the bus, so that they know whether to operate in
conventional PCI or PCI-X mode as well as what the bus timing will be.
For a PCI-X PrPMC, the pattern is driven by the mezzanine carrier it is
installed onto. Therefore, PrPMCs are PCI-X Agents, but one per system
may still enumerate the bus.
This patch causes the device node of any PCI/PCI-X bridge strapped into
Agent mode to be checked for the fsl,pci-agent-force-enum property. If
the property is present in the node, the bridge will be allowed to
enumerate the bus.
Cc: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add CONFIG_NLS_CODEPAGE_437, CONFIG_NLS_CODEPAGE_850,
CONFIG_NLS_ISO8859_1 in default configs for 85xx
and 86xx socs. Required for mounting vfat file-systems
on USB devices
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The new MSI block in MPIC 4.3 added the MSIIR1 register,
with a different layout, in order to support 16 MSIR
registers. The msi binding was also updated so that
the "reg" reflects the newly introduced MSIIR1 register.
Virtual machines advertise these msi nodes by using the
compatible "fsl,vmpic-msi-v4.3" so add support for it.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows. By the time
max_direct_dma_addr is set to the precise limit, it will be too late to
alter the zone limits, but we should always have at least 2 GiB mapped
(unless RAM is smaller than that).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
A DMA zone is still needed with swiotlb, for coherent allocations.
This doesn't affect platforms that don't use swiotlb or that don't call
swiotlb_detect_4g().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows, and thus
max_direct_dma_addr is less than 4GiB. Honor that limit in
dma_direct_alloc_coherent().
Note that setting the DMA mask to 31 bits is not an option, since many
PCI drivers would fail if we reject 32-bit DMA in dma_supported(), and
we have no control over the setting of coherent_dma_mask if
dma_supported() returns true.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Platform code can call limit_zone_pfn() to set appropriate limits
for ZONE_DMA and ZONE_DMA32, and dma_direct_alloc_coherent() will
select a suitable zone based on a device's mask and the pfn limits that
platform code has configured.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
fc95ca7284 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the beggining was on_each_cpu(), which required an unused argument to
kvm_arch_ops.hardware_{en,dis}able, but this was soon forgotten.
Remove unnecessary arguments that stem from this.
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using static inline is going to save few bytes and cycles.
For example on powerpc, the difference is 700 B after stripping.
(5 kB before)
This patch also deals with two overlooked empty functions:
kvm_arch_flush_shadow was not removed from arch/mips/kvm/mips.c
2df72e9bc KVM: split kvm_arch_flush_shadow
and kvm_arch_sched_in never made it into arch/ia64/kvm/kvm-ia64.c.
e790d9ef6 KVM: add kvm_arch_sched_in
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Opaque KVM structs are useful for prototypes in asm/kvm_host.h, to avoid
"'struct foo' declared inside parameter list" warnings (and consequent
breakage due to conflicting types).
Move them from individual files to a generic place in linux/kvm_types.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 5828f666c0 due to
build failure after merging with pending powerpc changes.
Link: http://lkml.kernel.org/g/20140827142243.6277eaff@canb.auug.org.au
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
tj: Folded a fix patch.
http://lkml.kernel.org/g/alpine.DEB.2.11.1408172143020.9652@gentwo.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Introduce preempt notifiers for architecture specific code.
Advantage over creating a new notifier in every arch is slightly simpler
code and guaranteed call order with respect to kvm_sched_in.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fc95ca7284 claims that there is no
functional change but this is not true as it calls get_order() (which
takes bytes) where it should have called order_base_2() and the kernel
stops on VM_BUG_ON().
This replaces get_order() with order_base_2() (round-up version of ilog2).
Suggested-by: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT6M7XAAoJEMWQL496c2LNTTgP/2rXyrTTGZpK/qrLKHWKYHvr
XL7tcTkhA0OLU64E37fB+xtDXyBYnLsharuwUFSd1LlL1Wnc1cZN5ORRlMJbmjUR
Wvwl0A8/mkhGl4tzzKgJ4z4rMJXvlZfJRpnVoRB5FOn90LI7k/jsf5rIwF/6S90B
6D6II0r4RG9ku1m7g70cToxcIFCzp0V+eu2tym9GnhsyGKlunPT9iNiTpwfVhPAj
QUvMPKIQXReOv6xDU5q6E07839IMf7SdAvciBTHGnCDD7sGziHvnBIShj/2vTDAF
27sGRKrWUnnuxRUMOoIudiYyeHXIdt1WXp6FsS/ztVI37Ijh9YPShJwWGhQDppnp
4tcoSdefqw9IRUajAVWsB0RUW/tCL4a7tggWofylOA6itDi+HZnw6YafE1G1YzxF
q8OFo9uqLcmFQfHDJpk+sdtXoMZzOgrxlEscsGsQ8kd2Uoe8+chgR9EY1sqPkWVF
Zw0FJCTB6spBlsnXeboBGrnvpbPkacwhvesIFO0IANy4j4R55xlEeTcs1fe3ubUf
UhNyyFdnCAUA7e5CAabcAQYsdbEKG6v0Il3H6xts36c8lXCSFXVgNcw5mdCpFCcQ
DZ3/1FGSVzkYNXX8hlzIn1W0dqvwn4x0ZbnpXUJrGUBpSmjt9qkXx0XbdeFwartU
7X4tNGS1jfNYhOdP87jF
=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
Many of the atomic op implementations are the same except for one
instruction; fold the lot into a few CPP macros and reduce LoC.
Requires asm_op because PPC asm is weird :-)
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20140508135852.713980957@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add tracepoint to track hugepage invalidate. This help us
in debugging difficult to track bugs.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On ppc64 we support 4K hash pte with 64K page size. That requires
us to track the hash pte slot information on a per 4k basis. We do that
by storing the slot details in the second half of pte page. The pte bit
_PAGE_COMBO is used to indicate whether the second half need to be
looked while building real_pte. We need to use read memory barrier while
doing that so that load of hidx is not reordered w.r.t _PAGE_COMBO
check. On the store side we already do a lwsync in __hash_page_4K
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We would get wrong results in compiler recomputed old_pmd. Avoid
that by using ACCESS_ONCE
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As per ISA, for 4k base page size we compare 14..65 bits of VA specified
with the entry_VA in tlb. That implies we need to make sure we do a
tlbie with all the possible 4k va we used to access the 16MB hugepage.
With 64k base page size we compare 14..57 bits of VA. Hence we cannot
ignore the lower 24 bits of va while tlbie .We also cannot tlb
invalidate a 16MB entry with just one tlbie instruction because
we don't track which va was used to instantiate the tlb entry.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault for
these pages.
We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.
Use _PAGE_COMBO to determine the page size with which we should
invalidate the hash table entries on unmap.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault
for these pages.
We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.
Handle this correctly for 16M pages
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The segment identifier and segment size will remain the same in
the loop, So we can compute it outside. We also change the
hugepage_invalidate interface so that we can use it the later patch
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With hugepages, we store the hpte valid information in the pte page
whose address is stored in the second half of the PMD. Use a
write barrier to make sure clearing pmd busy bit and updating
hpte valid info are ordered properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.
NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().
Commit 6ee0578b4d ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.
Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:
bce903809a ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad469 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")
Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).
Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.
While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node 0 1
0: 10 40
1: 40 10
the slab consumption decreases from
Slab: 932416 kB
SUnreclaim: 902336 kB
to
Slab: 395264 kB
SUnreclaim: 359424 kB
And we a corresponding increase in the slab efficiency from
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 337 MB 11.28% 100.00%
task_struct 288 MB 9.93% 100.00%
to
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 37 MB 100.00% 100.00%
task_struct 31 MB 100.00% 100.00%
Powerpc didn't support memoryless nodes until recently (64bb80d87f
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c27226119
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression x,E,c;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A buffer returned by H_VTERM_PARTNER_INFO contains device information
in big endian format, causing problems for little endian architectures.
This patch ensures that they are in cpu endian.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xmon only soft disables interrupts. This seems like a bad idea - we
certainly don't want decrementer and PMU exceptions going off when
we are debugging something inside xmon.
This issue was uncovered when the hard lockup detector went off
inside xmon. To ensure we wont get a spurious hard lockup warning,
I also call touch_nmi_watchdog() when exiting xmon.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It appears that commits 7f06f21d40 ("powerpc/tm: Add checking to
treclaim/trechkpt") and e4e3812150 ("KVM: PPC: Book3S HV: Add
transactional memory support") both added definitions of TEXASR_FS.
Remove one of them. At the same time, fix the alignment of the remaining
definition (should be tab-separated like the rest of the #defines).
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan