Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use vmalloc to allocate memory for the firmware image, and use a smaller
linear buffer for the actual transfer of the firmware to the chipset.
This patch is an adaptation of a similar patch for wl1251 by Kalle Valo.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable multicast filtering. This way by default no multicast frames will
reach the host, and when needed, only required multicast frames can be
passed from the WLAN chipset to the host.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear the probe-request template on the firmware after scan. Unless
cleared, the firmware can independently send probe requests to the AP
and interfere with the mac80211 logic.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the workqueue provided by the mac80211 stack instead of the system
default queue.
Modified to use new ieee_queue_work() as required by changes in the
stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a hack to disable all filters in the join command. This is based on
Kalle Valo's patch for wl1251.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Juuso as one of the module authors, since he's working heavily on this
module as well.
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Corrections to the TX path - use correct number of maximum descriptors
(32 instead of 16) and correct checking and setting of excessive retries
on completion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the usage of join's, including using actual beacon interval and
dtim from AP, and configuring a basic rate set from AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the rate policies to the firmware based on the rates given by
the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds implementation for checking for SPI busy words - i.e.
honoring a delay request from the WLAN chipset upon reading
registers/memory.
To optimized the average SPI ready by 32 bits, also configure the number
of busywords to one to disable the "fixed-busy-word" functionality.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ps-poll template aid bits 14 and 15 were not masked as required by
the standard. Mask them so that aid is sent in correct format.
This patch is a direct port of the respective patch for the wl1251
driver by Kalle Valo.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement delayed entry into ELP. This will promote the following:
- Less redundant sleep/wake cycles (better perf)
- Avoids known firmware issues with going to ELP too fast after an
operation
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the position to which TKIP header space is appended for TX
packets.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add security sequence number handling to the driver TX data path needed
by WPA.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the TX path implementation to allocate sufficient blocks in the
firmware for TX packets.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qual element in ieee80211_rx_status is not used anymore, so we don't need
to set it in the wl1271_rx_status() function. This saves a bit of time in
the RX path.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during
reset or initial calibration, update the PA calibration to account
for that and initialize PA calibration variables for both conditions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for the ar9271 hardware as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwmc3200wifi requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is somewhat non-sensical to allow selecting wireless
drivers without showing wireless core code options, and
since the wext refactoring this has made it possible to
generate configurations that will not build. Avoid this
and make wireless drivers select the wireless options.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came in through the patch titled:
libertas: first stab at cfg80211 support
I only noticed it because it breaks compat-wireless :)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: sujith.manoharan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As kindly pointed out by Andrey Yurovsky, CONFIG_LIBERTAS already
selects FW_LOADER.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_is_cmd_allowed() check is added in __lbs_cmd_async() and
lbs_prepare_and_send_command(). The check is removed from other places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And move it to hw code on mac.c where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has long provided us the association ID. This isn't useful except
for Power-Save polling which now gets enabled. We can now poll for our
pending frames on the AP during power save.
You can review the details of Power-Save on the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/power-savings
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression introduced by patch titled:
"atheros: define shared bssidmask setting"
The register for the BSSID was exchanged for the bssid mask register.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have access to common->curbssid and common->curaid so just
use those. Note that common->curaid is always 0 so this keeps
our current behaviour of always using 0 for now. Once we fix
storing the association ID passed by mac80211 this will
require no changes here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The trick was to add four bytes whenever this was used. There
are two places where this was missed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo on the second bssid mask register.
This was caused by the patch titled:
"ath5k: use common curbssid, bssidmask and macaddr"
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also sorts all "source" lines in the wireless/Kconfig.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the suspend and resume callbacks of ath5k by converting the
driver to struct dev_pm_ops and allowing the PCI PM core to do the
PCI-specific suspend/resume handling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set firmware and hardware version in wiphy so that user space can access
it.
(Modification from original in favor of cfg80211 ethtool support. -- JWL)
Cc: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both 1000 & 6000 series NICs contain on-chip OTP memory that
replaces the off-chip EEPROM memory. The nature of OTP means
there is a limited number of times a particular board can go through the
factory flow and be (re)calibrated. As a consequence there will be some boards
that contain EEPROM memory because OTP blocks were full.
In the signature validation routine, iwlwifi needs to make sure
"select bit" and "EEPROM/OTP signature" agree on the type of
NVM to be used to configure the system.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.
The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple MPDUs can be aggregated, transmitted, and finally acknowledged
together using a single BA frame. Block ACK (BA) contains
bitmap size of 64*16 bits so the maximum frame count is 64.
The default value of aggregation frame count suggested by uCode is 31 to
achieve best performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support different type of 1000 series NICs we release to
customers before the production release, iwlwifi driver need to support
all the NICs has EEPROM version greater than 0x15c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.
How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately
Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.
Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.
One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file was accidentally added in commit ef2f8d4577 ("wl1251: add
wl1251 prefix to all 1251 files"). This happened when I rebased the
patches from a private tree.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add timer based auto deep sleep feature in libertas driver which can be
configured using iwconfig command. This is tested on SD8688, SD8686 cards
with firmware versions 10.38.1.p25, 9.70.4.p0 respectively on 32-bit and 64-bit
platforms. Tests have been done for USB/CS cards to make sure that the patch
won't break USB/CS code. We didn't test the if_spi driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows for hw support to be enabled for ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.
The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commenting unused functions lpphy_restore_dig_flt_state and
lpphy_disable_rx_gain_override, may be we need these functions in future.
This also fixed following compilation warnings :
CC [M] drivers/net/wireless/b43/phy_lp.o
drivers/net/wireless/b43/phy_lp.c:383: warning: ‘lpphy_restore_dig_flt_state’ defined but not used
drivers/net/wireless/b43/phy_lp.c:891: warning: ‘lpphy_disable_rx_gain_override’ defined but not used
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.
This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Get power table offset from the EEPROM instead of using
a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values. Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.
This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9170_op_get_tsf: handle a carry from TSF_L into TSF_H
by reading TSF_H twice.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add heavy clip handling for 2.4GHz only (similar to the vendor driver).
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some coding style issues and moves MAX_RATE_POWER into hw.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.
Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.
The supported LED modes after this are:
IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
traffic
IWL_LED_RF_STATE (new) -
LED OFF: No power/RF disabled, the LED is emitting no light
LED ON: Powered/RF enabled, the LED is emitting light
in a stable non-flashing state.
In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.
However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.
We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.
Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OR-in AMPDU flags rather than assigning them. This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove few of the parameters not used and no longer valid in EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify LED blink index table to include 1Mbps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac.c is now core driver independent.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used just to determine how to program the MAC,
either for 20 MHz operation of 40 MHz so just use conf_is_ht40()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was for supporting 25 MHz spacing for HT40, this is not used
as we use 20 MHz spacing instead for HT40 as per 802.11n. The hardware
is capable of it though so we leave the phymode definition and EEPROM
parsing for it. If some experimenter wants to work on this stuff stuff
you can add an extension enabling bool on ath_common and perhaps some
debugfs knob to enable it. Keep in mind you'll also need to update the
phymode with the AR_PHY_FC_DYN2040_EXT_CH which has been left on the
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses this for now, ath9k_htc is expected to re-use this
as well. We lave ath5k as is, but it certainly can also be
converted later.
The ath9k module parameter and debugfs entry is kept.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of it on hw code in ath9k to avoid
using the ath9k ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also make ath5k and ath9k use it, and share register definitions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only common ath read/write ops go through the common ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can propagate better errors upon failed hw initialization,
and set up the ath_common structure for attach purposes. This
will become important once we start using the ath_common
for read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In an effort to make hw code driver core agnostic read
and write operations are defined on the ath_common structure.
This patch adds that and makes ath9k use it. This allows
drivers like ath9k_htc to define its own read/write ops and
still rely on the same hw code. This also paves the way for
sharing code between ath9k/ath5k/ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We disable ASPM when enabling bluetooth coexistance. Disabling
ASPM is a bus specific operation. In the future other buses may
support bluetooth coexistance, an example is USB. To this end
move the current routine which disables ASPM into pci.c, and declare
it the PCI bt_coex_prep() helper. Additionally, since ASPM is
a PCI-Express primitive ensure we don't ever try to muck with ASPM
registers on non PCI-express devices.
This also cleans up hw.c to not include bus specific headers or
utilities.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that we can access common on hw related code
independent of the driver core.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/ath5k/attach.c
drivers/net/wireless/ath/ath5k/attach.c:288:42: warning: symbol 'ee' shadows an earlier one
drivers/net/wireless/ath/ath5k/attach.c:109:34: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ah_sta_id was really being used as the macaddr.
ath5k still does not use the association ID now passed
up by mac80211, that can be fixed later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are common amongst ath9k and ath5k, so put them into the
common structure and make ath9k to use it. ar9170 can use macaddr,
and curbssid. We'll change ath5k and ar9170 separately.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the already provided helper instead of rewriting the code
required in place.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same code was being implemented on reset for setting the bssidmask,
instead just use the already provided helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Historically some macro helpers have been users for this,
AR5K_LOW_ID() and AR5K_HIGH_ID(), use upstream unaligned
helpers instead. This applid to ath5k and ar9170. ath9k
already uses this.
Worth noting is ath5k uses an ah_sta_id but that is already
the MAC address combined with the associaiton ID, ah_sta_id
is really ETH_ALEN in size.
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Nick Kossifidis <mick@madwifi-project.org>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used by both ath5k and ath9k to set the first bssid mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower_nolock --> ath9k_hw_setpower()
ath9k_hw_setpower() --> ath9k_setpower()
Also change the param for ath9k_setpower() to pass the ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower() is a core driver helper with locking
protection. Locking protection should be left to the driver
core, not the hw code. Hardware code no longer contends for
locking when it needs to wake up the chip or put it to sleep.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the TSF is reset power save state is disabled and
then restored. The helpers to disable power save and restore
it use a lock provided by the driver core. Move the callers
of the helpers outside of the hw code.
We reset the TSF when mac80211 tells us and on the beacon.c
helper ath9k_hw_beaconinit() when it is made explicitly required.
Add a helper on beacon.c which will deal with ps awake/restore
if we need to reset the TSF upon ath9k_hw_beaconinit().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also just pass the ath_hw as the parameter.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are only used by btcoex.c on one routine, so stuff them
into that file.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some necessary cleanups we now move ath9k_hw_btcoex_set_weight()
to where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The second argument is always the hardware bt coex struct, so
remove it, and rename the function on the path with a ath9k_ prefix.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex_scheme is already part of a btcoex struct, its implied
this is btcoex related.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bt_stomp_type defines the bt coex weight, it has a one-to-one
mapping. In the future we may want to just use the weight directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen