Add dummy primary plane implementation. LCDC does not really have
planes, only simple framebuffer that is mandatory. This primary plane
implementation has the necessary checks for implementing simple
framebuffer trough DRM plane abstraction. For setting the actual
framebuffer the implementation relies on a CRTC side function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Make tilcdc_crtc_page_flip() work if crtc is not yet on. The plane
commit sometimes comes before crtc is turned on. The new framebuffer
should be set to scanout also in that case, so that it is there when
crtc is turned on at the end of the commit phase.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Fix tilcdc component master unloading. If a subcomponent module
(tda998x in this case) is unloaded before its master (tilcdc in this
case), it calls drm_put_dev() and it should not be called again by
the master when its module is unloaded. However component_master_del()
must still be called and the check if the drm_put_dev() has been
called must be in component_master_ops unbind() callback, not in
platform_driver remove() callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add drm_crtc_vblank_on() and *_off() calls to start() and stop()
functions, to make sure any vblank waits etc. gets properly cleaned
up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Increase time out for waiting frame done interrupt. 50ms is long
enough for the usual display modes (50 Hz or higher refresh rate), but
it may be a bit tight for some unusual mode.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Move wait queue waiting of LCDC_FRAME_DONE IRQ from tilcdc_crtc_dpms()
into stop() function. This is just a cleanup and enables independent
use of stop() function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reorder the IRQ function so that the write to LCDC_END_OF_INT_IND_REG
is done last. The write to LCDC_END_OF_INT_IND_REG indicates to LCDC
that the interrupt service routine has completed (see section
13.3.6.1.6 in AM335x TRM). This is needed if LCDC's ipgvmodirq module
is configured for pulse interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Move LCDC_SYNC_LOST handling inside if (ver == 2) statement.
LCDC_SYNC_LOST interrupt status bit is only defined for version 2
silicon.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.
Fixes commit 614b3cfeb8 ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Shouldn't be possible since everyone kzallocs this, but better safe
than sorry. Random drive-by-idea really.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rdorigo.vivi@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470673493-14304-1-git-send-email-daniel.vetter@ffwll.ch
To properly implement atomic w/ runtime pm, we move
drm_atomic_helper_commit_modeset_enables() above
drm_atomic_helper_commit_planes() to ensure CRTCs are enabled before
modifying plane registers, and set active_only to true to filter out
plane update notifications when the CRTC is disabled.
According to the document from linux kernel:
Set the active_only parameters to true in order not to receive plane
update notifications related to a disabled CRTC. This avoids the need
to manually ignore plane updates in driver code when the driver and/or
hardware can't or just don't need to deal with updates on disabled
CRTCs, for example when supporting runtime PM.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470279597-60453-8-git-send-email-bibby.hsieh@mediatek.com
The mtk_plane_enable is just called once by mtk_plane_atomic_update.
So, merge mtk_plane_enable into mtk_plane_atomic_update.
While we are here, also clean up the function a bit by using an fb local
variables.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470279597-60453-6-git-send-email-bibby.hsieh@mediatek.com
It is not actually useful to a mtk plane to know its zpos/index, so just
remove this field.
This let's completely remove struct mtk_drm_plane in a follow up patch.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470279597-60453-3-git-send-email-bibby.hsieh@mediatek.com
Replace the use of drm_plane_helper_check_update() with
drm_plane_helper_check_state() since we have a plane state.
I don't see any actual users of drm_simple_kms_helper yet, so
no actual plane clipping bugs to fix.
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-10-git-send-email-ville.syrjala@linux.intel.com
Replace the use of drm_plane_helper_check_update() with
drm_plane_helper_check_state() since we have a plane state.
This also eliminates the double clipping the driver was doing
in both check and commit phases). And it should fix src coordinate
addr adjustement. Previously the driver was expecting negative dst
coordinates after clipping, which is not going happen, so any clipping
induced addr adjustment simply didn't happen. Neither did the driver
respect any user configured src coordinates, so panning and such would
have been totally broken. It should be all good now.
Cc: CK Hu <ck.hu@mediatek.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Tested-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-9-git-send-email-ville.syrjala@linux.intel.com
Replace the use of drm_plane_helper_check_update() with
drm_plane_helper_check_state() since we have a plane state.
Rockchip looks to handling plane clipping rather well already
(unlikje most arm drm drivers) so there are no function changes
here.
Cc: Yao <mark.yao@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-8-git-send-email-ville.syrjala@linux.intel.com
Add a version of drm_plane_helper_check_update() which takes a plane
state instead of having the caller pass in everything.
And to reduce code duplication, let's reimplement
drm_plane_helper_check_update() in terms of the new function, by
having a tempororary plane state on the stack.
v2: Add a note that the functions modifies the state (Chris)
v3: Fix drm_plane_helper_check_update() y coordinates (Daniel Kurtz)
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org> (v2)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470642910-14073-1-git-send-email-ville.syrjala@linux.intel.com
Using atomic_mode_set instead of mode_set allows to access crtc
and connector states in addition to the modes. This allows to
remove the connector list walk.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Some encoders need more information from crtc and connector state or
connector display info than just the mode during mode setting. This
patch adds an atomic encoder mode setting variant that passes the crtc
state (which contains the modes) and the connector state.
atomic_enable/disable variants that additionally pass crtc and connector
state don't seem to be necessary for any current driver. mode_fixup
already has an atomic equivalent in atomic_check.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
imx_drm_handle_vblank() is just a simple wrapper of drm_crtc_handle_vblank()
without doing any thing fancy - drm_crtc_handle_vblank() can be called
directly. So, let's remove the wrapper.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rename the CSI client device in the client_reg[] table to
"imx-ipuv3-csi".
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There can be multiple IC tasks using the IRT, so the IRT needs
a separate use counter. Create a private ipu_irt_enable() to
enable the IRT module when any IC task requires rotation, and
ipu_irt_disable() when a task no longer needs the IRT.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The CSI data format was being programmed incorrectly for the
1x16 media bus formats. The CSI data format for 16-bit must
be bayer/generic (CSI_SENS_CONF_DATA_FMT_BAYER).
Suggested-by: Carsten Resch <Carsten.Resch@de.bosch.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Set the sensor full frame based on whether the passed in mbus_fmt
is 720x480 (NTSC) or 720x576 (PAL).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds of-alias id to ipu_soc and retrieve with ipu_get_num().
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_set_uv_offset(), to set planar U/V offsets.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no one calling imx_drm_crtc_id() and it is just a simple
wrapper of drm_crtc_index() without doing any thing fancy - the
drivers may call drm_crtc_index() directly. So, let's remove the
wrapper.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no one calling imx_drm_crtc_vblank_get/_put() and
they are just two simple wrappers of drm_crtc_vblank_get/_put()
without doing any thing fancy - the drivers may call
drm_crtc_vblank_get/_put() directly. So, let's remove the two
wrappers.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The 'de-active' and 'pixelclk-active' DT properties are evaluated
by of_parse_display_timing() called from of_get_drm_display_mode(),
but later lost in the conversion from videomode.flags to
drm_display_mode.flags.
Enhance of_get_drm_display_mode() to also return the bus flags in a
separate variable, so that they can be passed on to the ipu-di
driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
add a helper function to extract information about pixel clock and DE
polarity from DT for use by of_get_drm_display_mode().
While at it, convert spaces to tabs in indentation in drm_modes.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When reconfiguring a plane position (as in moving the cursor), the
frame buffer for the cursor isn't changing, so don't call the prepare
or cleanup driver functions.
This avoids making cursor position updates block on all pending rendering.
v3: use drm_atomic_helper_framebuffer_changed in both prepare and
cleanup phases instead of keeping state in the plane.
cc: dri-devel@lists.freedesktop.org
cc: David Airlie <airlied@linux.ie>
cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
[danvet: Rebase onto 4.8]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Except for nouveau, only legacy drivers need this really. And nouveau
is already marked up with DRIVER_KMS_LEGACY_CONTEXT as the special
case.
I've tried to be careful to leave everything related to modeset still
using the DRIVER_MODESET flag. Otherwise it's a direct replacement of
!DRIVER_MODESET with DRIVER_LEGACY checks. Also helps readability
since fewer negative checks overall.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470251470-30830-2-git-send-email-daniel.vetter@ffwll.ch
It's super confusing that new drivers need to be marked with
DRIVER_MODESET when really it means DRIVER_MODERN. Much better to
invert the meaning and rename it to something that's suitably
off-putting.
Since there's over 100 places using DRIVER_MODESET we need to roll out
this change without a flag day.
v2: Update docs.
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470251470-30830-1-git-send-email-daniel.vetter@ffwll.ch
At a higher level, all objects are created with definite size i.e. 0 is
illegal. In forthcoming patches, this assumption is dependent upon in
the drm_mm range manager, i.e. trying to create a drm_mm node with size
0 will have undefined behaviour. Add a couple of WARNs upon creating the
drm_mm node to prevent later bugs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470248788-30873-1-git-send-email-chris@chris-wilson.co.uk
The minor referred to by "DRM_MINOR_LEGACY" is called 'dev->primary' and
gets 'cardX' as name assigned. Lets reduce this magnificent number of
names for the same concept by one and rename DRM_MINOR_LEGACY to
DRM_MINOR_PRIMARY (to match the actual struct-member name).
Furthermore, this is in no way a legacy node, so lets not call it that.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160803180432.1341-2-dh.herrmann@gmail.com
In addition to the last-in/first-out stack for accessing drm_mm nodes,
we occasionally and in the future often want to find a drm_mm_node by an
address. To do so efficiently we need to track the nodes in an interval
tree - lookups for a particular address will then be O(lg(N)), where N
is the number of nodes in the range manager as opposed to O(N).
Insertion however gains an extra O(lg(N)) step for all nodes
irrespective of whether the interval tree is in use. For future i915
patches, eliminating the linear walk is a significant improvement.
v2: Use generic interval-tree template for u64 and faster insertion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470236651-678-1-git-send-email-chris@chris-wilson.co.uk
It was really strange to see negative vblank seqs on debug
messages. It is rare to have that big number, but when it
happens it is confusing and misleading.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470243226-2750-1-git-send-email-rodrigo.vivi@intel.com
A few fixes for amdgpu and ttm for 4.8
- fix a ttm regression caused by the new pipelining code
- fixes for mullins on amdgpu
- updated golden settings for amdgpu
* 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
3 intel fixes.
* tag 'drm-intel-next-fixes-2016-08-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915/fbdev: Check for the framebuffer before use
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
The conversion of the rcar-du driver from the I2C slave encoder to the
DRM bridge API left the HDMI encoder's bridge pointer NULL, preventing
the bridge from being handled automatically by the DRM core. Fix it.
Fixes: 1d926114d8 ("drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
~jiffie and a few usecs is 3 orders of magnitude different. A bit
much. This was changed in
commit ca5b721e23
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Dec 11 11:32:58 2015 +0000
drm/i915: Limit the busy wait on requests to 5us not 10ms!
But probably missed the comment since the change was non-local to the
comment.
v2: Polish comment more (Chris).
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470413484-23775-1-git-send-email-daniel.vetter@ffwll.ch
Fixes hangs under memory pressure, e.g. running the piglit test
tex3d-maxsize concurrently with other tests.
Fixes: 17d33bc9d6 ("drm/ttm: drop waiting for idle in ttm_bo_evict.")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No functional change. Instead of defining a new empty function
let's use what is available on drm.
It gets cleaner, and easy to read, and understand.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Copy to user return the number of bytes it couldn't write
and zero on success. So any number different than 0 should
be considered a fault, not only when it doesn't write
the full size.
v2: fixed the inverted logic. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
As pointed out by Chris Harris, we are using the wrong WA name, it
should in fact be WaToEnableHwFixForPushConstHWBug, also it should be
applied from C0 onwards for both BXT and KBL.
Fixes: 7b9005cd45 ("drm/i915: Add WaInsertDummyPushConstP for bxt and kbl")
Cc: Chris Harris <chris.harris@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-by: Chris Harris <chris.harris@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470127013-29653-1-git-send-email-matthew.auld@intel.com
In the previous commit, we moved the obj->tiling_mode out of a bitfield
and into its own integer so that we could safely use READ_ONCE(). Let us
now repair some of that damage by sharing the tiling_mode with its
companion, the fence stride.
v2: New magic
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-18-git-send-email-chris@chris-wilson.co.uk
Through the GTT interface to the fence registers, we can only handle
linear, X and Y tiling. The more esoteric tiling patterns are ignored.
Document that the tiling ABI only supports upto Y tiling, and reject any
attempts to set a tiling mode other than NONE, X or Y.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-17-git-send-email-chris@chris-wilson.co.uk
Since we are not concerned with userspace racing itself with set-tiling
(the order is indeterminant even if we take a lock), then we can safely
read back the single obj->tiling_mode and do the static lookup of
swizzle mode without having to take a lock.
get-tiling is reasonably frequent due to the back-channel passing around
of tiling parameters in DRI2/DRI3.
v2: Make tiling_mode a full unsigned int so that we can trivially use it
with READ_ONCE(). Separating it out into manual control over the flags
field was too noisy for a simple patch. Note that we could use the lower
bits of obj->stride for the tiling mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-16-git-send-email-chris@chris-wilson.co.uk
We don't need to incur the overhead of checking whether the object is
pinned prior to changing its madvise. If the object is pinned, the
madvise will not take effect until it is unpinned and so we cannot free
the pages being pointed at by hardware. Marking a pinned object with
allocated pages as DONTNEED will not trigger any undue warnings. The check
is therefore superfluous, and by removing it we can remove a linear walk
over all the vma the object has.
Still despite it being an overzealous check, that error code is part of
the current ABI and so we must proceed with caution.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-15-git-send-email-chris@chris-wilson.co.uk
We only need to take the struct_mutex if the object is pinned to the
display engine and so requires checking for clflush. (The race with
userspace pinning the object to a framebuffer is irrelevant.)
v2: Use access once for compiler hints (or not as it is a bitfield)
v3: READ_ONCE, obj->pin_display is not a bitfield anymore
v4: Don't be creative with goto.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-14-git-send-email-chris@chris-wilson.co.uk
By applying the same logic as for wait-ioctl, we can query whether a
request has completed without holding struct_mutex. The biggest impact
system-wide is removing the flush_active and the contention that causes.
Testcase: igt/gem_busy
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-13-git-send-email-chris@chris-wilson.co.uk
With a bit of care (and leniency) we can iterate over the object and
wait for previous rendering to complete with judicial use of atomic
reference counting. The ABI requires us to ensure that an active object
is eventually flushed (like the busy-ioctl) which is guaranteed by our
management of requests (i.e. everything that is submitted to hardware is
flushed in the same request). All we have to do is ensure that we can
detect when the requests are complete for reporting when the object is
idle (without triggering ETIME), locklessly - this is handled by
i915_gem_active_wait_unlocked().
The impact of this is actually quite small - the return to userspace
following the wait was already lockless and so we don't see much gain in
latency improvement upon completing the wait. What we do achieve here is
completing an already finished wait without hitting the struct_mutex,
our hold is quite short and so we are typically just a victim of
contention rather than a cause - but it is still one less contention
point!
v2: Break up a long line.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-12-git-send-email-chris@chris-wilson.co.uk
If we try and read or write to an active request, we first must wait
upon the GPU completing that request. Let's do that without holding the
mutex (and so allow someone else to access the GPU whilst we wait). Upon
completion, we will acquire the mutex and only then start the operation
(i.e. we do not rely on state from before the initial wait).
v2: Repaint the goto labels
v3: Move the tracepoints back to the start of the ioctls
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-11-git-send-email-chris@chris-wilson.co.uk
If we make the observation that mmap-offsets are only released when we
free an object, we can then deduce that the shrinker only creates free
space in the mmap arena indirectly by flushing the request list and
freeing expired objects. If we combine this with the lockless
vma-manager and lockless idling, we can avoid taking our big struct_mutex
until we need to actually free the requests.
One side-effect is that we defer the madvise checking until we need the
pages (i.e. the fault handler). This brings us into line with the other
delayed checks (and madvise in general).
v2: s/ret/err/ and use if (!err) rather than if (ret == 0)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-9-git-send-email-chris@chris-wilson.co.uk
We can now wait for the GPU (all engines) to become idle without
requiring the struct_mutex. Inside the shrinker, we need to currently
take the struct_mutex in order to purge objects and to purge the objects
we need the GPU to be idle - causing a stall whilst we hold the
struct_mutex. We can hide most of that stall by performing the wait
before taking the struct_mutex and only doing essential waits for
new rendering on objects to be freed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-8-git-send-email-chris@chris-wilson.co.uk
Now that we pass along the expected interruptible nature for the
wait-for-idle, we do not need to modify the global
i915->mm.interruptible for this single call. (Only the immediate call to
i915_gem_wait_for_idle() takes the interruptible status as the other
action, dma_map_sg(), is independent of i915.ko)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-7-git-send-email-chris@chris-wilson.co.uk
The principal motivation for this was to try and eliminate the
struct_mutex from i915_gem_suspend - but we still need to hold the mutex
current for the i915_gem_context_lost(). (The issue there is that there
may be an indirect lockdep cycle between cpu_hotplug (i.e. suspend) and
struct_mutex via the stop_machine().) For the moment, enabling last
request tracking for the engine, allows us to do busyness checking and
waiting without requiring the struct_mutex - which is useful in its own
right.
As a side-effect of having a robust means for tracking engine busyness,
we can replace our other busyness heuristic, that of comparing against
the last submitted seqno. For paranoid reasons, we have a semi-ordered
check of that seqno inside the hangchecker, which we can now improve to
an ordered check of the engine's busyness (removing a locked xchg in the
process).
v2: Pass along "bool interruptible" as being unlocked we cannot rely on
i915->mm.interruptible being stable or even under our control.
v3: Replace check Ironlake i915_gpu_busy() with the common precalculated value
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-6-git-send-email-chris@chris-wilson.co.uk
Before suspending (or unloading), we would first wait upon all rendering
to be completed and then disable the rings. This later step is a remanent
from DRI1 days when we did not use request tracking for all operations
upon the ring. Now that we are sure we are waiting upon the very last
operation by the engine, we can forgo clobbering the ring registers,
though we do keep the assert that the engine is indeed idle before
sleeping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-5-git-send-email-chris@chris-wilson.co.uk
We can completely avoid taking the struct_mutex around the non-blocking
waits by switching over to the RCU request management (trading the mutex
for a RCU read lock and some complex atomic operations). The improvement
is that we gain further contention reduction, and overall the code
become simpler due to the reduced mutex dancing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-3-git-send-email-chris@chris-wilson.co.uk
We can completely avoid taking the struct_mutex around the non-blocking
waits by switching over to the RCU request management (trading the mutex
for a RCU read lock and some complex atomic operations). The improvement
is that we gain further contention reduction, and overall the code
become simpler due to the reduced mutex dancing.
v2: Move i915_gem_fault tracepoint back to the start of the function,
before the unlocked wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-2-git-send-email-chris@chris-wilson.co.uk
It is useful to be able to wait on pending rendering without grabbing
the struct_mutex. We can do this by using the i915_gem_active_get_rcu()
primitive to acquire a reference to the pending request without
requiring struct_mutex, just the RCU read lock, and then call
i915_wait_request().
v2: Rebase onto new i915_gem_active_get_unlocked() semantics that take
the RCU read lock on behalf of the caller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-1-git-send-email-chris@chris-wilson.co.uk
Backmerge the 4.8 pull request state from Dave - conflicts were
getting out of hand, and Chris has some patches which outright don't
apply without everything merged together again.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The bspec was updated a couple weeks ago to add an extra block per line
to plane watermark calculations for linear pixel formats.
Bspec update 115327 description:
"Gen9+ - Updated the plane blocks per line calculation for linear
cases. Adds +1 for all linear cases to handle the non-block aligned
stride cases."
Cc: Lyude <cpaul@redhat.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470344880-27394-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Lyude <cpaul@redhat.com>
If the GEM objects being rendered with in this request have been
exported via dma-buf to a third party, hook ourselves into the dma-buf
reservation object so that the third party can serialise with our
rendering via the dma-buf fences.
Testcase: igt/prime_busy
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-26-git-send-email-chris@chris-wilson.co.uk
If we enable RCU for the requests (providing a grace period where we can
inspect a "dead" request before it is freed), we can allow callers to
carefully perform lockless lookup of an active request.
However, by enabling deferred freeing of requests, we can potentially
hog a lot of memory when dealing with tens of thousands of requests per
second - with a quick insertion of a synchronize_rcu() inside our
shrinker callback, that issue disappears.
v2: Currently, it is our responsibility to handle reclaim i.e. to avoid
hogging memory with the delayed slab frees. At the moment, we wait for a
grace period in the shrinker, and block for all RCU callbacks on oom.
Suggested alternatives focus on flushing our RCU callback when we have a
certain number of outstanding request frees, and blocking on that flush
after a second high watermark. (So rather than wait for the system to
run out of memory, we stop issuing requests - both are nondeterministic.)
Paul E. McKenney wrote:
Another approach is synchronize_rcu() after some largish number of
requests. The advantage of this approach is that it throttles the
production of callbacks at the source. The corresponding disadvantage
is that it slows things up.
Another approach is to use call_rcu(), but if the previous call_rcu()
is still in flight, block waiting for it. Yet another approach is
the get_state_synchronize_rcu() / cond_synchronize_rcu() pair. The
idea is to do something like this:
cond_synchronize_rcu(cookie);
cookie = get_state_synchronize_rcu();
You would of course do an initial get_state_synchronize_rcu() to
get things going. This would not block unless there was less than
one grace period's worth of time between invocations. But this
assumes a busy system, where there is almost always a grace period
in flight. But you can make that happen as follows:
cond_synchronize_rcu(cookie);
cookie = get_state_synchronize_rcu();
call_rcu(&my_rcu_head, noop_function);
Note that you need additional code to make sure that the old callback
has completed before doing a new one. Setting and clearing a flag
with appropriate memory ordering control suffices (e.g,. smp_load_acquire()
and smp_store_release()).
v3: More comments on compiler and processor order of operations within
the RCU lookup and discover we can use rcu_access_pointer() here instead.
v4: Wrap i915_gem_active_get_rcu() to take the rcu_read_lock itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-25-git-send-email-chris@chris-wilson.co.uk
We are motivated to avoid using a bitfield for obj->active for a couple
of reasons. Firstly, we wish to document our lockless read of obj->active
using READ_ONCE inside i915_gem_busy_ioctl() and that requires an
integral type (i.e. not a bitfield). Secondly, gcc produces abysmal code
when presented with a bitfield and that shows up high on the profiles of
request tracking (mainly due to excess memory traffic as it converts
the bitfield to a register and back and generates frequent AGI in the
process).
v2: BIT, break up a long line in compute the other engines, new paint
for i915_gem_object_is_active (now i915_gem_object_get_active).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-23-git-send-email-chris@chris-wilson.co.uk
Rather than a mismash of struct drm_device *dev and struct
drm_i915_private *dev_priv being used freely within a function, be
consistent and only pass along dev_priv.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-22-git-send-email-chris@chris-wilson.co.uk
The individual bits inside obj->frontbuffer_bits are protected by each
plane->mutex, but the whole bitfield may be accessed by multiple KMS
operations simultaneously and so the RMW need to be under atomics.
However, for updating the single field we do not need to mandate that it
be under the struct_mutex, one more step towards its removal as the de
facto BKL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-21-git-send-email-chris@chris-wilson.co.uk
We only need a very lightweight mechanism here as the locking is only
used for co-ordinating a bitfield.
v2: Move the cheap unlikely tests into the caller
v3: Move the kerneldoc into the header (now separated out into
intel_fronbuffer.h for better kerneldoc and readability)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtien <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-20-git-send-email-chris@chris-wilson.co.uk
In view of adding inline functions into the intel_frontbuffer section,
we first split the header into its own file so that we can integrate it
more easily with kerneldoc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-19-git-send-email-chris@chris-wilson.co.uk
Since i915_gem_obj_ggtt_pin() is an idiom breaking curry function for
i915_gem_object_ggtt_pin(), spare us the confusion and remove it.
Removing it now simplifies later patches to change the i915_vma_pin()
(and friends) interface.
v2: Add a redundant GEM_BUG_ON(!view) to
i915_gem_obj_lookup_or_create_ggtt_vma()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-18-git-send-email-chris@chris-wilson.co.uk
Not only is i915_vma_pin() called for every single object on every single
execbuf, it is usually a simple increment as the VMA is already bound for
execution by the GPU. Rearrange the tests for unbound and pin_count
overflow so that we can do the increment and test very cheaply and
compact enough to inline the operation into execbuf. The trick used is
to note that we can check for an overflow bit (keeping space available
for it inside the flags) at the same time as checking the binding bits.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-17-git-send-email-chris@chris-wilson.co.uk
In preparation to perform some magic to speed up i915_vma_pin(), which
is among the hottest of hot paths in execbuf, refactor all the bitfields
accessed by i915_vma_pin() into a single unified set of flags.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-16-git-send-email-chris@chris-wilson.co.uk
During execbuffer we look up the i915_vma in order to reserve them in
the VM. However, we then do a double lookup of the vma in order to then
pin them, all because we lack the necessary interfaces to operate on
i915_vma - so introduce i915_vma_pin()!
v2: Tidy parameter lists to remove one level of redirection in the hot
path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-15-git-send-email-chris@chris-wilson.co.uk
For consistency, internal functions should take drm_i915_private rather
than drm_device. Now that we are subclassing drm_device, there are no
more size wins, but being consistent is its own blessing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-12-git-send-email-chris@chris-wilson.co.uk
In order to be consistent with other address space functions, we want to
pass around 64-bit sizes, even though all known global GTT are limited
to 4GiB. Similarly, we are trying to be consistent in using the _ggtt_
nomenclature when referring to the special global GTT.
v2: Update docs to consistently state "global GTT".
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-11-git-send-email-chris@chris-wilson.co.uk
As we always allocate in chunks of 4096 (that being both the PAGE_SIZE
and our own GTT_PAGE_SIZE), we know that all results from the drm_mm are
aligned to at least 4096. The drm_mm allocator itself is optimised for
alignment == 0, and so by converting alignments of 4096 to 0 we can
satisfy our own requirements and still hit the faster path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-10-git-send-email-chris@chris-wilson.co.uk
Our GPUs impose certain requirements upon buffers that depend upon how
exactly they are used. Typically this is expressed as that they require
a larger surface than would be naively computed by pitch * height.
Normally such requirements are hidden away in the userspace driver, but
when we accept pointers from strangers and later impose extra conditions
on them, the original client allocator has no idea about the
monstrosities in the GPU and we require the userspace driver to inform
the kernel how many padding pages are required beyond the client
allocation.
v2: Long time, no see
v3: Try an anonymous union for uapi struct compatibility
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-7-git-send-email-chris@chris-wilson.co.uk
This is not the full fix, as we are required to percolate the u64 nature
down through the drm_mm stack, but this is required now to prevent
explosions due to mismatch between execbuf (eb_vma_misplaced) and vma
binding (i915_vma_misplaced) - and reduces the risk of spurious changes
as we adjust the vma interface in the next patches.
v2: long long casts not required for u64 printk (%llx)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-6-git-send-email-chris@chris-wilson.co.uk
Move the single line to the callsite as the name is now misleading, and
the purpose is solely to add the request to the execution queue. Here,
we can see that if we failed to dispatch the batch from the request, we
can forgo flushing the GPU when closing the request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-5-git-send-email-chris@chris-wilson.co.uk
This reimplements the denial-of-service protection against igt from
commit 227f782e46 ("drm/i915: Retire requests before creating a new
one") and transfers the stall from before each batch into get_pages().
The issue is that the stall is increasing latency between batches which
is detrimental in some cases (especially coupled with execlists) to
keeping the GPU well fed. Also we have made the observation that retiring
requests can of itself free objects (and requests) and therefore makes
a good first step when shrinking.
v2: Recycle objects prior to i915_gem_object_get_pages()
v3: Remove the reference to the ring from i915_gem_requests_ring() as it
operates on an intel_engine_cs.
v4: Since commit 9b5f4e5ed6 ("drm/i915: Retire oldest completed request
before allocating next") we no longer need the safeguard to retire
requests before get_pages(). We no longer see the huge latencies when
hitting the shrinker between allocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-4-git-send-email-chris@chris-wilson.co.uk
We should not rely on obj->active being uptodate unless we manually
flush it. Instead, we can verify that the next available batch object is
idle by looking at its last active request (and checking it for
completion).
v2: remove the struct drm_device forward declaration added in the
process of removing its necessity
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-3-git-send-email-chris@chris-wilson.co.uk
Slight micro-optimise to produce combine loops so that gcc is able to
optimise the inner-loops concisely. Since we are reviewing the loops, we
can update the comments to describe the current state of affairs, in
particular the distinction between evicting from the global GTT (which
may contain untracked items and transient global pins) and the
per-process GTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-1-git-send-email-chris@chris-wilson.co.uk
On Haswell/Broadwell, the HD-Audio block is inside the HDMI/display
power well and so the sna-hda audio codec acquires the display power
well while it is operational. However, Skylake separates the powerwells
again, but yet we still need the audio powerwell to setup the registers.
(But then the hardware uses those registers even while powered off???)
Acquiring the powerwell around setting the chicken bits when setting up
the audio channel does at least silence the WARNs from touching our
registers whilst unpowered. We silence our own test cases, but maybe
there is a latent bug in using the audio channel?
v2: Grab both rpm wakelock and audio wakelock
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135cebc "ALSA: hda - remove dependency on i915 power well for SKL")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Libin Yang <libin.yang@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1470240540-29004-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My ASUS PB278 at least doesn't seem to appreciate when you try to
ack sink irqs when there are none. Results in this sort of dmesg spam
[drm:drm_dp_dpcd_access] too many retries, giving up
Let's skip the ack if there are no pending irqs. I have no clue why we
do this in two places. One of them likely should just go away. Oh, and
MST has its own sink irq handler too...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to iterate the rates array in intel_dp_max_link_rate(). We know
the max rate will be the last entry, and we already know the size.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Manasi D Navare <manasi.d.navare@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With HSW + Dell UP2414Q (at least) drm_probe_ddc() occasionally fails,
and then we'll assume that the entire display has been disconnected.
We don't need the EDID from the main link, so we can simply check if
the sink is MST capable, and if so treat is as connected.
v2: Skip drm_probe_ddc() entirely for MST (Daniel)
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Manasi D Navare <manasi.d.navare@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1469800276-6979-1-git-send-email-ville.syrjala@linux.intel.com
s/active_mst_links/active_streams/ and use it also for SST. We can then
use this information in the hpd handling to see if the link is active
or not, and thus whether we may need to retrain.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Manasi D Navare <manasi.d.navare@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can't mix MST with SST/HDMI on the same physical port, so we'll need
to reject such configurations in check_digital_port_conflicts(). Nothing
else will prevent this as MST has its fake encoders and its own connectors
so the cloning checks won't catch this.
The same digital port can be used multiple times, but only if all the
encoders involved are MST encoders, so we only want to check MST vs.
SST/HDMI, not MST vs. MST. And SST/HDMI vs. SST/HDMI we already check.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The MST vs. SST selection should depend purely on the choice of the
connector/encoder. So don't try to determine the correct DDI mode
based on the intel_dp->is_mst, which simply tells us whether the sink
is in MST mode or not. Instead derive the information from the encoder
type. Since the link training code deals in non-fake encoders, we'll
also need to keep a second copy of that information around, which we'll
now designate as 'link_mst'.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge even more updates from Andrew Morton:
- dma-mapping API cleanup
- a few cleanups and misc things
- use jump labels in dynamic-debug
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dynamic_debug: add jump label support
jump_label: remove bug.h, atomic.h dependencies for HAVE_JUMP_LABEL
arm: jump label may reference text in __exit
tile: support static_key usage in non-module __exit sections
sparc: support static_key usage in non-module __exit sections
powerpc: add explicit #include <asm/asm-compat.h> for jump label
drivers/media/dvb-frontends/cxd2841er.c: avoid misleading gcc warning
MAINTAINERS: update email and list of Samsung HW driver maintainers
block: remove BLK_DEV_DAX config option
samples/kretprobe: fix the wrong type
samples/kretprobe: convert the printk to pr_info/pr_err
samples/jprobe: convert the printk to pr_info/pr_err
samples/kprobe: convert the printk to pr_info/pr_err
dma-mapping: use unsigned long for dma_attrs
media: mtk-vcodec: remove unused dma_attrs
include/linux/bitmap.h: cleanup
tree-wide: replace config_enabled() with IS_ENABLED()
drivers/fpga/Kconfig: fix build failure
Currently we re-read a bunch of static eDP panel caps from the DPCD
over and over again. Let's do it only once to save some time and effort.
v2: Make thing less confusing with intel_edp_init_dpcd() (Chris)
Move no_aux_handshake setup in there as well
v3: Move tps3/rate printout to intel_dp_long_pulse() so that
we'll still get them on eDP as well
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1469800359-7087-1-git-send-email-ville.syrjala@linux.intel.com
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonas spotted a discrepancy between the pwrite and pread ioctls, in
that pwrite takes the rpm wakelock around its GGTT access, The wakelock
is required in order for the GTT to function. In disregard for the
current convention, we take the rpm wakelock around the access itself
rather than around the struct_mutex as the nesting is not strictly
required and such ordering will one day be fixed by explicitly noting
the barrier dependencies between the GGTT and rpm.
Fixes: b50a53715f ("drm/i915: Support for pread/pwrite ...")
Reported-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1470298193-21765-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Erratum SKL075: Display Flicker May Occur When Both VT-d And FBC Are Enabled
"Display flickering may occur when both FBC (Frame Buffer Compression)
and VT - d (Intel® Virtualization Technology for Directed I/O) are enabled
and in use by the display controller."
Ville found the w/a name in the database:
WaFbcTurnOffFbcWhenHyperVisorIsUsed:skl,bxt and also dug out that it
affects Broxton.
v2: Log when the quirk is applied.
v3: Ensure i915.enable_fbc is false when !HAS_FBC()
v4: Fix function name after rebase
v5: Add Broxton to the workaround
Note for backporting to stable, we need to add
#define mkwrite_device_info(ptr) \
((struct intel_device_info *)INTEL_INFO(ptr))
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1470296633-20388-1-git-send-email-chris@chris-wilson.co.uk
Since commit de1add3605 ("drm/i915: Decouple execbuf uAPI from internal
implementation") the index of the engine (its engine->id) in the
internal list no longer matches the hardware id. However, in a couple of
locations we missed fixing up the difference. In this case,
RING_FAULT_REG() refers to engine->id which is now not what the register
offset actually should be. Fortunately, in both case we should be more
or less looping over 0..I915_NUM_ENGINES.
Fixes: de1add3605 ("drm/i915: Decouple execbuf uAPI from internal...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469643077-2523-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
If the fbdev probing fails, and in our error path we fail to clear the
dev_priv->fbdev, then we can try and use a dangling fbdev pointer, and
in particular a NULL fb. This could also happen in pathological cases
where we try to operate on the fbdev prior to it being probed.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468431285-28264-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 6bc265424d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit e9f24d5fb7.
The patch was only a stop-gap measure that fixed half the problem - the
leak of the fbcon when restarting X. A complete solution required
releasing the VMA when the object itself was closed rather than rely on
file/process exit. The previous patches add the VMA tracking necessary
to do close them along with the object, context or file, and so the time
has come to remove the partial fix.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-28-git-send-email-chris@chris-wilson.co.uk
When the user closes the context mark it and the dependent address space
as closed. As we use an asynchronous destruct method, this has two
purposes. First it allows us to flag the closed context and detect
internal errors if we to create any new objects for it (as it is removed
from the user's namespace, these should be internal bugs only). And
secondly, it allows us to immediately reap stale vma.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-27-git-send-email-chris@chris-wilson.co.uk
In order to prevent a leak of the vma on shared objects, we need to
hook into the object_close callback to destroy the vma on the object for
this file. However, if we destroyed that vma immediately we may cause
unexpected application stalls as we try to unbind a busy vma - hence we
defer the unbind to when we retire the vma.
v2: Keep vma allocated until closed. This is useful for a later
optimisation, but it is required now in order to handle potential
recursion of i915_vma_unbind() by retiring itself.
v3: Comments are important.
Testcase: igt/gem_ppggtt/flink-and-close-vma-leak
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-26-git-send-email-chris@chris-wilson.co.uk
Hook the vma itself into the i915_gem_request_retire() so that we can
accurately track when a solitary vma is inactive (as opposed to having
to wait for the entire object to be idle). This improves the interaction
when using multiple contexts (with full-ppgtt) and eliminates some
frequent list walking when retiring objects after a completed request.
A side-effect is that we get an active vma reference for free. The
consequence of this is shown in the next patch...
v2: Update inline names to be consistent with
i915_gem_object_get_active()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-25-git-send-email-chris@chris-wilson.co.uk
This patch is broken out of the next just to remove the code motion from
that patch and make it more readable. What we do here is move the
i915_vma_move_to_active() to i915_gem_execbuffer.c and put the three
stages (read, write, fenced) together so that future modifications to
active handling are all located in the same spot. The importance of this
is so that we can more simply control the order in which the requests
are place in the retirement list (i.e. control the order at which we
retire and so control the lifetimes to avoid having to hold onto
references).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-24-git-send-email-chris@chris-wilson.co.uk
If the object is active and we need to perform a relocation upon it, we
need to take the slow relocation path. Before we do, double check the
active requests to see if they have completed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-22-git-send-email-chris@chris-wilson.co.uk
If the user floods the GPU with so many requests that the engine stalls
waiting for free space, don't automatically promote the GPU to maximum
frequencies. If the GPU really is saturated with work, it will migrate
to high clocks by itself, otherwise it is merely a user flooding us with
busy-work.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-20-git-send-email-chris@chris-wilson.co.uk
By tracking each request occupying space inside an individual
intel_ring, we can greatly simplify the logic of tracking available
space and not worry about other timelines. (Each ring is an ordered
timeline of committed requests.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-17-git-send-email-chris@chris-wilson.co.uk
With the introduction of requests, we amplified the number of atomic
refcounted objects we use and update every execbuffer; from none to
several references, and a set of references that need to be changed. We
also introduced interesting side-effects in the order of retiring
requests and objects.
Instead of independently tracking the last request for an object, track
the active objects for each request. The object will reside in the
buffer list of its most recent active request and so we reduce the kref
interchange to a list_move. Now retirements are entirely driven by the
request, dramatically simplifying activity tracking on the object
themselves, and removing the ambiguity between retiring objects and
retiring requests.
Furthermore with the consolidation of managing the activity tracking
centrally, we can look forward to using RCU to enable lockless lookup of
the current active requests for an object. In the future, we will be
able to query the status or wait upon rendering to an object without
even touching the struct_mutex BKL.
All told, less code, simpler and faster, and more extensible.
v2: Add a typedef for the function pointer for convenience later.
v3: Make the noop retirement callback explicit. Allow passing NULL to
the init_request_active() which is expanded to a common noop function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-16-git-send-email-chris@chris-wilson.co.uk
Since we track requests, and requests are always added to the GPU fully
formed, we never have to flush the incomplete request and know that the
given request will eventually complete without any further action on our
part.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-15-git-send-email-chris@chris-wilson.co.uk
The future annotations will track the locking used for access to ensure
that it is always sufficient. We make the preparations now to present
the API ahead and to make sure that GCC can eliminate the unused
parameter.
Before: 6298417 3619610 696320 10614347 a1f64b vmlinux
After: 6298417 3619610 696320 10614347 a1f64b vmlinux
(with i915 builtin)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-12-git-send-email-chris@chris-wilson.co.uk
In the future, we will want to add annotations to the i915_gem_active
struct. The API is thus expanded to hide direct access to the contents
of i915_gem_active and mediated instead through a number of helpers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-11-git-send-email-chris@chris-wilson.co.uk
In the next patch, request tracking is made more generic and for that we
need a new expanded struct and to separate out the logic changes from
the mechanical churn, we split out the structure renaming into this
patch.
v2: Writer's block. Add some spiel about why we track requests.
v3: Now i915_gem_active.
v4: Now with i915_gem_active_set() for attaching to the active request.
v5: Use i915_gem_active_set() from inside the retirement handlers
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-10-git-send-email-chris@chris-wilson.co.uk
The drop_pages() function is a dangerous trap in that it can release the
passed in object pointer and so unless the caller is aware, it can
easily trick us into using the stale object afterwards. Move it into its
solitary callsite where we know it is safe.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-9-git-send-email-chris@chris-wilson.co.uk
When we call i915_vma_unbind(), we will wait upon outstanding rendering.
This will also trigger a retirement phase, which may update the object
lists. If, we extend request tracking to the VMA itself (rather than
keep it at the encompassing object), then there is a potential that the
obj->vma_list be modified for other elements upon i915_vma_unbind(). As
a result, if we walk over the object list and call i915_vma_unbind(), we
need to be prepared for that list to change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-8-git-send-email-chris@chris-wilson.co.uk
Since we may have VMA allocated for an object, but we interrupted their
binding, there is a disparity between have elements on the obj->vma_list
and being bound. i915_gem_obj_bound_any() does this check, but this is
not rigorously observed - add an explicit count to make it easier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-7-git-send-email-chris@chris-wilson.co.uk
For the global GTT (and aliasing GTT), the address space is owned by the
device (it is a global resource) and so the per-file owner field is
NULL. For per-process GTT (where we create an address space per
context), each is owned by the opening file. We can use this ownership
information to both distinguish GGTT and ppGTT address spaces, as well
as occasionally inspect the owner.
v2: Whitespace, tells us who owns i915_address_space
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-6-git-send-email-chris@chris-wilson.co.uk
Jyri Sarha