Error handling in UFS driver is broken and resets the host controller
for fatal errors without re-initialization. Correct the fatal error
handling sequence according to UFS Host Controller Interface (HCI)
v1.1 specification.
o Processed requests which are completed w/wo error are reported to
SCSI layer and any pending commands that are not started are aborted
in the controller and re-queued into scsi mid-layer queue.
o Upon determining fatal error condition the host controller may hang
forever until a reset is applied. Block SCSI layer for sending new
requests and apply reset in a separate error handling work.
o SCSI is informed about the expected Unit-Attention exception from the
device for the immediate command after a reset so that the SCSI layer
take necessary steps to establish communication with the device.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As of now SCSI initiated error handling is broken because,
the reset APIs don't try to bring back the device initialized and
ready for further transfers.
In case of timeouts, the scsi error handler takes care of handling aborts
and resets. Improve the error handling in such scenario by resetting the
device and host and re-initializing them in proper manner.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, sending Task Management (TM) command to the card might
be broken in some scenarios as listed below:
Problem: If there are more than 8 TM commands the implementation
returns error to the caller.
Fix: Wait for one of the slots to be emptied and send the command.
Problem: Sometimes it is necessary for the caller to know the TM service
response code to determine the task status.
Fix: Propogate the service response to the caller.
Problem: If the TM command times out no proper error recovery is
implemented.
Fix: Clear the command in the controller door-bell register, so that
further commands for the same slot don't fail.
Problem: While preparing the TM command descriptor, the task tag used
should be unique across SCSI/NOP/QUERY/TM commands and not the
task tag of the command which the TM command is trying to manage.
Fix: Use a unique task tag instead of task tag of SCSI command.
Problem: Since the TM command involves H/W communication, abruptly ending
the request on kill interrupt signal might cause h/w malfunction.
Fix: Wait for hardware completion interrupt with TASK_UNINTERRUPTIBLE
set.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Setting PA_PWRMode using DME_SET triggers the power mode
change. And then the result will be given by the HCS.UPMCRS.
This operation should be done atomically.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implements to support GET and SET operations of the DME.
These operations are used to configure the behavior of
the UNIPRO. Along with basic operation, {Peer/AttrSetType}
can be mixed.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Background operations in the UFS device can be disabled by
the host to reduce the response latency of transfer requests.
Add support for enabling/disabling the background operations
during runtime suspend/resume of the device.
If the device is in critical need of BKOPS it will raise an
URGENT_BKOPS exception which should be handled by the host to
make sure the device performs as expected.
During bootup, the BKOPS is enabled in the device by default.
The disable of BKOPS is supported only when the driver supports
runtime suspend/resume operations as the runtime PM framework
provides a way to determine the device idleness and hence BKOPS
can be managed effectively. During runtime resume the BKOPS is
disabled to reduce latency and during runtime suspend the BKOPS
is enabled to allow device to carry out idle time BKOPS.
In some cases where the BKOPS is disabled during runtime resume
and due to continuous data transfers the runtime suspend is not
triggered, the BKOPS is enabled when the device raises a level-2
exception (outstanding operations - performance impact).
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow UFS device to complete its initialization and accept
SCSI commands by setting fDeviceInit flag. The device may take
time for this operation and hence the host should poll until
fDeviceInit flag is toggled to zero. This step is mandated by
UFS device specification for device initialization completion.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As part of device initialization sequence, sending NOP OUT UPIU and
waiting for NOP IN UPIU response is mandatory. This confirms that the
device UFS Transport (UTP) layer is functional and the host can configure
the device with further commands. Add support for sending NOP OUT UPIU to
check the device connection path and test whether the UTP layer on the
device side is functional during initialization.
A tag is acquired from the SCSI tag map space in order to send the device
management command. When the tag is acquired by internal command the scsi
command is rejected with host busy flag in order to requeue the request.
To avoid frequent collisions between internal commands and scsi commands
the device management command tag is allocated in the opposite direction
w.r.t block layer tag allocation.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link start-up requires long time with multiphase handshakes
between UFS host and device. This affects driver's probe time.
This patch let link start-up run asynchronously. Link start-up
will be executed at the end of prove separately.
Along with this change, the following is worked.
Defined completion time of uic command to avoid a permanent wait.
Added mutex to guarantee of uic command at a time.
Adapted some sequence of controller initialization after link statup
according to HCI standard.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It makes interrupt setting more flexible especially
for disabling. And wrong bit mask is fixed for ver 1.0.
[17:16] is added for mask.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch separates PCI code from ufshcd.c and makes it as a
core driver module and adds a new file ufshcd-pci.c as PCI glue
driver.
[jejb: strip __devinit and devexit_p()]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sujit Reddy Thumma