The system to allow panel drivers to exists as attached to ctrl drivers
did never work very well. It is not useed, and this patch removes it to
make the driver cleaner.
For now, controller drivers need to include also the panel driver code. In
the future a proper mechanism for this should be developed, perhaps by
creating busses for controllers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When OMAP PM layer is no-op/debug, the PM layer will increment context
loss count with every call. This resulted DSS2 to restore context
whenever a clock was enabled.
This commit checks the context loss count only when the context actually
could have been lost, ie. when enabling a clock when no clocks had been
previously enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Instead of configuring only VC0 to be usable, configure all four VCs
similarly. This is needed to utilize the other VCs.
Setting the FIFO sizes evenly for all VCs, regardless of how many VCs are
actually used, is not optimal. However, this affects only cases when
larger amounts of data are written or read via L4, meaning that normal use
cases are not affected.
At some point this could be optimized better to suit different use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
dss_select_clk_source() was rather confusing. Selecting the source with
enums is much clearer.
The clk source selection is also stored into memory, so that we know what
is the selected source, even when clocks are off. This is important during
setup, as we need to what clocks to turn on before the clocks are turned
on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
It looks like on OMAP3 some DSS pins need VDDS_DSI to function properly.
This has not been confirmed from TI, but looking at figure 15-1 "Display
subsystem highlight" from the TRM, some data pins come near the DSI and SDI
blocks. This is not very hard evidence, but the fact remains that with the
power on, pixels are ok, and with the power off, pixels are not ok.
It may also be that VDDS_SDI is needed to power some pins, but as normally
both VDDS_SDI and VDDS_DSI come from the same power source, this hasn't
been shown.
It seems that a single driver can only get a regulator once. This patch
solves it by getting all the required regulators in one place, and from
which the submodules then get the regulators they need.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Loops checking for certain condition were rather inconsistent.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Collect interrupt statistics, printable via debugfs:
debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq
The counters are reset when printed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
- dsi_vc_send_short() needs to use dest_per for the peripheral id
- dsi_vc_send_null() was always using channel id 0
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tomi Valkeinen