Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb supports hardware encryption.
rt73usb supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not. The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.
Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes struct iwl4965_lq_mngr it is not used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_tbs is unsigned so the test doesn't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.
also remove priv->add_radiotap because it is not used any more.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.
renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).
add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).
setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.
the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables draft-802.11s Mesh Point operation. For that we need mesh
beaconing. Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To use these features, copy the boot2 and firmware images to /lib/firmware and:
echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively. Add more
suitable error codes for firmware programming process. Add capability checks
for persistent features before attempting to use them.
Based on patches from Brajesh Dave and Priyank Singh.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx/Rx descriptor flags are common between rtl818x devices, only with
additions for newer chips, thus use same flags in the code.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/b43/main.c
drivers/net/wireless/ipw2100.c
drivers/net/wireless/ipw2200.c
drivers/net/wireless/iwlwifi/iwl-3945.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-5000.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-eeprom.c
drivers/net/wireless/iwlwifi/iwl-hcmd.c
drivers/net/wireless/iwlwifi/iwl-power.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.
This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Only important for USB V1 Adaptors)
If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...
But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.
Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add newlines at printk outputs to not break dmesg.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for a Netgear WG111v3.
Signed-off-by: matthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 256b152b00 (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.
I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b19fa1f, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.
Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!
(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(I missed the fact that the original post said to apply this patch
twice... -- JWL)
Original commit log message:
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb_alloc produces linear packets (using kmalloc()). That can fail,
so should we fall back to making paged skbs.
My original version of this patch always allocate paged skbs for big
packets. But that made performance drop from 8.4 seconds to 8.8
seconds on 1G lguest->Host TCP xmit. So now we only do that as a
fallback.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a TUNGETIFF interface so that userspace can query a
tun/tap descriptor for its name and flags.
This is needed because it is common for one app to create
a tap interface, exec another app and pass it the file
descriptor for the interface. Without TUNGETIFF the spawned
app has no way of detecting wheter the interface has e.g.
IFF_VNET_HDR set.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the network stack can handle inbound packets with partial
checksums, we should no longer clobber the ip_summed field in the
loopback driver. This is because CHECKSUM_UNNECESSARY implies that
the checksum field is actually valid which is not true for loopback
packets since it's only partial (and thus complemented).
This allows packets from lo to then be SNATed to an external source
while still preserving the checksum's validity.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It hasn't been enabled for a long time and the generic GSO
engine is better documentation of what is expected of a
device implementing TSO.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables TSO since the loopback device is naturally
capable of handling packets of any size. This also means that
we won't enable GSO on lo which is good until GSO is fixed to
preserve netfilter state as netfilter treats loopback packets
in a special way.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.94.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool stats are 64-bits in length. net_device_stats members are
unsigned long types. When gathering information for
a get_ethtool_stats call, the driver will call a driver-private,
inlined get_stat64() function, which returns an unsigned long value.
This call will inadvertently mask off the upper 32-bits of a stat on
32-bit machines.
This patch defines a new get_estat() inline function and modifies the
ESTAT_ADD() macro to use it.
Signed-off-by: Stefan Buehler <stbuehler@web.de>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The git commit 7c5026aa9b ("tg3: Add
link state reporting to UMP firmware") introduced code that waits for
previous firmware events to be serviced before attempting to submit a
new event. Unfortunately that patch contained a bug that cause the
driver to wait 2.5 seconds, rather than 2.5 milliseconds as intended.
This patch fixes that bug.
This bug revealed that not all firmware versions service driver events
though. Since we do not know which versions of the firmware do and don't
service these events, the driver needs some way to minimize the effects
of the delay. This patch solves the problem by recording a jiffies
timestamp when it submits an event to the hardware. If the jiffies
counter shows that 2.5 milliseconds have already passed, a wait is not
needed and the driver can proceed to submit a new event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENABLE_ASF flag is set when DASH is enabled on the NIC, but DASH
does not run on the RX CPU. Instead it runs on the APE.
Consequently, the driver does not need to send "driver alive" updates
to the RX CPU when the APE is present.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's DASH (Desktop and mobile Architecture for System Hardware)
implementation requires that the driver preserve particular register
settings. If the driver does not preserve them, communication with
the DASH firmware will be lost.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, more status bits have been added to the APE status register.
This patch refines the status register check so that the driver can
send more events than it would have otherwise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver resets the chip while the APE is performing a register
access, that register access will never complete and the APE will hang
indefinitely. To prevent this race condition, the driver must acquire
an APE mutex before resetting the chip. The APE will not attempt a
register access until it acquires this lock.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases when ASF or other management firmware is running, the
chip may be configured to always strip out the VLAN tag even when
VLAN acceleration is not enabled. This causes some VLAN tagged
packets to be received by the host stack without any knowledge that
the original packet was VLAN tagged.
We fix this by re-inserting the VLAN tag into the packet when necessary.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should now be checking BNX2_FLAG_CAN_KEEP_VLAN to determine how
to set the VLAN rx tagging in the RX_MODE register.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a pair of nasty locking problems in the ax88796 driver
spotted by a sparse check:
warning: context imbalance in 'ax_get_settings' - wrong count at exit
warning: context imbalance in 'ax_set_settings' - wrong count at exit
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After some cleanups in arch/mips area, now MACH_TX49XX is selected for
both TOSHIBA_RBTX4927 and TOSHIBA_RBTX4938. Fold these two conditions
to one.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move the Kconfig for the new "Option" driver so it's not in the
middle of the usbnet-based drivers, so the dependency displays
in the Kconfig user interfaces don't get trashed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix up problems in hso.c driver as pointed out by Andrew.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As recommended by Arjan.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The references on ttyHSx devices were not decremented correctly when
the tty was closed. The helper freeing the serial devices was never
called because of that, and the module left some dangling sysfs
devices after being unloaded.
Signed-off-by: Olivier Blin <blino@mandriva.com>
Cc: Jari Tenhunen <jari.tenhunen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The tty may be closed already when the read/write callbacks are called.
This patch checks that the ttys still exist before waking them up.
Signed-off-by: Olivier Blin <blino@mandriva.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jari Tenhunen <jari.tenhunen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl()
is marked as "inline":
It's not used in any place where speed would matter much, and as long as
it has only one caller non-ancient gcc versions anyway inline it
automatically.
This patch fixes the following compile error with gcc 3.4:
<-- snip -->
...
CC drivers/net/atl1e/atl1e_main.o
atl1e_main.c: In function `atl1e_check_link':
atl1e_main.c:50: sorry, unimplemented: inlining failed in call to
atl1e_main.c:196: sorry, unimplemented: called from here
make[4]: *** [drivers/net/atl1e/atl1e_main.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark interrupt scheme in very old firmware incompatible. Interrupt mask
and status registers are per pci function / port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 does not require driver to kill dma watchdog.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Re-read link status in dev open(). Schedule link watchdog only
if dev is up.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Free up rx ring during driver unload or open() failure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031 mac addr should be read from firmware. mac addr in flash
is still valid, but can be overridden by firmware if running in
virtualization environment.
For old revisions, mac addr is retrieved directly from flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a simple device ID add for adapters that support
CX4 (copper infiniband style cable) connectors for 10GbE.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The removal of this bit of code was missed in an earlier patch submittal.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Setting an MTU value below 68 was disabling the network connection and
would not reconnect until the driver was reloaded. Prevent changing the
MTU to anything below 68.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prevent Tx hangs from happening on 10Mb flood ping by increasing the
timeout factor.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The e1000e driver was based on a version of e1000 prior to acme's
introduction of skb_copy_to_linear_data_offset, and was submitted
after acme went through and coverted all the drivers to use it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During module load, seting the InterruptThrottleRate parameter to an
invalid value would result in the itr/itr_setting pair being set to
unexpected values which would result in poor performance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A number of users have mentioned they have tools that rely on a link-up
indication having a return value of 1 rather than a non-zero value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Two regressions were introduced by the recent tlan: 64bit conversion
commit (93e16847c9). The first in
TLan_GetSKB caused a NULL pointer dereference. With the second causing
the link to fail to come up.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On my test box with the Asus M3A32-MVP main board there is a
regression from 2.6.26 related to suspend, hibernation and
shutdown. Namely, if Wake-on-LAN is enabled with
'ethtool -s eth0 wol g', the box hangs solid during all of these
operations, while executing either sky2_suspend(), or
sky2_shutdown(). This patch fixes it for me.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patch was generated using the Coccinelle semantic patch framework.
Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When myri10ge_fw_name is given, use it to override the rss firmware
name as well.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The arm ixp4xx_eth driver doesn't compile in 2.6.27-rc1:
CC [M] drivers/net/arm/ixp4xx_eth.o
drivers/net/arm/ixp4xx_eth.c: In function 'eth_poll':
drivers/net/arm/ixp4xx_eth.c:554: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:554: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'eth_xmit':
drivers/net/arm/ixp4xx_eth.c:701: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:701: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'init_queues':
drivers/net/arm/ixp4xx_eth.c:886: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:886: error: too few arguments to function 'dma_mapping_error'
make[3]: *** [drivers/net/arm/ixp4xx_eth.o] Error 1
make[2]: *** [drivers/net/arm] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
dma_mapping_error() changed in 2.6.27-rc1 to also take a device parameter,
but nobody bothered updating ixp4xx_eth.c. Fixed by passing the appropriate
device value in the dma_mapping_error() calls.
Tested on an ixp425 box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gfar_halt() was factored out into halting and disabling by commit
d87eb12785, as the suspend() method
only wants to do the former. However, the call to gfar_halt_nodisable()
from gfar_halt() apparently got lost during the patch respin process.
This adds it back.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
netns: Fix crash by making igmp per namespace
bnx2x: Version update
bnx2x: Checkpatch compliance
bnx2x: Spelling mistakes
bnx2x: Minor code improvements
bnx2x: Driver info
bnx2x: 1G LED does not turn off
bnx2x: 8073 PHY changes
bnx2x: Change GPIO for any port
bnx2x: Pause settings
bnx2x: Link order with external PHY
bnx2x: No LRO without Rx checksum
bnx2x: Wrong structure size
bnx2x: WoL capability
bnx2x: Clearing MAC addresses filters
bnx2x: Delay in while loops
bnx2x: PBA Table Page Alignment Workaround
bnx2x: Self-test false positive
bnx2x: Memory allocation
bnx2x: HW attention lock
...
Checkpatch compliance
The latest version of checkpatch found the following style errors in the
code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes
Spelling has to L's in it...
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1G LED does not turn off
The 1G LED was not switched to off when the link was lost
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl()
is marked as "inline":
It's not used in any place where speed would matter much, and as long as
it has only one caller non-ancient gcc versions anyway inline it
automatically.
This patch fixes the following compile error with gcc 3.4:
CC drivers/net/atl1e/atl1e_main.o
atl1e_main.c: In function `atl1e_check_link':
atl1e_main.c:50: sorry, unimplemented: inlining failed in call to
atl1e_main.c:196: sorry, unimplemented: called from here
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
Fix dubious logical operation that was found by sparse:
linux-next-20080807/drivers/net/bnx2x_main.c:7205:27: warning: dubious: !x & y
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these "magic" values must to be the other way round...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl_tx_skb function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is wrong to destroy a bonding master from a context that uses the sysfs
of that bond. When last IPoIB slave is unenslaved from by writing to a
sysfs file (for bond0 this would be /sys/class/net/bond0/bonding/slaves)
the driver tries to destroy the bond. This is wrong and can lead to a
lockup or a crash. This fix lets the bonding master stay and relies on
the user to destroy the bonding master if necessary (i.e. before module
ib_ipoib is unloaded)
This patch affects only bonds of IPoIB slaves. Ethernet slaves stay
unaffected.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Refactor mii monitor. As with the previous ARP monitor refactor,
the motivation for this is to handle locking rationally (in this case,
removing conditional locking) and generally clean up the code.
This patch breaks up the monolithic mii monitor into two phases:
an inspection phase, followed by an optional commit phase. The commit phase
is the only portion that requires RTNL or makes changes to state, and is
only called when inspection finds something to change.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some hardware set promisc when they are requested to set IFF_ALLMULTI flag.
It's ok, but if drivers set IFF_PROMISC flag when they set promisc,
it will broken upper layer handle for promisc and allmulti.
In addition, drivers can use their own hardware programming to make it.
So do not allow drivers to set IFF_* flags.
This is a general driver fix, so I didn't split it to pieces and send
to specific driver maintainers.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver reads the chip's MAC address from the attached EEPROM. When
no EEPROM is present, or when the MAC address is invalid, it falls back to
reading the address from the chip.
This patch lets platform code set the desired MAC address through platform
data.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix possible bug where end of receive buffer could be overwritten.
The allocation needs to allow for the reserved space. This would only happen
if device received packet greater than Ethernet standard MTU.
Change this driver to use netdev_alloc_skb rather than setting skb->dev
directly. For the initial allocation it doesn't need to be GFP_ATOMIC.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reference: https://launchpad.net/bugs/140511
The Belkin bluetooth dongle unfortunately shares the vendor and device id
with the network adapter which causes lockups whenever the bluetooth
dongle is inserted.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_read_direct':
drivers/net/netxen/netxen_nic_hw.c:1414: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_write_direct':
drivers/net/netxen/netxen_nic_hw.c:1487: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
You don't know what type was used for u64 hence they cannot be printed without
casting.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support SH7619 Internal ethernet controler.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Setup of the mac filter lost the upper 16bit of the mac address. This
bug got unconvered by a patch, which fixed the promiscous handling.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
xen-netfront never called netif_start_queue() and was was waking the
queue on xennet_open(), triggering the BUG_ON() on __netif_schedule().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver was erroneously clearing this bit though the hardware supports multicast.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This device is one side of a two-function adapter (NIC and iSCSI).
Promiscuous mode setting/clearing is not allowed from the NIC side.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, multicast filtering, promisc mode, and max frame size
setting is handled by firmware, driver needs to send request to
enable/disable it.
For old chip revisions / firmware, driver still sets it directly.
Added function pointer to set mtu according to chip revision.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Initialize producer and consumer indices during netdev open(), only
for old firmware/chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix legacy interrupt mode for NX3031 chips, read pci interrupt state
in hardware to guard against spurious interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add couple of new board configurations based on NX3031 chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, the phy is managed by firmware, so driver should avoid
setting any phy registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The commit that made the CONFIG_GFAR_NAPI code unconditional was
included at the same time as a new CONFIG_GFAR_NAPI user, resulting
in these bugus #ifdef's.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently when we do a packet flood to the Ethernet port, the console
reports error every time when a packet is dropped. This is too
redundant and cost performance. Remove message for this type of event.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for limiting the number of tx pause frames to a
default of 8. Previously, hardware would send out continuous stream of
pause frames.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds jumbo frame support for MCP79 chipsets.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for new tx statistic counters in the hardware -
unicast, multicast, and broadcast
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enforces a stricter policy on rx errors. The driver needs to
verify whether there are multiple rx errors versus a single error.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host. This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three functions were left in the code that are no longer used. I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The L1 hardware contains a bug that flags a fragmented IP packet
as having an incorrect TCP/UDP checksum, even though the packet
is perfectly valid and its checksum is correct. There's no way to
distinguish between one of these good packets and a packet that
actually contains a TCP/UDP checksum error, so all we can do is
allow the packet to be handed up to the higher layers and let it
be sorted out there.
Add a comment describing this condition and remove the code that
currently fails to handle what may or may not be a checksum error.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.
The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set 64bits consistent DMA mask since it improves performance
in some cases. No need to check the return value since it is
not required for the driver to work.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (78 commits)
AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE
pktgen: mac count
pktgen: random flow
bridge: Eliminate unnecessary forward delay
bridge: fix compile warning in net/bridge/br_netfilter.c
ipv4: remove unused field in struct flowi (include/net/flow.h).
tg3: Fix 'scheduling while atomic' errors
net: Kill plain NET_XMIT_BYPASS.
net_sched: Add qdisc __NET_XMIT_BYPASS flag
net_sched: Add qdisc __NET_XMIT_STOLEN flag
iwl3945: fix merge mistake for packet injection
iwlwifi: grap nic access before accessing periphery registers
iwlwifi: decrement rx skb counter in scan abort handler
iwlwifi: fix unhandled interrupt when HW rfkill is on
iwlwifi: implement iwl5000_calc_rssi
iwlwifi: memory allocation optimization
iwlwifi: HW bug fixes
p54: Fix potential concurrent access to private data
rt2x00: Disable link tuning in rt2500usb
iwlwifi: Don't use buffer allocated on the stack for led names
...
This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code").
The first hunk of the patch removes an unnecessary
tg3_set_power_state() call. The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().
The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions. The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (29 commits)
sh: enable maple_keyb in dreamcast_defconfig.
SH2(A) cache update
nommu: Provide vmalloc_exec().
add addrespace definition for sh2a.
sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
sh: define GENERIC_HARDIRQS_NO__DO_IRQ.
sh: define GENERIC_LOCKBREAK.
sh: Save NUMA node data in vmcore for crash dumps.
sh: module_alloc() should be using vmalloc_exec().
sh: Fix up __bug_table handling in module loader.
sh: Add documentation and integrate into docbook build.
sh: Fix up broken kerneldoc comments.
maple: Kill useless private_data pointer.
maple: Clean up maple_driver_register/unregister routines.
input: Clean up maple keyboard driver
maple: allow removal and reinsertion of keyboard driver module
sh: /proc/asids depends on MMU.
arch/sh/boards/mach-se/7343/irq.c: removed duplicated #include
arch/sh/boards/board-ap325rxa.c: removed duplicated #include
sh/boards/Makefile typo fix
...
We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements rssi calculation for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family
The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn