During testing with AMPDUs it turned out that the rt2800 hw will aggregate
consecutive frames with the same RA and TID when the first frame in a
possible aggregate has set AMPDU=1 in the TXWI. If a following frame has
set AMPDU=0 in its TXWI it might sill end up in the aggregate of the
previous frame. Update the comment accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX_STA_FIFO contains some information for identifying
a outgoing frame, however matching by WCID and ACK status is
not sufficient to 100% identify the macthing queue_entry structure
(containing the SKB buffer) which belongs to the status report.
Within TX_STA_FIFO we have a 4-bit field named PACKETID, which is
currently used to encode the queue id. The queue ID is however
limited to values from 0 to 3, which means 2 bits are sufficient
to encode the value. With the remaining 2 bits we can encode a
partial queue_entry index number. The value of PACKETID is not
allowed to become 0, with the queue ID ranging from 0 to 3, at least
one of the bits for the entry identification must be 1.
That leaves us with 3 possible values we can still encode in the
bits. Altough this doesn't allow 100% accurate matching of the
TX_STA_FIFO queue to a queue_entry structure, it at least improves
the accuracy. This allows us to better detect if we have missed the
TX_STA_FIFO report, which in turn reduces the number of watchdog
warnings regarding the TX status timeout.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci and rt2800 devices can use up to 7 different rates per tx frame.
However, the device uses a global fallback table. Hence, the rc
algortihm cannot specify multiple rates to try but the device is able to
report multiple rates (based on the retry table). Specify that behavior
by correctly setting max_report_rates and max_rates.
This makes rt2x00 and minstrel play nicer together.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rt2x00 USB devices have no chance to know when a beacon was sent
out in AP mode currently all broad- and multicast traffic is buffered in
mac80211 but never sent out at all.
Unfortunately we have no chance in sending the traffic out after a
DTIM beacon due to hw limitations. Hence, instead of never sending the
buffered traffic out better send it out immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the register definition CH_BUSY_STA_SEC for reading the busy time
on the secondary channel in HT40 mode. Also update the comments about
channel busy/idle time registers to express the used unit.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a
transmission with legacy rates to both 20Mhz channels if set.
Also update the related comment in rt2800.h to describe the
behavior of the BW_40 flag for legacy rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX
descriptor. At that time the skb is already dma unmapped but no new skb
was dma mapped for this entry again. However, rt2800pci_fill_rxdone also
moves the hw rx queue index, marking this entry to be available for
reuse. Since no new skb was dma mapped and also the previous skb was
unmapped this might lead to strange hw behavior.
To fix this issue move the hw rx queue index increment to
rt2800pci_clear_entry where a new skb was already dma mapped and can be
safely used by the hw.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HT protection is now configurable via mac80211 we don't need this
special case for PCI devices anymore. The HT protection config will be
overwritten as soon as mac80211 sends us a HT operation mode. Hence,
bring the HT MM40 protection config in sync with the other HT protection
registers and initialize it to no protection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a check for dynamic SM PS mode in the STAs HT caps. Since a
value of 3 means "SM PS disabled" the previous check assumed in
that case that "dynamic SM PS" was enabled and as such prefixed
every MCS>7 frame with a unnecessary RTS/CTS exchange. Also,
the bit shift was done in the wrong direction.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.
To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.
To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.
In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.
One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.
Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices use parts of the pariwise key table to store the beacon
frames for beacon 6 and 7. To not overwrite the beacon frame buffers
limit the number of entries we store in the pairwise key table to 222.
Also add some descriptive comments about this shared memory usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Includes pkts/bytes that may have had errors, and includes
wireless headers when counting bytes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds counters for tx and rx bytes, including any
errored packets as well as all wireless headers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org [all]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support up to 4 virtual APs and as many virtual STA interfaces
as desired.
This patch is ported forward from a patch that Patrick McHardy
did for me against 2.6.31.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can start restarting firmware or RF kill switch can be turned on
during call to iwl_mac_add_interface(). That are normal working
conditions, so do not print call trace, just print simple message
instead.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The combined firmware ar9170.fw is preferred and supports all devices.
References to the older two-stage firmware are unnecessary.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
common->ani.noise_floor is now only used for a similar redundant debug
message similar to the one that was removed from ath9k_htc in an earlier
patch. Remove it from ath9k as well now.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused aside from a single redundant debug message
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware rx-filter was essentially disabled, because
of a serve, yet unidentifiable problem with iwlagn.
Due to these circumstances the driver and mac80211 were
left with the job of filtering.
This is very unfortunate and has proven to be expensive
in terms of latency, memory and load.
Therefore the new 1.8.8.3 firmware introduces a flexible
filtering infrastructure which allows the driver to
offload some of the checks (FCS & PLCP crc check,
RA match, control frame filter, etc...) whenever possible.
Note:
This patch also includes all changes to the
shared headers files since the inclusion.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One __attribute__ ((packed)) has been accidentally introduced in commit
be86cbea1e. This patch changes it to __packed.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently a command to initialize extended radio parameter tables in the
hardware is missing.
Add the initialization
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
In the event of a hardware failure, reconfiguring a live connection back
with the wl1271 chip does not work as expected. The chip has management
features which require setting up the association from scratch to work
correctly. To ensure this is done every time, in managed mode, when associated,
indicate connection loss to the mac80211 before asking to reconfigure the
hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Due to legacy reason, dating back to when the wl1251 and wl1271 still were
a unified driver, some work-structures are initialized on hardware startup.
The hardware recovery code creates a scenario in which it is possible for a
workstruct to be re-initialized while the work-function itself is running,
which causes a kernel WARNing and a subsequent reboot.
To remedy this, move the work initialization calls to the hw allocation,
which is the logically correct place for them anyway.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of sending one packet at a time to the firmware, try to
send all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of retrieving one packet at a time from the firmware, try to
retrieve all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The HW supports up to 4095 bytes transfers via SPI. The SPI read & write
operations do not handle larger transfers, causing the HW to stall in such
cases.
Fix this by fragmenting large transfers into smaller chunks, and
transferring each one separately.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Do this instead of subverting fields in skb proper.
The macros that could very easily match variable or function
names were also just asking for trouble.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make wimax variables and functions local if possible.
Compile tested only.
This also removes a couple of unused EXPORT_SYMBOL.
If this breaks some out of tree code, please fix that
by putting the code in the kernel tree.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has several pieces of dead code (found by running
make namespacecheck). This patch removes them.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel doesn't have a symbol called BCM63XX. There is a symbol
BCM63XX_ENET (introduced in 9b1fc55a05, 6 weeks after 09bb9aa0ed that
introduced BCM63XX_PHY), but the driver compiles without that, too.
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting mtu < 68 is not supported.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mode setting is not required for Qlogic CNA adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o desc->vlan_tci is in __le16 format. Doing htons and
cpu_to_le64 again on vlan_tci, result in invalid value on ppc.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipaddress in ifa->ifa_address field are in big endian format.
Also device requires ip address in big endian only.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
regs_buff[i] and diag_registers[j] array should use different index
variable.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the counters are not implemented in fw.
Fw return NOT AVAILABLE VALUE as (0xffffffffffffffff).
Adding these counters, result in invalid value.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loop 10 times with delay of 1 ms to rcv packet.
o Print garbage packet.
o Try send/receive MAX(16) packet, instead of exit from test,
if a packet is not received.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
vlan: dont drop packets from unknown vlans in promiscuous mode
Phonet: Correct header retrieval after pskb_may_pull
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
ip_gre: Fix dependencies wrt. ipv6.
net-2.6: SYN retransmits: Add new parameter to retransmits_timed_out()
iwl3945: queue the right work if the scan needs to be aborted
mac80211: fix use-after-free
This patch adds multiple RX queue support to be2net. There are
upto 4 extra rx-queues per port into which TCP/UDP traffic can be hashed into.
Some of the ethtool stats are now displayed on a per queue basis.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bogus PCI function number check from the driver's .remove
method that causes pci_release_regions not to be called for function 0
if additional functions are attached and one of them is used as primary.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: trailing statements should be on next line
#23: FILE: drivers/net/tulip/de4x5.c:5477:
+ if (copy_to_user(ioc->data, tmp.lval, ioc->len)) return -EFAULT;
total: 1 errors, 0 warnings, 8 lines checked
./patches/drivers-net-tulip-de4x5c-fix-copy-length-in-de4x5_ioctl.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'select' ignores dependencies, drivers that select INET_LRO must
depend on INET. This fixes the broken configuration reported in
<http://article.gmane.org/gmane.linux.kernel/825646>.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions used locally in a file as static
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed code that is unused
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.114.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the rx ring sizes for those asic revs that support
them.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new variables to track the size of the standard and
jumbo rx producer ring sizes. The code is then pivoted to these
variables from preprocessor constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are other multiqueue modes 5717 and 5719 devices can assume. This
patch makes sure that the loopback test is safe, should those other
modes be enabled in the future.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the default VPD partno section. New entries for
5717 asic rev devices were also added.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product was never released to the public.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables a bit that prevents read DMA overflows and adjusts
the txmbuf margin from the hardware default. The combination of these
modifications prevents a tx data corruption issue we were seeing on the
5719.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the tg3 driver would call netif_napi_add() for the maximum
number of NAPI instances the driver could use. The problem is that
netpoll could call tg3_poll() on instances that are not active. The net
effect is that the driver will crash attempting to dereference
uninitialized pointers.
The fix is to only allocate as many NAPI instances as the driver would
use in tg3_open() and deleted them in tg3_close().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial support for 82579 was tuned poorly for performance. Adjust the
packet buffer allocation appropriately for both standard and jumbo frames;
and for jumbo frames increase the receive descriptor pre-fetch, disable
adaptive interrupt moderation and set the DMA latency tolerance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most e1000e parts support batching writebacks. The problem with this is
that when some of the TADV or TIDV timers are not set, Tx can sit forever.
This is solved in this patch with write flushes using the Flush Partial
Descriptors (FPD) bit in TIDV and RDTR.
This improves bus utilization and removes partial writes on e1000e,
particularly from 82571 parts in S5500 chipset based machines.
Only ES2LAN and 82571/2 parts are included in this optimization, to reduce
testing load.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible panic/hang with shared Legacy interrupts by not enabling
interrupts when interface is down.
Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr()
This patch adds flags to ixgbe_irq_enable() to allow for some flexibility
when enabling interrupts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Sachin Sanap <ssanap@marvell.com>
Signed-off-by: Mark Brown <markb@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be ready after 8 years...remove the experimental dependency.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print media debug messages only when HW debug is enabled.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following DCA improvements to myri10ge:
1) Finally move myri10ge to use dca3 API
2) Disable PCIe relaxed ordering when enabling DCA on
myri10ge. This provides a performance boost on Nehalem
based Xeons
3) Make sure to properly initialize NIC's DCA state when it is enabled,
rather than giving the NIC a bogus tag (0) and waiting for
the first received packet to trigger an update. Not using a
real tag can cause hardware exceptions on some motherboards
when a CPU socket is empty.
3) Always update the cached CPU when our interrupt affinity changes
so as to avoid excessive calls to dca3_get_tag()
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved enabling of MSI to the bnx2x_set_num_queues() - the same functions that
handles the initialization of the MSI-X.
From: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since uCode is responsible for doing DC calibration, there's no need
to let init uCode to do initial DC calibration then send results
back to driver, then driver sends the results to runtime uCode.
Driver can simply tell runtime uCode to do DC calibration.
Actually, this patch does not disable DC calib for init uCode. It just
prevent driver from saving and sending the DC calib results (from init
ucode) to runtime uCode. The driver still uses 0xffffffff in
CALIB_CFG_CMD for init ucode.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For 6050g2 devices driver needs to set a special bit to CSR register
so that uCode can do things correctly in calibration routines.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi driver supports multiple devices. Since some device needs
special configuration we create a new iwl_nic_ops structure which is
configurable per device. Currently there is only one function pointer
inside this structure: additional_nic_config().
The iwl_nic_ops structure is added to the top level in struct iwl_ops,
making it easier to change per device. Duplication of the iwl_lib_ops
structure is no longer needed.
With this new ops the previous function pointer set_calib_version is
no longer needed since it is just a per device nic configuration.
As part of the code restructuring, a bug is addressed. Indication of
calib version to uCode is only needed for 6050 devices, however,
current implementation set calib version for all 6000 devices for
which DC calib is needed. To fix this, create iwl6050_ops for 6050
devices and only populate iwl_nic_ops in this structure.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
add new structures and defines need to identify 100 devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch fixes a bug in the driver which was
exposed by CONFIG_USB_DEBUG:
"usb 1-1.6.3: BOGUS urb flags, 40 --> 0"
The transfer flag "URB_ZERO_PACKET" is only valid
for bulk urbs.
Reported-by: André Erdmann
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Ryan Niemi, some bitmasks in the register definition for the PCU
Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix
some typos and add more comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in ath5k_hw_get_tsf64() is time critical and will return wrong results
if we get interrupted, so disable local interrupts.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use FUDGE to make sure the next TBTT is ahead of the current TU.
Since we later substract AR5K_TUNE_SW_BEACON_RESP (10) in the timer
configuration we need to make sure it is bigger than that.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not used and it's unlikely we will ever implement ATIM.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Miller complained about the driver's excessive use
of variables in __packed structs. While I did not fully
agree with his sole "performance" argument on all accounts.
I do see some room for improvement in hot-paths on
architectures without an efficient access to unaligned
elements.
This first patch (dare I say?) optimizes an important tx
hot-path in the driver: carl9170_tx_prepare.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom's Windows driver for the 4313 advertises
an ampdu density of 7 => 16 us. The AR9170 MAC on
the other hand only supports densities up to 8 us.
This patch removes the noisy WARN_ON, because
there is nothing we can do about it.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx_ampdu_upload was not decreased when an a-MPDU
frame had to be kicked out from the tx_pending
queues.
This broke ampdu aggregation, because the scheduler
waits until tx_ampdu_upload drops to zero, before
making the next aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes some cruft, which survived
the RFC review phase.
Originally, carl9170_tx_ampdu_queue erroneously
dropped a lot of frames. As a result the ampdu
scheduler bogged down quite frequently and the
affected BA session timed out.
However this bug has been fixed and the WA and
its debugfs counter is no longer useful.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"The convention seems to be angle brackets around
URLS in Kconfig."
-- Finn Thain (to update web addresses in the kernel)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11n-2009 demands in 11.2.1: "
When a STA enters normal (non-APSD) PS mode, any downlink
Block ACK agreement without an associated schedule is
suspended for the duration of this PS mode."
The operative word is "suspended" and not terminated.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945's scan_completed calls into the mac80211 stack which triggers a
warn on if there is no scan outstanding.
This can be avoided by not calling scan_completed but abort_scan in
iwl3945_request_scan in the done: branch of the function which is used
as an error out.
The done: branch seems to be an error-out branch, as, for example, if
iwl_is_ready(priv) returns false the done: branch is executed.
NOTE:
I'm not familiar with the driver at all.
I just quickly scanned as a reaction to
https://bugzilla.kernel.org/show_bug.cgi?id=17722
the users of scan_completed in the iwl3945 driver and noted the odd
discrepancy between the comment above this instance and the comment in
mac80211 scan_completed function.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
tcp: Fix >4GB writes on 64-bit.
net/9p: Mount only matching virtio channels
de2104x: fix ethtool
tproxy: check for transparent flag in ip_route_newports
ipv6: add IPv6 to neighbour table overflow warning
tcp: fix TSO FACK loss marking in tcp_mark_head_lost
3c59x: fix regression from patch "Add ethtool WOL support"
ipv6: add a missing unregister_pernet_subsys call
s390: use free_netdev(netdev) instead of kfree()
sgiseeq: use free_netdev(netdev) instead of kfree()
rionet: use free_netdev(netdev) instead of kfree()
ibm_newemac: use free_netdev(netdev) instead of kfree()
smsc911x: Add MODULE_ALIAS()
net: reset skb queue mapping when rx'ing over tunnel
br2684: fix scheduling while atomic
de2104x: fix TP link detection
de2104x: fix power management
de2104x: disable autonegotiation on broken hardware
net: fix a lockdep splat
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
...
Fix build errors, more header files needed.
drivers/net/pch_gbe/pch_gbe_main.c:965: error: implicit declaration of function 'tcp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:965: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:968: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:976: error: implicit declaration of function 'udp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:976: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:980: error: invalid type argument of '->' (have 'int')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this go away (happens when building with a separate object
directory):
Assembler messages:
Fatal error: can't create drivers/net/wireless/wl12xx/.tmp_wl12xx_platform_data.o: No such file or directory
drivers/net/wireless/wl12xx/wl12xx_platform_data.c: In function 'wl12xx_get_platform_data':
drivers/net/wireless/wl12xx/wl12xx_platform_data.c:28: error: cannot open drivers/net/wireless/wl12xx/.tmp_wl12xx_platform_data.gcno
drivers/net/wireless/wl12xx/wl12xx_platform_data.c:28: confused by earlier errors, bailing out
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
This patch improves connection reliability by choosing the lowest basic
rate for null-func frames (which increases their range, as the firmware does
not do rate fall-back for null-func frames.) Also, increase the PSM entry
retry-counter.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently then dwell times for each channel in scans is set to an overly
long value, and excessive number of probe-requests are transmitted on each
channel (for active scans.)
Based on testing, comparable results can be received with smaller dwell-time,
and, with fever probe-requests - in fact, reducing the number of probe-requests
to 2 seems to increase the number of found results.
Configure more optimal values for per channel dwell times. Comparison for the
different scan configurations (in my current office environment):
dwell-time 60000 3x probe-req == ~60 results
40000 3x probe-req == ~50 results
30000 3x probe-req == ~40 results
dwell-time 60000 2x probe-req == ~70 results
40000 2x probe-req == ~60 results
30000 2x probe-req == ~58 results
The above are results for a cumulative 3 scan run. For individual scans, the
number of results drop slightly more.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently, the driver does not handle a failing hardware command to scan in
any way - effectively, the scan machine will jam until the driver is shut down,
and future scan requests will just return -EBUSY to user space, resulting in
a type of busy-loop. The same problem occurs if the firmware fails to deliver
the scan completion event - add timeout for this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
There is some probability of hardware failures, which currently go largely
undetected. Attempt to recover from these failures by shutting down the
hardware, and requesting mac80211 to reconfigure it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Do this so the interface removal can be triggered from an upcoming hardware
failure recovery mechanism.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The work cancelling has had several hazards, ranging from potentially
executing work after the driver is in OFF state, to executing work after
the driver and relevant memory structures are already removed.
Fix these.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The current scan implementation can jam, if the scan request ends up
containing no work. This can especially happen if there is a scan request
with only 11a band channels for HW that does not support 11a.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Incorrect TID was configured for TX frames. This resulted in incorrect
queues to be used for classes in transmission.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This patch always enables 11a band towards the mac80211, but prevents scanning
(and hence the usage of) 11a band channels if the chipset does not support it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This patch reduces the rate of the null-func used to enter PSM on the last
retry as precaution.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of hardcoding 11a support, enable/disable driver support based on
the dual-mode-select parameter in the nvs-file general paramters.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The function is not used anywhere.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The current order causes driver releasing to fail in various ways, and causes
possible instability.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This removes a fixme. Also, it removes a redundant setting of the wake-up
conditions when exiting power save mode, which should improve performance.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The mac80211 inserts channels into a scan request in the same order the driver
registers them. Use this fact to optimize scan by ordering the channels so
that adjacent channels don't get scanned consecutively.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
When we get no SSIDs in the scan request, we should force a passive scan in
all channels. This patch adds code to force the passive scan flag to be set
in that case.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
This code was a leftover of the previous scanning mechanism. The if is
totally unnecessary, since both branches do the same thing.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
In the scan state machine, the wl1271_mutex is unlocked first then relocked,
and then the scan state variables are modified.
This makes it possible for ieee80211_scan_complete to be called twice in some
scenarios, as the scan completion event from the firmware may be processed
while the mutex is unlocked.
To fix the issue, move the ieee80211_scan_complete call last in the function.
This is generally safer, but there still may be issues is functions calling
the scan state machine rely on states checked before the unlocking of the
global mutex.
(forward ported from 2.6.32 -- this is not strictly needed anymore, because
the mutex doesn't need to be unlocked anymore, but I'm applying this change
anyway, so that the call to ieee80211_scan_complete is in the same place)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Add a trigger to net_device changes to monitor for oper_state changes in order
to be able to inform the firmware when association is fully complete (including
the EAP negotiation.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Implement the command function to send CMD_SET_STA_STATE to the firmware. This
is used to indicate that association (and the related EAP negotiation) are
complete.
This is used to tune WLAN-BT coexistense priority towards BT, improving BT
A2DP and SCO performance.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
As of Rev. 6.1.0.0.335, the ACX_SET_SMART_REFLEX_DEBUG command is
deprecated. This patch removes it from the wl1271 driver (it wasn't used
anyway).
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set num_tx_queues or real_num_tx_queues, since
alloc_etherdev_mq() does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is up, using ethtool breaks it because:
a) link is put down but media_timer interval is not shortened to NO_LINK
b) rxtx is stopped but not restarted
Also manual 10baseT-HD (and probably FD too - untested) mode does not work -
the link is forced up, packets are transmitted but nothing is received.
Changing CSR14 value to match documentation (not disabling link check) fixes this.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit removed splitmic. But forgot to add
ATH_CRYPT_CAP_MIC_COMBINED flag for HTC drivers which causes
TKIP to fail.
Author: Bruno Randolf <br1@einfach.org>
Date: Wed Sep 8 16:04:54 2010 +0900
ath/ath9k: Replace common->splitmic with a flag
Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old ieee80211_find_sta_by_hw method didn't properly
find VIFS when there was more than one per AP. This caused
AMPDU logic in ath9k to get the wrong VIF when trying to
account for transmitted SKBs.
This patch changes ieee80211_find_sta_by_hw to take a
localaddr argument to distinguish between VIFs with the
same AP but different local addresses. The method name
is changed to ieee80211_find_sta_by_ifaddr.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9287 v1.0 was never sold (and the initvals removed), its revision
checks can be simplified similar to AR9280
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9285 v1.0 and v1.1 were never sold (and the initvals removed),
its revision checks can be simplified similar to AR9280
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9280 v1.0 was never sold (and the initvals removed), v1.0 specific
revision checks can be removed and the 'v2.0 or later' check can be
simplified to a check for AR9280 or later.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to miscalculation of nvs_len, excessive data was sent to the
firmware.
Fix this by first setting nvs_ptr to point to the first NVS table,
and computing the total size of all NVS tables accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-By: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (commit 690a1f2002) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via
vortex_set_wol+0xcd/0xe0 [3c59x]
dev_ethtool+0xa5a/0xb70
dev_ioctl+0x2e0/0x4b0
T.961+0x49/0x50
sock_ioctl+0x47/0x290
do_vfs_ioctl+0x7f/0x340
sys_ioctl+0x80/0xa0
system_call_fastpath+0x16/0x1b
i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.
Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.
In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
loopback driver uses dev->ml_priv to store its percpu stats pointer.
It uses ugly casts "(void __percpu __force *)" to shut up sparse
complains.
Define an union to better document we use ml_priv in loopback driver and
define a lstats field with appropriate types.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function to resize the Tx/Rx rings had the potential to
dereference a NULL pointer and the code would attempt to resize
the Tx ring even if the Rx ring allocation had failed. This
would cause some confusion in the return code semantics. Fixed
up to just unwind the allocations if any of them fail and return
an error.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures fair beacon distribution in IBSS mode
by configuring proper CWmin based on slot time.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paprd needs to be done only on active chains(not for all the chains
that hw can support). The paprd training frames which are sent
for inactive chains would be hanging on the hw queue without
getting transmitted and would make the connection so unstable.
This issue happens only with the hw which supports paprd cal(ar9003).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "basic_rate" module option is not implemented correctly. If the
rate was set to zero it was supposed to set it to "basic_rate | 0x80".
Unfortunately the check to see if what zero was wrong and it checked
"!ai->config.rates" (which is always false) instead of
"!ai->config.rates[i]".
This option was just used for development and it wasn't documented
anywhere. Instead of fixing it, we can just remove it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
E1000 can benefit from calling the GRO receive functions.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers in general have an issue where timers fired
by mod_timer or work threads with schedule_work are running
outside of the rtnl_lock.
With no other lock protection these routines are vulnerable
to races with driver unload or reset paths.
The longer term solution to this might be a redesign with
safer locks being taken in the driver to guarantee no
reentrance, but for now a safe and effective fix is
to take the rtnl_lock in these routines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E1000 is using several timers that in a follow on patch
will need to acquire the rtnl_lock in order to be safe.
This patch moves the timer bodies into work queues which
will allow the next patch to add rtnl_lock.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel(r) DH89xxCC series. The new
device will be using Intel(r) i347-AT4 and Marvell(r) M88E1322 and
M88E1112 PHYs. Support for these devices has also been added here.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue in which we were setting all flag bits except
for promisc instead of clearing the promisc bits due to the incorrect use
of an |= instead of an &=.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
[1] commit e98cac447c
[2] commit 3f0c16e844
CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This board never went into production, but some engineering samples
are in use.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN4111T never reached production and is not being used for internal
or customer testing.
Since we have no production Falcon boards using the SFT9001 or the
GMAC, remove support for them as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_kfree_skb_any() helper to free the skb
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tmspci driver uses dev->name before register_netdev() and so prints tr%d
in initialization messages. Fix it by using dev_info.
Found and tested on real hardware.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/filter.c: In function ‘efx_probe_filters’:
drivers/net/sfc/filter.c:422: error: implicit declaration of function ‘vmalloc’
drivers/net/sfc/filter.c:422: warning: assignment makes pointer from integer without a cast
drivers/net/sfc/filter.c: In function ‘efx_remove_filters’:
drivers/net/sfc/filter.c:442: error: implicit declaration of function ‘vfree’
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, add it at the end.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut Schaa