* Unify calling of early_serial_txx9_setup.
* Use dedicated serial clock on RBTX4938.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Random cleanups spotted by checkpatch script.
* Do not initialize panic_timeout. "panic=" kernel parameter can be used.
* Do not add "ip=any" or "ip=bootp". This options is not board specific.
* Do not add "root=/dev/nfs". This is default on CONFIG_ROOT_NFS.
* Kill unused error checking.
* Fix IRQ comment to match current code.
* Kill some unneeded includes
* ST0_ERL is already cleared in generic code.
* conswitchp is initialized generic code.
* __init is not needed in prototype.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX4938 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX3927 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
when you take the address of the result. Noticed on a sparc64 compile
using a version 3.4.5 cross compiler.
kernel/time/tick-common.c: In function `tick_check_new_device':
kernel/time/tick-common.c:210: error: invalid lvalue in unary `&'
...
Just make it a regular expression.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
net: Make "networking" one-click deselectable.
ipv6: Fix useless proc net sockstat6 removal
tcp: MD5: Use MIB counter instead of warning for MD5 mismatch.
pkt_sched: Fix OOPS on ingress qdisc add.
niu: Fix error checking in niu_ethflow_to_class.
IPv6: datagram_send_ctl() should exit immediately when an error occured
mac80211: fix mesh beaconing
PS3: gelic: use unsigned long for irqflags
mac80211: fix cfg80211 hooks for master interface
nl80211: fix dump callbacks
mac80211: partially fix skb->cb use
rtl8187: Improve wireless statistics for RTL8187B
rtl8187: Fix for TX sequence number problem
mac80211: append CONFIG_ to MAC80211_VERBOSE_PS_DEBUG in net/mac80211/tx.c.
mac80211: fix sparse integer as NULL pointer warning
drivers/net/wireless/iwlwifi/iwl-led.c: printk fix
mac80211: return correct error return from ieee80211_wep_init
mac80211: tx, use dev_kfree_skb_any for beacon_get
rt2x00: Clear queue entry flags during initialization
rt2x00: Force full register config after start()
...
Replace the AMO_t typedef by a direct reference to 'struct amo'.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zap_vma_ptes() is intended to be used by drivers to unmap ptes assigned to the
driver private vmas. This interface is similar to zap_page_range() but is
less general & less likely to be abused.
Needed by the GRU driver.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file kernel.h contains the upper_32_bits macro. This patch adds the
other part, the lower_32_bits macro. Its first use will be in the driver
for AMD IOMMU.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a BlackBoard user to connector. BlackBoard is part of the TSP GPL
sampling framework (http://savannah.nongnu.org/p/tsp)
[akpm@linux-foundation.org: add comment]
Signed-off-by: Jerome Arbez-Gindre <jeromearbezgindre@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has no user now
Also print out info about adding/removing active regions.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar provided a fix to not call _PPC at processor driver
initialization time in "[PATCH] ACPI: fix cpufreq regression" (git
commit e4233dec74)
But it can still happen that _PPC is called at processor driver
initialization time.
This patch should make sure that this is not possible anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid one-off errors by introducing a resource_size() function.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current style for debug messages is to ensure they're always
parsed by the compiler and then subjected to dead code removal.
That way builds won't break only when debug options get enabled,
which is common when they are stripped out early by CPP.
This patch makes CONFIG_MTD_DEBUG adopt that convention.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current implementation of subpage read feature for NAND has issues with
small page devices. Small page NAND do not support RNDOUT command.
So subpage feature is not applicable for them.
This patch disables support of subpage for small page NAND.
The code is verified on nandsim(SP NAND simulation) and on LP NAND
devices.
Thanks a lot to Artem for finding this issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds a regulator driver for the TI bq24022 Single-Chip
Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This patch adds support for fixed regulators. This class of regulator is
not software controllable but can coexist on machines with software
controlable regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This interface is for machine specific code and allows the creation of
voltage/current domains (with constraints) for each regulator. It can
provide regulator constraints that will prevent device damage through
overvoltage or over current caused by buggy client drivers. It also
allows the creation of a regulator tree whereby some regulators are
supplied by others (similar to a clock tree).
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows regulator drivers to register their regulators and provide
operations to the core. It also has a notifier call chain for propagating
regulator events to clients.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support to allow consumer device drivers to control their regulator
power supply.
This uses a similar API to the kernel clock interface in that consumer
drivers can get and put a regulator (like they can with clocks atm) and
get/set voltage, current limit, mode, enable and disable. This should
allow consumers complete control over their supply voltage and current
limit. This also compiles out if not in use so drivers can be reused in
systems with no regulator based power control.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement lockless get_user_pages_fast for 64-bit powerpc.
Page table existence is guaranteed with RCU, and speculative page references
are used to take a reference to the pages without having a prior existence
guarantee on them.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorder fields in struct rfkill and add comments to make it clear
which fields are protected by rfkill->mutex.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dapm_reg_event() is used by devices using SND_SOC_DAPM_REG() so needs to
be exported to support building them as modules and prototyped to avoid
sparse warnings and potential build issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch cleans up the handling of the maple bus queue to remove
the risk of races when adding packets. It also removes references to the
redundant connect and disconnect functions.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This IOMMU helper function doesn't work for some architectures:
http://marc.info/?l=linux-kernel&m=121699304403202&w=2
It also breaks POWER and SPARC builds:
http://marc.info/?l=linux-kernel&m=121730388001890&w=2
Currently, only x86 IOMMUs use this so let's move it to x86 for
now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Synchronize changes to host virtual addresses which are part of
a KVM memory slot to the KVM shadow mmu. This allows pte operations
like swapping, page migration, and madvise() to transparently work
with KVM.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: accept pure device as a parent, not only platform_device
mfd: add platform_data to mfd_cell
mfd: Coding style fixes
mfd: Use to_platform_device instead of container_of
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
x86/PCI: use dev_printk when possible
PCI: add D3 power state avoidance quirk
PCI: fix bogus "'device' may be used uninitialized" warning in pci_slot
PCI: add an option to allow ASPM enabled forcibly
PCI: disable ASPM on pre-1.1 PCIe devices
PCI: disable ASPM per ACPI FADT setting
PCI MSI: Don't disable MSIs if the mask bit isn't supported
PCI: handle 64-bit resources better on 32-bit machines
PCI: rewrite PCI BAR reading code
PCI: document pci_target_state
PCI hotplug: fix typo in pcie hotplug output
x86 gart: replace to_pages macro with iommu_num_pages
x86, AMD IOMMU: replace to_pages macro with iommu_num_pages
iommu: add iommu_num_pages helper function
dma-coherent: add documentation to new interfaces
Cris: convert to using generic dma-coherent mem allocator
Sh: use generic per-device coherent dma allocator
ARM: support generic per-device coherent dma mem
Generic dma-coherent: fix DMA_MEMORY_EXCLUSIVE
x86: use generic per-device dma coherent allocator
...
When we read some part of a file through pagecache, if there is a
pagecache of corresponding index but this page is not uptodate, read IO
is issued and this page will be uptodate.
I think this is good for pagesize == blocksize environment but there is
room for improvement on pagesize != blocksize environment. Because in
this case a page can have multiple buffers and even if a page is not
uptodate, some buffers can be uptodate.
So I suggest that when all buffers which correspond to a part of a file
that we want to read are uptodate, use this pagecache and copy data from
this pagecache to user buffer even if a page is not uptodate. This can
reduce read IO and improve system throughput.
I wrote a benchmark program and got result number with this program.
This benchmark do:
1: mount and open a test file.
2: create a 512MB file.
3: close a file and umount.
4: mount and again open a test file.
5: pwrite randomly 300000 times on a test file. offset is aligned
by IO size(1024bytes).
6: measure time of preading randomly 100000 times on a test file.
The result was:
2.6.26
330 sec
2.6.26-patched
226 sec
Arch:i386
Filesystem:ext3
Blocksize:1024 bytes
Memory: 1GB
On ext3/4, a file is written through buffer/block. So random read/write
mixed workloads or random read after random write workloads are optimized
with this patch under pagesize != blocksize environment. This test result
showed this.
The benchmark program is as follows:
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <time.h>
#include <stdlib.h>
#include <string.h>
#include <sys/mount.h>
#define LEN 1024
#define LOOP 1024*512 /* 512MB */
main(void)
{
unsigned long i, offset, filesize;
int fd;
char buf[LEN];
time_t t1, t2;
if (mount("/dev/sda1", "/root/test1/", "ext3", 0, 0) < 0) {
perror("cannot mount\n");
exit(1);
}
memset(buf, 0, LEN);
fd = open("/root/test1/testfile", O_CREAT|O_RDWR|O_TRUNC);
if (fd < 0) {
perror("cannot open file\n");
exit(1);
}
for (i = 0; i < LOOP; i++)
write(fd, buf, LEN);
close(fd);
if (umount("/root/test1/") < 0) {
perror("cannot umount\n");
exit(1);
}
if (mount("/dev/sda1", "/root/test1/", "ext3", 0, 0) < 0) {
perror("cannot mount\n");
exit(1);
}
fd = open("/root/test1/testfile", O_RDWR);
if (fd < 0) {
perror("cannot open file\n");
exit(1);
}
filesize = LEN * LOOP;
for (i = 0; i < 300000; i++){
offset = (random() % filesize) & (~(LEN - 1));
pwrite(fd, buf, LEN, offset);
}
printf("start test\n");
time(&t1);
for (i = 0; i < 100000; i++){
offset = (random() % filesize) & (~(LEN - 1));
pread(fd, buf, LEN, offset);
}
time(&t2);
printf("%ld sec\n", t2-t1);
close(fd);
if (umount("/root/test1/") < 0) {
perror("cannot umount\n");
exit(1);
}
}
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.
The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.
[1] git commit 50f426b55d
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With KVM/GFP/XPMEM there isn't just the primary CPU MMU pointing to pages.
There are secondary MMUs (with secondary sptes and secondary tlbs) too.
sptes in the kvm case are shadow pagetables, but when I say spte in
mmu-notifier context, I mean "secondary pte". In GRU case there's no
actual secondary pte and there's only a secondary tlb because the GRU
secondary MMU has no knowledge about sptes and every secondary tlb miss
event in the MMU always generates a page fault that has to be resolved by
the CPU (this is not the case of KVM where the a secondary tlb miss will
walk sptes in hardware and it will refill the secondary tlb transparently
to software if the corresponding spte is present). The same way
zap_page_range has to invalidate the pte before freeing the page, the spte
(and secondary tlb) must also be invalidated before any page is freed and
reused.
Currently we take a page_count pin on every page mapped by sptes, but that
means the pages can't be swapped whenever they're mapped by any spte
because they're part of the guest working set. Furthermore a spte unmap
event can immediately lead to a page to be freed when the pin is released
(so requiring the same complex and relatively slow tlb_gather smp safe
logic we have in zap_page_range and that can be avoided completely if the
spte unmap event doesn't require an unpin of the page previously mapped in
the secondary MMU).
The mmu notifiers allow kvm/GRU/XPMEM to attach to the tsk->mm and know
when the VM is swapping or freeing or doing anything on the primary MMU so
that the secondary MMU code can drop sptes before the pages are freed,
avoiding all page pinning and allowing 100% reliable swapping of guest
physical address space. Furthermore it avoids the code that teardown the
mappings of the secondary MMU, to implement a logic like tlb_gather in
zap_page_range that would require many IPI to flush other cpu tlbs, for
each fixed number of spte unmapped.
To make an example: if what happens on the primary MMU is a protection
downgrade (from writeable to wrprotect) the secondary MMU mappings will be
invalidated, and the next secondary-mmu-page-fault will call
get_user_pages and trigger a do_wp_page through get_user_pages if it
called get_user_pages with write=1, and it'll re-establishing an updated
spte or secondary-tlb-mapping on the copied page. Or it will setup a
readonly spte or readonly tlb mapping if it's a guest-read, if it calls
get_user_pages with write=0. This is just an example.
This allows to map any page pointed by any pte (and in turn visible in the
primary CPU MMU), into a secondary MMU (be it a pure tlb like GRU, or an
full MMU with both sptes and secondary-tlb like the shadow-pagetable layer
with kvm), or a remote DMA in software like XPMEM (hence needing of
schedule in XPMEM code to send the invalidate to the remote node, while no
need to schedule in kvm/gru as it's an immediate event like invalidating
primary-mmu pte).
At least for KVM without this patch it's impossible to swap guests
reliably. And having this feature and removing the page pin allows
several other optimizations that simplify life considerably.
Dependencies:
1) mm_take_all_locks() to register the mmu notifier when the whole VM
isn't doing anything with "mm". This allows mmu notifier users to keep
track if the VM is in the middle of the invalidate_range_begin/end
critical section with an atomic counter incraese in range_begin and
decreased in range_end. No secondary MMU page fault is allowed to map
any spte or secondary tlb reference, while the VM is in the middle of
range_begin/end as any page returned by get_user_pages in that critical
section could later immediately be freed without any further
->invalidate_page notification (invalidate_range_begin/end works on
ranges and ->invalidate_page isn't called immediately before freeing
the page). To stop all page freeing and pagetable overwrites the
mmap_sem must be taken in write mode and all other anon_vma/i_mmap
locks must be taken too.
2) It'd be a waste to add branches in the VM if nobody could possibly
run KVM/GRU/XPMEM on the kernel, so mmu notifiers will only enabled if
CONFIG_KVM=m/y. In the current kernel kvm won't yet take advantage of
mmu notifiers, but this already allows to compile a KVM external module
against a kernel with mmu notifiers enabled and from the next pull from
kvm.git we'll start using them. And GRU/XPMEM will also be able to
continue the development by enabling KVM=m in their config, until they
submit all GRU/XPMEM GPLv2 code to the mainline kernel. Then they can
also enable MMU_NOTIFIERS in the same way KVM does it (even if KVM=n).
This guarantees nobody selects MMU_NOTIFIER=y if KVM and GRU and XPMEM
are all =n.
The mmu_notifier_register call can fail because mm_take_all_locks may be
interrupted by a signal and return -EINTR. Because mmu_notifier_reigster
is used when a driver startup, a failure can be gracefully handled. Here
an example of the change applied to kvm to register the mmu notifiers.
Usually when a driver startups other allocations are required anyway and
-ENOMEM failure paths exists already.
struct kvm *kvm_arch_create_vm(void)
{
struct kvm *kvm = kzalloc(sizeof(struct kvm), GFP_KERNEL);
+ int err;
if (!kvm)
return ERR_PTR(-ENOMEM);
INIT_LIST_HEAD(&kvm->arch.active_mmu_pages);
+ kvm->arch.mmu_notifier.ops = &kvm_mmu_notifier_ops;
+ err = mmu_notifier_register(&kvm->arch.mmu_notifier, current->mm);
+ if (err) {
+ kfree(kvm);
+ return ERR_PTR(err);
+ }
+
return kvm;
}
mmu_notifier_unregister returns void and it's reliable.
The patch also adds a few needed but missing includes that would prevent
kernel to compile after these changes on non-x86 archs (x86 didn't need
them by luck).
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix mm/filemap_xip.c build]
[akpm@linux-foundation.org: fix mm/mmu_notifier.c build]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm_take_all_locks holds off reclaim from an entire mm_struct. This allows
mmu notifiers to register into the mm at any time with the guarantee that
no mmu operation is in progress on the mm.
This operation locks against the VM for all pte/vma/mm related operations
that could ever happen on a certain mm. This includes vmtruncate,
try_to_unmap, and all page faults.
The caller must take the mmap_sem in write mode before calling
mm_take_all_locks(). The caller isn't allowed to release the mmap_sem
until mm_drop_all_locks() returns.
mmap_sem in write mode is required in order to block all operations that
could modify pagetables and free pages without need of altering the vma
layout (for example populate_range() with nonlinear vmas). It's also
needed in write mode to avoid new anon_vmas to be associated with existing
vmas.
A single task can't take more than one mm_take_all_locks() in a row or it
would deadlock.
mm_take_all_locks() and mm_drop_all_locks are expensive operations that
may have to take thousand of locks.
mm_take_all_locks() can fail if it's interrupted by signals.
When mmu_notifier_register returns, we must be sure that the driver is
notified if some task is in the middle of a vmtruncate for the 'mm' where
the mmu notifier was registered (mmu_notifier_invalidate_range_start/end
is run around the vmtruncation but mmu_notifier_register can run after
mmu_notifier_invalidate_range_start and before
mmu_notifier_invalidate_range_end). Same problem for rmap paths. And
we've to remove page pinning to avoid replicating the tlb_gather logic
inside KVM (and GRU doesn't work well with page pinning regardless of
needing tlb_gather), so without mm_take_all_locks when vmtruncate frees
the page, kvm would have no way to notice that it mapped into sptes a page
that is going into the freelist without a chance of any further
mmu_notifier notification.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding platform_data to mfd_cell allows passing of platform data directly
to the platform_device created for each cell and thus reuse of existing
drivers.
On the other side it can be used as a hook to mfd_cell itself
removing the need in mfd_get_cell method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Libata has some hacks to deal with certain controllers going silly in D3
state. The right way to handle this is to keep a PCI device flag for
such devices. That can then be generalised for no ATA devices with power
problems.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ACPI FADT table includes an ASPM control bit. If the bit is set, do
not enable ASPM since it may indicate that the platform doesn't actually
support the feature.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As noted by Adrian:
Commit 3ab8352137 (kexec jump)
causes the following build error on sh:
<-- snip -->
...
CC kernel/kexec.o
{standard input}: Assembler messages:
{standard input}:1518: Error: offset to unaligned destination
make[2]: *** [kernel/kexec.o] Error 1
<-- snip -->
If I understand the assembler correctly it fails at
include/asm-sh/kexec.h:59
The issue here is that the mova reference lacks an explicit alignment,
and previous code paths would end up with this on a 16-bit boundary,
so we make the alignment explicit.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up and optimize cpumask_of_cpu(), by sharing all the zero words.
Instead of stupidly generating all possible i=0...NR_CPUS 2^i patterns
creating a huge array of constant bitmasks, realize that the zero words
can be shared.
In other words, on a 64-bit architecture, we only ever need 64 of these
arrays - with a different bit set in one single world (with enough zero
words around it so that we can create any bitmask by just offsetting in
that big array). And then we just put enough zeroes around it that we
can point every single cpumask to be one of those things.
So when we have 4k CPU's, instead of having 4k arrays (of 4k bits each,
with one bit set in each array - 2MB memory total), we have exactly 64
arrays instead, each 8k bits in size (64kB total).
And then we just point cpumask(n) to the right position (which we can
calculate dynamically). Once we have the right arrays, getting
"cpumask(n)" ends up being:
static inline const cpumask_t *get_cpu_mask(unsigned int cpu)
{
const unsigned long *p = cpu_bit_bitmap[1 + cpu % BITS_PER_LONG];
p -= cpu / BITS_PER_LONG;
return (const cpumask_t *)p;
}
This brings other advantages and simplifications as well:
- we are not wasting memory that is just filled with a single bit in
various different places
- we don't need all those games to re-create the arrays in some dense
format, because they're already going to be dense enough.
if we compile a kernel for up to 4k CPU's, "wasting" that 64kB of memory
is a non-issue (especially since by doing this "overlapping" trick we
probably get better cache behaviour anyway).
[ mingo@elte.hu:
Converted Linus's mails into a commit. See:
http://lkml.org/lkml/2008/7/27/156http://lkml.org/lkml/2008/7/28/320
Also applied a family filter - which also has the side-effect of leaving
out the bits where Linus calls me an idio... Oh, never mind ;-)
]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc: Disable 64K hugetlb support when doing 64K SPU mappings
powerpc/powermac: Fixup default serial port device for pmac_zilog
powerpc/powermac: Use sane default baudrate for SCC debugging
powerpc/mm: Implement _PAGE_SPECIAL & pte_special() for 64-bit
powerpc: Show processor cache information in sysfs
powerpc: Make core id information available to userspace
powerpc: Make core sibling information available to userspace
powerpc/vio: More fallout from dma_mapping_error API change
ibmveth: Fix multiple errors with dma_mapping_error conversion
powerpc/pseries: Fix CMO sysdev attribute API change fallout
powerpc: Enable tracehook for the architecture
powerpc: Add TIF_NOTIFY_RESUME support for tracehook
powerpc: Add asm/syscall.h with the tracehook entry points
powerpc: Make syscall tracing use tracehook.h helpers
powerpc: Call tracehook_signal_handler() when setting up signal frames
powerpc: Update cpu_sibling_maps dynamically
powerpc: register_cpu_online should be __cpuinit
powerpc: kill useless SMT code in prom_hold_cpus
powerpc: Fix 8xx build failure
powerpc: Fix vio build warnings
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (72 commits)
sh: SuperH Mobile CEU and camera platform data for AP325RXA
sh: Update smc911x platform data for AP325RXA
sh: SuperH Mobile LCDC platform data for AP325RXA
sh: Add SuperH Mobile CEU platform data for Migo-R
sh: Add SuperH Mobile LCDC platform data for Migo-R
sh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.
sh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.
sh: Wire up new syscalls.
sh: fix uImage Entry Point
sh_keysc: remove request_mem_region() and release_mem_region()
sh: Don't miss pending signals returning to user mode after signal processing
sh: Use clk_always_enable() on sh7366
sh: Use clk_always_enable() on sh7343 / SE77343
sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
sh: Use clk_always_enable() on sh7723 / ap325rxa
sh: Introduce clk_always_enable() function
sh: Show all clocks and their state in /proc/clocks
sh: Merge sh7343 and sh7722 clock code
sh: Add SuperH Mobile MSTPCR bits to clock framework
sh: Use arch_flags to simplify sh7722 siu clock code
...
The CPM2 BRG setup functions cpm_setbrg and cpm2_fastbrg don't support
external clocks. This patch adds a new exported __cpm2_setbrg function
that takes the clock rate and clock source as extra parameters, and moves
cpm_setbrg and cpm2_fastbrg to include/asm-powerpc/cpm2.h where they
become inline wrappers around __cpm2_setbrg.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.
Based on earlier work by Laurent Pinchart.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.
Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SuperH specific funcion clk_always_enable(), useful to enable MSTPCR
bits in processor or board specific code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add arch_flags to struct clk so we can keep per-clock private data
somewhere and share code between multiple clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
updated the following codes for Solution Endine 7343:
- fix compile error in arch/sh/boards/se/7343/irq.c
- add nor flash physmaps
- update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support SH-Ether for Hitachi Solution Engine.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The connect and disconnect functions are unnecessary - everything they do can be
accomplished in the initial probe - so remove them.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates everything but the bare assembly routines, which we
will sync up in a follow-up patch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
16kB is a useful size on nommu, while 64kB still tends to be too big to
be useful. Newer MMUs are likely to support this as well, so plug it
in in anticipation of those, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves get_fs/set_fs() and friends in to asm/segment.h. The
mm_segment_t definition is likewise consolidated from the _32/_64 split.
This is prepatory groundwork for using the generic address space limit
and verification routines across mmu/nommu configs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Atsushi Nemoto