Remove a leftover from the code that transferred a couple of TIF bits
from the previous task to the next task.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a tricky interaction between the machine check handler
and the critical sections of load_fpu_regs and save_fpu_regs
functions. If the machine check interrupts one of the two
functions the critical section cleanup will complete the function
before the machine check handler s390_do_machine_check is called.
Trouble is that the machine check handler needs to validate the
floating point registers *before* and not *after* the completion
of load_fpu_regs/save_fpu_regs.
The simplest solution is to rewind the PSW to the start of the
load_fpu_regs/save_fpu_regs and retry the function after the
return from the machine check handler.
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit e22cf8ca6f ("s390/cpumf: rework program parameter setting
to detect guest samples") requires guest changes to get proper
guest/host. We can do better: We can use the primary asn value,
which is set on all Linux variants to compare this with the host
pp value.
We now have the following cases:
1. Guest using PP
host sample: gpp == 0, asn == hpp --> host
guest sample: gpp != 0 --> guest
2. Guest not using PP
host sample: gpp == 0, asn == hpp --> host
guest sample: gpp == 0, asn != hpp --> guest
As soon as the host no longer sets CR4, we must back out
this heuristics - let's add a comment in switch_to.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It does not make sense to try to relinquish the time slice with diag 0x9c
to a CPU in a state that does not allow to schedule the CPU. The scenario
where this can happen is a CPU waiting in udelay/mdelay while holding a
spin-lock.
Add a CIF bit to tag a CPU in enabled wait and use it to detect that the
yield of a CPU will not be successful and skip the diagnose call.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When using systemtap it was observed that our udelay implementation is
rather suboptimal if being called from a kprobe handler installed by
systemtap.
The problem observed when a kprobe was installed on lock_acquired().
When the probe was hit the kprobe handler did call udelay, which set
up an (internal) timer and reenabled interrupts (only the clock comparator
interrupt) and waited for the interrupt.
This is an optimization to avoid that the cpu is busy looping while waiting
that enough time passes. The problem is that the interrupt handler still
does call irq_enter()/irq_exit() which then again can lead to a deadlock,
since some accounting functions may take locks as well.
If one of these locks is the same, which caused lock_acquired() to be
called, we have a nice deadlock.
This patch reworks the udelay code for the interrupts disabled case to
immediately leave the low level interrupt handler when the clock
comparator interrupt happens. That way no C code is being called and the
deadlock cannot happen anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The program parameter can be used to mark hardware samples with
some token. Previously, it was used to mark guest samples only.
Improve the program parameter doubleword by combining two parts,
the leftmost LPP part and the rightmost PID part. Set the PID
part for processes by using the task PID.
To distinguish host and guest samples for the kernel (PID part
is zero), the guest must always set the program paramater to a
non-zero value. Use the leftmost bit in the LPP part of the
program parameter to be able to detect guest kernel samples.
[brueckner@linux.vnet.ibm.com]: Split __LC_CURRENT and introduced
__LC_LPP. Corrected __LC_CURRENT users and adjusted assembler parts.
And updated the commit message accordingly.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Various functions in entry.S perform test-under-mask instructions
to test for particular bits in memory. Because test-under-mask uses
a mask value of one byte, the mask value and the offset into the
memory must be calculated manually. This easily introduces errors
and is hard to review and read.
Introduce the TSTMSK assembler macro to specify a mask constant and
let the macro calculate the offset and the byte mask to generate a
test-under-mask instruction. The benefit is that existing symbolic
constants can now be used for tests. Also the macro checks for
zero mask values and mask values that consist of multiple bytes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previously, the init task did not have an allocated FPU save area and
saving an FPU state was not possible. Now if the vector extension is
always enabled, provide a static FPU save area to save FPU states of
vector instructions that can be executed quite early.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the kernel detects that the s390 hardware supports the vector
facility, it is enabled by default at an early stage. To force
it off, use the novx kernel parameter. Note that there is a small
time window, where the vector facility is enabled before it is
forced to be off.
With enabling the vector facility by default, the FPU save and
restore functions can be improved. They do not longer require
to manage expensive control register updates to enable or disable
the vector enablement control for particular processes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The calculation for the SMT scaling factor for a hardware thread
which has been partially idle needs to disregard the cycles spent
by the other threads of the core while the thread is idle.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The critical section cleanup code misses to add the offset of the
thread_struct to the task address.
Therefore, if the critical section code gets executed, it may corrupt
the task struct or restore the contents of the floating point registers
from the wrong memory location.
Fixes d0164ee20d "s390/kernel: remove save_fpu_regs() parameter and use
__LC_CURRENT instead".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Right now we use the address of the sie control block as tag for
the sampling data. This is hard to get for users. Let's just use
the PID of the cpu thread to mark the hardware samples.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All calls to save_fpu_regs() specify the fpu structure of the current task
pointer as parameter. The task pointer of the current task can also be
retrieved from the CPU lowcore directly. Remove the parameter definition,
load the __LC_CURRENT task pointer from the CPU lowcore, and rebase the FPU
structure onto the task structure. Apply the same approach for the
load_fpu_regs() function.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a machine checks is received while the CPU is in the kernel, only
the s390_do_machine_check function will be called. The call to
s390_handle_mcck is postponed until the CPU returns to user space.
Because of this it is safe to use the asynchronous stack for machine
checks even if the CPU is already handling an interrupt.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reorder the instructions of UPDATE_VTIME to improve superscalar execution,
remove duplicate checks for problem-state from the asynchronous interrupt
handlers, and move the check for problem-state from the synchronous
exit path to the program check path as it is only needed for program
checks inside the kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently there are two mechanisms to deal with cleanup work due to
interrupts. The HANDLE_SIE_INTERCEPT macro is used to undo the changes
required to enter SIE in sie64a. If the SIE instruction causes a program
check, or an asynchronous interrupt is received the HANDLE_SIE_INTERCEPT
code forwards the program execution to sie_exit.
All the other critical sections in entry.S are handled by the code in
cleanup_critical that is called by the SWITCH_ASYNC macro.
Move the sie64a function to the beginning of the critical section and
add the code from HANDLE_SIE_INTERCEPT to cleanup_critical. Add a special
case for the sie64a cleanup to the program check handler.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The HANDLE_SIE_INTERCEPT macro is used in the interrupt handlers
and the program check handler to undo a few changes done by sie64a.
Among them are guest vs host LPP, the gmap ASCE vs kernel ASCE and
the bit that indicates that SIE is currently running on the CPU.
There is a race of a voluntary SIE exit vs asynchronous interrupts.
If the CPU completed the SIE instruction and the TM instruction of
the LPP macro at the time it receives an interrupt, the interrupt
handler will run while the LPP, the ASCE and the SIE bit are still
set up for guest execution. This might result in wrong sampling data,
but it will not cause data corruption or lockups.
The critical section in sie64a needs to be enlarged to include all
instructions that undo the changes required for guest execution.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve the save and restore behavior of FPU register contents to use the
vector extension within the kernel.
The kernel does not use floating-point or vector registers and, therefore,
saving and restoring the FPU register contents are performed for handling
signals or switching processes only. To prepare for using vector
instructions and vector registers within the kernel, enhance the save
behavior and implement a lazy restore at return to user space from a
system call or interrupt.
To implement the lazy restore, the save_fpu_regs() sets a CPU information
flag, CIF_FPU, to indicate that the FPU registers must be restored.
Saving and setting CIF_FPU is performed in an atomic fashion to be
interrupt-safe. When the kernel wants to use the vector extension or
wants to change the FPU register state for a task during signal handling,
the save_fpu_regs() must be called first. The CIF_FPU flag is also set at
process switch. At return to user space, the FPU state is restored. In
particular, the FPU state includes the floating-point or vector register
contents, as well as, vector-enablement and floating-point control. The
FPU state restore and clearing CIF_FPU is also performed in an atomic
fashion.
For KVM, the restore of the FPU register state is performed when restoring
the general-purpose guest registers before the SIE instructions is started.
Because the path towards the SIE instruction is interruptible, the CIF_FPU
flag must be checked again right before going into SIE. If set, the guest
registers must be reloaded again by re-entering the outer SIE loop. This
is the same behavior as if the SIE critical section is interrupted.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit 0c8c0f03e3
"x86/fpu, sched: Dynamically allocate 'struct fpu'"
moved the thread_struct to the end of the task_struct.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
exit_sie_sync is used to kick CPUs out of SIE and prevent reentering at
any point in time. This is used to reload the prefix pages and to
set the IBS stuff in a way that guarantees that after this function
returns we are no longer in SIE. All current users trigger KVM requests.
The request must be set before we block the CPUs to avoid races. Let's
make this implicit by adding the request into a new function
kvm_s390_sync_requests that replaces exit_sie_sync and split out
s390_vcpu_block and s390_vcpu_unblock, that can be used to keep
CPUs out of SIE independent of requests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Remove the 31 bit syscalls from the syscall table. This is a separate patch
just in case I screwed something up so it can be easily reverted.
However the conversion was done with a script, so everything should be ok.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename a couple of files to get rid of the "64" suffix.
"git blame" will still work.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e58 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To improve the output of the perf tool hide most of the symbols
from entry[64].S by using the '.L' prefix.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration,
GDB support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace interface
and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still,
we have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j5Od
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm into next
Pull KVM updates from Paolo Bonzini:
"At over 200 commits, covering almost all supported architectures, this
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration, GDB
support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by
Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace
interface and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still, we
have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (203 commits)
KVM: add missing cleanup_srcu_struct
KVM: PPC: Book3S PR: Rework SLB switching code
KVM: PPC: Book3S PR: Use SLB entry 0
KVM: PPC: Book3S HV: Fix machine check delivery to guest
KVM: PPC: Book3S HV: Work around POWER8 performance monitor bugs
KVM: PPC: Book3S HV: Make sure we don't miss dirty pages
KVM: PPC: Book3S HV: Fix dirty map for hugepages
KVM: PPC: Book3S HV: Put huge-page HPTEs in rmap chain for base address
KVM: PPC: Book3S HV: Fix check for running inside guest in global_invalidates()
KVM: PPC: Book3S: Move KVM_REG_PPC_WORT to an unused register number
KVM: PPC: Book3S: Add ONE_REG register names that were missed
KVM: PPC: Add CAP to indicate hcall fixes
KVM: PPC: MPIC: Reset IRQ source private members
KVM: PPC: Graciously fail broken LE hypercalls
PPC: ePAPR: Fix hypercall on LE guest
KVM: PPC: BOOK3S: Remove open coded make_dsisr in alignment handler
KVM: PPC: BOOK3S: Always use the saved DAR value
PPC: KVM: Make NX bit available with magic page
KVM: PPC: Disable NX for old magic page using guests
KVM: PPC: BOOK3S: HV: Add mixed page-size support for guest
...
The oi and ni instructions used in entry[64].S to set and clear bits
in the thread-flags are not guaranteed to be atomic in regard to other
CPUs. Split the TIF bits into CPU, pt_regs and thread-info specific
bits. Updates on the TIF bits are done with atomic instructions,
updates on CPU and pt_regs bits are done with non-atomic instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Always switch to the kernel ASCE in switch_mm. Load the secondary
space ASCE in finish_arch_post_lock_switch after checking that
any pending page table operations have completed. The primary
ASCE is loaded in entry[64].S. With this the update_primary_asce
call can be removed from the switch_to macro and from the start
of switch_mm function. Remove the load_primary argument from
update_user_asce/clear_user_asce, rename update_user_asce to
set_user_asce and rename update_primary_asce to load_kernel_asce.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
per_perc_atmid is currently a two-byte field that combines two
fields, the PER code and the PER Addressing-and-Translation-Mode
Identification (ATMID)
Let's make them accessible indepently and also rename per_cause to
per_code.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The current uaccess code uses a page table walk in some circumstances,
e.g. in case of the in atomic futex operations or if running on old
hardware which doesn't support the mvcos instruction.
However it turned out that the page table walk code does not correctly
lock page tables when accessing page table entries.
In other words: a different cpu may invalidate a page table entry while
the current cpu inspects the pte. This may lead to random data corruption.
Adding correct locking however isn't trivial for all uaccess operations.
Especially copy_in_user() is problematic since that requires to hold at
least two locks, but must be protected against ABBA deadlock when a
different cpu also performs a copy_in_user() operation.
So the solution is a different approach where we change address spaces:
User space runs in primary address mode, or access register mode within
vdso code, like it currently already does.
The kernel usually also runs in home space mode, however when accessing
user space the kernel switches to primary or secondary address mode if
the mvcos instruction is not available or if a compare-and-swap (futex)
instruction on a user space address is performed.
KVM however is special, since that requires the kernel to run in home
address space while implicitly accessing user space with the sie
instruction.
So we end up with:
User space:
- runs in primary or access register mode
- cr1 contains the user asce
- cr7 contains the user asce
- cr13 contains the kernel asce
Kernel space:
- runs in home space mode
- cr1 contains the user or kernel asce
-> the kernel asce is loaded when a uaccess requires primary or
secondary address mode
- cr7 contains the user or kernel asce, (changed with set_fs())
- cr13 contains the kernel asce
In case of uaccess the kernel changes to:
- primary space mode in case of a uaccess (copy_to_user) and uses
e.g. the mvcp instruction to access user space. However the kernel
will stay in home space mode if the mvcos instruction is available
- secondary space mode in case of futex atomic operations, so that the
instructions come from primary address space and data from secondary
space
In case of kvm the kernel runs in home space mode, but cr1 gets switched
to contain the gmap asce before the sie instruction gets executed. When
the sie instruction is finished cr1 will be switched back to contain the
user asce.
A context switch between two processes will always load the kernel asce
for the next process in cr1. So the first exit to user space is a bit
more expensive (one extra load control register instruction) than before,
however keeps the code rather simple.
In sum this means there is no need to perform any error prone page table
walks anymore when accessing user space.
The patch seems to be rather large, however it mainly removes the
the page table walk code and restores the previously deleted "standard"
uaccess code, with a couple of changes.
The uaccess without mvcos mode can be enforced with the "uaccess_primary"
kernel parameter.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit 050eef364a "[S390] fix tlb flushing vs. concurrent
/proc accesses" introduced the attach counter to avoid using the
mm_users value to decide between IPTE for every PTE and lazy TLB
flushing with IDTE. That fixed the problem with mm_users but it
introduced another subtle race, fortunately one that is very hard
to hit.
The background is the requirement of the architecture that a valid
PTE may not be changed while it can be used concurrently by another
cpu. The decision between IPTE and lazy TLB flushing needs to be
done while the PTE is still valid. Now if the virtual cpu is
temporarily stopped after the decision to use lazy TLB flushing but
before the invalid bit of the PTE has been set, another cpu can attach
the mm, find that flush_mm is set, do the IDTE, return to userspace,
and recreate a TLB that uses the PTE in question. When the first,
stopped cpu continues it will change the PTE while it is attached on
another cpu. The first cpu will do another IDTE shortly after the
modification of the PTE which makes the race window quite short.
To fix this race the CPU that wants to attach the address space of a
user space thread needs to wait for the end of the PTE modification.
The number of concurrent TLB flushers for an mm is tracked in the
upper 16 bits of the attach_count and finish_arch_post_lock_switch
is used to wait for the end of the flush operation if required.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit 616498813b "s390: system call path micro optimization"
introduced a regression in regard to system call restarting and inferior
function calls via the ptrace interface. The pointer to the system call
table needs to be loaded in sysc_sigpending if do_signal returns with
TIF_SYSCALl set after it restored a system call context.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Modify the psw_idle waiting logic in entry[64].S to return with
interrupts disabled. This avoids potential issues with udelay
and interrupt loops as interrupts are not reenabled after
clock comparator interrupts.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the introduction of PCI it became apparent that s390 should
convert to generic hardirqs as too many drivers do not have the
correct dependency for GENERIC_HARDIRQS. On the architecture
level s390 does not have irq lines. It has external interrupts,
I/O interrupts and adapter interrupts. This patch hard-codes all
external interrupts as irq #1, all I/O interrupts as irq #2 and
all adapter interrupts as irq #3. The additional information from
the lowcore associated with the interrupt is stored in the
pt_regs of the interrupt frame, where the interrupt handler can
pick it up. For PCI/MSI interrupts the adapter interrupt handler
scans the relevant bit fields and calls generic_handle_irq with
the virtual irq number for the MSI interrupt.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copy the interrupt parameters from the lowcore to the pt_regs structure
in entry[64].S and reduce the arguments of the low level interrupt handler
to the pt_regs pointer only. In addition move the test-pending-interrupt
loop from do_IRQ to entry[64].S to make sure that interrupt information
is always delivered via pt_regs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a pointer to the system call table to the thread_info structure.
The TIF_31BIT bit is set or cleared by SET_PERSONALITY exactly once
for the lifetime of a process. With the pointer to the correct system
call table in thread_info the system call code in entry64.S path can
drop the check for TIF_31BIT which saves a couple of instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Store the stack pointers in the lowcore for the kernel stack, the async
stack and the panic stack with the offset required for the first user.
This avoids an unnecessary add instruction on the system call path.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current machine check code uses the registers stored by the machine
in the lowcore at __LC_GPREGS_SAVE_AREA as the registers of the interrupted
context. The registers 0-7 of a user process can get clobbered if a machine
checks interrupts the execution of a critical section in entry[64].S.
The reason is that the critical section cleanup code may need to modify
the PSW and the registers for the previous context to get to the end of a
critical section. If registers 0-7 have to be replaced the relevant copy
will be in the registers, which invalidates the copy in the lowcore. The
machine check handler needs to explicitly store registers 0-7 to the stack.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 update from Martin Schwidefsky:
"Add support to generate code for the latest machine zEC12, MOD and XOR
instruction support for the BPF jit compiler, the dasd safe offline
feature and the big one: the s390 architecture gets PCI support!!
Right before the world ends on the 21st ;-)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390/qdio: rename the misleading PCI flag of qdio devices
s390/pci: remove obsolete email addresses
s390/pci: speed up __iowrite64_copy by using pci store block insn
s390/pci: enable NEED_DMA_MAP_STATE
s390/pci: no msleep in potential IRQ context
s390/pci: fix potential NULL pointer dereference in dma_free_seg_table()
s390/pci: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
s390/bpf,jit: add support for XOR instruction
s390/bpf,jit: add support MOD instruction
s390/cio: fix pgid reserved check
vga: compile fix, disable vga for s390
s390/pci: add PCI Kconfig options
s390/pci: s390 specific PCI sysfs attributes
s390/pci: PCI hotplug support via SCLP
s390/pci: CHSC PCI support for error and availability events
s390/pci: DMA support
s390/pci: PCI adapter interrupts for MSI/MSI-X
s390/bitops: find leftmost bit instruction support
s390/pci: CLP interface
s390/pci: base support
...
The current single step code is racy in regard to concurrent delivery
of signals. If a signal is delivered after a PER program check occurred
but before the TIF_PER_TRAP bit has been checked in entry[64].S the code
clears TIF_PER_TRAP and then calls do_signal. This is wrong, if the
instruction completed (or has been suppressed) a SIGTRAP should be
delivered to the debugger in any case. Only if the instruction has been
nullified the SIGTRAP may not be send.
The new logic always sets TIF_PER_TRAP if the program check indicates PER
tracing but removes it again for all program checks that are nullifying.
The effect is that for each change in the PSW address we now get a
single SIGTRAP.
Reported-by: Andreas Arnez <arnez@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current virtual timer interface is inherently per-cpu and hard to
use. The sole user of the interface is appldata which uses it to execute
a function after a specific amount of cputime has been used over all cpus.
Rework the virtual timer interface to hook into the cputime accounting.
This makes the interface independent from the CPU timer interrupts, and
makes the virtual timers global as opposed to per-cpu.
Overall the code is greatly simplified. The downside is that the accuracy
is not as good as the original implementation, but it is still good enough
for appldata.
Reviewed-by: Jan Glauber <jang@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Setting the cpu restart parameters is done in three different fashions:
- directly setting the four parameters individually
- copying the four parameters with memcpy (using 4 * sizeof(long))
- copying the four parameters using a private structure
In addition code in entry*.S relies on a certain order of the restart
members of struct _lowcore.
Make all of this more robust to future changes by adding a
mem_absolute_assign(dest, val) define, which assigns val to dest
using absolute addressing mode. Also the load multiple instructions
in entry*.S have been split into separate load instruction so the
order of the struct _lowcore members doesn't matter anymore.
In addition move the prototypes of memcpy_real/absolute from uaccess.h
to processor.h. These memcpy* variants are not related to uaccess at all.
string.h doesn't seem to match as well, so lets use processor.h.
Also replace the eight byte array in struct _lowcore which represents a
misaliged u64 with a u64. The compiler will always create code that
handles the misaligned u64 correctly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use sigp order code defines in assembly code as well.
With this change all places that use sigp constants should
have been converted to use self describing defines instead
of directly using constants.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a small race window in the __switch_to code in regard to
the transfer of the TIF_MCCK_PENDING bit from the previous to the
next task. The bit is transferred before the task struct pointer
and the thread-info pointer for the next task has been stored to
lowcore. If a machine check sets the TIF_MCCK_PENDING bit between
the transfer code and the store of current/thread_info the bit
is still set for the previous task. And if the previous task has
terminated it can get lost. The effect is that a pending CRW is
not retrieved until the next machine checks sets TIF_MCCK_PENDING.
To fix this reorder __switch_to to first store the task struct
and thread-info pointer and then do the transfer of the bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whenever the cpu loads an enabled wait PSW it will appear as idle to the
underlying host system. The code in default_idle calls vtime_stop_cpu
which does the necessary voodoo to get the cpu time accounting right.
The udelay code just loads an enabled wait PSW. To correct this rework
the vtime_stop_cpu/vtime_start_cpu logic and move the difficult parts
to entry[64].S, vtime_stop_cpu can now be called from anywhere and
vtime_start_cpu is gone. The correction of the cpu time during wakeup
from an enabled wait PSW is done with a critical section in entry[64].S.
As vtime_start_cpu is gone, s390_idle_check can be removed as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 16 bit value at the lowcore location with offset 0x84 is the
cpu address that is associated with an external interrupt. Rename
the field from cpu_addr to ext_cpu_addr to make that clear.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the program interruption code and the translation exception identifier
to the pt_regs structure as 'int_code' and 'int_parm_long' and make the
first level interrupt handler in entry[64].S store the two values. That
makes it possible to drop 'prot_addr' and 'trap_no' from the thread_struct
and to reduce the number of arguments to a lot of functions. Finally
un-inline do_trap. Overall this saves 5812 bytes in the .text section of
the 64 bit kernel.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Another round of cleanup for entry[64].S, in particular the program check
handler looks more reasonable now. The code size for the 31 bit kernel
has been reduced by 616 byte and by 528 byte for the 64 bit version.
Even better the code is a bit faster as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an explicit TIF_SYSCALL bit that indicates if a task is inside
a system call. The svc_code in the pt_regs structure is now only
valid if TIF_SYSCALL is set. With this definition TIF_RESTART_SVC
can be replaced with TIF_SYSCALL. Overall do_signal is a bit more
readable and it saves a few lines of code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a ERESTARTNOHAND/ERESTARTSYS/ERESTARTNOINTR restarting system call
do_signal will prepare the restart of the system call with a rewind of
the PSW before calling get_signal_to_deliver (where the debugger might
take control). For A ERESTART_RESTARTBLOCK restarting system call
do_signal will set -EINTR as return code.
There are two issues with this approach:
1) strace never sees ERESTARTNOHAND, ERESTARTSYS, ERESTARTNOINTR or
ERESTART_RESTARTBLOCK as the rewinding already took place or the
return code has been changed to -EINTR
2) if get_signal_to_deliver does not return with a signal to deliver
the restart via the repeat of the svc instruction is left in place.
This opens a race if another signal is made pending before the
system call instruction can be reexecuted. The original system call
will be restarted even if the second signal would have ended the
system call with -EINTR.
These two issues can be solved by dropping the early rewind of the
system call before get_signal_to_deliver has been called and by using
the TIF_RESTART_SVC magic to do the restart if no signal has to be
delivered. The only situation where the system call restart via the
repeat of the svc instruction is appropriate is when a SA_RESTART
signal is delivered to user space.
Unfortunately this breaks inferior calls by the debugger again. The
system call number and the length of the system call instruction is
lost over the inferior call and user space will see ERESTARTNOHAND/
ERESTARTSYS/ERESTARTNOINTR/ERESTART_RESTARTBLOCK. To correct this a
new ptrace interface is added to save/restore the system call number
and system call instruction length.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the save_area_64 field from the 0xe00 - 0xf00 area in the lowcore.
Use a free slot in the save_area array instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch a new S390 shutdown trigger "restart" is added. If under
z/VM "systerm restart" is entered or under the HMC the "PSW restart" button
is pressed, the PSW located at 0 (31 bit) or 0x1a0 (64 bit) bit is loaded.
Now we execute do_restart() that processes the restart action that is
defined under /sys/firmware/shutdown_actions/on_restart. Currently the
following actions are possible: reipl (default), stop, vmcmd, dump, and
dump_reipl.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.
Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On cpu hot remove a PFAULT CANCEL command is sent to the hypervisor
which in turn will cancel all outstanding pfault requests that have
been issued on that cpu (the same happens with a SIGP cpu reset).
The result is that we end up with uninterruptible processes where
the interrupt that would wake up these processes never arrives.
In order to solve this all processes which wait for a pfault
completion interrupt get woken up after a cpu hot remove. The worst
case that could happen is that they fault again and in turn need to
wait again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When starting a new CPU we currently jump to start_secondary() without
setting register 14 (the return address) correctly. Therefore on the stack
frame for start_secondary an invalid return address is stored. This leads
to wrong stack back traces in kernel dumps.
Example:
#00 [1f33fe48] cpu_idle at 10614a
#01 [1f33fe90] start_secondary at 54fa88
#02 [1f33feb8] (null) at 0 <--- invalid
To fix this start_secondary() is called now with basr/brasl that sets
register 14 correctly. The output of the stack backtrace looks then
like the following:
#00 [1f33fe48] cpu_idle at 10614a
#01 [1f33fe90] start_secondary at 54fa88
#02 [1f33feb8] restart_base at 54f41e <--- correct
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the code in the 31 bit entry.S code as similar as possible to the
64 bit version in entry64.S. That makes it easier to add new code to
the first level interrupt handler that affects both 31 and 64 bit kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add kprobes annotations to get the massive 'probe kernel.function("*") {}'
stress test working.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix kprobes after git commit 1e54622e04
broke it. The kprobe_handler is now called with interrupts in the state
at the time of the breakpoint. The single step of the replaced instruction
is done with interrupts off which makes it necessary to enable and disable
the interupts in the kprobes code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do the setup of the stack overflow argument for the sixth system
call parameter right before the branch to the system call function.
That simplifies the system call parameter access code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read external interrupts parameters from the lowcore in the first
level interrupt handler in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read all required fields for program checks from the lowcore in the
first level interrupt handler in entry[64].S. If the context that
caused the fault was enabled for interrupts we can now re-enable the
irqs in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.
Fix this by doing all the work within the correct context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copy the last breaking event address from the lowcore to a new
field in the thread_struct on each system entry. Add a new
ptrace request PTRACE_GET_LAST_BREAK and a new utrace regset
REGSET_LAST_BREAK to query the last breaking event.
This is useful for debugging wild branches in user space code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A machine check can interrupt the i/o and external interrupt handler
anytime. If the machine check occurs while the interrupt handler is
waking up from idle vtime_start_cpu can get executed a second time
and the int_clock / async_enter_timer values in the lowcore get
clobbered. This can confuse the cpu time accounting.
To fix this problem two changes are needed. First the machine check
handler has to use its own copies of int_clock and async_enter_timer,
named mcck_clock and mcck_enter_timer. Second the nested execution
of vtime_start_cpu has to be prevented. This is done in s390_idle_check
by checking the wait bit in the program status word.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The system call path in entry[64].S is run with interrupts enabled.
Remove the irq tracing check from the system call exit code. If a
program check interrupted a context enabled for interrupts do a
call to trace_irq_off_caller in the program check handler before
branching to the system call exit code.
Restructure the system call and io interrupt return code to avoid
avoid the lpsw[e] to disable machine checks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup the #ifdef mess at io_work in entry[64].S and streamline the
TIF work code of the system call and io exit path.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a machine check interrupts the io interrupt handler on one of the
instructions between io_return and io_leave the critical section
cleanup code will move the return psw to io_work_loop. By doing that
the switch from the asynchronous interrupt stack to the process stack
is skipped. If e.g. TIF_NEED_RESCHED is set things break because
the scheduler is called with the asynchronous interrupts stack.
Moving the psw back to io_return instead fixes the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If irq flags tracing is enabled the TRACE_IRQS_ON macros expands to
a function call which clobbers registers %r0-%r5. The macro is used
in the code path for single stepped system calls. The argument
registers %r2-%r6 need to be restored from the stack before the system
call function is called.
Cc: stable@kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 there are two ways of specifying the system call number for
the svc instruction. The standard way is to use the immediate field
in the instruction (or to use EXecute for values unknown during
assemble time). This can encode 256 system calls.
The kernel ABI also allows to put the system call number in r1 and
then execute svc 0 to enable system call numbers > 255.
It turns out that single stepping svc 0 is broken, since the PER
program check handler uses r1. We have to use a different register.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (105 commits)
ring-buffer: only enable ring_buffer_swap_cpu when needed
ring-buffer: check for swapped buffers in start of committing
tracing: report error in trace if we fail to swap latency buffer
tracing: add trace_array_printk for internal tracers to use
tracing: pass around ring buffer instead of tracer
tracing: make tracing_reset safe for external use
tracing: use timestamp to determine start of latency traces
tracing: Remove mentioning of legacy latency_trace file from documentation
tracing/filters: Defer pred allocation, fix memory leak
tracing: remove users of tracing_reset
tracing: disable buffers and synchronize_sched before resetting
tracing: disable update max tracer while reading trace
tracing: print out start and stop in latency traces
ring-buffer: disable all cpu buffers when one finds a problem
ring-buffer: do not count discarded events
ring-buffer: remove ring_buffer_event_discard
ring-buffer: fix ring_buffer_read crossing pages
ring-buffer: remove unnecessary cpu_relax
ring-buffer: do not swap buffers during a commit
ring-buffer: do not reset while in a commit
...
The sysc_restore_trace_psw and io_restore_trace_psw storage locations
are created in the .text section. When creating and IPLing from a named
saved system (NSS), writing to these locations causes a protection exception
(because the .text section is mapped as shared read-only in the NSS).
To permit write access, move the storage locations into the .data section.
The problem occurs only when CONFIG_TRACE_IRQFLAGS is set.
The git commmit that has introduced these variables is:
411788ea7f
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s/HAVE_FTRACE_SYSCALLS/HAVE_SYSCALL_TRACEPOINTS/g
s/TIF_SYSCALL_FTRACE/TIF_SYSCALL_TRACEPOINT/g
The syscall enter/exit tracing is no longer specific to just ftrace, so
they now have names that reflect their tie to tracepoints instead.
Signed-off-by: Josh Stone <jistone@redhat.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <1251150194-1713-2-git-send-email-jistone@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
System call tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enable secure computing on s390 as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reset the cpu timer to the maximum value and correctly initialize the
cpu accounting values in the lowcore when the cpu is started.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Distinguish the cputime of the idle process where idle is actually using
cpu cycles from the cputime where idle is sleeping on an enabled wait psw.
The former is accounted as system time, the later as idle time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 we always want to run with precise cputime accounting.
Remove the config options VIRT_TIMER and VIRT_CPU_ACCOUNTING.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 we have ret_from_fork jump not to the "do all work we
normally do on return from syscall" as on x86, ppc, etc., but to the
"do all such work except audit". Historical reasons - the codepath
triggered when we have AUDIT process flag set is separated from the
normall one and they converge at sysc_return, which is the common
part of post-syscall work. And does not include calling audit_syscall_exit() -
that's done in the end of sysc_tracesys path, just before that path jumps
to sysc_return.
IOW, the child returning from fork()/clone()/vfork() doesn't
call audit_syscall_exit() at all, so no matter what we do with its
audit context, we are not going to see the audit entry.
The fix is simple: have ret_from_fork go to the point just past
the call of sys_.... in the 'we have AUDIT flag set' path. There we
have (64bit variant; for 31bit the situation is the same):
sysc_tracenogo:
tm __TI_flags+7(%r9),(_TIF_SYSCALL_TRACE|_TIF_SYSCALL_AUDIT)
jz sysc_return
la %r2,SP_PTREGS(%r15) # load pt_regs
larl %r14,sysc_return # return point is sysc_return
jg do_syscall_trace_exit
which is precisely what we need - check the flag, bugger off to sysc_return
if not set, otherwise call do_syscall_trace_exit() and bugger off to
sysc_return. r9 has just been properly set by ret_from_fork itself,
so we are fine.
Tested on s390x, seems to work fine. WARNING: it's been about
16 years since my last contact with 3X0 assembler[1], so additional
review would be very welcome. I don't think I've managed to screw it
up, but...
[1] that *was* in another country and besides, the box is dead...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
syscall_get_nr() currently returns a valid result only if the call
chain of the traced process includes do_syscall_trace_enter(). But
collect_syscall() can be called for any sleeping task, the result of
syscall_get_nr() in general is completely bogus.
To make syscall_get_nr() work for any sleeping task the traps field
in pt_regs is replace with svcnr - the system call number the process
is executing. If svcnr == 0 the process is not on a system call path.
The syscall_get_arguments and syscall_set_arguments use regs->gprs[2]
for the first system call parameter. This is incorrect since gprs[2]
may have been overwritten with the system call number if the call
chain includes do_syscall_trace_enter. Use regs->orig_gprs2 instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_IRQSOFF_TRACER the trace_hardirqs_off() function includes
a call to __builtin_return_address(1). But we calltrace_hardirqs_off()
from early entry code. There we have just a single stack frame.
So this results in a kernel stack backchain walk that would walk beyond
the kernel stack. Following the NULL terminated backchain this results
in a lowcore read access.
To fix this we simply call trace_hardirqs_off_caller() and pass the
current instruction pointer.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
mem_detect.c:(.text+0x10592): undefined reference to `lockdep_sys_exit'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* System call parameter and result access functions
* Add tracehook calls
* Split syscall_trace into two functions do_syscall_trace_enter and
do_syscall_trace_exit
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On return from syscall or interrupt, we have to check if we return to
userspace (likely) and if there is work todo (less likely) to decide
if we handle the work. We can optimize this check: we first check for
the less likely work case and then check for userspace.
This patch is also a preparation for an additional patch, that fixes a bug
in KVM dealing with cpu bound guests.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
TIF_RESTORE_SIGMASK no longer needs to be in the _TIF_WORK_* masks. Those low
bits are scarce, and are all used up now. Renumber TIF_RESTORE_SIGMASK to
free one up.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix couple of section mismatches. And since we touch the code
anyway change the IPL code to use C99 initializers.
Cc: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit b8e7a54cd0 introduced a compile
error if CONFIG_PREEMPT is not set:
arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
/space/kvm/arch/s390/kernel/entry.S:(.text+0xbfce): undefined reference to `preempt_schedule_irq'
This patch hides preempt_schedule_irq if CONFIG_PREEMPT is not set.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When returning from IRQ handling and TIF_NEED_RESCHED is set we must
call preempt_schedule_irq() instead of schedule().
Otherwise the BKL might be unlocked in schedule() and therfore
everything that relies on the BKL is broken.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Run the lockdep_sys_exit hook before returning to user space.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If a machine check is pending and the external or I/O interrupt handler
returns to userspace io_mcck_pending is going to call s390_handle_mcck.
Before this happens a call to TRACE_IRQS_ON was already made since we
know that we are going back to userspace and hence interrupts will be
enabled. So there was an indication that interrupts are enabled while
in reality they are still disabled.
s390_handle_mcck will do a local_irq_save/restore pair and confuse
lockdep which later complains about inconsistent irq tracing.
To solve this just call trace_hardirqs_off before calling
s390_handle_mcck and trace_hardirqs_on afterwards.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the in-kernel system call has been remove the system call path
can be optimized. The problem state bit of the old psw is always set
between system_call and sysc_do_svc. SAVE_ALL_SVC uses this information
to avoid two instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove system call glue for sys_clone, sys_fork, sys_vfork, sys_execve,
sys_sigreturn, sys_rt_sigreturn and sys_sigaltstack. Call do_execve from
kernel_execve directly, move pt_regs to the right place and branch to
sysc_return to start the user space program. This removes the last
in-kernel system call.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Heiko Carstens