Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
dwc3 controller only has USB2 ports enabled) we need to initialize the
USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
initialization high-speed USB devices (especially USB hard disks and
thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
USB2 PHY between host and peripheral (aka device) mode. an interrupt
can be used to detect changes between host and device mode.
There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
logic (on the GXL and GXM SoCs these are the same clock and reset line
as for the USB3 PHY itself, but Amlogic sees this as two different
components - even though they share the same register space - so they
have to be passed individually to allow specifying different inputs on
other SoCs if needed)
- the interrupt for the OTG detection logic
The whole OTG detection logic is not implemented yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
The USB2 PHY is a simple PHY which only has a few registers to configure
the mode (host/device) and a reset register (to enable/disable the PHY).
Unfortunately there are no datasheets available for this PHY. The driver
was written by reading the code from Amlogic's GPL kernel sources and
by analyzing the registers on an actual GXL and GXM device running the
kernel that was shipped on the boards I have.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Thomas Gleixner