This turns on the CONFIG_BCM2835_THERMAL as module for
Raspberry Pi 2 and 3.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi Zero W has an onboard BT chip (BCM43438). So enable the
necessary HCI UART driver (requires serial device bus).
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The CONFIG_LIRC symbol has changed from 'tristate' to 'bool, so we now
get a warning for omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:322:warning: symbol value 'm' invalid for LIRC
This changes the file to mark the symbol as built-in to get rid of the
warning.
Fixes: a60d64b15c ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds stm32 support to multi_v7_defconfig
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This changes CONFIG_DAVINCI_WATCHDOG from a module to a compiled-in
option. Since the reset function has been moved out of the mach code in
commit 94f2e94514 ("ARM: davinci: remove watchdog reset") and into the
watchdog driver, devices cannot reboot unless the watchdog driver is
loaded, so make it a compiled-in option so that we can always reboot, even
when modules are not loaded.
Cc: Sekhar Nori <nsekhar@ti.com>
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Re-sync the defconfig by doing:
make savedefconfig
cp defconfig arch/arm/configs/imx_v6_v7_defconfig
Checked that all the removed options are still enabled by Kconfig logic.
The exception is CONFIG_SOC_CAMERA_OV2640, which is only used by some
mx31 machines. As the mx3_camera driver has been removed from the kernel
tree, removing CONFIG_SOC_CAMERA_OV2640 is not an issue.
So keep it in sync to help further changes in defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Compile marvell_nand.c instead of pxa3xx_nand.c with all PXA based SoCs.
Convert all board files and defconfigs so that the new driver is used
everywhere instead of the old one.
Board files using CONFIG_MTD_NAND_PXA3xx now use CONFIG_MTD_NAND_MARVELL
instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This enables SYSCON_REBOOT_MODE as a module. This is used by LEGO
MINDSTORMS EV3 to reboot into a special firmware update mode.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Raspberry Pi 3 uses the 8250-based auxilary UART of the BCM2837 SoC
as the primary serial console of the board, so enable it in the
multiplatform defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The phyCORE-i.MX 6 uses the DA9062/63 PMIC, RTC and Watchdog driver.
Enable these options by default.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl udoo board has an AC97 codec.
Add support for it by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6UL EVK has support for the MAG3110 Magnetometer sensor, included
in its base board by default.
So add support for this Magnetometer in the imx_v6_v7_defconfig.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables configs for Trusted Execution Environment(TEE) and
Open Portable Trusted Execution Environment(OP-TEE).
With Linux running in Trustzone non-secure world, OP-TEE OS runs in
secure world, linux could use secure services provided by OP-TEE.
With TEE/OP-TEE options selected, use the bindings
in Documentation/devicetree/bindings/arm/firmware/linaro,optee-tz.txt
to let the driver probe work.
On i.MX6/7, now the bootflow is U-Boot->OP-TEE->Linux, OP-TEE will
automatically create that node.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform for,
the EP93xx based Liebherr controller BK3.1. It's a minor variation of
the EP93xx reference design and in active use, while EP93xx apparently
doesn't have enough new development to have any device tree support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=frm4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Pull irq updates from Thomas Gleixner:
"A rather small set of irq updates this time:
- removal of the old and now obsolete irq domain debugging code
- the new Goldfish PIC driver
- the usual pile of small fixes and updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Kill CONFIG_IRQ_DOMAIN_DEBUG
irq/work: Improve the flag definitions
irqchip/gic-v3: Fix the driver probe() fail due to disabled GICC entry
irqchip/irq-goldfish-pic: Add Goldfish PIC driver
dt-bindings/goldfish-pic: Add device tree binding for Goldfish PIC driver
irqchip/ompic: fix return value check in ompic_of_init()
dt-bindings/bcm283x: Define polarity of per-cpu interrupts
irqchip/irq-bcm2836: Add support for DT interrupt polarity
dt-bindings/bcm2836-l1-intc: Add interrupt polarity support
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
It doesn't actually do anything. Merge its help text into
EXTRA_FIRMWARE.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Fixes: 0946b2fb38 ("firmware: cleanup FIRMWARE_IN_KERNEL message")
Signed-off-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_IRQ_DOMAIN_DEBUG is similar to CONFIG_GENERIC_IRQ_DEBUGFS,
just with less information.
Spring cleanup time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Link: https://lkml.kernel.org/r/20180117142647.23622-1-marc.zyngier@arm.com
The DRM driver most notably, but also out of tree drivers (for now) like
the VPU or GPU drivers, are quite big consumers of large, contiguous memory
buffers. However, the sunxi_defconfig doesn't enable CMA in order to
mitigate that, which makes them almost unusable.
Enable it to make sure it somewhat works.
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Choose to compile and embed marvell_nand.c as NAND controller driver
instead of the legacy pxa3xx_nand.c for platforms with Marvell EBU
SoCs.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- Enable CPU_FREQ_STAT for cpufreq transtion statistics support.
- Enable SRTC driver RTC_DRV_MXC_V2 for i.MX53.
- Turn on a few drivers useful for DART-MX6 SoM support, SERDEV
bluetooth, SERIAL_DEV_BUS, WL18XX, and DEFAULT_ON LED Trigger.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaUDsIAAoJEFBXWFqHsHzORfIH/RQf/Kg7HHFd78qk7TVIbfIK
uH/YspvDReV5cDdiJIoTQiAZTC6MvdlGtG/PevrQHA6F7jjJdRNhwS6VT1pCaidg
pS52OSWIUqFrYdTPuBCyF/tS7lPsiKm74YZzePBUKBz9EEhsTs9bAcL4J6WGkPAN
GcIxe0PG7/SzFQFJMomND4Of2Idru4HP5OHlJFY2K68rVgpdn7DA3+cA2ChB8Ajm
vR9JJO58DwPpNtXf1KiyMur+srKsSn1bvJdu7qvYReNYPHxc6semKo82KgznmNfu
tSfPcDpKOyvYtSEa02TSV5Y1MTtmgTSFcrwh3/SzGZ7qurbkQtS4Cc1YGo5q47A=
=5J9f
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
i.MX defconfig updates for 4.16:
- Enable CPU_FREQ_STAT for cpufreq transtion statistics support.
- Enable SRTC driver RTC_DRV_MXC_V2 for i.MX53.
- Turn on a few drivers useful for DART-MX6 SoM support, SERDEV
bluetooth, SERIAL_DEV_BUS, WL18XX, and DEFAULT_ON LED Trigger.
* tag 'imx-defconfig-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
Signed-off-by: Olof Johansson <olof@lixom.net>
It is very useful for user to retrieve cpufreq transtion statistics
and worth to be default enabled.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
data structures, removal of unnecessary newlines from gpio labels and code
simplification.
Also a defconfig update for DaVinci, enabling support for USB network adaptors.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oZrM
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.16/soc-v2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Pull "TI DaVinci SoC support updates for v4.16" from Sekhar Nori:
DaVinci SoC updates consisting of non-critical bug fixes including constifying
data structures, removal of unnecessary newlines from gpio labels and code
simplification.
Also a defconfig update for DaVinci, enabling support for USB network adaptors.
* tag 'davinci-for-v4.16/soc-v2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
ARM: davinci: Use PTR_ERR_OR_ZERO()
ARM: davinci: make davinci_soc_info structures const
ARM: davinci: make argument to davinci_common_init() as const
ARM: davinci_all_defconfig: enable support for USB network adaptors
These are to configure dra7 PCIe for omap2plus_defconfig and
multi_v7_defconfig.
-----BEGIN PGP SIGNATURE-----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=jl6W
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Two defconfig updates for omaps
These are to configure dra7 PCIe for omap2plus_defconfig and
multi_v7_defconfig.
* tag 'omap-for-v4.16/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: multi_v7_defconfig: Enable CONFIG_PCI_DRA7XX (Host & Device modes)
ARM: omap2plus_defconfig: Enable CONFIG_PCI_DRA7XX (Host & Device modes)
Signed-off-by: Olof Johansson <olof@lixom.net>
shmobile_defconfig:
* Enable PWM timers, which are present on R-Car and RZ/G1 platforms,
as a built-in
* Enable SGTL5000 audio codec, which is present on the he iWave RZ/G1M Q7
carrier board, as a built-in
multi_v7_defconfig:
* Enable PWM timers, which are present on R-Car and RZ/G1 platforms,
as a module
-----BEGIN PGP SIGNATURE-----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=7Fzq
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Defconfig Updates for v4.16
shmobile_defconfig:
* Enable PWM timers, which are present on R-Car and RZ/G1 platforms,
as a built-in
* Enable SGTL5000 audio codec, which is present on the he iWave RZ/G1M Q7
carrier board, as a built-in
multi_v7_defconfig:
* Enable PWM timers, which are present on R-Car and RZ/G1 platforms,
as a module
* tag 'renesas-defconfig-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: defconfig: Enable PWM
ARM: multi_v7_defconfig: Select PWM_RCAR as module
ARM: shmobile: defconfig: Enable SGTL5000 audio codec
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the missing configs for the DART-MX6 SoM support :
- SERDEV bluetooth driver + SERIAL_DEV_BUS configs
- WL18XX driver
- DEFAULT_ON Led Trigger
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds framebuffer console support to qcom defconfig.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
MSM IOMMU is required for apq8064 display, so enable it by default.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This enables DRM Kconfig for apq8064 display.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
based crypto and droid 4 USB PHY.
-----BEGIN PGP SIGNATURE-----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=gD3r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/defconfig-v2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "One old minor pull request pending" from Tony Lindgren:
Few omap2plus_defconfig changes for v4.15 merge window to enable NEON
based crypto and droid 4 USB PHY.
* tag 'omap-for-v4.15/defconfig-v2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable droid 4 USB PHY
ARM: omap2plus_defconfig: enable NEON based crypto
Enable CONFIG_PCI_DRA7XX in order to be able to configure PCIe
controller present in dra7 SoCs in both host mode and device mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable CONFIG_PCI_DRA7XX in order to be able to configure PCIe
controller present in dra7 SoCs in both host mode and device mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
RZ/G1 and R-Car platforms have PWM timers. This patch enables PWM support
by default.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable PWM support for R-Car and friends by default.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The iWave RZ/G1M Q7 carrier board supports I2S audio codec "SGTL5000".
To increase hardware support enable the driver in the shmobile_defconfig
multiplatform configuration.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
EXYNOS_IOMMU is disabled in exynos_defconfig since it was known to cause
boot failures on Exynos Chromebooks. The recommendation was for IOMMU to
be enabled manually on systems as needed.
A recent exynos_drm change added a warning message when EXYNOS_IOMMU is
disabled. It is necessary to enable it to avoid the warning messages.
A few initial tests have shown that enabling EXYNOS_IOMMU might be safe
on Exynos Chrome-books.
Due to some other changes in the order of operations during boot
process, power domains are initialized very early and because of the
temporary lack of devices (which are not yet added to the system), are
turned off.
This practically stops FIMD for scanning framebuffer very early during
boot, before IOMMU gets initialized and "solves" the issue, which was
the reason to disable Exynos IOMMU by default on Exynos Snow Chromebooks.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Extend message with Marek Szyprowski's explanation]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable drivers for QSPI, LEDS, gpio-decoder that are present on 66AK2G EVM
and 66AK2G ICE boards.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Enable following drivers for recently merged devices:
- CEC and S5P CEC driver for all Exynos4 and Exynos5 boards with HDMI
- Sii9234 DRM HDMI-MHL bridge for Trats2
- dedicated Odroid ASoC machine driver for Odroid XU3/XU4
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable following drivers for recently merged devices:
- perf events and ARM PMU (Performance Measurement Unit) driver for all
Exynos boards
- CEC and S5P CEC driver for all Exynos4 and Exynos5 boards with HDMI
- Sii9234 DRM HDMI-MHL bridge for Trats2
- dedicated Odroid ASoC machine driver for Odroid XU3/XU4
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enables CONFIG_USB_USBNET so that well known USB network adapters
can enumerate as network interfaces.
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
The RPMSG_VIRTIO is now user selectable option so we explicitly
select it in multi_v7_defconfig. Till now RPMSG_VIRTIO was
selected by ST_REMOTEPROC=m in multi_v7_defconfig.
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A new driver has been developed to support the CESA IP. Switch
remaining users of the old driver to the new driver in order to remove
the old one.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Turn on DRM_DW_HDMI_CEC option to get HDMI CEC support.
- Enable MUX_MMIO to get ADV7180 probe on Gateworks GW51xx boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ7y5xAAoJEFBXWFqHsHzOnuIH/0ftbQ5pKFdWZ4y/UiR5JpYA
hYz2RlgS4m3DbrC8xC8b6MGRBeLr7clSxXlnXfpyASZVmfYhDNaoMFdKtTJpSYxe
rnvhi1ePhb2oq4orjPFzM212eFoIhKEzvwdNyMyLlHM9xqoBGLkcHDJ/6pt96car
JkCoFtQgpy4i0FAV+HNtuE//n0hQAWzXJ7E8Nc00pkwuzWA1HQC1GyAOzsSaIGyR
dQxCxiL9AZGVD8awUnFb39Hme1FIZaP+taz+JFFuTLNE+c/0xQDUi4BTpJxiyWKK
rQrZ1ZUHMOJZ7h55G46paahSqVwN/bxq8nTXoPnaVPHQc+pFOS9X5aUzZKczOJU=
=8Xwg
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Pull "i.MX defconfig updates for 4.15" from Shawn Guo:
- Turn on DRM_DW_HDMI_CEC option to get HDMI CEC support.
- Enable MUX_MMIO to get ADV7180 probe on Gateworks GW51xx boards.
* tag 'imx-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Select the CEC driver
ARM: imx_v6_v7_defconfig: Select CONFIG_MUX_MMIO
Let's enable this as loadable module for droid 4.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SX150X GPIO expander has been moved to pin control and
its Kconfig symbol has been renamed. We used to have a paper-over
thing in Kconfig but it was causing circular dependencies so
I have had to kill it off. Select the right driver instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Enable Sony Z2 tablet options
* Enable USB on APQ8064/MSM8974
* Fixup/catchup config to support newer options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=90WE
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/soc
Pull "Qualcomm ARM Based defconfig Updates for v4.15" from Andy Gross:
* Enable Sony Z2 tablet options
* Enable USB on APQ8064/MSM8974
* Fixup/catchup config to support newer options
* tag 'qcom-defconfig-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: qcom_defconfig: Enable Z2 Tablet related options
ARM: qcom_defconfig: Disable DEBUG_GPIO
ARM: qcom_defconfig: Enable configs for USB on apq8064/msm8974
ARM: qcom_defconfig: Resync with new Kconfig options
1. Enable USB3503 on multi_v7 for Odroid U3.
2. Enable USB Attached SCSI for Odroid HC1.
-----BEGIN PGP SIGNATURE-----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=+nLs
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Pull "Samsung defconfig changes for v4.15" from Krzysztof Kozłowski:
1. Enable USB3503 on multi_v7 for Odroid U3.
2. Enable USB Attached SCSI for Odroid HC1.
* tag 'samsung-defconfig-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Enable UAS support for Odroid HC1 board
ARM: exynos_defconfig: Enable UAS support for Odroid HC1 board
ARM: multi_v7_defconfig: Enable USB3503 driver
Enable BQ32000 RTC driver in multi_v7_defconfig.
Biju Das says, "The iWave RZ/G1M Q7 SOM supports RTC (TI BQ32000).
To increase hardware support enable the driver in the
multi_v7_defconfig multiplatform configuration."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9Ep1
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Defconfig Updates for v4.15" from Simon Horman:
Enable BQ32000 RTC driver in multi_v7_defconfig.
Biju Das says, "The iWave RZ/G1M Q7 SOM supports RTC (TI BQ32000).
To increase hardware support enable the driver in the
multi_v7_defconfig multiplatform configuration."
* tag 'renesas-defconfig-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: multi_v7_defconfig: Enable BQ32000 RTC driver
Select CONFIG_DRM_DW_HDMI_CEC option, so that the CEC driver can be
loaded by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Turn on Broadcom Hurrican 2 SoC support by default to get access to its
drivers.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the new Amlogic Meson MX SDIO/MMC controller driver, which
typically connects to the SD card and SDIO wifi module.
The driver is enabled as built-in to allow booting from the SD card.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Select the options necessary to get USB, coincell, WiFI, touchscreen and
backlight on the Z2 Tablet (and other family B devices) working. The
device specific peripherals are selected as modules.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
GPIO debug spams the kernel log quite a bit, so remove this from the
default Qualcomm defconfig.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the regulator driver, usb phy drivers, and hsic hub driver
to support USB devices on apq8064 and msm8974.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
CONFIG_HWSPINLOCK must be selected explicitly for SMEM and its
dependencies to be enabled.
The update is generated by "make savedefconfig" and as such reflects
changes to the implicit state of other options, as of v4.14-rc1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable PWM_TIECAP driver to support ECAP IP present in 66AK2G SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Odroid HC1 board has built-in JMicron USB to SATA bridge, which supports
UAS protocol. Enable support for it to make sure that all built-in storage
devices are available. Enable it as module to keep in line with multi_v7
policy to enable drivers as build-in only if they are critical for boot
process. On Odroid HC1 the kernel itself has to be still read from the
SD-card, so assume that modules/initrd is also accessible there.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This updates the Gemini defconfig with drivers merged
for v4.13 or v4.14:
- ATA driver is merged
- DMA driver is merged
- RTC driver gets selected from default Kconfig
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
It is no longer possible to load this at runtime, so let's
change the few remaining users to have it built-in all
the time.
arch/arm/configs/zeus_defconfig:115:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/viper_defconfig:116:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/pxa_defconfig:474:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
Reported-by: kernelci.org bot <bot@kernelci.org>
Fixes: 6104c37094 ("fbcon: Make fbcon a built-time depency for fbdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable kernel mode NEON and the various NEON based crypto algorithms,
which are between 1.4x (AES-XTS) and 2.4x (AES-GCM) faster than
scalar code (measured on Cortex-A8).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Odroid HC1 board has built-in JMicron USB to SATA bridge, which supports
UAS protocol. Compile-in support for it (instead of enabling it as module)
to make sure that all built-in storage devices are available for rootfs.
The bridge itself also supports fallback to standard USB Mass Storage
protocol, but USB Mass Storage class doesn't bind to it when UAS is
compiled as module and modules are not (yet) available.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Odroid U3 (Exynos 4412 based) for instance needs this driver,
otherwise its USB hub will not come up.
Also selecting it as built-in to allow booting from USB without
an initrd/initramfs.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
In order to get ADV7180 analog video decoder to probe on a Gateworks
GW51xx we need select CONFIG_MUX_MMIO, otherwise /dev/media node does
not get created.
Select CONFIG_MUX_MMIO, so that the ADV7180 driver can be correctly
probed.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Suggested-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the CMA and DMA_CMA Kconfig options by default for
Davinci platforms. Davinci remoteproc driver is one of the
modules that depends on these options, and this allows the
driver to be made visible for selection with menuconfig.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is some disagreement between the partition table map in Linux
for the DA850-EVM and the corresponding partition map in U-Boot.
To prevent breaking the Kernel, this patch enables MTD_CMDLINE_PARTS
which will allow the U-Boot to pass the partition map so future partitions
match without breaking backwards compatibility.
While at it, also sync to savedefconfig which leads to removal of
CONFIG_MMC_BLOCK_BOUNCE.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The iWave RZ/G1M Q7 SOM supports RTC (TI BQ32000).
To increase hardware support enable the driver in the
multi_v7_defconfig multiplatform configuration.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Texas Instruments DAC7512 has the exact same pinout, programming
interface and power-down modes as the Texas Instruments DAC121S101 and
Analog Devices AD5320, which are already supported by the IIO driver
ad5446.c. Remove the duplicate misc driver.
This requires user space to migrate to the standardized IIO sysfs ABI.
(In other words, it needs to change a filename.)
The IIO driver supports the chip's features more fully, e.g. the ability
to power down the output or choose one of the available powerdown modes.
There is an oddity with the misc driver in that it initializes the SPI
slave to SPI_MODE_0, in contradiction to the datasheet which specifies
that data is latched in on the falling edge, implying that SPI_MODE_1
or SPI_MODE_2 must be used. Another oddity is that Kconfig and the
MODULE_DESCRIPTION() claim the chip has 16-bit resolution although it
actually has 12-bit.
Datasheets:
http://www.ti.com/lit/ds/symlink/dac7512.pdfhttp://www.ti.com/lit/ds/symlink/dac121s101.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This branch contains platform updates for 32- and 64-bit ARM,
including defconfig updates to enable new options, drivers and
platforms. There are also a few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale DMA code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=g8cF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 SoC platform updates from Olof Johansson: "This branch
contains platform updates for 32- and 64-bit ARM, including defconfig
updates to enable new options, drivers and platforms. There are also a
few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other
drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale
DMA code"
* tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: multi_v7_defconfig: make eSDHC driver built-in
arm64: defconfig: enable rockchip graphics
MAINTAINERS: Update Cavium ThunderX2 entry
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
ARM: s3c24xx: Fix NAND ECC mode for mini2440 board
ARM: davinci_all_defconfig: enable tinydrm and ST7586
arm64: defconfig: Enable QCOM IPQ8074 clock and pinctrl
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
MAINTAINERS: update ARM/ZTE entry
soc: versatile: remove unnecessary static in realview_soc_probe()
ARM: Convert to using %pOF instead of full_name
ARM: hisi: Fix typo in comment
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add recently added crypto drivers as modules
arm64: defconfig: enable CONFIG_UNIPHIER_WATCHDOG
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZsSBoAAoJEAhfPr2O5OEVDc4QAJZSuVYmyLgvtmPxhyqgCvkz
I0DmWM4ZtK2VT/xJ/AA23z8IiLKi2+pDC0Xx6/aIiA665cyl3oPUdkKIaHW9Z6+A
fV8gSFkmGkluQb9mP/KdHYI2oSeEv2ivCa1kfaApYcoBa904z8uU++z15Iu5p/+m
fjpc2vnc9rax0Vuwmgv7p1CL4j4e/ja0siCSCGbu2ad50KqP4ytnBooNPQOQt89D
L+Av5MeGml/CTUUnAFjWfSmQ72Ht8GhoBBKc6wGoq9x3GTckDDTqy8BAqGt4UQnu
fR0mb71zuSVmTjxRe7tc/74m3ReaeSHzQeHJhjdQslvNmV3RVQgk/6CCsmqNEegr
rbC3glQCM+gp5YywCjRL6DCPsoqvjexLtPQjMZIGYxgSYQUyXGOxilgmj9+73761
6aOl0nqdgN+vlWzaSeDF9EQxRsc+cCq/Po8/xuPE/Pzs6zTQwU+6b+ADLf9jCyDP
LTC49wOj24SoWiTlG1FTct2ogZ3h5wNPWlurBtmyiFJn+43RpsH5IW9wLilCjeiE
6JeCWEIBglCCq/TVCzETKNSaixDL6/lMQ9uRdCpIO4VLyoS6S9pZASNPBmQ1h7h/
oTjYDeWirIthNOccstbBoJQYSX62CqAIW3wq5ME6PAgM+ioiLXLYk0fV3yBKoBNW
Z0SBeTcuPxWmfzuxMtik
=fNM2
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Brazil's Independence Day pull request :-)
This is one of the biggest media pull requests, with 625 patches
affecting almost all parts of media (RC, DVB, V4L2, CEC, docs).
This contains:
- A lot of new drivers:
* DVB frontends: mxl5xx, stv0910, stv6111;
* camera flash: as3645a led driver;
* HDMI receiver: adv748X;
* camera sensor: Omnivision 6650 5M driver (ov6650);
* HDMI CEC: ao-cec meson driver;
* V4L2: Qualcom camss driver;
* Remote controller: gpio-ir-tx, pwm-ir-tx and zx-irdec drivers.
- The DDbridge DVB driver got a massive update, with makes it in sync
with modern hardware from that vendor;
- There's an important milestone on this series: the DVB
documentation was written in 2003, but only started to be updated
in 2007. It also used to contain several gaps from the time it was
kept out of tree, mentioning error codes and device nodes that
never existed upstream. On this series, it received a massive
update: all non-deprecated digital TV APIs are now in sync with the
current implementation;
- Some DVB APIs that aren't used by any upstream driver got removed;
- Other parts of the media documentation algo got updated, fixing
some bugs on its PDF output and making it compatible with Sphinx
version 1.6.
As the number of hacks required to build PDF output reduced, I hope
we'll have less troubles as newer versions of our documentation
toolchain are released (famous last words);
- As usual, lots of driver cleanups and improvements"
* tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (624 commits)
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
media: add qcom_camss.rst to v4l-drivers rst file
media: dvb headers: make checkpatch happier
media: dvb uapi: move frontend legacy API to another part of the book
media: pixfmt-srggb12p.rst: better format the table for PDF output
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
media: index.rst: don't write "Contents:" on PDF output
media: pixfmt*.rst: replace a two dots by a comma
media: vidioc-g-fmt.rst: adjust table format
media: vivid.rst: add a blank line to correct ReST format
media: v4l2 uapi book: get rid of driver programming's chapter
media: format.rst: use the right markup for important notes
media: docs-rst: cardlists: change their format to flat-tables
media: em28xx-cardlist.rst: update to reflect last changes
media: v4l2-event.rst: adjust table to fit on PDF output
media: docs: don't show ToC for each part on PDF output
...
Sometimes root file system is deployed on SD card. It's
proper to build eSDHC driver into kernel.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable new Aspeed drivers for i2c, lpc snoop and vuart
- Set VMSPLIT_2G for ast2400 platforms, required for mtd driver
-----BEGIN PGP SIGNATURE-----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=brUg
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.14-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/defconfig
Pull "Aspeed defconfig updates for 4.14" from Joel Stanley:
- Enable new Aspeed drivers for i2c, lpc snoop and vuart
- Set VMSPLIT_2G for ast2400 platforms, required for mtd driver
* tag 'aspeed-4.14-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
These drivers have been recently upstreamed, so add them to the
defconfigs.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is required for the SMC controller mapping windows on the AHB
Bus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This enables the tinydrm and ST7586 panel modules used by the display
on LEGO MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Enables the ChipIdea UDC driver and selects some symbols that were
previously being selected by other drivers but will no longer be in
v4.14.
-----BEGIN PGP SIGNATURE-----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=mYch
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.14-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/defconfig
Pull "ARM: tegra: Default configuration updates for v4.14-rc1" from Thierry Reding:
Enables the ChipIdea UDC driver and selects some symbols that were
previously being selected by other drivers but will no longer be in
v4.14.
* tag 'tegra-for-4.14-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
- Enable SPI_GPIO and GPIO_74X164 support which are useful for some
boards like imx7d-sabresd.
- Enable build of CODA video codec and staging video4linux drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZloiPAAoJEFBXWFqHsHzOK9AH/2m3J8waqDJW1ln6emcBCB7X
2LSHk+66UGN+V4rchXHtrdfjjrpszaRtregW29qCYqwATA+ZEmtCey6MR/8krzBk
exjYOfZTDXvAqnVnbr5JT+/PWVzDKCLHLSVEMXZ3V2ylM0ps4Pdb1G19RxWg58HO
tE69x1lIyHEphpaZ/xvVuD7k8BrTBYdgVn41qwlzZwZsiHIXLSih3wirxX911C11
V3yWoFAG9NZ1qjIJEYn1m/wtpWtyUu8IRDiZlHyodlR+ffeE43Hgh2+Ih/lqyKrm
SH4U0fN0D7Tta08/2MvPeHsGCnppk4kWs0tZDafUd8qOb+MPi3NzNDI2Y7QRktM=
=ljhX
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
Pull "i.MX defconfig updates for 4.14" from Shawn Guo:
- Enable SPI_GPIO and GPIO_74X164 support which are useful for some
boards like imx7d-sabresd.
- Enable build of CODA video codec and staging video4linux drivers.
* tag 'imx-defconfig-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable staging video4linux drivers
ARM: imx_v6_v7_defconfig: Select the coda driver as module
ARM: imx_v6_v7_defconfig: Enable GPIO_74X164
ARM: imx_v6_v7_defconfig: Enable SPI_GPIO
for 4.14, please pull the following:
- Markus enables the Broadcom STB AVS thermal monitoring driver as a module
which is currently queued in Rui Zhang's tree
- Stefan updates the bcm2835_defconfig to contain a few useful changes: the RPI
mini UART is enabled by default, the default CMA pool is bumped up to 32MB to
support VC4 usages and finally BRCMFMAC is enabled as module since this is the
wireless driver used on Raspberry Pi Zero Wireless.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJZldaIAAoJEIfQlpxEBwcEaVMP/3MVHki9bl11DJVKmnF/itNa
lGASCwdP+zHlBOtazBuDXxymrfZtn0xYPv+m5A/dzuMp7NJUeW7xuefk/hxeGLhA
43VslCu/w6TKduhBykP1u0ktZHTz/esx71/Eb6wxLDzOnCXrhICoe1npp91othlo
EmvsZx2hinjvNqVxPxcJOb/QLJdJaGkoclRTWNX57N9D1HMNnSTz5+FGzYEHYY86
ud0DMTxHRZ1KeYQBto9Q6YdKspecSKCxXc2/Ir/k7dQ+ZOp5jSzS7nU7rZ3UsuBY
SLhEcEwHPq2RXq5vZlRy/QcFwodi6BeWz6Ig18P3mJ2RVzCvx5GlGjpKdLS9WpIo
jkUNav6k8R5Ygl+eWmcKX66JVSrELj81pEsznikM1ExGcI3EBhhTARHrol3NOmgh
ZkH3OrFwz2MuKhhE8TJ14uPo5pa/SvECNWNXmgiWJOr0CO/XjhYxWE5lGbVOv1/R
W8B0A2jrUh7lP7ziFfiREhSHJ2V3Br/q/ORi2N5atTggdVsZLQ4tltoozKcr+FmB
z9eEAqeVY6kYePVbRkUjsMj/hzJgu3OGmsWBsbTKGkzvHSGLXL0n/A920zLuvyM3
QEfqJexrTp5nH8JjnjXA/SS3qApeZXKScL3vhfO5wWHyvSaxJwzMj9YrBnpghYPb
54aPGnolFtzNc8NIQx/e
=+2/I
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/defconfig' of http://github.com/Broadcom/stblinux into next/defconfig
Pull "Broadcom defconfig changes for 4.14" from Florian Fainelli:
This pull request contains defconfig file changes for Broadcom ARM-based SoCs
for 4.14, please pull the following:
- Markus enables the Broadcom STB AVS thermal monitoring driver as a module
which is currently queued in Rui Zhang's tree
- Stefan updates the bcm2835_defconfig to contain a few useful changes: the RPI
mini UART is enabled by default, the default CMA pool is bumped up to 32MB to
support VC4 usages and finally BRCMFMAC is enabled as module since this is the
wireless driver used on Raspberry Pi Zero Wireless.
* tag 'arm-soc/for-4.14/defconfig' of http://github.com/Broadcom/stblinux:
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
ARM: bcm2835_defconfig: Enable wifi driver for RPi Zero W
ARM: bcm2835_defconfig: Increase CMA for VC4
ARM: bcm2835_defconfig: Enable Mini UART console support
Stefan Wahren