Commit Graph

251 Commits

Author SHA1 Message Date
Paul Mackerras e9a4b6a3f6 Merge branch 'linux-2.6' 2008-06-30 10:16:50 +10:00
Vitaly Bordug 2308c954f5 powerpc/85xx: Update pin setup for 8560ads
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.

Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-26 01:49:07 -05:00
Wolfgang Grandegger 6dd1b64a26 powerpc/85xx: add board support for the TQM8548 modules
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:33:53 -05:00
Wolfgang Grandegger 4fb035f69e powerpc/85xx: correct vendor prefix in DTS files for TQM85xx modules
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:33:11 -05:00
Kumar Gala c4ea896476 [POWERPC] 85xx: MPC85xx MDS - Unconditionally select PHYLIB for board fixups
The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.

Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.

So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support.  This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-09 08:45:07 -05:00
Jason Jin 741edc4949 [POWERPC] 85xx: Enable MSI support for 85xxds board
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:24 -05:00
Jeremy McNicoll bfd123bf91 [POWERPC] 85xx: SBC8548 - Add flash support and HW Rev reporting
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.

Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.

Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Andy Fleming 73f5b8f942 [POWERPC] 85xx: Fix some sparse warnings for 85xx MDS
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Andy Fleming 94833a4276 [POWERPC] 85xx: Add 8568 PHY workarounds to board code
The 8568 MDS needs some configuration changes to the PHY in order to
work properly.  These are done in the firmware, normally, but Linux
shouldn't need to rely on the firmware running such things (someone
could disable the PHY support in the firmware to save space, for instance).

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Kumar Gala a5dc66e2ab [POWERPC] 85xx: Fix compile warning
arch/powerpc/platforms/85xx/mpc85xx_ads.c: In function ‘init_ioports’:
arch/powerpc/platforms/85xx/mpc85xx_ads.c:168: warning: initialization discards qualifiers from pointer target type

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:41 -05:00
Scott Wood 3dd82a1ea7 [POWERPC] CPM: Always use new binding.
The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:40 -05:00
Sebastian Siewior 1028d4f162 [POWERPC] 85xx: Enable DMA engine on the MPC8544 DS
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:36 -05:00
Harvey Harrison e48b1b452f [POWERPC] Replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-01 20:43:09 +11:00
Alexandr Smirnov 22b619eee5 [POWERPC] 85xx: Emerson KSI8560 base support
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.

The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.

Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-26 11:30:45 -05:00
Kumar Gala 77b41597e8 [POWERPC] 85xx: convert sbc85* boards to use machine_device_initcall
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 13:15:26 -06:00
Kumar Gala 3a83156bd8 [POWERPC] 85xx: rework platform Kconfig
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
  all 85xx boards except sbc8560 and stx_gp3 since these to boards have
  board specific ifdef in driver code that may break all other boards

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 13:13:12 -06:00
Anton Vorontsov a2dd70a11d [POWERPC] QE: get rid of most device_types and model
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".

Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:32:55 -06:00
Kumar Gala f67be814ff [POWERPC] 85xx: some minor cleanups for stx_gp3 and tqm85xx
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:32:53 -06:00
Paul Gortmaker 0e0fffe887 [POWERPC] 85xx: Add basic support for Wind River SBC8548 board
This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc.  It closely follows the implementation of the MPC8548CDS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:30:50 -06:00
Paul Gortmaker b8b3caf3b4 [POWERPC] CPM2: Make support for the CPM2 optional on 8560 based boards
Currently there is no way to disable the CPM2 support.  Some boards,
like the SBC8560 have their own external UART and don't have any direct
dependencies on the CPM for a serial console or anything else.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:30:48 -06:00
Paul Gortmaker 2c19806122 [POWERPC] 85xx: Add support for Wind River SBC8560 in arch/powerpc
This adds support for the Wind River SBC8560 board, implemented as
powerpc.  It closely follows the implementation of the MPC8560ADS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:30:46 -06:00
Kumar Gala 0052bc5d5c [POWERPC] 85xx: Port TQM85xx boards over from arch/ppc
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-27 14:10:37 -06:00
Kumar Gala 77e03a2241 [POWERPC] 85xx: Port STX GP3 board over from arch/ppc
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-27 14:10:36 -06:00
Paul Gortmaker e5091842dc [POWERPC] 85xx: mpc85xx_ads: add in missing of_node_put()
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23 19:34:18 -06:00
Kumar Gala 277982e2d8 [POWERPC] 85xx: convert boards to use machine_device_initcall
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23 19:32:37 -06:00
Jon Loeliger 882407b979 [POWERPC] 8xxx: Convert #include of asm/of_{platform, device}.h into linux/of_{platform, device}.h.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-12-11 13:57:17 -06:00
Stephen Rothwell 44ef339073 [POWERPC] pci_controller->arch_data really is a struct device_node *
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-12-11 13:42:37 +11:00
Kumar Gala 0bfd5df53a [POWERPC] 85xx: Killed <asm/mpc85xx.h>
asm-powerpc/mpc85xx.h was really a hold over from arch/ppc.  Now that
more decoupling has occurred we can remove <asm/mpc85xx.h> and some of
its legacy.

As part of this we moved the definition of CPM_MAP_ADDR into cpm2.h
for 85xx platforms.  This is a stop gap until drivers stop using
CPM_MAP_ADDR.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-11 09:14:31 -05:00
Scott Wood 8abc8f5f1e [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-11 09:14:31 -05:00
Anton Vorontsov 803dedb608 [POWERPC] 85xx: mpc85xx_mds - reset UCC ethernet properly
Apart from that the current code doesn't compile it's also
meaningless with regard to the MPC8568E-MDS' BCSR.

This patch used to reset UCCs properly.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-08 08:39:07 -05:00
Anton Vorontsov cccd21027c [POWERPC] QEIC: Implement pluggable handlers, fix MPIC cascading
set_irq_chained_handler overwrites MPIC's handle_irq function
(handle_fasteoi_irq) thus MPIC never gets eoi event from the
cascaded IRQ. This situation hangs MPIC on MPC8568E.

To solve this problem efficiently, QEIC needs pluggable handlers,
specific to the underlaying interrupt controller.

Patch extends qe_ic_init() function to accept low and high interrupt
handlers. To avoid #ifdefs, stack of interrupt handlers specified in
the header file and functions are marked 'static inline', thus
handlers are compiled-in only if actually used (in the board file).
Another option would be to lookup for parent controller and
automatically detect handlers (will waste text size because of
never used handlers, so this option abolished).

qe_ic_init() also changed in regard to support multiplexed high/low
lines as found in MPC8568E-MDS, plus qe_ic_cascade_muxed_mpic()
handler implemented appropriately.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-08 08:38:57 -05:00
Anton Vorontsov 55f9ed0f6a [POWERPC] mpc85xx_mds: select QUICC_ENGINE
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-08 08:38:54 -05:00
Kumar Gala e1c1575f83 [POWERPC] 85xx/86xx: refactor RSTCR reset code
On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board.  We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-08 08:38:47 -05:00
Kumar Gala c9438affcb [POWERPC] Use for_each_ matching routinues for pci PHBs
On the Freescale embedded (83xx, 85xx, 86xx) and a few of the discrete
bridges (mpc10x, tsi108) use the new for_each_compatible_node() or
for_each_node_by_type() to provide more exact matching when looking for
PHBs in the device tree.

With the previous code it was possible to match on pci bridges since
we were only matching on device_type.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-08 08:38:40 -05:00
Kumar Gala 5d54ddcbcf [POWERPC] 85xx: Add basic Uniprocessor MPC8572 DS port
Added basic board port for MPC8572 DS reference platform that is
similiar to the MPC8544/33 DS reference platform in uniprocessor mode.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-09-14 08:51:54 -05:00
Jon Loeliger 683d00b03e [POWERPC] 85xx: Remove unnecessary loops_per_jiffy initialization code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-09-14 08:51:36 -05:00
Kumar Gala 7f50382dc8 [POWERPC] 85xx: Clean up from 85xx_ds rename
Renamed functions in 85xx_ds from 8544 to 85xx.

Kept an unique machine def/probe for the MPC8544 DS board to
handle some subtle differences between the future board based
on the DS platform.

Also fixed building w/o CONFIG_PCI and minor whitespace fixes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-09-13 15:45:03 -05:00
Kumar Gala 16d24060d1 [POWERPC] 85xx: Renamed mpc8544_ds.c to mpc85xx_ds.c
Renamed the mpc8544_ds.c board code to mpc85xx_ds.c to make it more
generic in prep for other boards based on the same platform.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-09-13 15:43:48 -05:00
Paul Mackerras b2315372ea Merge branch 'linux-2.6' into for-2.6.24 2007-09-14 01:24:25 +10:00
Kumar Gala 2af8569dc9 [POWERPC] 8{5,6}xx: Fix build issue with !CONFIG_PCI
We needed some ifdef CONFIG_PCI protection for pcibios_fixup so we
can build !CONFIG_PCI.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-09-10 16:00:09 -05:00
Paul Mackerras 35438c4327 Merge branch 'linux-2.6' into for-2.6.24 2007-08-28 15:56:11 +10:00
Kumar Gala ed16c20da6 [POWERPC] Remove old includes from arch/ppc
Remove includes of files that existed in arch/ppc that we dont need in
arch/powerpc anymore.  The following includes were removed:

 <asm/amigappc.h>
 <asm/bootinfo.h>
 <asm/ppcboot.h>
 <asm/ppc_sys.h>
 <asm/residual.h>
 <asm/m8260_pci.h>

This also caused platforms/embedded6xx/mpc7448_hpc2.h to no longer be
needed and thus removed.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-08-22 22:39:35 -05:00
Kumar Gala b66510cb99 [POWERPC] Fix interrupt routing and setup of ULI M1575 on FSL boards
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function.  Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:

PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15

Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.

Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.

Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-08-17 13:22:16 -05:00
Kim Phillips 3c5ede8cc6 [POWERPC] Revert "[POWERPC] Add 'mdio' to bus scan id list for platforms with QE UEC"
This reverts commit 3baee95595.

That commit was a mistake from the start; I added mdio type to the
bus scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).

This follows on from commit 77926826f301fbd8ed96d3cd9ff17a5b59560dfb:

 Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"

which was basically trying to hide a symptom of the original mistake
this revert fixes.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-08-10 21:04:22 +10:00
Randy Vinson 8d7bc8f9d1 [POWERPC] 85xxCDS: Misc 8548 PCI Corrections.
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.

Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-24 10:31:49 -05:00
Randy Vinson bca03c6bdd [POWERPC] 85xxCDS: Delay 8259 cascade hookup.
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.

Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-24 10:31:34 -05:00
Randy Vinson 637e9e13a1 [POWERPC] 85xxCDS: Make sure restart resets the PCI bus.
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.

Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 22:35:12 -05:00
Randy Vinson 3620fc1da2 [POWERPC] 85xxCDS: Allow 8259 cascade to share an MPIC interrupt line.
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.

NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.

Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 22:34:40 -05:00
Roy Zang f16dab981a [POWERPC] Add basic PCI/PCI Express support for 8544DS board
Add basic support for the PCIe PHB and enable the ULI bridge.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 22:30:02 -05:00
Kumar Gala 2e56ff206b [POWERPC] Make endianess of cfg_addr for indirect pci ops runtime
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian.  This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 22:29:09 -05:00
Kumar Gala 4e7982115e [POWERPC] 85xx: Add quirk to ignore bogus FPGA on CDS
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device.  Add a quirk to just ignore the
FPGA.

This is based on the following patch from Andy & York:

http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 10:27:08 -05:00
Kumar Gala aa3c112146 [POWERPC] 85xx: Added 8568 PCIe support
Added the PCIe device node to the 8568 dts and the needed quirk entries.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 10:27:08 -05:00
Kumar Gala 6c0a11c118 [POWERPC] Fixup resources on pci_bus for PCIe PHB when no device is connected
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 10:27:08 -05:00
Roy Zang 3f6c5dae27 [POWERPC] Use Freescale pci/pcie common code for 85xx boards
Switch the 85xx platform over to using the FSL generic PCI code.  This
gets ups PCIe support in addition to base PCI support.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-23 10:27:08 -05:00
Roy Zang 749e80810d [POWERPC] Remove redundant pci_read_irq_line() function for 85xx platform
Remove redundant pci_read_irq_line() function for 85xx CDS board.
This function has been realized in common ppc pci code.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-09 23:24:50 -05:00
Kumar Gala b533f8ae79 [POWERPC] Reworked interrupt numbers for OpenPIC based Freescale chips
Make the interrupt numbers match the OpenPIC spec intead of the
Freescale docs which distinguish between internal and external interrupts.

Now we can use the interrupt number directly to find the register offset
associated with it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-03 02:35:35 -05:00
Roy Zang 68fb0d203f [POWERPC] 85xx: Fix 8548CDS reset bug
Begin with MPC8548 a new reset control register is added that asserts
HRESET_REQ to board logic.

This register is used for chip reset.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-07-03 02:04:29 -05:00
Kumar Gala dbf8471f52 [POWERPC] Merge ppc32 and ppc64 pcibios_alloc_controller() prototypes
Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-29 01:58:39 -05:00
Kumar Gala 0a3786c5f7 [POWERPC] Removed remnants of bus_offset
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.

83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-29 01:58:15 -05:00
Kumar Gala 5229ee1852 [POWERPC] Remove hack to determine the 2nd PHBs bus number
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not.  The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-29 01:57:29 -05:00
Kumar Gala 7d52c7b0cd [POWERPC] Pass the pci_controller into pci_exclude_device
There are times that we need to know which controller we are on to decide
how to exclude devices properly.  We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-29 01:57:22 -05:00
Kumar Gala 5ab9c4524d [POWERPC] Remove set_cfg_type for PCI indirect users that don't need it
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles.  They handle producing them by implicitly looking at the
bus, devfn.

The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-06-29 01:57:07 -05:00
Arnd Bergmann 3dfaa762b5 [POWERPC] kill isa_{io,mem}_base definitions for !PCI
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.

The easiest fix is to just remove all these definitions.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2007-06-29 01:56:43 -05:00
Arnd Bergmann 09b55f76c9 [POWERPC] rename add_bridge to avoid namespace clashes
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2007-06-29 01:56:23 -05:00
Stephen Rothwell 55b61fec22 [POWERPC] Rename device_is_compatible to of_device_is_compatible
for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-07 20:31:14 +10:00
Kim Phillips 3baee95595 [POWERPC] Add 'mdio' to bus scan id list for platforms with QE UEC
Add 'mdio' to bus scan id list for platforms with QE UEC
as a consequence of converting UEC mdio driver to an
of_platform driver in the ucc_geth phylib conversion patch.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-02 20:04:29 +10:00
Paul Mackerras 445c9b5507 Merge branch 'kconfig' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.22 2007-04-24 08:42:11 +10:00
Kumar Gala db9478086d [POWERPC] Convert 85xx platform to unified platform Kconfig
Moved 85xx platform Kconfig over to being sourced by the unified
arch/powerpc/platforms/Kconfig.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-04-12 17:44:07 -05:00
Stephen Rothwell e2eb63927b [POWERPC] Rename get_property to of_get_property: arch/powerpc
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-13 03:55:19 +10:00
Paul Mackerras e049d1ca30 Merge branch 'linux-2.6' into for-2.6.22 2007-04-13 03:50:03 +10:00
Jon Loeliger d93daf8481 [POWERPC] 85xx: Add initial MPC8544 DS platform files.
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.

Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-03-29 19:39:27 -05:00
Kumar Gala f194bda4ce [POWERPC] 85xx: Enable CONFIG_SERIAL_8250_SHARE_IRQ
On chip 8250 UARTs share an interrupts on existing 85xx processors.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-03-07 23:14:57 -06:00
Kumar Gala 23f510bcd3 [POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards
Renamed the MPC8568 MDS platform code to follow other 85xx boards.  There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-17 16:29:36 -06:00
Kumar Gala 6936c62571 [POWERPC] 85xx: Cleaning up machine probing
Cleaned up the probing functionality to be more consistent across all 85xx
boards and actually check to see if we should be running on a given board.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-17 16:19:34 -06:00
Jon Loeliger 578f8f20f3 [POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-16 18:14:08 -06:00
Andy Fleming c2882bb12c [POWERPC] 85xx: Add support for the 8568 MDS board
Add support for the MPC8568 MDS reference board

Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-13 12:36:23 -06:00
Kumar Gala 27630bec94 [POWERPC] 85xx: Marked functions static
Marked a number of functions in 85xx board code as static.  Also, some minor
whitespace cleanup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-09 09:30:45 -06:00
Benjamin Herrenschmidt 3d1ea8e8cb [POWERPC] Remove ioremap64 and fixup_bigphys_addr
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.

This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.

This is a preliminary work for the upcoming merge of 32 and 64 bits io.h

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:39:04 +11:00
Benjamin Herrenschmidt f90bb153b1 [POWERPC] Make pci_read_irq_line the default
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.

It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().

It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.

I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.

I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 16:00:04 +11:00
Olaf Hering 35a84c2f56 [POWERPC] Fix up after irq changes
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-07 22:08:26 +10:00
Olof Johansson 49f19ce401 [PATCH] powerpc: irq change build breaks
Fix up some of the buildbreaks from the irq handler changes.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-05 18:39:04 -07:00
Dave Jones 038b0a6d8d Remove all inclusions of <linux/config.h>
kbuild explicitly includes this at build time.

Signed-off-by: Dave Jones <davej@redhat.com>
2006-10-04 03:38:54 -04:00
Uwe Zeisberger f30c226954 fix file specification in comments
Many files include the filename at the beginning, serveral used a wrong one.

Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 23:01:26 +02:00
Vitaly Bordug d3465c921f POWERPC: overhaul with cpm2_map mechanism
Incorporating the new way of cpm2 immr access, introduced in the previous
patch, into CPM2 peripheral devices (fs_enet and cpm_uart). Both ppc and
powerpc approved working( real actions taken in powerpc only, ppc just
has a wrapper to keep init stuff consistent).

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
2006-09-21 22:38:05 +04:00
Vitaly Bordug 902f392d01 POWERPC: Add support for the mpc8560 eval board
This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.

Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).

This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
2006-09-21 22:31:26 +04:00
Paul Mackerras ea0763a7e6 Merge branch 'merge' 2006-08-25 14:56:07 +10:00
Andy Fleming ddd64159eb [POWERPC] Fix CDS IRQ handling and PCI code
* Fix IRQ support in the 85xx CDS boards so it uses the new
  generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot.  This will be
  fixed soon, but the current code doesn't even compile, so this
  is a vast improvement

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-08-23 15:51:18 +10:00
Andy Fleming 4c86cd9c59 [POWERPC] Fix interrupts on 8540 ADS board
* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
  and sense values

Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-08-23 15:51:18 +10:00
Jeremy Kerr 8efca49329 [POWERPC] mpc: Constify & voidify get_property()
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.

mpc* platform changes.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-07-31 15:55:04 +10:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Greg Kroah-Hartman 685143ac1f [PATCH] 64bit resource: fix up printks for resources in arch and core code
This is needed if we wish to change the size of the resource structures.

Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com> and
Andrew Morton.

(tweaked by Andy Isaacson <adi@hexapodia.org>)

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-27 09:23:59 -07:00
Andy Fleming 591f0a4287 Add 85xx CDS to arch/powerpc
This patch adds support for 85xx CDS support to arch/powerpc

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2006-04-04 16:09:18 -05:00
Kumar Gala 72d2c3e038 powerpc: converted embedded platforms to use new define_machine support
Removed platform_init usage on 83xx and 85xx and use define_machine and
probe().  For now we always return true in the problem since you can only
build for one specific board at a time.  This is an artificial constraint.
When we get ride of it we will need to update the Kconfig's for these
sub-arch's and make the board's probe() functions actually do something.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2006-03-30 23:39:57 -06:00
Kumar Gala 9cf8ca3871 powerpc: Make uImage default build output for MPC8540 ADS
When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2006-03-27 23:44:37 -06:00
Andy Fleming 8080d54971 powerpc: Add PCI support for 8540 ADS to powerpc tree
Add PCI support for setting PCI from flat device tree on 85xx specifically for
MPC8540 ADS.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2006-02-21 23:48:59 -06:00
Becky Bruce fbc94e7c3d [PATCH] powerpc: lindent 85xx platform code
Ran arch/powerpc/platforms/85xx through Lindent

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-02-10 16:51:57 +11:00
Becky Bruce e19217d42e [PATCH] powerpc: rename mpc85xx.c to misc.c
Rename mpc85xx.c to misc.c to match the pattern established by the
8349 port - consistency is a good thing.  Also run Lindent on the
file to clean it up.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-02-10 16:51:56 +11:00
Becky Bruce 46ed55f647 [PATCH] powerpc: mpc85xx_ads.c include file cleanup
Cut-and-paste from the old platform code in arch/ppc resulted in
arch/powerpc/platforms/85xx/mpc85xx_ads.c having way too many
header files included.  Clean this up.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-02-10 16:51:53 +11:00
Becky Bruce 63dafe5728 [PATCH] powerpc: Updated Initial MPC8540 ADS port with OF Flat Dev
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-20 16:11:06 +11:00
Paul Mackerras fd582ec88e ppc: Various minor compile fixes
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.

This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-11 22:08:12 +10:00
Paul Mackerras 14cf11af6c powerpc: Merge enough to start building in arch/powerpc.
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files.  It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac.  This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.

For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel.  This makes some minor changes
to files in those directories and files outside arch/powerpc.

The boot directory is still not merged.  That's going to be interesting.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-09-26 16:04:21 +10:00