Currently the link event flow works, but can be much better.
Refactor the link event flow to make it cleaner and more clear
on what is going on.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY type ICE_PHY_TYPE_LOW_25G_AUI_C2C is missing from
ice_get_settings_link_up() which is causing a warning
message for unrecognized PHY. Add the PHY type to
correctly set the settings and avoid the warning message.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:
vsi->hw_base_vector + q_vector->v_idx
This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Runtime change of PFINT_OICR_ENA register is unnecessary.
The handlers should always clear the atomic bit for each
task as they start, because it will make sure that any late
interrupt will either 1) re-set the bit, or 2) be handled
directly in the "already running" task handler.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issue with non trusted VFs being able to add more than
permitted number of VLANs by adding a check in ice_vc_process_vlan_msg.
Also don't return an error in this case as the VF does not need to know
that it is not trusted.
Also rework ice_vsi_kill_vlan to use the right types.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_ctrl_rx_rings() we are unnecessarily waiting for
QRX_CTRL_QENA_REQ and QRX_CTRL_QENA_STAT to be the same value prior to
disabling each Rx queue. There is no reason to do this so remove
this wait loop as we already have a wait loop after disabling/enabling
the Rx queue through the QRX_CTRL register to make sure it gets
successfully disabled/enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver allows rx-usecs-high values to be set,
but when querying the device for rx-usecs-high the value
does not stick. This is because it was not yet implemented.
Add code to allow the user to change rx-usecs-high and
use this to set the q_vector's intrl value.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to set 52 byte RSS hash key.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many places in the code where we do the following:
for (i = 0; i < vsi->num_q_vectors; i++)
Instead use the macro mentioned in the commit title:
ice_for_each_q_vector(vsi, i)
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stopping Tx rings, we use 'i' as an ring array index for looking up
whether the ice_ring exists and have assigned a q_vector. This checks
rings only within a given TC and we need to go through every ring in
VSI. Use 'q_idx' instead.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce scope of the variable 'err' to inside the for loop instead
of using it as a second looping conditional. Also while here,
improve the debug message if we fail to configure a Rx queue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis points out the default case in the switch statement in
ice_get_itr_intrl_gran() is an infeasible condition causing the default
case statement to be unreachable. Remove it and since the function no
longer returns anything but success, change it to just return void and
update the only call to it accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If there is no queue to disable, return appropriate configuration error
earlier without acquiring the lock.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a framework to store queue specific information
in VSI queue contexts. Currently VSI queue context (represented by
struct ice_q_ctx) only has q_handle as a member. In future patches,
this structure will be updated to hold queue specific information.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes: f121e0ea95 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The check of legal vport is to ensure the vport number falls between
0 and total number of vports. Along with the introduction of uplink
rep, enabled vports are not consecutive any more.
Therefore, rely on the eswitch vport getter function to check if it's
a valid vport.
As the getter function relies on eswitch, add the check of vport
group manager and validation the presence of eswitch structure.
Remove the redundant check in the function calls.
Since the vport array will be allocated once eswitch is initialized
and will be kept alive if eswitch presents, no need to protect it with
the state lock.
Fixes: 5ae5162066 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some functions issue vport commands and access vport array using
vport_index/vport_num interchangeably which is OK for VFs vports.
However, this creates potential bug if those vports are not VFs
(E.g, uplink, sf) where their vport_index don't equal to vport_num.
Prepare code to access mlx5_vport structure using a getter function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Several functions need to access mlx5_vport and vport_num.
When these functions are called, caller already has mlx5_vport*
available.
Hence pass such mlx5_vport pointer.
This is preparation patch to add error checks to
mlx5_eswitch_get_vport() and to return error status.
By doing so, reduce places where error check of mlx5_eswitch_get_vport()
can be avoided.
While doing such change, mlx5_eswitch_query_vport_drop_stats() gets
corrected to work on vport, instead of vport_idx.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5_esw_for_each_vf_vport iterates over mlx5_vport entries in
eswitch.c
Same macro in eswitch_offloads.c iterates over vport number in
eswitch_offloads.c
Instead of duplicate macro names, to avoid confusion and to reuse the
same macro in both files, move it to eswitch.h.
To iterate over vport numbers where there is no need to iterate over
mlx5_vport, but only a vport number is needed, rename those macros in
eswitch_offloads.c to mlx5_esw_for_each_vf_num_vport*.
While at it, keep all vport and vport rep iterators together.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CFLAGS_tracepoint.o specifies CFLAGS for compiling tracepoint.c but
it does not exist under drivers/net/ethernet/mellanox/mlx5/core/.
CFLAGS_tracepoint.o is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The same code that returns XDP frames and releases pages is used both in
mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs. Create a function that
cleans up an MPWQE.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With unlocked TC it is possible to have spurious deletes and inserts of
same filter. TC layer needs drivers to always return error when flow
insertion failed in order to correctly calculate "in_hw_count" for each
filter. Fix mlx5e_configure_flower() to return -EEXIST when TC tries to
insert a filter that is already provisioned to the driver.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets are
tagged with VLAN ID 0x000 (priority tag) and pop/push actions are
replaced by VLAN re-write actions (which are supported by the HW).
Replace TC VLAN pop action with a VLAN priority tag header rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. As a workaround, untagged packets are tagged with
VID 0x000 allowing pop/push actions to be exchanged with VLAN rewrite
actions.
Use the ingress ACL table, preceding the FDB, to push VLAN 0x000 ID tag
for untagged packets and the egress ACL table, succeeding the FDB, to
pop VLAN 0x000 ID tag.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Hardware requires that all TIRs that steer traffic to the same RQ
should share identical tunneled_offload_en value.
For that, the tunneled_offload_en bit should be set/unset (according to
the HW capability) for all TIRs', not only the ones dedicated for
tunneled (inner) traffic.
Fixes: 1b223dd391 ("net/mlx5e: Fix checksum handling for non-stripped vlan packets")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Many TIR context settings are common to different TIR types,
take them into a common function.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This commit introduces support for the "Drop" action in classification
offload. This corresponds to the "-1" action with ethtool -N.
This is achieved using the color marking actions available in the C2
engine, which associate a color to a packet. These colors can be either
Green, Yellow or Red, Red meaning that the packet should be dropped.
Green and Yellow colors are interpreted by the Policer, which isn't
supported yet.
This method of dropping using the Classifier is different than the
already existing early-drop features, such as VLAN filtering and MAC
UC/MC filtering, which are performed during the Parsing step, and
therefore take precedence over classification actions.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces basic classification offloading support for the
PPv2 controller.
The PPv2 classifier has many classification engines, for now we only use
the C2 TCAM match engine.
This engine allows to perform ternary lookups on 64 bits keys (called
Header Extracted Key), that are built by extracting fields from the packet
header and concatenating them. At most 4 fields can be extracted for a
single lookup.
This basic implementation allows to build the HEK from the following
fields :
- L4 source and destination ports (for UDP and TCP)
More fields are to be added in the future.
Classification flows are added through the ethtool interface, using the
newly introduced flow_rule infrastructure as an internal rule
representation, allowing to more easily implement tc flower rules if
need be.
The internal design for now allocates one range of 4 rules per port
due to the internal design of the flow table, which uses 22 sub-flows.
When inserting a classification rule, the rule is created in every
relevant sub-flow.
This low rule-count is a very simple design which reaches quickly the
limitations of the flow table ordering, but guarantees that the rule
ordering will always be respected.
This commit only introduces support for the "steer to rxq" action.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today, the classification code is used only for RSS. We split the
incoming traffic into multiple flows, that correspond to the ethtool
flow_type parameter.
We don't want to use the ethtool flow definitions such as TCP_V4_FLOW,
for several reason :
- We want to decorrelate the driver code from ethtool as much as
possible, so that we can easily use other interfaces such as tc flower,
- We want the flow_type to be a bitfield, so that we can match flows
embedded into each other, such as TCP4 which is a subset of IP4.
This commit does the conversion to the newer type.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch removing extra whitespaces when writing the flow_table
entries
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usleep_range() to avoid problems with msleep() actually sleeping
much longer than expected.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are actually using a BD for both the skb and each frag contained in
it, the oldest TX BD would be overwritten when there was exactly one BD
less than needed.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap the actual buffer length, not the amount of data received, avoiding
resource exhaustion of swiotlb (seen on x86_64 platform).
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With little-endian and 64-bit support in place, the ll_temac driver can
now be used on x86 and x86_64 platforms.
And while at it, enable COMPILE_TEST also.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.
Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.
This issue was detected with the help of Coccinelle.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* share more code across drivers
* new driver for MT7615 chipsets
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlzJfSQACgkQ130UHQKnbvUqiACfeNJFtx6+0CbEvDXDGKJ7a7Mx
w28An1uKNBgAKSbNoWny3ZFbOoHuApq9
=i9U/
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2019-05-01' of https://github.com/nbd168/wireless
mt76 patches for 5.2
* share more code across drivers
* new driver for MT7615 chipsets
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Replace "pass through" with a proper "fall through" annotation
in order to fix the following warning:
drivers/net/netdevsim/bus.c: In function ‘new_device_store’:
drivers/net/netdevsim/bus.c:170:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_count = 1;
~~~~~~~~~~~^~~
drivers/net/netdevsim/bus.c:172:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This fix is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally firmware messages are printed with debugging enabled only. It's
a good idea as firmware may print a lot of messages that normal users
don't need to care about.
However, on firmware crash, it may be very helpful to log all recent
messages. There is almost always a backtrace available as well as rought
info on the latest actions/state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some PCIE firmwares drop txstatus if pktid is 0 and make packet held in
host side and never be released. If that packet type is 802.1x, the
pend_8021x_cnt value will be always greater than 0 and show "Timed out
waiting for no pending 802.1x packets" error message when sending key to
dongle every time.
To be compatible with all firmwares, host should set txflow request id
from 1 instead of from 0.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
case MC_CMD_FCNTL_OFF:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).
Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo in msi code. No much impact though.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve for better readability
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we define and request an extra interrupt line,
assign it on link isr handler and restructure abit aq_pci code
to better support that.
We also remove logic for using different timer intervals
depending on link state, since thats now useless.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need this to schedule link interrupt handling and
various service tasks.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define link interrupt handler
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for hwmon api to fetch out chip temperature
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allocate mcu requests on the stack in mt7603_mcu_set_eeprom
in order to avoid the following warning:
Warning: the frame size of 1032 bytes is larger than 1024 bytes
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not enable/disable pre_tbtt_tasklet tasklet in
mt76x02_sw_scan/mt76x02_sw_scan_complete since it is already done
setting the operating channel. Do run tbtt_tasklet while the device is
offchannel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable pre_tbtt_tasklet tasklet before setting the operating channel.
Enable/disable beacon_timer in mt7603_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Announce antenna pattern cap to adapt PHY and baseband settings.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If buffer size is not usb_endpoint_maxp (512 or 1024 bytes) multiple,
usb host driver has to use bounce buffer and copy data. For RX we can
avoid that since we alreay allocate q->buf_size (2kB) buffers and
mt76usb hardware will not fill more data as rx packet size is limited
by network protocol. However add error message if this assumption
somehow will be not true.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Print fw_ver and build_date members of struct mt7603_fw_trailer
similarly to what appears in the output of 'dmesg' when the MCU firmware
is loaded.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix many warnings with incorrect endian assumptions.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: ec7d2d74760a ("mt76: mt76x02: use napi polling for tx cleanup")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run __mt76_mcu_send_msg instead of __mt7603_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use common function wrapper in mt7603_mcu_exit since the code is shared
with mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use __mt76_mcu_send_msg wrapper instead of mt7603_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 common signature for mt7603_mcu_msg_send. Move skb allocation
in mt7603_mcu_msg_send and remove duplicated code. This is a preliminary
patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove query parameter from mt7603_mcu_msg_send/__mt7603_mcu_msg_send
routine signature since it can be obtained from cmd value. This is a
preliminary patch for mcu code unification between mt7615 and mt7603
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous version only accidentally disabled A-MSDU deaggregation by
using the wrong mask for rx length configuration, which left previous
length value in place.
Fix the length and initialize the register completely to keep A-MSDU
de-aggregation remaining disabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 .start(), .stop() callbacks are never called concurrently with
other callbacks. The only concurencly is with mt76 works which we cancel
on stop() and schedule on start().
This fixes possible deadlock on cancel_delayed_work_sync(&dev->mac_work)
as mac_work also take mutex.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On suspend mac80211 .stop callback is called before .suspend(), so
hw mac is already stopped and we do not have to do this again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use macro to convert sn and seq_ctrl for better readability.
Signed-off-by: Roy Luo <royluo@google.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the tx/rx fastpath, the funciton dma_map_single() rarely fails.
This adds unlikely() optimization to this error check conditional.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This driver is for a newer generation of MediaTek MT7615 4x4 802.11ac
PCIe-based chipsets, which support wave2 MU-MIMO up to 4 users/group
and also support up to 160MHz bandwidth.
The driver fully supports AP, station and monitor mode.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Roy Luo <royluo@google.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce skb check for dummy address in mt76_dma_tx_cleanup_idx.
This is a preliminary patch to add support for new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce skb field in mt76_txwi_cache. Moreover add txwi_flags
to mt76_driver_ops since new chipsets will release mt76_txwi_cache/skbs
at tx completion instead of dma one.
This is a preliminary patch to add mt7615 support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Pass skb pointer to tx_prepare_skb through mt76_tx_info data structure.
This is a preliminary patch to properly support dma error path for
new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dynamically allocate txwi since new chipsets will use longer txwi
descriptors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to pci counterpart, reduce locking in mt76u_tx_tasklet since
q->head is managed just in mt76u_tx_tasklet and q->queued is updated
holding q->lock
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Brett Creeley