The system crashes during probing xgene-hwmon driver when temperature
alarm interrupt occurs before.
It's because
- xgene_hwmon_probe() requests mailbox channel which also enables
the mailbox interrupt.
- As temperature alarm interrupt is pending, ISR runs and crashes when
accesses into invalid resourse as unmapped PCC shared memory.
This patch fixes this issue by saving this alarm message and scheduling a
bottom handler after xgene_hwmon_probe() finish.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
iio_channel_get_all returns -ENODEV when it cannot find either phandles and
properties in the Device Tree or channels whose consumer_dev_name matches
iio_hwmon in iio_map_list. The iio_map_list is filled in by iio drivers
which might be probed after iio_hwmon.
It is better to defer the probe of iio_hwmon if such error is returned by
iio_channel_get_all in order to let a chance to iio drivers to expose
channels in iio_map_list.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The fan can be stopped by writing "3" to pwm1_enable in sysfs.
Add devicetree property for early initialization of the fan controller
to prevent overheating, for example when resetting the board while the
fan was completely turned off.
Also improve error reporting, I2C failures were ignored while writing
new values.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Parse devicetree parameters for voltage and prescaler setting. This allows
using multiple max6550 devices with varying settings, and also makes it
possible to instantiate and configure the device using devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the index comments at the end of it87_attributes_in. They
serve no purpose (as there is no reference to them in
it87_in_is_visible) and some of them were obviously wrong.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The UCD90160 Power Supply Sequencer reuses the existing register layout,
so just an id addition was required.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
[groeck: Updated description, ordered alphabetically, added documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If both hwmon and thermal_sys are built as modules, and
CONFIG_THERMAL_HWMON is enabled, the following cyclic module dependency
is reported.
depmod: ERROR: Found 2 modules in dependency cycles!
depmod: ERROR: Cycle detected: hwmon -> thermal_sys -> hwmon
Fixes: e4bce763adb2 ("hwmon: (core) New hwmon registration API")
Reported-by: Vignesh R <vigneshr@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7470 supports a variety of PWM frequencies. This patch allows the
frequency to be configured and viewed through the sysfs entry pwm1_freq.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow to specify the resistance of the attached shunt via DT by
adding the shunt-resistor property. Fall-back to the previous
default (1 mOhm) if unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[groeck: Fixed 'line over 80 columns' checkpatch warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit 698a7c24a5 ("hwmon: (nct6775) Support two SuperIO chips
in the same system"), the driver supports two Super-IO chips. This has
the undesirable side effect that force_id always detects a second chip
at address 0xfff8, even if no chip exists at that address.
nct6775: Found NCT6793D or compatible chip at 0x4e:0xfff8
If no chip at all is found at a given SIO address, it does not make sense
to instantiate it. Limit force_id to only work if some chip is found,
that is if the chip ID returns a value other than 0xffff.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic pwm attribute support (no auto attributes) to new API.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Up to now, each hwmon driver has to implement its own sysfs attributes.
This requires a lot of template code, and distracts from the driver's core
function to read and write chip registers.
To be able to reduce driver complexity, move sensor attribute handling
and thermal zone registration into hwmon core. By using the new API,
driver code and data size is typically reduced by 20-70%, depending
on driver complexity and the number of sysfs attributes supported.
With this patch, the new API only supports thermal sensors. Support for
other sensor types will be added with subsequent patches.
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ordering include files alphabetically makes it easier to add new ones.
Stop including linux/spinlock.h and linux/kdev_t.h since both are not
needed.
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of repeatedly accessing &pdev->dev, use a local variable dev
instead where possible. Also drop 'dev' from private data since it is
unnecessary.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provide support for PSU DPS-460, DPS-800 from Delta Electronics, INC
and for SGD009 from Acbel Polytech, INC.
These devices do not support the STATUS_CML register, and reports a
communication error in response to this command. For this reason,
the status register check is disabled for these controllers.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the EXT_TDM bit is set, the chip supports a second temperature sensor
instead of two voltage sensors.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lower temperature limit is -128 degrees C. The supported upper limits
are 127.875 or 255.875 degrees C. Also, don't fail if a value outside
the supported range is provided when setting a temperature limit.
Instead, clamp the provided value to the available value range.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing the update_interval attribute could result in an overflow if
a number close to the maximum unsigned long was written. At the same
time, even though the chip supports setting the conversion rate,
the selected conversion rate was not actually written to the chip.
Fix the second problem by selecting valid (supported) conversion rates,
and writing the selected conversion rate to the chip. This also fixes the
first problem, since arbitrary conversion rates are now converted to
actually supported conversion rates.
Also, set the default chip conversion rate to 1 second. Previously, the
chip was configured for continuous conversion, but readings were only
retrieved every seond, which doesn't make much sense. If we only read a
value from the chip every second, we can as well save some power and only
convert in one-second intervals.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.
Fixes: 5292971563 ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Coverity reports:
result_independent_of_operands: data->features & (65536UL /* 1UL << 16 */)
is always 0 regardless of the values of its operands. This occurs as the
logical operand of if.
data->features needs to be 32 bit wide since there are more than 16 features.
Fixes: cc18da79d9 ("hwmon: (it87) Support up to 6 temperature sensors ... ");
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the datasheet we have to set some bits as 0 and others as 1.
Make sure we do this for CFG1 and CFG3.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "name" variable's memory is now freed when the device is destructed
thanks to devm function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: e0f8a24e0e ("staging:iio::hwmon interface client driver.")
Fixes: 61bb53bcbd ("hwmon: (iio_hwmon) Add support for humidity sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using set_bit() to set a bit in an integer is not a good idea, since
the function expects an unsigned long as argument, which can be 64 bit
wide. Coverity reports this problem as
>>> CID 1364488: Memory - illegal accesses (INCOMPATIBLE_CAST)
>>> Pointer "&ret" points to an object whose effective type is "int"
>>> (32 bits, signed) but is dereferenced as a wider "unsigned
+long" (64 bits, unsigned). This may lead to memory corruption.
245 set_bit(1, (unsigned long *)&ret);
Just use BIT instead.
Cc: Thilo Cestonaro <thilo@cestona.ro>
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace devm_add_action() with devm_add_action_or_reset(),
and check its return value.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handling the wraparound requires the data->last_update to be set to an
initial jiffies value. Otherwise on 32-bit systems you will not be able
to request a reading till the 5 minute jiffies rollover happens.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David Frey <david.frey@sensirion.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 7c84f7f80d ("hwmon: add support for Sensirion SHT3x sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345 ("hwmon: Add driver for ADT7411 voltage and temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver implements hardware monitoring and watchdog support
for the FTS BMC Chip "Teutates".
Signed-off-by: Thilo Cestonaro <thilo@cestona.ro>
[groeck: Updated subject and description; fixed dependencies]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The enables control of the SHT31 sensors heating element that can turned
on to remove excess humidity.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David Frey <david.frey@sensirion.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With this change, JC-42.4 compatible temperature sensors can be configured
in devicetree by providing a generic "jedec,jc-42.4-temp" binding.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By converting the driver to regmap, we can use regmap to cache non-volatile
registers. Stop caching the temperature register; while potentially reading
it more often can result in reading it more often than necessary, this is
offset by the gain due to not re-reading the limit registers.
A positive side effect of this change is that limit registers can now be
read and updated before the first temperature conversion is complete.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the chip was forced into polarity 0, even if it was preconfigured
differently. Do not touch the polarity when configuring the chip.
Also, the configuration register was read beack to check if the
configuration 'sticks'. Ultimately, that is similar to checking if the
chip is a tmp102 in the first place. Checking if a write into the
configuration register was successful is really not the way to do it,
and quite risky if the chip is not a tmp102, so drop that check.
Instead, verify if the configuration register has unexpected bits set
before writing into it.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the chip was in shutdown mode when the driver was loaded, the first
conversion is ready no more than 35 milli-seconds after the chip was
taken out of shutdown. The driver delay was so far set to 333 ms (HZ / 3),
which is much higher than the maximum time needed by the chip.
Reduce the time to 35 milli-seconds.
Introduce a 'valid' flag to ensure that sensor data is actually read
even if requested less than 333 ms after the driver was loaded.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Return both error code and register value as return code from
read functions, and always check for errors.
This reduces code size on x86_64 by more than 1k while at
the same time improving error resiliency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since all other cleanup handled with devm_add_action, we can use
devm_hwmon_device_register_with_groups() to register the hwmon
device, and drop the remove function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use regmap. Leave caching to regmap and drop the register
update function. While this can result in additional read operations
if the temperature register is read continuously, it avoids re-reading
the limit registers and thus overall reduces complexity.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
lm75_read_value and lm75_write_value don't really add any value.
Replace with direct smbus access functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_add_action() to register the function to restore the original
chip configuration. Use devm_hwmon_device_register_with_groups()
to register the hwmon device, and drop the remove function as no
longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In 2011, commit 774466add7 ("hwmon: (jc42) Change detection class")
changed the detection class of these chips to I2C_CLASS_SPD based
on this premise: "makes more sense because these chips always live on
memory modules"
Today these chips have applications beyond memory modules. Examples are
JC42.4 compatible chips such as MCP9804 and MCP9808, but also MCP9805,
which is marked as JC42.4 compliant and suggested for use not only for
DIMMS, but also as generic temperature sensor.
Add I2C_CLASS_HWMON as an additional detection class to allow detection
by hwmon class i2c adapters.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By registering a cleanup function with devm_add_action(), we can
simplify the error path in the probe function and drop the remove
function entirely.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MCP9808 is not officially compliant to JC-42, similar to MCP9804,
but its registers are compatible to JC-42.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The result of an integer divide by an unsigned is undefined.
This causes unexpected results when writing negative values
into the limit registers.
Maintain the shunt_resistors variables as signed integer to avoid
the problem. Also, for simplicity and ease of use, clamp shunt
resistor value on writes instead of rejecting bad values.
Cc: Andrew F. Davis <afd@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allow us to debug how long take each SMM call and how long is system
frozen in SMM handler.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines (e.g. Dell Precision M3800) have two fans, first with
index=0 and second with index=2. So export also attributes for third fan
device with index=2.
Reported-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
The update_lock mutex is not used, so remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the the INA3221 26v capable, Triple channel,
Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor
with I2C interface.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver implements support for the Sensirion SHT3x-DIS chip,
a humidity and temperature sensor. Temperature is measured
in degrees celsius, relative humidity is expressed as a percentage.
In the sysfs interface, all values are scaled by 1000,
i.e. the value for 31.5 degrees celsius is 31500.
Signed-off-by: Pascal Sachs <pascal.sachs@sensirion.com>
[groeck: Fixed 'Variable length array is used' gcc warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On more Dell machines (e.g. Dell Precision M3800) fan_type() call is too
expensive (CPU is too long in SMM mode) and cause kernel to hang. This is
bug in Dell SMM or BIOS.
This patch caches type for each fan (as it should not change) and changes
the way how fan presense is detected. First it try function fan_status()
as was before commit f989e55452 ("i8k: Add support for fan labels"). And
if that fails fallback to fan_type(). *_status() functions can fail in case
fan is not currently accessible (e.g. present on GPU which is currently
turned off).
Reported-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112021
Cc: stable@vger.kernel.org # v4.0+, will need backport
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines have especially broken SMM or BIOS which cause that once
fan_type() is called then CPU fan speed going randomly up and down. And for
fixing this behaviour reboot is required.
So this patch creates fan_type blacklist of affected Dell machines and
disallow fan_type() call on them to prevent that erratic behaviour.
Old blacklist which disabled loading driver on some machines added in
commits a4b45b25f1 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8100")
and 6220f4ebd7 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8000") were
moved to FAN_TYPE blacklist.
Reported-by: Jan C Peters <jcpeters89@gmail.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For security reasons ordinary user must not be able to control fan speed
via /proc/i8k by default. Some malicious software running under "nobody"
user could be able to turn fan off and cause HW problems. So this patch
changes default value of "restricted" parameter to 1.
Also restrict reading of DMI_PRODUCT_SERIAL from /proc/i8k via "restricted"
parameter. It is because non root user cannot read DMI_PRODUCT_SERIAL from
sysfs file /sys/class/dmi/id/product_serial.
Old non secure behaviour of file /proc/i8k can be achieved by loading this
module with "restricted" parameter set to 0.
Note that this patch has effects only for kernels compiled with CONFIG_I8K
and only for file /proc/i8k. Hwmon interface provided by this driver was
not changed and root access for setting fan speed was needed also before.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org # will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ABI of I8K_BIOS_VERSION ioctl can return only number. But new BIOS versions
contain also other characters, which does not fit into that ABI. So in case
of non digit values return -EINVAL.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.
This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code handles this variable always as unsigned, so adapt the type.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We need to read a bunch of registers on each compute unit and possibly
on the current CPU too. Disable preemption around it. Otherwise, you
get:
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/327
caller is read_registers+0x6a/0x110 [fam15h_power]
CPU: 3 PID: 327 Comm: systemd-udevd Not tainted 4.7.0-rc1+ #4
Hardware name: HP HP EliteBook 745 G3/807E, BIOS N73 Ver. 01.08 01/28/2016
...
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Rui Huang <ray.huang@amd.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Huang Rui <ray.huang@amd.com>
Tested-by: Huang Rui <ray.huang@amd.com>
Fixes: fa79434499 ("hwmon: (fam15h_power) Add compute unit accumulated power")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon fixlets from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation/hwmon: Update links in max34440
hwmon: (emc2103) Fix typo in MODULE_PARM_DESC
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
IT8628E is functionally identical to IT8620E.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the chips supported by this driver have a configuration
register to enable fan4 and fan5. Use those registers to determine
if fan4 and fan5 tachometers are supported.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On/Off mode is only supported for pwm controls 0-2, and not supported at all for
IT8603E/IT8623E. For pwm controls 3-6 and for IT8603E/IT8623E, SmartGuardian mode
is always enabled. Use it and set the pwm value to the maximum if fan control
is disabled.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix various checkpatch complaints to clean up the code and
make it easier to read.
CHECK: Do not include the paragraph about writing to the FSF
CHECK: Alignment should match open parenthesis
CHECK: Logical continuations should be on the previous line
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: spaces preferred around that '+' (ctx:VxV)
WARNING: Missing a blank line after declarations
No functional change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using array size defines makes it much easier to find errors
in index values and loop counts.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using the BIT macro makes the code a little easier to read and has the
added benefit of making checkpatch happy.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E supports three additional voltage sensors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Voltage registers are non-sequential. Use a register array instead
of a macro to map sensor index to register to simplify the code
and to make it easier to add additional voltage sensors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the additional temperature sensors on IT8620E.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_hwmon_device_register_with_groups to simplify
code and reduce code size. This also attaches sysfs attributes
to the hwmon device and no longer to the platform device.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use is_visible to determine if attributes should be generated or not.
This simplifies the code and reduces object size by about 120 bytes
on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce object size by about 250 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce object size by almost 500 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce object size by more than 200 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce object size by more than 300 bytes on x86_64.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Super-IO chip can also reside at SIO address 0x4e, and there can be
two Super-IO chips in the system. Add support for it.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This will let us support more than one chip on different SIO addresses
with the same driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using the same varible name for function names and as static
variable invites misuse and prevents us from adding support
for a second chip. Rename pdev to it87_pdev and limit its use
to where it is needed.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Return directly on errors if there is no cleanup necessary.
Don't create an error message on memory allocation errors.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent chips have a separate register to select the pwm2 frequency.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E supports up to 6 pwm channels. Add support for it.
Also check if fan tachometers 4..6 are enabled before instantiating
the respective sysfs attributes.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AVCC3 is supported on IT8620E, similar to IT8603E. Add feature flag
to indicate AVCC3 support. Don't enable it for now on IT8620E since
it is unclear if this chip supports it correctly.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds a platform check function to make code more readable.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds the description to explain the TDP reporting mechanism
and accumulated power algorithm.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch introduces an algorithm that computes the average power by
reading a delta value of “core power accumulator” register during
measurement interval, and then dividing delta value by the length of
the time interval.
User is able to use power1_average entry to measure the processor power
consumption and power1_average_interval entry to set the interval.
A simple example:
ray@hr-ub:~/tip$ sensors
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 19.58 mW (avg = 2.55 mW, interval = 0.01 s)
(crit = 15.00 W)
...
The result is current average processor power consumption in 10
millisecond. The unit of the result is uWatt.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PTSC is the performance timestamp counter value in a cpu core and the
cores in one compute unit have the fixed frequency. So it picks up the
performance timestamp counter value of the first core per compute unit
to measure the interval for average power per compute unit.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds a member in fam15h_power_data which specifies the
compute unit accumulated power. It adds do_read_registers_on_cu to do
all the read to all MSRs and run it on one of the online cores on each
compute unit with smp_call_function_many(). This behavior can decrease
IPI numbers.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds CONFIG_CPU_SUP_AMD as the dependence of fam15h_power
driver. Because the following patch will use the interface from
x86/kernel/cpu/amd.c.
Otherwise, the below error might be encountered:
All errors (new ones prefixed by >>):
drivers/built-in.o: In function `fam15h_power_probe':
>> fam15h_power.c:(.text+0x26e3a3): undefined reference to
>> `amd_get_cores_per_cu'
fam15h_power.c:(.text+0x26e41e): undefined reference to
`amd_get_cores_per_cu'
Reported-by: build test robot <lkp@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic support for the Maxim Integrated MAX31722/MAX31723 SPI
temperature sensors / thermostats.
Includes:
- ACPI support;
- raw temperature readings;
- power management
Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX31722-MAX31723.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.
Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
arm:pxa_defconfig can result in the following crash if the max1111 driver
is not instantiated.
Unhandled fault: page domain fault (0x01b) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 1b [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 300 Comm: kworker/0:1 Not tainted 4.5.0-01301-g1701f680407c #10
Hardware name: SHARP Akita
Workqueue: events sharpsl_charge_toggle
task: c390a000 ti: c391e000 task.ti: c391e000
PC is at max1111_read_channel+0x20/0x30
LR is at sharpsl_pm_pxa_read_max1111+0x2c/0x3c
pc : [<c03aaab0>] lr : [<c0024b50>] psr: 20000013
...
[<c03aaab0>] (max1111_read_channel) from [<c0024b50>]
(sharpsl_pm_pxa_read_max1111+0x2c/0x3c)
[<c0024b50>] (sharpsl_pm_pxa_read_max1111) from [<c00262e0>]
(spitzpm_read_devdata+0x5c/0xc4)
[<c00262e0>] (spitzpm_read_devdata) from [<c0024094>]
(sharpsl_check_battery_temp+0x78/0x110)
[<c0024094>] (sharpsl_check_battery_temp) from [<c0024f9c>]
(sharpsl_charge_toggle+0x48/0x110)
[<c0024f9c>] (sharpsl_charge_toggle) from [<c004429c>]
(process_one_work+0x14c/0x48c)
[<c004429c>] (process_one_work) from [<c0044618>] (worker_thread+0x3c/0x5d4)
[<c0044618>] (worker_thread) from [<c004a238>] (kthread+0xd0/0xec)
[<c004a238>] (kthread) from [<c000a670>] (ret_from_fork+0x14/0x24)
This can occur because the SPI controller driver (SPI_PXA2XX) is built as
module and thus not necessarily loaded. While building SPI_PXA2XX into the
kernel would make the problem disappear, it appears prudent to ensure that
the driver is instantiated before accessing its data structures.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.
The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1278 is mostly compatible to other chips of the same series.
Besides the usual difference in coefficients, it supports
a temperature sensor, and it can measure both input and output
voltage at the same time.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the Murata NCP15XH103 thermistor series.
Signed-off-by: Joseph McNally <jmcna06@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the driver calls hwmon_device_register_with_groups which
does not accept hypen in node name and returns EINVAL. Use of hypen
in device tree node name results in probe failure., however use of
hypen in device tree node name is perfectly acceptable.
Change this by allocating a duplicate managed string, replacing
hypen with underscore and then calling hwmon_device_register_with_groups.
This allows the use of hypen in device tree node name while maintaining
backwards compatibility and preventing any possible regressions with
user space.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds support for the Linear Technology LTC2990 I2C System Monitor.
The LTC2990 supports a combination of voltage, current and temperature
monitoring. This driver currently only supports reading two currents
by measuring two differential voltages across series resistors, in
addition to the Vcc supply voltage and internal temperature.
This is sufficient to support the Topic Miami SOM which uses this chip
to monitor the currents flowing into the FPGA and the CPU parts.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The vexpress hwmon implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in regulators.
This patch renames the vexpress hwmon implementation to vexpress-hwmon
so that there will be no clash in the module namespace.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
1. Minor fix to restore functionality in big-endian mode
2. Fix race by decreasing Tx timeout to 20ms
3. Adds support for 64-bit sensor values and energy meter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HnG3
-----END PGP SIGNATURE-----
Merge tag 'scpi-for-v4.6/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
SCPI updates and fixes for v4.6
1. Minor fix to restore functionality in big-endian mode
2. Fix race by decreasing Tx timeout to 20ms
3. Adds support for 64-bit sensor values and energy meter
* tag 'scpi-for-v4.6/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
Signed-off-by: Olof Johansson <olof@lixom.net>
Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).
When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.
Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.
Fixes: b5cf88e46b ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.
Signed-off-by: Peter Rosin <peda@axentia.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SCPI specification v1.1 adds support for energy sensors. This patch
adds support for the same.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCPI specification version 1.1 extended the sensor from 32-bit to 64-bit
values in order to accommodate new sensor class with 64-bit requirements
Since the SCPI driver sets the higher 32-bit for older protocol version
to zeros, there's no need to explicitly check the SCPI protocol version
and the backward compatibility is maintainted.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since Linux 4.0 the CPU fan speed is going up and down on Dell Studio
XPS 8000 and 8100 for unknown reasons. The 8100 was already
blacklisted in commit a4b45b25f1 ("hwmon: (dell-smm) Blacklist
Dell Studio XPS 8100"). This patch blacklists the XPS 8000.
Without further debugging on the affected machine, it is not possible
to find the problem. For more details see
https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Thorsten Leemhuis <linux@leemhuis.info>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull watchdog updates from Wim Van Sebroeck:
"This adds following items:
- watchdog restart handler support
- watchdog reboot notifier support
- watchdog sysfs attributes
- support for the following new devices: AMD Mullins platform, AMD
Carrizo platform, meson8b SoC, CSRatlas7, TS-4800, Alphascale
asm9260-wdt, Zodiac, Sigma Designs SMP86xx/SMP87xx
- Changes in refcounting for the watchdog core
- watchdog core improvements
- and small fixes"
* git://www.linux-watchdog.org/linux-watchdog: (60 commits)
watchdog: asm9260: remove __init and __exit annotations
watchdog: Drop pointer to watchdog device from struct watchdog_device
watchdog: ziirave: Use watchdog infrastructure to create sysfs attributes
watchdog: Add support for creating driver specific sysfs attributes
watchdog: kill unref/ref ops
watchdog: stmp3xxx: Remove unused variables
watchdog: add MT7621 watchdog support
hwmon: (sch56xx) Drop watchdog driver data reference count callbacks
watchdog: da9055_wdt: Drop reference counting
watchdog: da9052_wdt: Drop reference counting
watchdog: Separate and maintain variables based on variable lifetime
watchdog: diag288: Stop re-using watchdog core internal flags
watchdog: Create watchdog device in watchdog_dev.c
watchdog: qcom-wdt: Do not set 'dev' in struct watchdog_device
watchdog: mena21: Do not use device pointer from struct watchdog_device
watchdog: gpio: Do not use device pointer from struct watchdog_device
watchdog: tangox: Print info message using pointer to platform device
watchdog: bcm2835_wdt: Drop log message if watchdog is stopped
devicetree: watchdog: add binding for Sigma Designs SMP8642 watchdog
watchdog: add support for Sigma Designs SMP86xx/SMP87xx
...
Mitac microcode differs from Intel microcode. One key difference
is that pwm values can be written.
Detect vendor from customer ID field and no longer use DMI data
to identify which microcode is running on the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The aem_rw_sensor_template and aem_ro_sensor_template structures are never
modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reference counting is now implemented in the watchdog core and no longer
required in watchdog drivers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The sensor_template_group structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMD Family 15h Models 70h-7fh processors also support TDP power
reporting interface.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3815 is a Monolithic Synchronous DC/DC Step-Down Converter.
Cc: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
HTU21 is now supported by IIO, and can be instantiated as hwmon driver
using the iio-hwmon bridge. An explicit hwmon driver is no longer needed.
Cc: William Markezana <william.markezana@meas-spec.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_BITREVERSE is not built-in, the sht15 driver fails to link:
drivers/built-in.o: In function `sht15_crc8':
drivers/hwmon/sht15.c:195: undefined reference to `byte_rev_table'
This adds a Kconfig 'select' statement, like all other users of
bitrev.h have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33836ee985 ("hwmon:change sht15_reverse()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP102 works based on conversions done periodically. However, as per
the TMP102 data sheet[1] the first conversion is triggered immediately
after we program the configuration register. The temperature data
registers do not reflect proper data until the first conversion is
complete (in our case HZ/4).
The driver currently sets the last_update to be jiffies - HZ, just
after the configuration is complete. When TMP102 driver registers
with the thermal framework, it immediately tries to read the sensor
temperature data. This takes place even before the conversion on the
TMP102 is complete and results in an invalid temperature read.
Depending on the value read, this may cause thermal framework to
assume that a critical temperature event has occurred and attempts to
shutdown the system.
Instead of causing an invalid mid-conversion value to be read
erroneously, we mark the last_update to be in-line with the current
jiffies. This allows the tmp102_update_device function to skip update
until the required conversion time is complete. Further, we ensure to
return -EAGAIN result instead of returning spurious temperature (such
as 0C) values to the caller to prevent any wrong decisions made with
such values. NOTE: this allows the read functions not to be blocking
and allows the callers to make the decision if they would like to
block or try again later. At least the current user(thermal) seems to
handle this by retrying later.
A simpler alternative approach could be to sleep in the probe for the
duration required, but that will result in latency that is undesirable
and delay boot sequence un-necessarily.
[1] http://www.ti.com/lit/ds/symlink/tmp102.pdf
Cc: Eduardo Valentin <edubezval@gmail.com>
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Reported-by: Elvita Lobo <elvita@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Fixes: a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
PCI_DEVICE_ID_AMD_15H_M60H_NB_F3 is now defined in pci_ids.h
Signed-off-by: Adam Majer <adamm@zombino.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
This patch adds a member in fam15h_power_data which specifies the
maximum accumulated power in a compute unit.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attributes depend on the CPU model the driver gets loaded on.
Therefore, add those attributes dynamically at init time. This is more
flexible to control the different attributes on different platforms.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792 and NCT6793 are mostly register compatible to NCT6791, but
temperature sources are different and difficult to manage with a single
temperature label array. Introduce separate temperature label arrays
for those chips to reflect the differences.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both NCT6791D and NCT6792D permit selection of a 'virtual' temperature
register as temperature source. The virtual temperature registers are
registers 0xea to 0xef in bank 0 and can be written by software.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
when checking for the value of the shunt resistor.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Any sysfs "show" read access from the client app will result in reading
all registers (8 with ina226). Depending on the host this can limit the
best achievable read rate.
This changeset allows for individual register accesses through regmap.
Tested with BeagleBone Black (Baylibre-ACME) and ina226.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
A new limit selected arbitrarily as power of two greater than
required minimum for Xeon Phi processor (72 for Knights Landing).
Currently driver is not able to handle cores with core ID greater than 32.
Such attempt ends up with the following error in dmesg:
coretemp coretemp.0: Adding Core XXX failed
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TMP75C has a different control register layout and only supports
12-bit temperature samples (0.0625 deg C).
The continuous sample rate is ~12 Hz.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix module autoload for IBM and Open power platforms.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The description in the driver states: "ABX500 does not provide auto ADC,
so to monitor the required temperatures, a periodic work is used. It is
more important to not wake up the CPU... If the chip gets too hot during
a sleep state it's most likely due to external factors, such as the
surrounding temperature and nothing can be done in S/W."
So it makes no sense to keep IRQs enabled as it need not be wakeup
source. This patch removes the use of IRQF_NO_SUSPEND flag
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
max31790_update_device() return the error code in ERR_PTR. We were
checking if it has returned error or not but before checking we have
dereferenced it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support to create thermal zones based on the temperature sensors
provided by the SCP. The thermal zones can be defined using the
thermal DT bindings and should refer to the SCP sensor id to select
the sensor.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The STEP_UP_TIME and STEP_DOWN_TIME registers are swapped for all chips but
NCT6775.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck