Creates a /sys/fs/xfs/$dev/errortag/ directory to control the errortag
values directly. This enables us to control the randomness values,
rather than having to accept the defaults.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Remove the xfs_etest structure in favor of a per-mountpoint structure.
This will give us the flexibility to set as many error injection points
as we want, and later enable us to set up sysfs knobs to set the trigger
frequency as we wish. This comes at a cost of higher memory use, but
unti we hit 1024 injection points (we're at 29) or a lot of mounts this
shouldn't be a huge issue.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Log recovery allocates in-core transaction and member item data
structures on-demand as it processes the on-disk log. Transactions
are allocated on first encounter on-disk and stored in a hash table
structure where they are easily accessible for subsequent lookups.
Transaction items are also allocated on demand and are attached to
the associated transactions.
When a commit record is encountered in the log, the transaction is
committed to the fs and the in-core structures are freed. If a
filesystem crashes or shuts down before all in-core log buffers are
flushed to the log, however, not all transactions may have commit
records in the log. As expected, the modifications in such an
incomplete transaction are not replayed to the fs. The in-core data
structures for the partial transaction are never freed, however,
resulting in a memory leak.
Update xlog_do_recovery_pass() to first correctly initialize the
hash table array so empty lists can be distinguished from populated
lists on function exit. Update xlog_recover_free_trans() to always
remove the transaction from the list prior to freeing the associated
memory. Finally, walk the hash table of transaction lists as the
last step before it goes out of scope and free any transactions that
may remain on the lists. This prevents a memory leak of partial
transactions in the log.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
bmap returns a dumb LBA address but not the block device that goes with
that LBA. Swapfiles don't care about this and will blindly assume that
the data volume is the correct blockdev, which is totally bogus for
files on the rt subvolume. This results in the swap code doing IOs to
arbitrary locations on the data device(!) if the passed in mapping is a
realtime file, so just turn off bmap for rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Expose the readlink variant that doesn't take the inode lock so that
the scrubber can inspect symlink contents.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Teach the extended attribute reading functions to pass along a
transaction context if one was supplied. The extended attribute scrub
code will use transactions to lock buffers and avoid deadlocking with
itself in the case of loops; since it will already have the inode
locked, also create xattr get/list helpers that don't take locks.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Teach the directory reading functions to pass along a transaction context
if one was supplied. The directory scrub code will use transactions to
lock buffers and avoid deadlocking with itself in the case of loops.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Modify the existing dir leafn lasthash function to enable us to
calculate the highest hash value of a leaf1 block. This will be used by
the directory scrubbing code to check the sanity of hashes in leaf1
directory blocks.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor the inode fork block counting function to count extents for us
at the same time. This will be used by the bmbt scrubber function.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There is an inconsistency in the way that _bmap_count_blocks deals with
delalloc reservations -- if the specified fork is in extents format,
*count is set to the total number of blocks referenced by the in-core
fork, including delalloc extents. However, if the fork is in btree
format, *count is set to the number of blocks referenced by the on-disk
fork, which does /not/ include delalloc extents.
For the lone existing caller of _bmap_count_blocks this hasn't been an
issue because the function is only used to count xattr fork blocks
(where there aren't any delalloc reservations). However, when scrub
comes along it will use this same function to check di_nblocks against
both on-disk extent maps, so we need this behavior to be consistent.
Therefore, fix _bmap_count_leaves not to include delalloc extents and
remove unnecessary parameters.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Separate the "clear reflink flag" function into one function that checks
if the flag is needed, and a second function that checks and clears the
flag. The inode scrub code will want to check the necessity of the flag
without clearing it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Adapt _reflink_find_shared to take an optional transaction pointer. The
inode scrubber code will need to decide (within transaction context) if
a file has shared blocks. To avoid buffer deadlocks, we must pass the
tp through to this function's utility calls.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Check the inode cache for a particular inode number. If it's in the
cache, check that it's not currently being reclaimed. If it's not being
reclaimed, return zero if the inode is allocated. This function will be
used by various scrubbers to decide if the cache is more up to date
than the disk in terms of checking if an inode is allocated.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Create a function to extract an in-core inobt record from a generic
btree_rec union so that scrub will be able to check inobt records
and check inode block alignment.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Plumb in the pieces (init_high_key, diff_two_keys) necessary to call
query_range on the inode space and block mapping btrees and to extract
raw btree records. This will eventually be used by the inobt and bmbt
scrubbers.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Export various internal functions so that the online scrubber can use
them to check the state of metadata.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The btree record and key inorder check functions will be used by the
btree scrubber code, so make sure they're always built.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
This is a purely mechanical patch that removes the private
__{u,}int{8,16,32,64}_t typedefs in favor of using the system
{u,}int{8,16,32,64}_t typedefs. This is the sed script used to perform
the transformation and fix the resulting whitespace and indentation
errors:
s/typedef\t__uint8_t/typedef __uint8_t\t/g
s/typedef\t__uint/typedef __uint/g
s/typedef\t__int\([0-9]*\)_t/typedef int\1_t\t/g
s/__uint8_t\t/__uint8_t\t\t/g
s/__uint/uint/g
s/__int\([0-9]*\)_t\t/__int\1_t\t\t/g
s/__int/int/g
/^typedef.*int[0-9]*_t;$/d
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Don't bother wandering our way through the leaf nodes when the caller
issues a query_all; just zoom down the left side of the tree and walk
rightwards along level zero.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
When a buffer is modified, logged and committed, it ultimately ends
up sitting on the AIL with a dirty bli waiting for metadata
writeback. If another transaction locks and invalidates the buffer
(freeing an inode chunk, for example) in the meantime, the bli is
flagged as stale, the dirty state is cleared and the bli remains in
the AIL.
If a shutdown occurs before the transaction that has invalidated the
buffer is committed, the transaction is ultimately aborted. The log
items are flagged as such and ->iop_unlock() handles the aborted
items. Because the bli is clean (due to the invalidation),
->iop_unlock() unconditionally releases it. The log item may still
reside in the AIL, however, which means the I/O completion handler
may still run and attempt to access it. This results in assert
failure due to the release of the bli while still present in the AIL
and a subsequent NULL dereference and panic in the buffer I/O
completion handling. This can be reproduced by running generic/388
in repetition.
To avoid this problem, update xfs_buf_item_unlock() to first check
whether the bli is aborted and if so, remove it from the AIL before
it is released. This ensures that the bli is no longer accessed
during the shutdown sequence after it has been freed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If a filesystem shutdown occurs with a buffer log item in the CIL
and a log force occurs, the ->iop_unpin() handler is generally
expected to tear down the bli properly. This entails freeing the bli
memory and releasing the associated hold on the buffer so it can be
released and the filesystem unmounted.
If this sequence occurs while ->bli_refcount is elevated (i.e.,
another transaction is open and attempting to modify the buffer),
however, ->iop_unpin() may not be responsible for releasing the bli.
Instead, the transaction may release the final ->bli_refcount
reference and thus xfs_trans_brelse() is responsible for tearing
down the bli.
While xfs_trans_brelse() does drop the reference count, it only
attempts to release the bli if it is clean (i.e., not in the
CIL/AIL). If the filesystem is shutdown and the bli is sitting dirty
in the CIL as noted above, this ends up skipping the last
opportunity to release the bli. In turn, this leaves the hold on the
buffer and causes an unmount hang. This can be reproduced by running
generic/388 in repetition.
Update xfs_trans_brelse() to handle this shutdown corner case
correctly. If the final bli reference is dropped and the filesystem
is shutdown, remove the bli from the AIL (if necessary) and release
the bli to drop the buffer hold and ensure an unmount does not hang.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
gcc-7 flags the use of integer math inside of a condition
as a potential bug:
fs/xfs/xfs_bmap_util.c: In function 'xfs_swap_extents_check_format':
fs/xfs/xfs_bmap_util.c:1619:8: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
fs/xfs/xfs_bmap_util.c:1629:8: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
There is already a helper function for testing the di_forkoff
field for zero, so let's use that instead to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The t_lsn is not used anymore and the t_commit_lsn is used as a tmp
storage for the checkpoint sequence number only in the current code.
And the start/commit lsn are tracked as a transaction group tag in
the xfs_cil_ctx instead of a single transaction, so remove them from
the xfs_trans structure and their users to match with the design.
Signed-off-by: Shan Hai <shan.hai@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS_HSIZE is an extremly confusing way to calculate the size of handle_t.
Given that handle_t always only had two sizes, and one of them isn't
even covered by XFS_HSIZE to start with just remove the macro and use
a constant sizeof expression.
Note that XFS_HSIZE isn't used in xfsprogs, xfsdump or xfstests either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If a transaction log reservation overrun occurs, the ticket data
associated with the reservation is dumped in xfs_log_commit_cil().
This occurs long after the transaction items and details have been
removed from the transaction and effectively lost. This limited set
of ticket data provides very little information to support debugging
transaction overruns based on the typical report.
To improve transaction log reservation overrun reporting, create a
helper to dump transaction details such as log items, log vector
data, etc., as well as the underlying ticket data for the
transaction. Move the overrun detection from xfs_log_commit_cil() to
xlog_cil_insert_items() so it occurs prior to migration of the
logged items to the CIL. Call the new helper such that it is able to
dump this transaction data before it is lost.
Also, warn on overrun to provide callstack context for the offending
transaction and include a few additional messages from
xlog_cil_insert_items() to display the reservation consumed locally
for overhead such as log vector headers, split region headers and
the context ticket. This provides a complete general breakdown of
the reservation consumption of a transaction when/if it happens to
overrun the reservation.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Transaction reservation overrun detection currently occurs too late
to print useful information about the offending transaction.
Ideally, the transaction data is printed before the associated log
items are moved from the transaction to the CIL, which occurs in
xlog_cil_insert_items(), such that details of the items logged by
the transaction are available for analysis.
Refactor xlog_cil_insert_items() to facilitate moving tx overrun
detection to this function. Update the function to track each bit of
extra log reservation stolen from the transaction (i.e., such as for
the CIL context ticket) and perform the log item migration as the
last operation before the CIL lock is released. This creates a
context where the transaction reservation consumption has been fully
calculated when the log items are moved to the CIL. This patch makes
no functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xlog_print_tic_res() pre-dates delayed logging and the committed
items list (CIL) and thus retains some factoring warts, such as hard
coded function names in the output and the fact that it induces a
shutdown.
In preparation for more detailed logging of regular transaction
overrun situations, refactor xlog_print_tic_res() to be slightly
more generic. Reword some of the warning messages and pull the
shutdown into the callers.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
While configurable at runtime, the DEBUG mode assert failure
behavior is usually either desired or not for a particular
situation. For example, developers using kernel modules may prefer
for fatal asserts to remain disabled across module reloads while QE
engineers doing broad regression testing may prefer to have fatal
asserts enabled on boot to facilitate data collection for bug
reports.
To provide a compromise/convenience for developers, create a Kconfig
option that sets the default value of the DEBUG mode 'bug_on_assert'
sysfs tunable. The default behavior remains to trigger kernel BUGs
on assert failures to preserve existing behavior across kernel
configuration updates with DEBUG mode enabled.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
In DEBUG mode, assert failures unconditionally trigger a kernel BUG.
This is useful in diagnostic situations to panic a system and
collect detailed state information at the time of a failure.
This can also cause problems in cases where DEBUG mode code is
desired but it is preferable not trigger kernel BUGs on assert
failure. For example, during development of new code or during
certain xfstests tests that intentionally cause corruption and test
the kernel for survival (but otherwise may expect to trigger assert
failures).
To provide additional flexibility, create the
<sysfs>/fs/xfs/debug/bug_on_assert tunable to configure assert
failure behavior at runtime. This tunable is only available in DEBUG
mode and is enabled by default to preserve existing default
behavior. When disabled, assert failures in DEBUG mode result in
kernel warnings.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
In a pathological scenario where we are trying to bunmapi a single
extent in which every other block is shared, it's possible that trying
to unmap the entire large extent in a single transaction can generate so
many EFIs that we overflow the transaction reservation.
Therefore, use a heuristic to guess at the number of blocks we can
safely unmap from a reflink file's data fork in an single transaction.
This should prevent problems such as the log head slamming into the tail
and ASSERTs that trigger because we've exceeded the transaction
reservation.
Note that since bunmapi can fail to unmap the entire range, we must also
teach the deferred unmap code to roll into a new transaction whenever we
get low on reservation.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
[hch: random edits, all bugs are my fault]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, the dir2 leaf block getdents function uses a complex state
tracking mechanism to create a shadow copy of the block mappings and
then uses the shadow copy to schedule readahead. Since the read and
readahead functions are perfectly capable of reading the mappings
themselves, we can tear all that out in favor of a simpler function that
simply keeps pushing the readahead window further out.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reclaim during quotacheck can lead to deadlocks on the dquot flush
lock:
- Quotacheck populates a local delwri queue with the physical dquot
buffers.
- Quotacheck performs the xfs_qm_dqusage_adjust() bulkstat and
dirties all of the dquots.
- Reclaim kicks in and attempts to flush a dquot whose buffer is
already queud on the quotacheck queue. The flush succeeds but
queueing to the reclaim delwri queue fails as the backing buffer is
already queued. The flush unlock is now deferred to I/O completion
of the buffer from the quotacheck queue.
- The dqadjust bulkstat continues and dirties the recently flushed
dquot once again.
- Quotacheck proceeds to the xfs_qm_flush_one() walk which requires
the flush lock to update the backing buffers with the in-core
recalculated values. It deadlocks on the redirtied dquot as the
flush lock was already acquired by reclaim, but the buffer resides
on the local delwri queue which isn't submitted until the end of
quotacheck.
This is reproduced by running quotacheck on a filesystem with a
couple million inodes in low memory (512MB-1GB) situations. This is
a regression as of commit 43ff2122e6 ("xfs: on-stack delayed write
buffer lists"), which removed a trylock and buffer I/O submission
from the quotacheck dquot flush sequence.
Quotacheck first resets and collects the physical dquot buffers in a
delwri queue. Then, it traverses the filesystem inodes via bulkstat,
updates the in-core dquots, flushes the corrected dquots to the
backing buffers and finally submits the delwri queue for I/O. Since
the backing buffers are queued across the entire quotacheck
operation, dquot reclaim cannot possibly complete a dquot flush
before quotacheck completes.
Therefore, quotacheck must submit the buffer for I/O in order to
cycle the flush lock and flush the dirty in-core dquot to the
buffer. Add a delwri queue buffer push mechanism to submit an
individual buffer for I/O without losing the delwri queue status and
use it from quotacheck to avoid the deadlock. This restores
quotacheck behavior to as before the regression was introduced.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- Fix some bogus ASSERT failures on CONFIG_SMP=n and CONFIG_XFS_DEBUG=y.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJZQhB9AAoJEPh/dxk0SrTrMWsP/A1gSHmaS2UI3WvXdqwAxldy
GiDZ3oSAhn4SF7BY+AhIu+Ot9kwCyOVzd/RZ9zVYmRjTTFxYX7P099uua2e/mf70
Z1o9oSk9H76srqo7L76h7lI2ONsgd28aqh082hmDrRUhhwy7LZThVV15ZPZFfgU4
8Q17h0uRUVgSn8M8INsuiMpw1sCLJsXw/9Rb9iFMgi3tSJaGZ1Mm//nA1aeS8HFH
xCKHYw7YUtVKtIVyVV1NGdtXhXZbNznJXelkUZLMnMgOOmAqWiUa8FOGPNbQEezX
1VidjzGhxRF7uoUJNnnX5mM+26c8/Ip4cLtqvnFQo30bx+HXO3OR8jywQO+6DD9Q
NxFHY5D/Peud96xsnq5mRzNMN5fqumyVAyUCXSebT3Oa42HMdva+66s9JoFfDehi
Z7VmRdoryxexDRbhiQVev4xe20beLtOHAP2I5JrnJddrXb0aFWowLk776wa0uxD8
7cbKgovikqSHk4/mqpyZ5iQeaufg/kOi2cNaTcAFeCbvbXYieeRXVlisMBh1DKec
lSX5e4kNNS20VVbCYakAttK69lpZzuraYPDDsnb4HRlmt0VX12lYyqQwklY/YZ9S
jDagtKWKDm/L/jq2j5Nd3uSycM+lMaq97mIMjzPRrnPjOriME1ZGLwEQbKfBLXnW
3Flzt5C2Hk1Fb/VlNx4S
=U99d
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.12-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"One more bugfix for you for 4.12-rc6 to fix something that came up in
an earlier rc:
- Fix some bogus ASSERT failures on CONFIG_SMP=n and CONFIG_XFS_DEBUG=y"
* tag 'xfs-4.12-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix spurious spin_is_locked() assert failures on non-smp kernels
The 0-day kernel test robot reports assertion failures on
!CONFIG_SMP kernels due to failed spin_is_locked() checks. As it
turns out, spin_is_locked() is hardcoded to return zero on
!CONFIG_SMP kernels and so this function cannot be relied on to
verify spinlock state in this configuration.
To avoid this problem, replace the associated asserts with lockdep
variants that do the right thing regardless of kernel configuration.
Drop the one assert that checks for an unlocked lock as there is no
suitable lockdep variant for that case. This moves the spinlock
checks from XFS debug code to lockdep, but generally provides the
same level of protection.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- Fix an unmount hang due to a race in io buffer accounting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wRbJ
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.12-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fix from Darrick Wong:
"I've one more bugfix for you for 4.12-rc4: Fix an unmount hang due to
a race in io buffer accounting"
* tag 'xfs-4.12-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use ->b_state to fix buffer I/O accounting release race
We've had user reports of unmount hangs in xfs_wait_buftarg() that
analysis shows is due to btp->bt_io_count == -1. bt_io_count
represents the count of in-flight asynchronous buffers and thus
should always be >= 0. xfs_wait_buftarg() waits for this value to
stabilize to zero in order to ensure that all untracked (with
respect to the lru) buffers have completed I/O processing before
unmount proceeds to tear down in-core data structures.
The value of -1 implies an I/O accounting decrement race. Indeed,
the fact that xfs_buf_ioacct_dec() is called from xfs_buf_rele()
(where the buffer lock is no longer held) means that bp->b_flags can
be updated from an unsafe context. While a user-level reproducer is
currently not available, some intrusive hacks to run racing buffer
lookups/ioacct/releases from multiple threads was used to
successfully manufacture this problem.
Existing callers do not expect to acquire the buffer lock from
xfs_buf_rele(). Therefore, we can not safely update ->b_flags from
this context. It turns out that we already have separate buffer
state bits and associated serialization for dealing with buffer LRU
state in the form of ->b_state and ->b_lock. Therefore, replace the
_XBF_IN_FLIGHT flag with a ->b_state variant, update the I/O
accounting wrappers appropriately and make sure they are used with
the correct locking. This ensures that buffer in-flight state can be
modified at buffer release time without racing with modifications
from a buffer lock holder.
Fixes: 9c7504aa72 ("xfs: track and serialize in-flight async buffers against unmount")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Tested-by: Libor Pechacek <lpechacek@suse.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- Fix indlen block reservation accounting bug when splitting delalloc extent
- Fix warnings about unused variables that appeared in -rc1.
- Don't spew errors when bmapping a local format directory
- Fix an off-by-one error in a delalloc eof assertion
- Make fsmap only return inode information for CAP_SYS_ADMIN
- Fix a potential mount time deadlock recovering cow extents
- Fix unaligned memory access in _btree_visit_blocks
- Fix various SEEK_HOLE/SEEK_DATA bugs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pDjl
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fixes from Darrick Wong:
"A few miscellaneous bug fixes & cleanups:
- Fix indlen block reservation accounting bug when splitting delalloc
extent
- Fix warnings about unused variables that appeared in -rc1.
- Don't spew errors when bmapping a local format directory
- Fix an off-by-one error in a delalloc eof assertion
- Make fsmap only return inode information for CAP_SYS_ADMIN
- Fix a potential mount time deadlock recovering cow extents
- Fix unaligned memory access in _btree_visit_blocks
- Fix various SEEK_HOLE/SEEK_DATA bugs"
* tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
xfs: Fix missed holes in SEEK_HOLE implementation
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs: fix unaligned access in xfs_btree_visit_blocks
xfs: avoid mount-time deadlock in CoW extent recovery
xfs: only return detailed fsmap info if the caller has CAP_SYS_ADMIN
xfs: bad assertion for delalloc an extent that start at i_size
xfs: fix warnings about unused stack variables
xfs: BMAPX shouldn't barf on inline-format directories
xfs: fix indlen accounting error on partial delalloc conversion
Currently several places in xfs_find_get_desired_pgoff() handle the case
of a missing page. Make them all handled in one place after the loop has
terminated.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There is an off-by-one error in loop termination conditions in
xfs_find_get_desired_pgoff() since 'end' may index a page beyond end of
desired range if 'endoff' is page aligned. It doesn't have any visible
effects but still it is good to fix it.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as
can be seen by the following command:
xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k"
-c "seek -h 0" file
wrote 57344/57344 bytes at offset 0
56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec)
wrote 8192/8192 bytes at offset 131072
8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec)
Whence Result
HOLE 139264
Where we can see that hole at offset 56k was just ignored by SEEK_HOLE
implementation. The bug is in xfs_find_get_desired_pgoff() which does
not properly detect the case when pages are not contiguous.
Fix the problem by properly detecting when found page has larger offset
than expected.
CC: stable@vger.kernel.org
Fixes: d126d43f63
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_find_get_desired_pgoff() is used to search for offset of hole or
data in page range [index, end] (both inclusive), and the max number
of pages to search should be at least one, if end == index.
Otherwise the only page is missed and no hole or data is found,
which is not correct.
When block size is smaller than page size, this can be demonstrated
by preallocating a file with size smaller than page size and writing
data to the last block. E.g. run this xfs_io command on a 1k block
size XFS on x86_64 host.
# xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \
-c "seek -d 0" /mnt/xfs/testfile
wrote 1024/1024 bytes at offset 2048
1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec)
Whence Result
DATA EOF
Data at offset 2k was missed, and lseek(2) returned ENXIO.
This is uncovered by generic/285 subtest 07 and 08 on ppc64 host,
where pagesize is 64k. Because a recent change to generic/285
reduced the preallocated file size to smaller than 64k.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This structure copy was throwing unaligned access warnings on sparc64:
Kernel unaligned access at TPC[1043c088] xfs_btree_visit_blocks+0x88/0xe0 [xfs]
xfs_btree_copy_ptrs does a memcpy, which avoids it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If a malicious user corrupts the refcount btree to cause a cycle between
different levels of the tree, the next mount attempt will deadlock in
the CoW recovery routine while grabbing buffer locks. We can use the
ability to re-grab a buffer that was previous locked to a transaction to
avoid deadlocks, so do that here.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There were a number of handwaving complaints that one could "possibly"
use inode numbers and extent maps to fingerprint a filesystem hosting
multiple containers and somehow use the information to guess at the
contents of other containers and attack them. Despite the total lack of
any demonstration that this is actually possible, it's easier to
restrict access now and broaden it later, so use the rmapbt fsmap
backends only if the caller has CAP_SYS_ADMIN. Unprivileged users will
just have to make do with only getting the free space and static
metadata placement information.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
By run fsstress long enough time enough in RHEL-7, I find an
assertion failure (harder to reproduce on linux-4.11, but problem
is still there):
XFS: Assertion failed: (iflags & BMV_IF_DELALLOC) != 0, file: fs/xfs/xfs_bmap_util.c
The assertion is in xfs_getbmap() funciton:
if (map[i].br_startblock == DELAYSTARTBLOCK &&
--> map[i].br_startoff <= XFS_B_TO_FSB(mp, XFS_ISIZE(ip)))
ASSERT((iflags & BMV_IF_DELALLOC) != 0);
When map[i].br_startoff == XFS_B_TO_FSB(mp, XFS_ISIZE(ip)), the
startoff is just at EOF. But we only need to make sure delalloc
extents that are within EOF, not include EOF.
Signed-off-by: Zorro Lang <zlang@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reduce stack usage and get rid of compiler warnings by eliminating
unused variables.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
When we're fulfilling a BMAPX request, jump out early if the data fork
is in local format. This prevents us from hitting a debugging check in
bmapi_read and barfing errors back to userspace. The on-disk extent
count check later isn't sufficient for IF_DELALLOC mode because da
extents are in memory and not on disk.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The delalloc -> real block conversion path uses an incorrect
calculation in the case where the middle part of a delalloc extent
is being converted. This is documented as a rare situation because
XFS generally attempts to maximize contiguity by converting as much
of a delalloc extent as possible.
If this situation does occur, the indlen reservation for the two new
delalloc extents left behind by the conversion of the middle range
is calculated and compared with the original reservation. If more
blocks are required, the delta is allocated from the global block
pool. This delta value can be characterized as the difference
between the new total requirement (temp + temp2) and the currently
available reservation minus those blocks that have already been
allocated (startblockval(PREV.br_startblock) - allocated).
The problem is that the current code does not account for previously
allocated blocks correctly. It subtracts the current allocation
count from the (new - old) delta rather than the old indlen
reservation. This means that more indlen blocks than have been
allocated end up stashed in the remaining extents and free space
accounting is broken as a result.
Fix up the calculation to subtract the allocated block count from
the original extent indlen and thus correctly allocate the
reservation delta based on the difference between the new total
requirement and the unused blocks from the original reservation.
Also remove a bogus assert that contradicts the fact that the new
indlen reservation can be larger than the original indlen
reservation.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Tetsuo reports:
fs/built-in.o: In function `xfs_file_iomap_end':
xfs_iomap.c:(.text+0xe0ef9): undefined reference to `put_dax'
fs/built-in.o: In function `xfs_file_iomap_begin':
xfs_iomap.c:(.text+0xe1a7f): undefined reference to `dax_get_by_host'
make: *** [vmlinux] Error 1
$ grep DAX .config
CONFIG_DAX=m
# CONFIG_DEV_DAX is not set
# CONFIG_FS_DAX is not set
When FS_DAX=n we can/must throw away the dax code in filesystems.
Implement 'fs_' versions of dax_get_by_host() and put_dax() that are
nops in the FS_DAX=n case.
Cc: <linux-xfs@vger.kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Fixes: ef51042472 ("block, dax: move 'select DAX' from BLOCK to FS_DAX")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
Darrick J. Wong