Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This enables debouncing of the I2C lines. The debounce period is
2 * the debounce register field value, in terms of the I2C block's main
clock. The Tegra TRM indicates that a setting yielding >50nS is
desirable. Hence, a setting of 2 => 4 clocks @ 72MHz => ~55nS.
Signed-off-by: Ken Radtke <kradtke@nvidia.com>
[swarren: Added commit description body,
Fixed 80-column limit, Reverted file permission change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A repeated start should be used for all but the last msg in an xfer. The
NOSTART flag is for skipping the START frame (addr/rw)
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Re-init the I2C controller when an IRQ arrives with no
I2C_INT_STATUS bits set to indicate why the interrupt was sent.
Storms of such mystery interrupts are infrequently seen.
Dump some more status when these interrupts arrive. Set an error
for the current request and wake up the requester (rather than
timing out the request or possibly silently ignoring the interrupts).
If the I2C block is inside the DVC, also ACK the DVC I2C transfer
done interrupt in the ISR error return path, as is done for the
normal return path.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
[swarren: Fix minor checkpatch whitespace issue, commit tag]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For Tegra i2c controller to function properly new slave mode must be
enabled.
swarren notes:
In particular, I found this was needed when working on enabling the
Tegra audio driver on the Seaboard board. There are two different PCB
layouts for this board; a "clamshell" version, which works just fine
without this change, and the original non-clamshell version, which needs
this change in order for I2C to operate correctly. Without it, I2C
probing fails for some devices, e.g. with:
wm8903 0-001a: Device with ID register 0 is not a WM8903
wm8903 0-001a: asoc: failed to probe CODEC wm8903.0-001a: -19
asoc: failed to instantiate card tegra-wm8903: -19
ALSA device list:
No soundcards found.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use a standard list with proper locking to handle the list of
adapters. Thankfully it only matters on systems with more than one
parallel port, which are very rare.
Thanks to Lukasz Kapiec for reporting the problem to me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Move the SMBus device ID definitions of recent devices from pci_ids.h
to the i2c-i801.c driver file. They don't have to be shared, as they
are clearly identified and only used in this driver. In the future,
such IDs will go to i2c-i801 directly. This will make adding support
for new devices much faster and easier, as it will avoid cross-
subsystem patch sets and merge conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch enables I2C driver autoloading on sh-mobile systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [.38 down to .34]
When warning on the use of deprecated i2c_driver methods
attach_adapter and detach_adapter, mention the name of the driver
which needs to be updated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
isr is passed later into i2c_pxa_irq_txempty and
i2c_pxa_irq_rxfull and they may use some other bits
than irq sources.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix regression that was introduced by dynamic register layout.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
the of_node will auto-publish devices which are added to the device
tree.
Commit 925bb9c6 aka ("of/i2c: Fix module load order issue caused by
of_i2c.c) moved the of_i2c_register_devices() function from the i2c core
back to the drivers. This patch does the same thing for the pxa driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
timeout here maybe 0 if the event occured and a task with a higher
priority stole the cpu and we were sleeping longer than the timeout
value we specified.
In case of a real timeout I changed the error code to I2C_RETRY so we
retry the transfer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sodaville has three of them on a single IRQ. IRQF_DISABLED is removed
because it is a NOP allready and scheduled for removal.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Sodaville I2C controller is almost the same as found on PXA2xx. The
difference:
- the register are at a different offset
- no slave support
The PCI probe code adds three platform devices which are probed then by
the platform code.
The X86 part also adds dummy clock defines because we don't have HW
clock support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This will prepare the driver to handle register layouts where certain
registers are not available at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
mxs_reset_block() clears the PIO_QUEUE_MODE bit. So we have
to set it again after a controller reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the SMBus Controller DeviceIDs for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The last legitimate user of i2c_driver.attach_adapter and
.detach_adapter is gone, so we can finally deprecate these callbacks.
The last few drivers which still use these will have to be updated to
make use of standard I2C device instantiation ways instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the standard driver core mechanism to keep track of i2c adapters
present on the system: i2c_for_each_dev and a notifier. This will let
us deprecate and ultimately remove the legacy attach_adapter and
detach_adapter callbacks in i2c_driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Introduce i2c_for_each_dev(), an i2c device iterator with proper
locking for use by i2c-dev. This is needed so that we can get rid of
the attach_adapter and detach_adapter legacy callback functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the parameter of i2c_get_adapter() to "nr", to make it clear we
are passing an adapter number and not an adapter ID (which have gone
away by now.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus/2639/i2c-1' of git://git.fluff.org/bjdooks/linux:
i2c-mpc: Add support for 64bit system
i2c: add driver for Freescale i.MX28
i2c: tegra: Add i2c support
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
change from original version -- by advice of Jean Delvare
1. remove global variable i2c_reg, replaced by local variables
2. replace ENXIO with ENODEV when no platform resources
3. add adapter->nr assignment before i2c_add_numbered_adapter() call
4. add judgement for i2c_del_adapter() return value
5. release adapter when driver removed
6. add __devexit for puv3_i2c_remove() function
7. modify several names to more appropriated ones
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
Currently i2c-mpc supports 32bit system only, this modification makes it
supported on both 32-bit and 64-bit systems. The P5020 is the first
64-bit PPC system with the i2c-mpc controller.
Based in patch from Xulei <B33228@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values. This patch fixed the following build
warning:
CC drivers/i2c/busses/i2c-ocores.o
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.
This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support new device OKI SEMICONDUCTOR ML7213 IOH.
The ML7213 which is for IVI(In-Vehicle Infotainment) is a companion
chip for the Atom E6xx series and compatible with the Intel EG20T
PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently only supporting the PIOQUEUE-mode, because DMA-support for
this platform is not yet in mainline. When it becomes available and
support has been added to this driver, it will also be suitable for
i.MX23 and STMP3xxx.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Adds I2C bus driver for nVidia Tegra SoCs. Tegra includes 4 I2C
controllers, one of which is inside the Dynamic Voltage Controller
and has a slightly different register map.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use strlcpy instead of strncpy.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for the Diolan U2C-12 USB-I2C adapter.
It also updates MAINTAINERS to list the author as maintainer.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/i2c-2638' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: move setup to the earlier subsys initcall
i2c-bfin-twi: handle faulty slave devices better
i2c-mv64xxx: send repeated START between messages in xfer
i2c-nomadik: fix regression on adapter name
i2c-omap: Set latency requirements only once for several messages
i2c-eg20t: add driver for Intel EG20T
i2c-ocores: add some device tree documentation
i2c-ocores: Use devres for resource allocation
i2c-ocores: Adapt for device tree
i2c-iop3xx: add iomem annotation
Some systems using this bus sometimes have very basic devices such as
regulators on the bus, so the I2C bus master needs to be loaded early.
This also matches the behavior of many other I2C bus master drivers.
Therefore initialize via subsys_initcall().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Faulty slave devices might drive SDA low after a transfer finishes. So,
when this scenario is detected, have the master generate up to 9 extra
clocks until the SDA is properly released.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 5a0e3ad6af added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this. On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As stated into file include/linux/i2c.h we must send a repeated START
between messages in the same xfer groupset:
* Except when I2C "protocol mangling" is used, all I2C adapters implement
* the standard rules for I2C transactions. Each transaction begins with a
* START. That is followed by the slave address, and a bit encoding read
* versus write. Then follow all the data bytes, possibly including a byte
* with SMBus PEC. The transfer terminates with a NAK, or when all those
* bytes have been transferred and ACKed. If this is the last message in a
* group, it is followed by a STOP. Otherwise it is followed by the next
* @i2c_msg transaction segment, beginning with a (repeated) START.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Mauro Barella <mbarella@vds-it.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Nomadik I2C adapter does not provide a name for the struct
passed into i2c_add_numbered_adapter() causing a regression on
2.6.37-rc3 due to commit 2236baa75f
adding sanity checks for adapters. Fix this by providing a name
proper.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This puts some documentation for the device tree configuration at the head
of the driver file. Hopefully this can get moved to a common area for this
type of documentation at a later date; unfortunately, there isn't really
such a place in the kernel tree at this time.
Furthermore, the regstep and clock-frequency parameters are really bus
parameters and should probably be passed to the driver in a better way.
Consider that a TODO.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch converts the i2c-cores driver to use devres routines for
resource allocation.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adapts the i2c-ocores driver for being defined and configured via
a device tree description.
The device tree bits need to be protected by CONFIG_OF guards as this is
still an optional feature.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Eliminate unnecessary casts and the following sparse warnings:
drivers/i2c/busses/i2c-iop3xx.c:65:9: warning: incorrect type in argument 1 (different base types)
drivers/i2c/busses/i2c-iop3xx.c:65:9: expected void const volatile [noderef] <asn:2>*<noident>
drivers/i2c/busses/i2c-iop3xx.c:65:9: got unsigned int
[ the previous warning is repeated 18 times ]
drivers/i2c/busses/i2c-iop3xx.c:456:33: warning: cast removes address space of expression
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.
On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
This patch converts the i2c driver to use PM runtime apis
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-2637/i2c-all' of git://git.fluff.org/bjdooks/linux:
i2c-intel-mid: Driver depends on PCI
i2c-intel-mid: support for Moorestown and Medfield platform
i2c-nomadik: fixup bus delays
i2c-nomadik: support smbus emulation
i2c-nomadik: dynamic clocking
i2c-nomadik: documentation fixes
i2c-s3c2410: Enable i2c clock only when doing some transfert
i2c-intel-mid driver uses PCI data structs and interfaces,
so it should depend on PCI. Fixes these build errors:
drivers/i2c/busses/i2c-intel-mid.c:977: error: implicit declaration of function 'pci_request_region'
drivers/i2c/busses/i2c-intel-mid.c:1077: error: implicit declaration of function 'pci_release_region'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ba Zheng <zheng.ba@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
Tomoya MORINAGA