This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e8620 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com>
CC: Ming Lei <tom.leiming@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"length" is type size_t so the cast to unsigned int truncates the
upper bytes. This isn't an issue in real life (I've checked the
callers) but it's a bit messy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit e534c5b831 (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1476) fixes a regression introduced by
fccf4e8620 (USB: Free bandwidth when
usb_disable_device is called). usb_disconnect() grabs the
bandwidth_mutex before calling usb_disable_device(), which calls down
indirectly to usb_set_interface(), which tries to acquire the
bandwidth_mutex.
The fix causes usb_set_interface() to return early when it is called
for an interface that has already been unregistered, which is what
happens in usb_disable_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tanya ran into an issue when trying to switch a UAS device from the BOT
configuration to the UAS configuration via the bConfigurationValue sysfs
file. Before installing the UAS configuration, set_bConfigurationValue()
calls usb_disable_device(). That function is supposed to remove all host
controller resources associated with that device, but it leaves some state
in the xHCI host controller.
Commit 0791971ba8
usb: allow drivers to use allocated bandwidth until unbound
added a call to usb_disable_device() in usb_set_configuration(), before
the xHCI bandwidth functions were invoked. That commit fixed a bug, but
also introduced a bug that is triggered when a configured device is
switched to a new configuration.
usb_disable_device() goes through all the motions of unbinding the drivers
attached to active interfaces and removing the USB core structures
associated with those interfaces, but it doesn't actually remove the
endpoints from the internal xHCI host controller bandwidth structures.
When usb_disable_device() calls usb_disable_endpoint() with reset_hardware
set to true, the entries in udev->ep_out and udev->ep_in will be set to
NULL. Usually, when the USB core installs a new configuration,
usb_hcd_alloc_bandwidth() will drop all non-NULL endpoints in udev->ep_out
and udev->ep_in before adding any new endpoints. However, when the new
UAS configuration was added, all those entries were null, so none of the
old endpoints in the BOT configuration were dropped.
The xHCI driver blindly added the UAS configuration endpoints, and some of
the endpoint addresses overlapped with the old BOT configuration
endpoints. This caused the xHCI host to reject the Configure Endpoint
command. Now that the xHCI driver code is cleaned up to reject a
double-add of active endpoints, we need to fix the USB core to properly
drop old endpoints in usb_disable_device().
If the host controller driver needs bandwidth checking support, make
usb_disable_device() call usb_disable_endpoint() with
reset_hardware set to false, drop the endpoints from the xHCI host
controller, and then call usb_disable_endpoint() again with
reset_hardware set to true.
The first call to usb_disable_endpoint() will cancel any pending URBs and
wait on them to be freed in usb_hcd_disable_endpoint(), but will keep the
pointers in udev->ep_out and udev->ep in intact. Then
usb_hcd_alloc_bandwidth() will use those pointers to know which endpoints
to drop.
The final call to usb_disable_endpoint() will do two things:
1. It will call usb_hcd_disable_endpoint() again, which should be harmless
since the ep->urb_list should be empty after the first call to
usb_disable_endpoint() returns.
2. It will set the entries in udev->ep_out and udev->ep in to NULL, and call
usb_hcd_disable_endpoint(). That call will have no effect, since the xHCI
driver doesn't set the endpoint_disable function pointer.
Note that usb_disable_device() will now need to be called with
hcd->bandwidth_mutex held.
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Tanya Brokhman <tlinder@codeaurora.org>
Cc: ablay@codeaurora.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow
the pointer to be shared across usb_hcds for the upcoming work to split
the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since the runtime-PM core already defines a .last_busy field in
device.power, this patch uses it to replace the .last_busy field
defined in usb_device and uses pm_runtime_mark_last_busy to implement
usb_mark_last_busy.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call pm_runtime_no_callbacks to set no_callbacks flag for USB
interfaces. Since interfaces cannot be power-managed separately from
their parent devices, there's no reason for the runtime-PM core to
invoke any callbacks for them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1430) fixes a bug in usbcore. When a device
configuration change occurs or a device is removed, the endpoints for
the old config should be completely disabled. However it turns out
they aren't; this is because usb_unbind_interface() calls
usb_enable_interface() or usb_set_interface() to put interfaces back
in altsetting 0, which re-enables the interfaces' endpoints.
As a result, when a device goes through a config change or is
unconfigured, the ep_in[] and ep_out[] arrays may be left holding old
pointers to usb_host_endpoint structures. If the device is
deauthorized these structures get freed, and the stale pointers cause
errors when the the device is eventually unplugged.
The solution is to disable the endpoints after unbinding the
interfaces instead of before. This isn't as large a change as it
sounds, since usb_unbind_interface() disables all the interface's
endpoints anyway before calling the driver's disconnect routine,
unless the driver claims to support "soft" unbind.
This fixes Bugzilla #19192. Thanks to "Tom" Lei Ming for diagnosing
the underlying cause of the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Carsten Sommer <carsten_sommer@ymail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.
Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth. We musn't change the bandwidth allocations until after the
unbinding is done. So this patch is indeed necessary."
Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference. An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1377) simplifies the code in usb_sg_init(), without
changing its functionality. It also removes a couple of unused fields
from the usb_sg_request structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the type of the URB's 'sg' pointer from a usb_sg_request to
a scatterlist. This allows drivers to submit scatter-gather lists
without using the usb_sg_wait() interface. It has the added benefit
of removing the typecasts that were added as part of patch as1368 (and
slightly decreasing the number of pointer dereferences).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converting a pipe number to a struct usb_host_endpoint pointer is a little
messy. Introduce a new convenience function to hide the mess.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1368) fixes a rather obscure bug in usbmon: When tracing
URBs sent by the scatter-gather library, it accesses the data buffers
while they are still mapped for DMA.
The solution is to move the mapping and unmapping out of the s-g
library and into the usual place in hcd.c. This requires the addition
of new URB flag bits to describe the kind of mapping needed, since we
have to call dma_map_sg() if the HCD supports native scatter-gather
operation and dma_map_page() if it doesn't. The nice thing about
having the new flags is that they simplify the testing for unmapping.
The patch removes the only caller of usb_buffer_[un]map_sg(), so those
functions are #if'ed out. A later patch will remove them entirely.
As a result of this change, urb->sg will be set in situations where
it wasn't set previously. Hence the xhci and whci drivers are
adjusted to test urb->num_sgs instead, which retains its original
meaning and is nonzero only when the HCD has to handle a scatterlist.
Finally, even when a submission error occurs we don't want to hand
URBs to usbmon before they are unmapped. The submission path is
rearranged so that map_urb_for_dma() is called only for non-root-hub
URBs and unmap_urb_for_dma() is called immediately after a submission
error. This simplifies the error handling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While looping over the interfaces, if usb_hcd_alloc_bandwidth() fails it calls
hcd->driver->reset_bandwidth(), so there was no need to reinstate the interface
again.
If no break occurred, the index equals config->desc.bNumInterfaces. A
subsequent usb_control_msg() failure resulted in a read from
config->interface[config->desc.bNumInterfaces] at label reset_old_alts.
In either case the last interface should be skipped.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/core/message.c:1583:6: warning: symbol '__usb_queue_reset_device' was not declared. Should it be static?
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the USB core check the bandwidth when switching from one
interface alternate setting to another. Also check the bandwidth
when resetting a configuration (so that alt setting 0 is used). If
this check fails, the device's state is unchanged. If the device
refuses the new alt setting, re-instate the old alt setting in the
host controller hardware.
If a USB device doesn't have an alternate interface setting 0, install
the first alt setting in its descriptors when a new configuration is
requested, or the device is reset.
Add a mutex per root hub to protect bandwidth operations:
adding/reseting/changing configurations, and changing alternate interface
settings. We want to ensure that the xHCI host controller and the USB
device are set up for the same configurations and alternate settings.
There are two (possibly three) steps to do this:
1. The host controller needs to check that bandwidth is available for a
different setting, by issuing and waiting for a configure endpoint
command.
2. Once that returns successfully, a control message is sent to the
device.
3. If that fails, the host controller must be notified through another
configure endpoint command.
The mutex is used to make these three operations seem atomic, to prevent
another driver from using more bandwidth for a different device while
we're in the middle of these operations.
While we're touching the bandwidth code, rename usb_hcd_check_bandwidth()
to usb_hcd_alloc_bandwidth(). This function does more than just check
that the bandwidth change won't exceed the bus bandwidth; it actually
changes the bandwidth configuration in the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1298) fixes a bug in the new scatter-gather URB
facility. If an URB uses a scatterlist then it should not have the
URB_NO_INTERRUPT flag set; otherwise the system won't be notified when
the transfer completes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The WHCI HCD will also support urbs with scatter-gather lists. Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD. Use this to decide whether to pass the scatter-list to the HCD
or not.
Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fix permits the "new" usbmon to access usb-storage's data buffer
without DMA remapping tricks. It should be compatible with PIO controllers
and not add any new crashes. Note that from now on PIO controllers and
usbmon are uniform in their access pattern and if one crashes then
the other will too. Hopefuly neither does.
As a side effect, we get rid for #ifdefs, which were a little ugly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b7af0bb ("USB: allow malformed LANGID descriptors") broke support
for devices without string descriptor support.
Reporting string descriptors is optional to USB devices, and a device
lets us know it can't deal with strings by responding to the LANGID
request with a STALL token.
The kernel handled that correctly before b7af0bb came in, but failed
hard if the LANGID was reported but broken. More than that, if a device
was not able to provide string descriptors, the LANGID was retrieved
over and over again at each string read request.
This patch changes the behaviour so that
a) the LANGID is only queried once
b) devices which can't handle string requests are not asked again
c) devices with malformed LANGID values have a sane fallback to 0x0409
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the original patch I created before David Vrabel posted a better
patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does
basically the same thing. This patch will get replaced with his
(modified) patch later.
Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push
bulk endpoint scatter gather lists down to the host controller drivers.
This allows host controller drivers to more efficiently enqueue these
transfers, and allows the xHCI host controller to better take advantage of
USB 3.0 "bursts" for bulk endpoints.
This patch currently only enables scatter gather lists for bulk endpoints.
Other endpoint types that use the usb_sg_* functions will not have their
scatter gather lists pushed down to the host controller. For periodic
endpoints, we want each scatterlist entry to be a separate transfer.
Eventually, HCDs could parse these scatter-gather lists for periodic
endpoints also. For now, we use the old code and call usb_submit_urb()
for each scatterlist entry.
The caller of usb_sg_init() can request that all bytes in the scatter
gather list be transferred by passing in a length of zero. Handle that
request for a bulk endpoint under xHCI by walking the scatter gather list
and calculating the length. We could let the HCD handle a zero length in
this case, but I'm not sure if the core layers in between will get
confused by this.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally, the USB core had no support for allocating bandwidth when a
particular configuration or alternate setting for an interface was
selected. Instead, the device driver's URB submission would fail if
there was not enough bandwidth for a periodic endpoint. Drivers could
work around this, by using the scatter-gather list API to guarantee
bandwidth.
This patch adds host controller API to allow the USB core to allocate or
deallocate bandwidth for an endpoint. Endpoints are added to or dropped
from a copy of the current schedule by calling add_endpoint() or
drop_endpoint(), and then the schedule is atomically evaluated with a
call to check_bandwidth(). This allows all the endpoints for a new
configuration or alternate setting to be added at the same time that the
endpoints from the old configuration or alt setting are dropped.
Endpoints must be added to the schedule before any URBs are submitted to
them. The HCD must be allowed to reject a new configuration or alt
setting before the control transfer is sent to the device requesting the
change. It may reject the change because there is not enough bandwidth,
not enough internal resources (such as memory on an embedded host
controller), or perhaps even for security reasons in a virtualized
environment.
If the call to check_bandwidth() fails, the USB core must call
reset_bandwidth(). This causes the schedule to be reverted back to the
state it was in just after the last successful check_bandwidth() call.
If the call succeeds, the host controller driver (and hardware) will have
changed its internal state to match the new configuration or alternate
setting. The USB core can then issue a control transfer to the device to
change the configuration or alt setting. This allows the core to test new
configurations or alternate settings before unbinding drivers bound to
interfaces in the old configuration.
WIP:
The USB core must add endpoints from all interfaces in a configuration
to the schedule, because a driver may claim that interface at any time.
A slight optimization might be to add the endpoints to the schedule once
a driver claims that interface. FIXME
This patch does not cover changing alternate settings, but it does
handle a configuration change or de-configuration. FIXME
The code for managing the schedule is currently HCD specific. A generic
scheduling algorithm could be added for host controllers without
built-in scheduling support. For now, if a host controller does not
define the check_bandwidth() function, the call to
usb_hcd_check_bandwidth() will always succeed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1239) updates the kernel's treatment of Unicode. The
character-set conversion routines are well behind the current state of
the Unicode specification: They don't recognize the existence of code
points beyond plane 0 or of surrogate pairs in the UTF-16 encoding.
The old wchar_t 16-bit type is retained because it's still used in
lots of places. This shouldn't cause any new problems; if a
conversion now results in an invalid 16-bit code then before it must
have yielded an undefined code.
Difficult-to-read names like "utf_mbstowcs" are replaced with more
transparent names like "utf8s_to_utf16s" and the ordering of the
parameters is rationalized (buffer lengths come immediate after the
pointers they refer to, and the inputs precede the outputs).
Fortunately the low-level conversion routines are used in only a few
places; the interfaces to the higher-level uni2char and char2uni
methods have been left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the encoding of strings returned by usb_string() from ISO 8859-1
to UTF-8.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an USB hardware does not provide a valid LANGID, fall back to value
zero which is still a reasonable default for most devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
transfer_buffer_length and actual_length have become unsigned, therefore some
additional conversion of local variables, function arguments and print
specifications is desired.
A test for a negative urb->transfer_buffer_length became obsolete; instead
we ensure that it does not exceed INT_MAX. Also, urb->actual_length is always
less than urb->transfer_buffer_length.
rh_string() does no longer return -EPIPE in the case of an unsupported ID.
Instead its only caller, rh_call_control() does the check.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
===================================================================
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1197) fixes an error introduced recently. Since a
significant number of devices can't handle Set-Interface requests, we
no longer call usb_set_interface() when a driver unbinds from an
interface, provided the interface is already in altsetting 0. However
the interface still does get disabled, and the call to
usb_set_interface() was the only thing re-enabling it. Since the
interface doesn't get re-enabled, further attempts to use it fail.
So the patch adds a call to usb_enable_interface() when a driver
unbinds and the interface is in altsetting 0. For this to work
right, the interface's endpoints have to be re-enabled but their
toggles have to be left alone. Therefore an additional argument is
added to usb_enable_endpoint() and usb_enable_interface(), a flag
indicating whether or not the endpoint toggles should be reset.
This is a forward-ported version of a patch which fixes Bugzilla
#12301.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Roka <roka@dawid.hu>
Reported-by: Erik Ekman <erik@kryo.se>
Tested-by: Erik Ekman <erik@kryo.se>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1195) eliminates a potential problem identified by
Oliver Neukum. When a driver queues an asynchronous Set-Config
request using usb_driver_set_configuration(), the request should be
cancelled if userspace changes the configuration first. The patch
introduces a linked list of pending async Set-Config requests, and
uses it to invalidate the requests for a particular device whenever
that device's configuration is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1185) makes usbcore take advantage of the bus
notifications sent out by the driver core. Now we can create all our
device and interface attribute files before the device or interface
uevent is broadcast.
A side effect is that we no longer create the endpoint "pseudo"
devices at the same time as a device or interface is registered -- it
seems like a bad idea to try registering an endpoint before the
registration of its parent is complete. So the routines for creating
and removing endpoint devices have been split out and renamed, and
they are called explicitly when needed. A new bitflag is used for
keeping track of whether or not the interface's endpoint devices have
been created, since (just as with the interface attributes) they vary
with the altsetting and hence can be changed at random times.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a new call to be able to do a USB reset from an
atomic contect. This is quite helpful in USB callbacks to handle
errors (when the only thing that can be done is to do a device
reset).
It is done queuing a work struct that will do the actual reset. The
struct is "attached" to an interface so pending requests from an
interface are removed when said interface is unbound from the driver.
The call flow then becomes:
usb_queue_reset_device()
__usb_queue_reset_device() [workqueue]
usb_reset_device()
usb_probe_interface()
usb_cancel_queue_reset() [error path]
usb_unbind_interface()
usb_cancel_queue_reset()
usb_driver_release_interface()
usb_cancel_queue_reset()
Note usb_cancel_queue_reset() needs smarts to try not to unqueue when
it is actually being executed. This happens when we run the reset from
the workqueue: usb_reset_device() is called and on interface unbind
time, usb_cancel_queue_reset() would be called. That would deadlock on
cancel_work_sync(). To avoid that, we set (before running
usb_reset_device()) usb_intf->reset_running and clear it inmediately
after returning.
Patch is against 2.6.28-rc2 and depends on
http://marc.info/?l=linux-usb&m=122581634925308&w=2 (as submitted by
Alan Stern).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no need to take the address of the function params or local variables
when the direct value byteswapping routines are available.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1155) fixes a bug in usbcore. When interfaces are
deleted, either because the device was disconnected or because of a
configuration change, the extra attribute files and child endpoint
devices may get left behind. This is because the core removes them
before calling device_del(). But during device_del(), after the
driver is unbound the core will reinstall altsetting 0 and recreate
those extra attributes and children.
The patch prevents this by adding a flag to record when the interface
is in the midst of being unregistered. When the flag is set, the
attribute files and child devices will not be created.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27, 2.6.26, 2.6.25]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, I found the cause of the hang. It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.
This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is the usb interface driver probe() methods that
can't call usb_set_configuration, not usb device driver.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern