- Delete global_phy due to we can get the phy from phy layer now
- using devm_usb_get_phy to instead of usb_get_phy
- delete the otg_set_peripheral, which should be handled by otg layer
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY operations are common, so move them to core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CI_HDRC_REGS_SHARED stands for the controller registers is shared
with other USB drivers, if all USB drivers are at chipidea/, it doesn't
needed to be set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This
flag doesn't need to be set if the vbus is always on for gadget
since dp has always pulled up after the gadget has initialized.
So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if
it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to
shared register.
- When the gadget starts (load one gadget module), the controller
can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not
relate to shared register.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc)
to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to
indicate it is an id interrupt or a vbus interrupt.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The role's init will be called at probe procedure.
- The role's destroy will be called at fail patch
at probe and driver's removal.
- The role's start/stop will be called when specific
role has started.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since someone has added camelcase detection to checkpatch.pl, chipidea
udc patches have been very noisy. To make everybody's life easier, this
patch changes camelcase names into something more appropriate to the
coding style. No functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the restriction of having a limited amount of only
four active tds on one endpoint. We use the linked list implementation
to manage all tds which get added and removed by hardware_{en,de}queue.
The removal of this restriction adds the driver to run into a hardware
errata. It's possible that the hardware will still address an transfer
descriptor that already got cleaned up. To solve this the patch also
postpone the cleanup of processed tds by one.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having a limited number of usable tds in the udc we use a
linked list to support dynamic amount of needed tds for all special
gadget types. This improves throughput.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds iso endpoint support to the device controller.
It makes use of the multiplication bits in the maxpacket field
of the endpoint and calculates the multiplier bits for each
transfer description on every request.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usb phy code does return ERR_PTR() values, make sure that we don't
end up dereferencing them. This is a problem, for example, on platforms
that don't register a phy for chipidea since b7fa5c2a ("usb: phy: return
-ENXIO when PHY layer isn't enabled").
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A static count of transfer descriptors was used everywhere in the driver
with the fixed number 5. This patch adds a define, named TD_PAGE_COUNT,
and replaces all users of this value. This way its possible to have only
one parameter to change and limit the amount of buffer pointers per TD.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call ep_queue unlocked inside the own driver. We
move its functionionality into an unlocked version.
This patch removes potential unlocked timeslots inside
isr_setup_status_phase and isr_get_status_response, in which the lock
got released just before acquired again inside usb_ep_queue.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not safe to truncate requests to the maximum possible size the
controller can handle with one td and to keep working. That patch fixes
that with proper error handling instead.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the read of the td status to one atomic operation to
analyse coherent bits.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Alex: fixed backwards endianness conversion]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its not necessary and also not specified in the datasheet to change the
ZLT flag before every ep_prime. This patch moves this to the ep_enable
and applies it only for non configuration endpoints.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reworks the cap value from several read
and write operations to one single operation.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
[Alex: removed useless isoc-related bit of code]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet of the synopsys core describes only to overwrite the
active and halted bits in the qhead before priming any endpoint.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
[Alex: fixed a case of line-too-long]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert between big-endian and little-endian format when accessing the usb
controller structures which are little-endian by specification.
Fix cases where the little-endian memory layout is taken for granted.
The patch doesn't have any effect on the already supported little-endian
architectures.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
[Alex: minor cosmetic fixes]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chipidea's ffs_nr() is pretty much what __ffs() does.
Use that one instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[rebased on top of debug infrastructure rework]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create and remove debugfs entries in hdrc probe/remove instead of
start/stop of the device controller. Gadget specific will not export
anything while the controller is in host mode.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we have a bunch of files in sysfs that display all sorts of
debugging information for the device controller, so they have to move to
debugfs where they belong. The "registers" interface have been removed,
since it doesn't fit into the current driver design as is and it's hardly
a good idea to touch the registers from userspace anyway.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the legacy from the original driver design, we retain home-grown
tracing infrastructure, complete with own ring buffer and timestamps,
which among other things has a performance penalty. This patch removes it.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several problems with this patch:
+ in introduces a sparse warning for a condition that's always negative,
+ and because of that, it actually doesn't do anything useful,
+ and vbus detection belongs to otg, not device function anyway.
This reverts commit 8c4fc03195.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
[Alex: amended the above text]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some headers included in udc core code are not actually needed, remove
them and add irqreturn.h, which was implicitly included via irq.h.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.
Let's remove every history of it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using vbus valid interrupt to detect vbus.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>