Do not forget to program the MCLK ratio for the I2S output.
Otherwise, the master clock frequency can be too high for
the DACs at sample frequencies above 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When resuming, we better take the DACs out of the reset state before
trying to use them.
Reference: kernel bug #13599http://bugzilla.kernel.org/show_bug.cgi?id=13599
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone input and its volume register have only one channel, so
we have to make the corresponding mixer control a mono control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar Essence ST and its daughterboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar HDAV1.3 has a digital input jack, so enable the corresponding
device.
This is not related to the HDMI stuff, which stays unsupported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another PCI ID for a second revision of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM stream is closed, flush the corresponding DMA channel.
Otherwise, the DMA controller would continue to output the last sample
which would result in a DC offset on the output.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the HT-Omega Claro (halo) sound cards, the headphone amplifier must
be enabled explicitly by setting a GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Model drivers assume that model_data is zeroed, so we better use
kzalloc() (like we did before when it was allocated together with the
card structure).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use -60 dB as the minimum value of the master volume mixer control.
While the DACs would support ranges down to about -120 dB, such
attenuations are not useful in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HT-Omega Claro halo's ADC is an AK5385 instead of a WM8785, so we
should handle the ADC parameters as we do with the X-Meridian.
Using the code for the wrong ADC does not seem to have any audible
effects, and the Windows driver does it, but it is nonetheless a good
idea to run the AK5385 with an oversampling ratio that is not outside
the documented limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the EEPROM was partially overwritten (which seems to happen before the OS is
booted), restore its entire contents by deducing it from the remaining
information.
This does not have any effect on the Linux driver, which works even with
incomplete information in the EEPROM, but it makes other drivers work again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten. When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers. Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.
Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter. The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When allocating resources, use a fixed name instead of reading it from
the model structure. This allows us to allocate the resources before
the actual model is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the model-specific data dynamically instead of including it in
the memory block of the card structure. This will allow us to determine
the actual model after the card creation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model. Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7e86c0e685 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.
More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect. In other words, the presence of this
driver does not have any effect on the occurrence of the error. (So
far, the available evidence seems to point to a BIOS bug.)
Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.
The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This hardware has a better chance of working correctly if we don't
forget to enable it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Asus Xonar D2 and D2X models, the SPI chip select signal for the
fourth DAC shares its pin with the serial clock for the EEPROM that
contains the PCI subdevice ID values. It appears that when DAC
registers are written and some other unknown conditions occur (probably
noise on the EEPROM's chip select line), the EEPROM gets overwritten
with garbage, which makes it impossible to properly detect the card
later.
Therefore, we better avoid DAC register writes and make sure that the
driver works with the DAC's registers' default values. Consequently,
the sample format is now I2S instead of left-justified (no user-visible
change), and the DAC's volume/mute registers cannot be used anymore
(volume changes are now done by the software volume plugin).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After sending a reset command to the UART, wait some time for the ACK to
be generated (and to be read and dropped by the interrupt handler)
before sending the next command.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the first PCM device from "Analog" to "Multichannel" because it
can be used for HDMI output on the Xonar HDAV.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the callback function that switches between line and mic inputs
on the Xonar D1 because it is also usable on other models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Do not use a hardcoded number when iterating over the PCM1796 DACs to
allow for cards with a different number of analog output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce some trivial functions to better document the relationships of
the various model callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add functions to allow model drivers to communicate with external chips
by doing I/O with the not-used-for-MIDI UART.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags. This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Factor out the common code of the mixer callbacks that handle controls
that just switch a single GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The Xonar D2X and DX are very similar to the D2 and D1, respectively, so
we can handle the differences dynamically instead of using a separate
model structure for each one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Handle the differences between the X-Meridian and the other models in
the probe callback instead of using a second model structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce symbols that indicate the two models handled by the snd-oxygen
driver, instead of using a magic number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Put a copy of the model structure into the chip structure so that model-
specific drivers can modify it depending on a particular device
instance.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When setting the SPDIF channel status sample rate field, use the
recently defined symbols instead of magic numbers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar DX does not have CD Capture controls, so we have to check that
a control actually exists before muting it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a constraint for the period time so that there are less than ten
seconds between interrupts so that ALSA does not assume that the device
is dead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduce symbols for the buffer/period size constraints so that their
limits and relationships become clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the setting of the output enable GPIO bit to a separate function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Create separate functions for the code that initializes the hardware, as
opposed to initializing internal driver state, so that they can be
reused for resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When initializing the DAC volume registers, we can just use the generic
volume update functions instead of setting the registers manually.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Save the written values of all CMI8788 and AC97 registers and of some of
the DAC/ADC registers so that it is possible to restore the register
state later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove another magic number - add a symbol for the size of the PCI I/O
range.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check that model->control_filter is set before trying to call it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a pointer for DAC volume TLV data to the model structure so that the
model driver do not need to manually assign it in their control filter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add fields for the DAC volume limits to the module structure so that
model drivers do not need to install their own control info handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The empty hifier_mixer_init() function is useless; remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the GPIO 1 mixer control to enable I/O through the front panel
connector of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Xonar DX, initialize all bits of the two-wire control register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control for switching whatever it is that is connected to
GPIO pin 1 on the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the card model does not have a digital input or an AC97 codec,
disable the respective interrupt and mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When selecting the capture source on the Xonar DX, the input jack must
be routed to either the line input or the microphone input by setting a
GPIO pin. This requires an additional callback so that the model driver
can hook into the toggling of AC97 switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the card short name to show to show the card name instead of the
chip name.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When playing data at 96 kHz or higher, reduce the DAC oversampling rate
to 32.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the code that is common to all Xonar models to a separate function,
and make it more generic in preparation for another model.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename all CS5381 symbols to CS53x1 because they can also be used for
Xonar models with a CS5361.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use separate model structures for the D2 and D2X so that the init
function does not have to check for the model again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disable the master clock outputs of any unused I2S inputs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When specifying which PCM devices to use, model drivers now use flags
that also specify the routing between PCM devices and DMA channels
instead of just DMA channel bits. This simplifies some code that checks
for these flags.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add controls to enable monitoring of the analog and digital inputs.
To allow monitoring after loading the driver when nothing has been
played back or recorded yet, the I2S input and outputs are initialized
to a valid configuration.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the PCM1796 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the WM8786 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use priv_idx as an identifier.
sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one
sound/pci/oxygen/virtuoso.c:56:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GPIO pin 0 of the CM9780 must be set when muting the line input even
on non-Xonar cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed invalid __devinit and __devexit that are remaining after
split to a helper module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While the AK4396 and WM8785 datasheets say that the SPI clock cycle
length must be at least 200 ns, 320 ns seems not to work reliably with
the controller, so we better use 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
On the Xonar D2X, monitor the GPIO pin that indicates whether external
power is present.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When a second AC97 codec is present, add a PCM device for capturing from
the front panel.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After an AC97 register read or write, use the AC97 interrupt instead of
polling to wait for the access to be completed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the line input switching code to the Virtuoso driver because only
the Xonar cards bypass the analog mixer for line input.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the upper sample rate limit for the double rate mode of the AK4396
to the value from the datasheet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a driver for the MediaTek/TempoTec HiFier Fantasia sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Initialize more registers of the controller and the second AC97 codec.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a field to struct oxygen_model to allow model drivers for cards with
less than eight output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
None of the reference design models have MIDI, only the X-Meridian
allows to connect a MIDI adapter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix up SPDIF input sample rates again: 32 kHz and 64 kHz are not
supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a mixer control for the SPDIF loopback function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add one more indirection to the lookup of the snd_pcm_hardware
structures so that we can save the space of the duplicate ones.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected. This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix some wrong values for the definitions of the source masks for DACS 1
and 3.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Actually use the template that was maybe changed by the control filter
instead of the original one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
According to the datasheets, the SPI clock cycle must be at least 200 ns
for the AK4396 and the WM8785, so we cannot use the default 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow to record with 32 kHz, 64 kHz, 88.2 kHz and 176.4 kHz with cards
that have a WM8785 ADC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add symbol definitions for the various codecs and GPIO pins.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port. Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the DMA_PAUSE register for pausing instead of stopping DMA.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The default playback routing must be 0xe4, not 0xe1; the front and
surround DACs were exchanged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add more symbols for registers and register fields.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add proper register bit symbols for the I2S format field, and allow card
models to configure the I2S format to be used for the DACs and ADCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a callback to the model structure to allow modification of the
hardware PCM limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the models to modify mixer controls before they are added to the
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the card models to specify whether each of the hardware DMA
channels is used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Only initialize and create mixer controls for the first AC97 codec when
one has actually been detected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename the 'PCM Playback Volume'/'Switch' mixer controls to 'Master'.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The line input cannot be mixed with the other inputs, so we have to mute
the other input switches when it is selected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use an array for the pointers to known controls so that it is easier to
add more.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do not exchange the surround and back jacks except when in 7.1 mode
where the surround jack is not rear but side.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When we store the DMA channel number in the substream's private_data
pointer, use uintptr_t as an intermediate step when casting from/to
unsigned int to prevent the compiler from whining when the pointer size
is different.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the snd-virtuoso driver for the Asus Virtuoso 200 chip used on the
PCI and PCI-E models of the Xonar sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the snd-oxygen driver for the C-Media CMI8788 (Oxygen) chip, used on
the Asound A-8788, AuzenTech X-Meridian, Bgears b-Enspirer,
Club3D Theatron DTS, HT-Omega Claro, Razer Barracuda AC-1,
Sondigo Inferno, and TempoTec HIFIER sound cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch