With the introduction of WM8960_SYSCLK_AUTO mode, WM8960_SYSCLK_PLL mode was
made unusable. Ensure we're not PLL mode before trying to use MCLK.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
INBMIX1 controls LINPUTs and INBMIX2 controls RINPUTs, so fix the naming
accordingly.
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/RINPUT1 can line to Left/Right Boost Mixer through boost switch.
If boost switch is open, there will be no voice when using L/RINPUT1.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In normal operation, the left and right channel digital audio data is
converted to analogue in two separate DACs. There is a mono-mix mode
where the two audio channels are mixed together digitally and then
converted to analogue using only one DAC, while the other DAC is
switched off. The mono-mix signal can be selected to appear on both
analogue output channels. The mono mix is automatically attenuated by
6dB to prevent clipping.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the xinvert value from 0 to 1 on the "Capture Switch" control
WM8960 datasheet is shown as follows:
Bit 7 at 00h and 01h register address
1 : Enable Mute, 0 : Disable Mute
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only accept "deemph" values of zero and one, but by mistake we
accept negatives as well. It's harmless but let's clean it up anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the max register value of mic boost pga should be 3.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input PGAs have a gain range from -17.25dB to +30dB in 0.75dB steps.
The boost stage can provide additional gain. For line inputs, -12dB to
+6dB gain is available on the boost mixer. For micphone inputs, it can
provide up to +29dB additional gain from the microphone PGA.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min gain is the corresponding gain value when the register value is 0
instead of 1, just correct it.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sysclk auto mode. When it's sysclk auto mode, if the MCLK is
available for clock configure, using MCLK to provide sysclk directly,
otherwise, search a available pll out frequcncy and set pll.
Configure clock in hw_params may cause problems when using bypass style
paths without hw_params in machine driver getting called. So add configure
clock to set_bias_level.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
the enum of "DAC Polarity" should be wm8960_enum[1].
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and replace all
other manual access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to referance manual, right justify mode can't
support 32 bit word length.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec driver missing configure its bit clock and frame clock for codec
master mode, so add support for it. It will calculate a appropriate frequency
dividing ratio according to the system clock, bit clock and frame clock, then
set the corresponding registers.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It should be "RINPUT3" instead of "LINPUT3" route to "Right Input
Mixer".
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
When we want to use wm8960 codec, we should enable its MCLK in machine driver.
It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition
away from ON. In this case, disable the codec mclk. When current bias_level
is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case,
enable the codec mclk.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the device tree binding for the WM8960 codec, and modify the
driver to extract the platform data from device tree, if present.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CODEC doesn't care how data is laid out in memory.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Both the snd_soc_codec and snd_soc_platform struct do have a pointer to the
parent card and both handle this pointer in mostly the same way. This patch
moves the card field to the component level which will allow further code
consolidation between platforms and CODECS.
Since there are only a handful of users of the snd_soc_codec struct's card field
(and none of the snd_soc_platform's) these are update in this patch as well,
which allows it to be removed from the snd_soc_codec struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Bit 9 of PLL2,3 and 4 is reserved as '0'. The 24bit fractional part
should be split across each register in 8bit chunks.
Signed-off-by: Mike Dyer <mike.dyer@md-soft.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler. There was no explicit
regmap_exit call in this function which was probably a bug.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'dres' field (discharge resistance for headphone outputs) is no longer
used in the driver, so remove it.
It was used in the original version of the driver when entering standby
from off, but we stopped using it when we switched from having a single
startup sequence to having separate cap and capless sequences.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown