Use max_t() instead of max(resource_size_t,) in order to fix
the following checkpatch warning.
WARNING: max() should probably be max_t(resource_size_t, SZ_64K, size)
WARNING: max() should probably be max_t(resource_size_t, SZ_1M, size)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The mvebu PCI host controller driver uses an emulated PCI-to-PCI bridge to
leverage the core PCI kernel enumeration logic to dynamically create and
remove the MBus windows needed to access the memory and I/O regions of each
PCI interface.
In the context of this PCI-to-PCI bridge emulation, the driver emulates
all reads and writes to the PCI bridge registers. Upon a write to the
registers configuring the I/O base and limit, the driver was creating the
MBus window and calling pci_ioremap_io() to setup the mapping.
However, it turns out that accesses to these registers are made in an IRQ
disabled context, while pci_ioremap_io() is a potentially sleeping
function. Not only this is wrong, but it is causing fairly loud warnings
at boot time when the appropriate kernel hacking options are enabled.
This patch solves this by moving the pci_ioremap_io() call to the startup
of the driver. At this point, we don't know how many PCI interfaces will
be enabled, so we are simply remapping the entire PCI I/O space to virtual
addresses. This is reasonable since this I/O space is limited to 1 MB in
size, and also because the MBus windows continue to be created in a dynamic
fashion only when devices need them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit d2e5f0c16a (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.
Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them. The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.
Fixes: d2e5f0c16a (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021
Reported-and-tested-by: Agustin Barto <abarto@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
* pci/host-imx6:
PCI: imx6: Fix bugs in PCIe startup code
PCI: imx6: Start link in Gen1 before negotiating for Gen2 mode
PCI: imx6: Factor out link up wait loop
PCI: imx6: Factor out PHY reset
PCI: imx6: Report "link up" only after link training completes
PCI: imx6: Make reset-gpio optional
Make pci_enable_msi_block(), pci_enable_msi_block_auto() and
pci_enable_msix() consistent with regard to the type of 'nvec' argument.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
If populate_msi_sysfs() function failed msix_capability_init() must return
the error code, but it returns the success instead. This update fixes the
described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
pp->io_base, which is the input of the outbound IO address translation
unit, should be the CPU address. It was incorrectly programmed to the
realio address.
We should pass global_io_offset rather than sys->io_offset to
pci_ioremap_io(), so we map the new window into the first available spot in
the Linux view of the I/O space.
We must also pass CPU address instead of realio address to pci_ioremap_io().
This patch fixes above issue. It has been tested with Lecroy PTC in AIC
mode and Pericom PI7C9X2G303EL PCIe switch, which does not work otherwise.
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Zhu <Hong-Xing.Zhu@freescale.com>
The cfg_read/write functions are DesignWare-specific. Add dw_pcie prefix
to avoid collision in global name space.
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
The interrupts were cleared after the IRQ handler was called. This means
that new interrupts that occur after the handler handled the previous IRQ
but before the interrupt is cleared will be missed.
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Matthias Mann <m.mann@arkona-technologies.de>
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Richard Zhu <hong-xing.zhu@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Sean Cross <xobs@kosagi.com>
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
└── 40
└── mode
New MSI attributes:
pci_device
└── msi_irqs
└── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Previously pcie_device_init() called get_device() if device_register() for
the new pcie_device succeeded, and remove_iter() called put_device() when
removing before unregistering the device.
But device_register() already increments the reference count in
device_add(), so we don't need to do it again here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is required so that we give up the last reference to the device.
Removed the kfree() as put_device will result in release_pcie_device()
being called and hence the container of the device will be kfree'd.
[bhelgaas: fix conflict after my previous cleanup]
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the straightline path the normal no-error path. Check for errors and
return them directly, instead of checking for success and putting the
normal path in an "if" body.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
mvebu_pcie_of_match_table is always compiled in. Hence of_match_ptr is not
required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch first forces the link into Gen1 mode before starting up the link
and, only after the link is up, start negotiating possible Gen2 mode
operation. This is because without such sequence, some PCIe switches are
not detected at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Split the function that waits for the PCIe link to come up from the rest if
the host init function. We will find this change useful in the subsequent
patch, since this will be called twice then.
No functional change.
[bhelgaas: remove useless "return;"]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Split the PCIe PHY reset from the link up function to make the code a
little more structured.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
While waiting for the PHY to report the PCIe link is up, we might hit a
situation where the link training is still in progress, while the PHY
already reports the link is up. Add additional check for this condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Some boards do not have a PCIe reset GPIO. To avoid probe failure on these
boards, make the reset GPIO optional as well.
[bhelgaas: whitespace fixes]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
* pci/vc:
PCI: Rename PCI_VC_PORT_REG1/2 to PCI_VC_PORT_CAP1/2
PCI: Add Virtual Channel to save/restore support
PCI: Add support for save/restore of extended capabilities
PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
* pci/host-mvebu:
PCI: mvebu: Remove duplicate of_clk_get_by_name() call
PCI: mvebu: Support a bridge with no IO port window
PCI: mvebu: Obey bridge PCI_COMMAND_MEM and PCI_COMMAND_IO bits
PCI: mvebu: Drop writes to bridge Secondary Status register
* pci/deletion:
PCI: Remove from bus_list and release resources in pci_release_dev()
PCI: Move pci_proc_attach_device() to pci_bus_add_device()
PCI: Use device_release_driver() in pci_stop_root_bus()
PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
Conflicts:
drivers/pci/remove.c
Previously we removed the pci_dev from the bus_list and released its
resources in pci_destroy_dev(). But that's too early: it's possible to
call pci_destroy_dev() twice for the same device (e.g., via sysfs), and
that will cause an oops when we try to remove it from bus_list the second
time.
We should remove it from the bus_list only when the last reference to the
pci_dev has been released, i.e., in pci_release_dev().
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
4f535093cf ("PCI: Put pci_dev in device tree as early as possible")
moved pci_proc_attach_device() from pci_bus_add_device() to
pci_device_add().
This moves it back to pci_bus_add_device(), essentially reverting that
part of 4f535093cf. This makes it symmetric with pci_stop_dev(),
where we call pci_proc_detach_device() and pci_remove_sysfs_dev_files()
and set dev->is_added = 0.
[bhelgaas: changelog, create sysfs then attach proc for symmetry]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be consistent with 4bff674990 ("PCI: Move device_del() from
pci_stop_dev() to pci_destroy_dev()", this changes pci_stop_root_bus()
to use device_release_driver() instead of device_del().
This also changes pci_remove_root_bus() to use device_unregister()
instead of put_device() so it corresponds with the device_register()
call in pci_create_root_bus().
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
I'm seeing traces analogous to the one below in Thunderbolt testing:
WARNING: CPU: 3 PID: 76 at /scratch/rafael/work/linux-pm/fs/sysfs/group.c:214 sysfs_remove_group+0x59/0xe0()
sysfs group ffffffff81c6c500 not found for kobject '0000:08'
Modules linked in: ...
CPU: 3 PID: 76 Comm: kworker/u16:7 Not tainted 3.13.0-rc1+ #76
Hardware name: Acer Aspire S5-391/Venus , BIOS V1.02 05/29/2012
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801644b9ac8 ffffffff816b23bf 0000000000000007
ffff8801644b9b18 ffff8801644b9b08 ffffffff81046607 ffff88016925b800
0000000000000000 ffffffff81c6c500 ffff88016924f928 ffff88016924f800
Call Trace:
[<ffffffff816b23bf>] dump_stack+0x4e/0x71
[<ffffffff81046607>] warn_slowpath_common+0x87/0xb0
[<ffffffff810466d1>] warn_slowpath_fmt+0x41/0x50
[<ffffffff811e42ef>] ? sysfs_get_dirent_ns+0x6f/0x80
[<ffffffff811e5389>] sysfs_remove_group+0x59/0xe0
[<ffffffff8149f00b>] dpm_sysfs_remove+0x3b/0x50
[<ffffffff81495818>] device_del+0x58/0x1c0
[<ffffffff814959c8>] device_unregister+0x48/0x60
[<ffffffff813254fe>] pci_remove_bus+0x6e/0x80
[<ffffffff81325548>] pci_remove_bus_device+0x38/0x110
[<ffffffff8132555d>] pci_remove_bus_device+0x4d/0x110
[<ffffffff81325639>] pci_stop_and_remove_bus_device+0x19/0x20
[<ffffffff813418d0>] disable_slot+0x20/0xe0
[<ffffffff81341a38>] acpiphp_check_bridge+0xa8/0xd0
[<ffffffff813427ad>] hotplug_event+0x17d/0x220
[<ffffffff81342880>] hotplug_event_work+0x30/0x70
[<ffffffff8136d665>] acpi_hotplug_work_fn+0x18/0x24
[<ffffffff81061331>] process_one_work+0x261/0x450
[<ffffffff81061a7e>] worker_thread+0x21e/0x370
[<ffffffff81061860>] ? rescuer_thread+0x300/0x300
[<ffffffff81068342>] kthread+0xd2/0xe0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
[<ffffffff816c19bc>] ret_from_fork+0x7c/0xb0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
(Mika Westerberg sees them too in his tests).
Some investigation documented in kernel bug #65281 led me to the
conclusion that the source of the problem is the device_del() in
pci_stop_dev() as it now causes the sysfs directory of the device to be
removed recursively along with all of its subdirectories. That includes
the sysfs directory of the device's subordinate bus (dev->subordinate) and
its "power" group.
Consequently, when pci_remove_bus() is called for dev->subordinate in
pci_remove_bus_device(), it calls device_unregister(&bus->dev), but at this
point the sysfs directory of bus->dev doesn't exist any more and its
"power" group doesn't exist either. Thus, when dpm_sysfs_remove() called
from device_del() tries to remove that group, it triggers the above
warning.
That indicates a logical mistake in the design of
pci_stop_and_remove_bus_device(), which causes bus device objects to be
left behind their parents (bridge device objects) and can be fixed by
moving the device_del() from pci_stop_dev() into pci_destroy_dev(), so
pci_remove_bus() can be called for the device's subordinate bus before the
device itself is unregistered from the hierarchy. Still, the driver, if
any, should be detached from the device in pci_stop_dev(), so use
device_release_driver() directly from there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281#c6
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These are set of two capability registers, it's pretty much given that
they're registers, so reflect their purpose in the name.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
While we don't really have any infrastructure for making use of VC
support, the system BIOS can configure the topology to non-default
VC values prior to boot. This may be due to silicon bugs, desire to
reserve traffic classes, or perhaps just BIOS bugs. When we reset
devices, the VC configuration may return to default values, which can
be incompatible with devices upstream. For instance, Nvidia GRID
cards provide a PCIe switch and some number of GPUs, all supporting
VC. The power-on default for VC is to support TC0-7 across VC0,
however some platforms will only enable TC0/VC0 mapping across the
topology. When we do a secondary bus reset on the downstream switch
port, the GPU is reset to a TC0-7/VC0 mapping while the opposite end
of the link only enables TC0/VC0. If the GPU attempts to use TC1-7,
it fails.
This patch attempts to provide complete support for VC save/restore,
even beyond the minimally required use case above. This includes
save/restore and reload of the arbitration table, save/restore and
reload of the port arbitration tables, and re-enabling of the
channels for VC, VC9, and MFVC capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Current save/restore is specific to standard capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We currently have two instance of this loop which waits for a pending bit
to clear in a status dword. Generalize the function for future users.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, the caller checked ATTN_LED() or PWR_LED() to see whether the
slot has indicators before setting the indicator state. That clutters the
caller unnecessarily, so this moves the test inside the callees. The test
may not even be necessary; per spec it should be harmless to try to turn on
a non-existent LED. But checking first does avoid unnecessary hotplug
commands.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add symbolic constants for the PCIe Slot Control indicator and power
control fields defined by spec and use them instead of open-coded hex
constants.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's simpler to test the PCI_EXP_SLTSTA_PFD bit directly and to write the
constant back to PCI_EXP_SLTSTA.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already have the vendor/device IDs from pci_setup_device(), so drop that
info and print things that will be more useful for debugging: the slot
number and presence of button/indicators/link active reporting/etc.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These functions:
pcie_enable_notification()
pciehp_power_off_slot()
pciehp_get_power_status()
pciehp_get_attention_status()
pciehp_set_attention_status()
pciehp_get_latch_status()
pciehp_get_adapter_status()
pcie_write_cmd()
now always return success, so this patch makes them void and drops the
error-checking code in their callers.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There's not much point in checking the return value from every config space
access because the only likely errors are design-time things like unaligned
accesses or invalid register numbers. The checking clutters the code
significantly, so this patch removes it.
No functional change.
Reference: http://lkml.kernel.org/r/CA+55aFzP4xEbcNmZ+MS0SQ3LrULzSq+dBiT_X9U-bPpR-Ukgrw@mail.gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
The pciehp_readw() and pciehp_writew() wrappers only look up the pci_dev
and call the PCIe Capability accessors, so we can make things a little
more straightforward by just using the PCIe Capability accessors directly.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_hest_parse() and aer_hest_parse_aff() are almost identical. We use
aer_hest_parse() to check the ACPI_HEST_FIRMWARE_FIRST flag for a specific
device, and we use aer_hest_parse_aff() to check to see if any device sets
the flag.
This drops aer_hest_parse_aff() and enhances aer_hest_parse() so it
collects the union of the PCIe ACPI_HEST_FIRMWARE_FIRST flag settings when
no specific device is supplied.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Betty Dall <betty.dall@hp.com>
aer_set_firmware_first() searches the HEST for an error source descriptor
matching the specified PCI device. It uses the apei_hest_parse() iterator
to call aer_hest_parse() for every descriptor in the HEST.
Previously, aer_hest_parse() incorrectly assumed every descriptor was for a
PCIe error source. This patch adds a check to avoid that error.
[bhelgaas: factor check into helper, use in aer_hest_parse_aff(), changelog]
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save one indentation level in aer_print_error() for the generic case where
we have info->status of an error, disregard 80 cols rule a bit for the sake
of better readability, fix alignment.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and call it instead of duplicating the large printk format
statement.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/yijing-dev_is_pci:
alpha/PCI: Use dev_is_pci() to identify PCI devices
arm/PCI: Use dev_is_pci() to identify PCI devices
arm/PCI: Use dev_is_pci() to identify PCI devices
parisc/PCI: Use dev_is_pci() to identify PCI devices
sparc/PCI: Use dev_is_pci() to identify PCI devices
ia64/PCI: Use dev_is_pci() to identify PCI devices
x86/PCI: Use dev_is_pci() to identify PCI devices
PCI: Use dev_is_pci() to identify PCI devices
* pci/misc:
PCI: Stop clearing bridge Secondary Status when setting up I/O aperture
PCI: Prevent bus conflicts while checking for bridge apertures
PCI: Drop "irq" param from *_restore_msi_irqs()
PCI/portdrv: Remove superfluous name cast
PCI: Clear NumVFs when disabling SR-IOV in sriov_init()
pci_setup_bridge_io() accessed PCI_IO_BASE and PCI_IO_LIMIT using dword
(32-bit) reads and writes, which also access the Secondary Status register.
Since the Secondary Status register is in the upper 16 bits of the dword,
and we preserved those upper 16 bits, this had the effect of clearing any
of the write-1-to-clear bits that happened to be set in the Secondary
Status register.
That's not what we want, so use word (16-bit) accesses to update only
PCI_IO_BASE and PCI_IO_LIMIT.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bridge_check_ranges() determines whether the bridge supports an I/O
aperture and a prefetchable memory aperture.
Previously, if the I/O aperture was unsupported, disabled, or configured at
[io 0x0000-0x0fff], we wrote 0xf0 to PCI_IO_BASE and PCI_IO_LIMIT, which,
if the bridge supports it, enables the I/O aperture at [io 0xf000-0xffff].
The enabled aperture may conflict with other devices in the system.
Similarly, we wrote 0xfff0 to PCI_PREF_MEMORY_BASE and
PCI_PREF_MEMORY_LIMIT, which enables the prefetchable memory aperture at
[mem 0xfff00000-0xffffffff], and that may also conflict with other devices.
All we need to know is whether the base and limit registers are writable,
so we can use values that leave the apertures disabled, e.g., PCI_IO_BASE =
0xf0, PCI_IO_LIMIT = 0xe0, PCI_PREF_MEMORY_BASE = 0xfff0,
PCI_PREF_MEMORY_LIMIT = 0xffe0.
Writing non-zero values to both the base and limit registers means we
detect whether either or both are writable, as we did before.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Based-on-patch-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Change x86_msi.restore_msi_irqs(struct pci_dev *dev, int irq) to
x86_msi.restore_msi_irqs(struct pci_dev *dev).
restore_msi_irqs() restores multiple MSI-X IRQs, so param 'int irq' is
unneeded. This makes code more consistent between vm and bare metal.
Dom0 MSI-X restore code can also be optimized as XEN only has a hypercall
to restore all MSI-X vectors at one time.
Tested-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
The old Tegra-specific API used a struct clock to represent the module
to reset. Some of the clocks retrieved during probe() were only used for
reset purposes, and indeed aren't even true clocks. So, there's no need
to get() them any more.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Use dev_is_pci() instead of checking bus type directly.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Probably due to a merge conflict resolution gone bad, the PCI clock is
got twice. Remove the redundant call of of_clk_get_by_name().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
If runtime PM is enabled in the kernel config, the PCI clocks are not
forced on at start-up, and thus, are never enabled. Use
pm_runtime_get_sync() to enable the clocks.
While at it, use dev_info() instead of pr_info() since now we have the
device pointer available in the PCI setup callback.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is no need to use 'goto err' as we can directly return the errors.
No functional change.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
write_msi_msg() does exactly the same so there is no need to explicitly
call pci_write_config_word() and do the same twice.
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjørn Erik Nilsen <ben@datarespons.no>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
904d0e7889 ("PCI: designware: Add irq_create_mapping()") resulted in
pre-allocated irq descs. Problem was that in assign_irq() these descs were
explicitly allocated and hence also freed, resulting in a crash. We also
need to clear the entire irq range in teardown. With this commit the
teardown basically does exactly the opposite of what was done in setup.
The crash this fixes looks like:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
PC is at dw_msi_teardown_irq+0x40/0x118
LR is at trace_hardirqs_on_caller+0xf4/0x1c0
Backtrace:
[<802c401c>] (dw_msi_teardown_irq+0x0/0x118) from [<802c1844>] (arch_teardown_msi_irq+0x3c/0x40)
[<802c1808>] (arch_teardown_msi_irq+0x0/0x40) from [<802c1a08>] (default_teardown_msi_irqs+0x68/0x84)
[<802c19a0>] (default_teardown_msi_irqs+0x0/0x84) from [<802c1a34>] (arch_teardown_msi_irqs+0x10/0x14)
[<802c1a24>] (arch_teardown_msi_irqs+0x0/0x14) from [<802c1ad0>] (free_msi_irqs+0x98/0x144)
[<802c1a38>] (free_msi_irqs+0x0/0x144) from [<802c2570>] (pci_disable_msi+0x48/0x60)
[<802c2528>] (pci_disable_msi+0x0/0x60) from [<7f0057d4>] (sxdma_irq_free+0x44/0x48 [sxdma])
[bhelgaas: add crash info]
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjørn Erik Nilsen <ben@datarespons.no>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
When using devm_ioremap_resource(), we do not need to check the return
value of platform_get_resource(), so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marek Vasut <marex@denx.de>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tegra20 and Tegra30 do not support gen2 PCIe, so correct the
register setting to disable it.
Signed-off-by: Eric Brower <ebrower@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c23 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: stable@vger.kernel.org # v3.5+
Replace the .find_device function pointer in struct acpi_bus_type
with a new one, .find_companion, that is supposed to point to a
function returning struct acpi_device pointer (instead of an int)
and takes one argument (instead of two). This way the role of
this callback is more clear and the implementation of it can
be more straightforward.
Update all of the users of struct acpi_bus_type (PCI, PNP/ACPI and
USB) to reflect the structure change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com> # for USB/ACPI
It is much more efficient to use acpi_find_child_device()
for child devices lookup in acpi_pci_find_device() and pass
ACPI_COMPANION(dev->parent) to it directly instead of obtaining
ACPI_HANDLE() of ACPI_COMPANION(dev->parent) and passing it to
acpi_find_child() which has to run acpi_bus_get_device() to
obtain ACPI_COMPANION(dev->parent) from that again.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acpiphp_enumerate_slots() walks ACPI namenamespace under
a PCI host bridge with callback register_slot().
register_slot() evaluates _ADR for all the device objects
and emits a warning message for any error. Some platforms
have _HID device objects (such as HPET and IPMI), which
trigger unnecessary warning messages.
This patch avoids emitting a warning message when a target
device object does not have _ADR.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This tool hasn't been maintained in over a decade, and is pretty much
useless these days. Let's pretend it never happened.
Also remove a long-dead email address.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make pcie-io-aperture and the IO port MBUS ID in ranges optional. If not
provided the bridge reports to Linux that IO space mapping is not supported
and refuses to configure an IO MBUS window.
This allows both complete disable (do not specify pcie-io-aperture) and
per-port disable (do not specify a IO target ranges entry for the port).
Most PCIe devices these days do not require IO support to function, so
having an option to disable it in the driver is useful.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
When PCI_COMMAND_MEMORY/PCI_COMMAND_IO are cleared, the bridge should not
allocate windows or even look at the window limit/base registers.
Otherwise we may set up bogus windows while the PCI core code performs
discovery. The core will leave PCI_COMMAND_IO cleared if it doesn't need
an IO window.
Have mvebu_pcie_handle_*_change respect the bits, and call the change
function whenever the bits changes.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The emulated bridge does not support interrupts, so it should return the
value 0 for Interrupt Line and Interrupt Pin. This indicates that
interrupts are not supported.
Since Max_Lat and Min_Gnt are also in the same 32-bit word, we return
0 for them, which means "do not care."
This corrects an error message from the kernel:
pci 0000:00:01.0: of_irq_parse_pci() failed with rc=135
Which is due to the default return of 0xFFFFFFFF indicating that
interrupts are supported.
The error message regression was caused by 16b84e5a50 ("of/irq: Create
of_irq_parse_and_map_pci() to consolidate arch code.")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
There are no writable bits in the secondary status register, only RO and
RW1C (write-1-to-clear) bits. The driver never sets any of the RW1C bits,
so the status register should always be 0, just remove the set from the
write path.
Someday the RW1C bits should be copied/cleared directly from registers in
the HW.
[bhelgaas: changelog tweaks]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
I'm seeing traces analogous to the one below in Thunderbolt testing:
WARNING: CPU: 3 PID: 76 at /scratch/rafael/work/linux-pm/fs/sysfs/group.c:214 sysfs_remove_group+0x59/0xe0()
sysfs group ffffffff81c6c500 not found for kobject '0000:08'
Modules linked in: ...
CPU: 3 PID: 76 Comm: kworker/u16:7 Not tainted 3.13.0-rc1+ #76
Hardware name: Acer Aspire S5-391/Venus , BIOS V1.02 05/29/2012
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801644b9ac8 ffffffff816b23bf 0000000000000007
ffff8801644b9b18 ffff8801644b9b08 ffffffff81046607 ffff88016925b800
0000000000000000 ffffffff81c6c500 ffff88016924f928 ffff88016924f800
Call Trace:
[<ffffffff816b23bf>] dump_stack+0x4e/0x71
[<ffffffff81046607>] warn_slowpath_common+0x87/0xb0
[<ffffffff810466d1>] warn_slowpath_fmt+0x41/0x50
[<ffffffff811e42ef>] ? sysfs_get_dirent_ns+0x6f/0x80
[<ffffffff811e5389>] sysfs_remove_group+0x59/0xe0
[<ffffffff8149f00b>] dpm_sysfs_remove+0x3b/0x50
[<ffffffff81495818>] device_del+0x58/0x1c0
[<ffffffff814959c8>] device_unregister+0x48/0x60
[<ffffffff813254fe>] pci_remove_bus+0x6e/0x80
[<ffffffff81325548>] pci_remove_bus_device+0x38/0x110
[<ffffffff8132555d>] pci_remove_bus_device+0x4d/0x110
[<ffffffff81325639>] pci_stop_and_remove_bus_device+0x19/0x20
[<ffffffff813418d0>] disable_slot+0x20/0xe0
[<ffffffff81341a38>] acpiphp_check_bridge+0xa8/0xd0
[<ffffffff813427ad>] hotplug_event+0x17d/0x220
[<ffffffff81342880>] hotplug_event_work+0x30/0x70
[<ffffffff8136d665>] acpi_hotplug_work_fn+0x18/0x24
[<ffffffff81061331>] process_one_work+0x261/0x450
[<ffffffff81061a7e>] worker_thread+0x21e/0x370
[<ffffffff81061860>] ? rescuer_thread+0x300/0x300
[<ffffffff81068342>] kthread+0xd2/0xe0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
[<ffffffff816c19bc>] ret_from_fork+0x7c/0xb0
[<ffffffff81068270>] ? flush_kthread_worker+0x70/0x70
(Mika Westerberg sees them too in his tests).
Some investigation documented in kernel bug #65281 led me to the
conclusion that the source of the problem is the device_del() in
pci_stop_dev() as it now causes the sysfs directory of the device to be
removed recursively along with all of its subdirectories. That includes
the sysfs directory of the device's subordinate bus (dev->subordinate) and
its "power" group.
Consequently, when pci_remove_bus() is called for dev->subordinate in
pci_remove_bus_device(), it calls device_unregister(&bus->dev), but at this
point the sysfs directory of bus->dev doesn't exist any more and its
"power" group doesn't exist either. Thus, when dpm_sysfs_remove() called
from device_del() tries to remove that group, it triggers the above
warning.
That indicates a logical mistake in the design of
pci_stop_and_remove_bus_device(), which causes bus device objects to be
left behind their parents (bridge device objects) and can be fixed by
moving the device_del() from pci_stop_dev() into pci_destroy_dev(), so
pci_remove_bus() can be called for the device's subordinate bus before the
device itself is unregistered from the hierarchy. Still, the driver, if
any, should be detached from the device in pci_stop_dev(), so use
device_release_driver() directly from there.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281#c6
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If we are already on a CPU local to the device, call the driver .probe()
method directly without using work_on_cpu().
This is a workaround for a lockdep warning in the following scenario:
pci_call_probe
work_on_cpu(cpu, local_pci_probe, ...)
driver .probe
pci_enable_sriov
...
pci_bus_add_device
...
pci_call_probe
work_on_cpu(cpu, local_pci_probe, ...)
It would be better to fix PCI so we don't call VF driver .probe() methods
from inside a PF driver .probe() method, but that's a bigger project.
[bhelgaas: open bugzilla, rework comments & changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=65071
Link: http://lkml.kernel.org/r/CAE9FiQXYQEAZ=0sG6+2OdffBqfLS9MpoN1xviRR9aDbxPxcKxQ@mail.gmail.com
Link: http://lkml.kernel.org/r/20130624195942.40795.27292.stgit@ahduyck-cp1.jf.intel.com
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
When SR-IOV is disabled (VF Enable is cleared), NumVFs is not very useful,
so this patch clears it out to prevent confusing lspci output like that
below. We already clear NumVFs in sriov_disable(), and this does the same
when we disable SR-IOV as part of parsing the SR-IOV capability.
$ lspci -vvv -s 13:00.0
13:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01)
Capabilities: [160 v1] Single Root I/O Virtualization (SR-IOV)
IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy+
Initial VFs: 64, Total VFs: 64, Number of VFs: 64, ...
[bhelgaas: changelog]
Signed-off-by: ethan.zhao <ethan.kernel@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Modify the ACPI namespace scanning code to register a struct
acpi_device object for every namespace node representing a device,
processor and so on, even if the device represented by that namespace
node is reported to be not present and not functional by _STA.
There are multiple reasons to do that. First of all, it avoids
quite a lot of overhead when struct acpi_device objects are
deleted every time acpi_bus_trim() is run and then added again
by a subsequent acpi_bus_scan() for the same scope, although the
namespace objects they correspond to stay in memory all the time
(which always is the case on a vast majority of systems).
Second, it will allow user space to see that there are namespace
nodes representing devices that are not present at the moment and may
be added to the system. It will also allow user space to evaluate
_SUN for those nodes to check what physical slots the "missing"
devices may be put into and it will make sense to add a sysfs
attribute for _STA evaluation after this change (that will be
useful for thermal management on some systems).
Next, it will help to consolidate the ACPI hotplug handling among
subsystems by making it possible to store hotplug-related information
in struct acpi_device objects in a standard common way.
Finally, it will help to avoid a race condition related to the
deletion of ACPI namespace nodes. Namely, namespace nodes may be
deleted as a result of a table unload triggered by _EJ0 or _DCK.
If a hotplug notification for one of those nodes is triggered
right before the deletion and it executes a hotplug callback
via acpi_hotplug_execute(), the ACPI handle passed to that
callback may be stale when the callback actually runs. One way
to work around that is to always pass struct acpi_device pointers
to hotplug callbacks after doing a get_device() on the objects in
question which eliminates the use-after-free possibility (the ACPI
handles in those objects are invalidated by acpi_scan_drop_device(),
so they will trigger ACPICA errors on attempts to use them).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.32+
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Commit bd950799d9 (PCI: acpiphp: Convert to dynamic debug) removed users
of acpiphp_debug variable and the variable itself but the declaration was
left in the header file. Drop this unused declaration.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jingoo Han