This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case where need_resched() is set in between the cpu_idle() and
pm_idle() calls we were missing an else case for just re-enabling local
IRQs and bailing out. This was noticed by the irqs_disabled() warning,
even though IRQs were being re-enabled elsewhere.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and moves check_pgt_cache() up under the
!need_resched() tight loop, rather than simply calling in to it when
exiting idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The open function got the BKL via the big push down. Replace it by
preempt_enable/disable as this is sufficient for an UP machine.
The ioctl can be unlocked because there is no functionality which
requires serialization. The usage by multiple callers is broken with
and without the BKL due to the local static variable addr.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to handle the cache disabled case. Fixes breakage introduced by
37443ef3f0 ("sh: Migrate SH-4 cacheflush
ops to function pointers."). Without this patch configuring caches off
with CONFIG_CACHE_OFF=y makes kfr2r09 and migo-r lock up in fbdev
deferred io or early user space.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently The SH-4 cache flushing code uses flush_cache_4096() for most
of the real flushing work, which breaks down to a fixed 4096 unroll and
increment. Not only is this sub-optimal for larger page sizes, it's also
uncovered a bug in sh4_flush_dcache_page() when large page sizes are used
and we have no cache aliases -- resulting in only a part of the page's
D-cache lines being written back.
Signed-off-by: Valentin Sitdikov <valentin.sitdikov@siemens.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Fix MODPOST warning
powerpc/oprofile: Add ppc750 CL as supported by oprofile
powerpc: warning: allocated section `.data_nosave' not in segment
powerpc/kgdb: Fix build failure caused by "kgdb.c: unused variable 'acc'"
powerpc: Fix hypervisor TLB batching
powerpc/mm: Fix hang accessing top of vmalloc space
powerpc: Fix memory leak in axon_msi.c
powerpc/pmac: Fix issues with sleep on some powerbooks
powerpc64/ftrace: use PACA to retrieve TOC in mod_return_to_handler
powerpc/ftrace: show real return addresses in modules
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2xxx clock: set up clockdomain pointer in struct clk
OMAP: Fix race condition with autodeps
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
omap: Initialization of SDRC params on Zoom2
omap: RX-51: Drop I2C-1 speed to 2200
omap: SDMA: Fixing bug in omap_dma_set_global_params()
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
This reverts commit e9a63a4e55.
This breaks older binutils, where sink-less asserts are broken.
See this commit for further details:
d2ba8b2: x86: Fix assert syntax in vmlinux.lds.S
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
clock24xx.c is missing a omap2_init_clk_clkdm() in its
omap2_clk_init() function. Among other bad effects, this causes the
OMAP hwmod layer to oops on boot.
Thanks to Carlos Aguiar <carlos.aguiar@indt.org.br> and Stefano
Panella <Stefano.Panella@csr.com> for reporting this bug. Thanks to Tony
Lindgren <tony@atomide.com> for N800 booting advice.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Carlos Aguiar <carlos.aguiar@indt.org.br>
Cc: Stefano Panella <Stefano.Panella@csr.com>
Cc: Tony Lindgren <tony@atomide.com>
There is a possible race condition in clockdomain
code handling hw supported idle transitions.
When multiple autodeps dependencies are being added
or removed, a transition of still remaining dependent
powerdomain can result in false readings of the
state counter. This is especially fatal for off mode
state counter, as it could result in a driver not
noticing a context loss.
Fixed by disabling hw supported state transitions
when autodeps are being changed.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
watchdog: Fix rio watchdog probe function
sparc64: Set IRQF_DISABLED on LDC channel IRQs.
sparc64: Fix D-cache flushing on swapin from SW devices.
sparc64: Fix niagara2 perf IRQ bits.
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix a TRACE_IRQS_OFF typo.
sh: Optimize the setup_rt_frame() I-cache flush.
sh: Populate initial secondary CPU info from boot_cpu_data.
sh: Tidy up SMP cpuinfo.
sh: Use boot_cpu_data for FPU tests in sigcontext paths.
sh: ftrace: Fix up syscall tracepoint support.
sh: force dcache flush if dcache_dirty bit set.
sh: update die() output.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/paravirt: Use normal calling sequences for irq enable/disable
x86: fix kernel panic on 32 bits when profiling
x86: Fix Suspend to RAM freeze on Acer Aspire 1511Lmi laptop
x86, vmi: Mark VMI deprecated and schedule it for removal
The linker scripts grew some use of weirdly wrong linker script syntax.
It happens to work, but it's not what the syntax is documented to be.
Clean it up to use the official syntax.
Signed-off-by: Roland McGrath <roland@redhat.com>
CC: Ian Lance Taylor <iant@google.com>
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch initializes the correct SDRC settings required
for DVFS on Zoom2.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Argument tparams was not being used to program
global register GCR.HI_THREAD_RESERVED. This patch fixes the same.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In 'cdd6c482c9ff9c55475ee7392ec8f672eddb7be6', we renamed
Performance Counters -> Performance Events.
The name showed up in /proc/interrupts also needs a change. I use
PMI (Performance monitoring interrupt) here, since it is the
official name used in Intel's documents.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091014105039.GA22670@uhli>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes the hwcap bit for the high gprs feature to be visible
in /proc/cpuinfo.
Signed-off-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hypfs never worked on systems that only provide D204 subcode 6.
In these cases we nevertheless used subcode 7. With this fix, we
use subcode 6, if it is available and the system does not provide
subcode 7.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This plugs in support for NMI counting per-CPU via irq_cpustat_t.
Modelled after the x86 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define our own
set_restore_sigmask() function. This saves the costly SMP-safe set_bit
operation, which we do not need for the sigmask flag since TIF_SIGPENDING
always has to be set too.
Based on the x86 and powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The resume_userspace path had TRACE_IRQS_OFF written incorrectly and so
never handled the transition properly. This was fixed once before but
seems to have made it back in the tree. Fix it for good.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This only needs to flush the return code via the legacy path, and just
invalidates uselessly otherwise. This makes the behaviour consistent for
all of the trampoline setup paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The secondary CPU info was seeing corrupted results due to not entering
all of the setup paths taken by the boot CPU. So we just memcpy() the
boot cpu data over directly, and then fix up the per-CPU bits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We do not want to use smp_processor_id() from these paths, as they trip
preempt BUGs. Switch the test over to the boot cpu directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
making a powerpc target with PCI support, shows the
following warning:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x10430): Section mismatch in reference from the
function pcibios_allocate_bus_resources() to the function .init.text:reparent_resources()
The function pcibios_allocate_bus_resources() references
the function __init reparent_resources().
This is often because pcibios_allocate_bus_resources lacks a __init
annotation or the annotation of reparent_resources is wrong.
This patch fix this warning by removing the __init
annotation before reparent_resources.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Here's a patch that adds the ppc750 CL cpu as supported by oprofile.
Signed-off-by: Dragos Tatulea <dtatulea@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to align before the output section. Having the align inside
the output section causes the linker to put some filler in there,
which makes it a non-empty section, but this section isn't assigned to
a segment so you get a warning from the linker.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
'acc' isn't used anywhere and thus triggers gcc warning, which causes
build error with CONFIG_PPC_DISABLE_WERROR=n (default):
cc1: warnings being treated as errors
arch/powerpc/kernel/kgdb.c: In function 'gdb_regs_to_pt_regs':
arch/powerpc/kernel/kgdb.c:289: warning: unused variable 'acc'
make[1]: *** [arch/powerpc/kernel/kgdb.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Profiling of a page fault scalability microbenchmark shows flush_hash_range
is not calling the batch hpte invalidate hcall (H_BULK_REMOVE).
It turns out we have a duplicate firmware feature for hcall-bulk and the
current setup code stops after finding the first match. This meant we never
batch and always do individual invalidates.
The patch below removes the duplicate and shifts FW_FEATURE_CMO to close
the gap. With the patch applied the single threaded page fault rate improves
from 217169 to 238755 per second on a POWER5 test box, a 10% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pSeries, we always force the IO space to be mapped using 4K
pages even with a 64K base page size to cope with some limitations
in the HV interface to some devices.
However, the SLB miss handler code to discriminate between vmalloc
and ioremap space uses a CPU feature section such that the code
is nop'ed out when the processor support large pages non-cachable
mappings.
Thus, we end up always using the ioremap page size for vmalloc
segments on such processors, causing a discrepency between the
segment and the hash table, and thus a hang continously hashing
the page.
It works for the first segment of the vmalloc space since that
segment is "bolted" in by C code correctly, and thankfully we
almost never use the vmalloc space beyond the first segment,
but the new percpu code made the bug happen.
This fixes it by removing the feature section from the assembly,
we now always do the comparison between vmalloc and ioremap.
Signed-off-by; Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mundt