Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.
Also clean up locking and clear possibly stale ht cap.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!
This has been tested with ath9k.
The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax
RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The QUECVT flag should not prevent conversions from
being granted immediately when the convert queue is
empty.
Signed-off-by: David Teigland <teigland@redhat.com>
net/ipv4/tcp_ipv4.c: In function 'tcp_v4_init_sock':
net/ipv4/tcp_ipv4.c:1891:19: warning: unused variable 'tp' [-Wunused-variable]
net/ipv6/tcp_ipv6.c: In function 'tcp_v6_init_sock':
net/ipv6/tcp_ipv6.c:1836:19: warning: unused variable 'tp' [-Wunused-variable]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"Here's my usual Sunday push, just for one revert which PeterZ hollered
about after last weeks push. Other than that, all seems strangely
quiet as far as fixes go in non-platform ARM land at the moment."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for powerpc. Note the addition to the generic
irq.h. This is part of a 3-patches regression fix for mpic due to
changes in how IRQ_TYPE_NONE is being handled. Thomas agreed to the
addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
replied with an Ack to the actual patch yet. I don't to wait much
longer with these patches tho."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mpic: Properly set default triggers
irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
powerpc/mpic: Fix confusion between hw_irq and virq
powerpc/pmac: Don't add_timer() twice
powerpc/eeh: Fix crash caused by null eeh_dev
powerpc/mpc85xx: add MPIC message dts node
powerpc/mpic_msgr: fix offset error when setting mer register
powerpc/mpic_msgr: add lock for MPIC message global variable
powerpc/mpic_msgr: fix compile error when SMP disabled
powerpc: fix build when CONFIG_BOOKE_WDT is enabled
powerpc/85xx: don't call of_platform_bus_probe() twice
Pull networking fixes from David Miller:
1) Fix namespace init and cleanup in phonet to fix some oopses, from
Eric W. Biederman.
2) Missing kfree_skb() in AF_KEY, from Julia Lawall.
3) Refcount leak and source address handling fix in l2tp from James
Chapman.
4) Memory leak fix in CAIF from Tomasz Gregorek.
5) When routes are cloned from ipv6 addrconf routes, we don't process
expirations properly. Fix from Gao Feng.
6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.
7) Only enable interrupts in 8139cp driver after we've registered the
IRQ handler. From Jason Wang.
8) Fix too many reads of KS_CIDER register in ks8851 during probe,
fixing crashes on spurious interrupts. From Matt Renzelmann.
9) Missing include in ath5k driver and missing iounmap on probe
failure, from Jonathan Bither.
10) Fix RX packet handling in smsc911x driver, from Will Deacon.
11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.
12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
buffers are easily overflown. Fix from Davide Cimingahi.
13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.
14) gred packet scheduler can dump in WRED more when doing a netlink
dump. Fix from David Ward.
15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.
16) Dummy device needs ->ndo_uninit handler to properly handle
->ndo_init failures. From Hiroaki SHIMODA.
17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.
18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.
19) Missing iounmap in farsync WAN driver, from Julia Lawall.
20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
the receive window properly, and this hurts performance. Fix from
Eric Dumazet.
21) Network namespace init failure can leak net_generic data, fix from
Julian Anastasov.
22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
SKBs. From Eric Dumazet.
23) New IDs for qmi_wwan driver, from Bjørn Mork.
24) Fix races in ax25_exit(), from Eric W. Biederman.
25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
logic from the IPV4 side. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: fix TCP_MAXSEG for established IPv6 passive sockets
drivers/net: Do not free an IRQ if its request failed
drop_monitor: allow more events per second
ks8851: Fix request_irq/free_irq mismatch
net/hyperv: Adding cancellation to ensure rndis filter is closed
ks8851: Fix mutex deadlock in ks8851_net_stop()
net ax25: Reorder ax25_exit to remove races.
icplus: fix interrupt for IC+ 101A/G and 1001LF
net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
ksz884x: don't copy too much in netdev_set_mac_address()
tcp: fix retransmit of partially acked frames
netns: do not leak net_generic data on failed init
net/sock.h: fix sk_peek_off kernel-doc warning
tcp: fix tcp_grow_window() for large incoming frames
drivers/net/wan/farsync.c: add missing iounmap
davinci_mdio: Fix MDIO timeout check
ipv6: clean up rt6_clean_expires
ipv6: fix rt6_update_expires
arcnet: rimi: Fix device name in debug output
...
This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.
This in turn makes us read the HW state and update the irq desc
accordingly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).
The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.
However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.
Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.
The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.
The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.
CC: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factorize code, since most fetched values are int type.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit moves the (substantial) common code shared between
tcp_v4_init_sock() and tcp_v6_init_sock() to a new address-family
independent function, tcp_init_sock().
Centralizing this functionality should help avoid drift issues,
e.g. where the IPv4 side is updated without a corresponding update to
IPv6. There was already some drift: IPv4 initialized snd_cwnd to
TCP_INIT_CWND, while the IPv6 side was still initializing snd_cwnd to
2 (in this case it should not matter, since snd_cwnd is also
initialized in tcp_init_metrics(), but the general risks and
maintenance overhead remain).
When diffing the old and new code, note that new tcp_init_sock()
function uses the order of steps from the tcp_v4_init_sock()
implementation (the order is slightly different in
tcp_v6_init_sock()).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
splice() from socket to pipe needs linear_to_page() helper to transfert
skb header to part of page.
We can reset the offset in the current sk->sk_sndmsg_page if we are the
last user of the page.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems there is a logic error in trace_drop_common(), since we store
only 64 drops, even if they are from same location.
This fix is a one liner, but we probably need more work to avoid useless
atomic dec/inc
Now I can watch 1 Mpps drops through dropwatch...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes content of hashlist (used to get port struct by
computed index (0...en_port_count-1)). Now the hash list contains only
enabled ports so userspace will be able to say what ports can be used
for tx/rx. This becomes handy when userspace will need to disable ports
which does not belong to active aggregator. By default, newly added port
is enabled.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iov of more than 8 entries are allocated in sendmsg()/recvmsg() through
sock_kmalloc()
As these allocations are temporary only and small enough, it makes sense
to use plain kmalloc() and avoid sk_omem_alloc atomic overhead.
Slightly changed fast path to be even faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mike Waychison <mikew@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are options, which are set up on a socket while performing
TCP handshake. Need to resurrect them on a socket while repairing.
A new sockoption accepts a buffer and parses it. The buffer should
be CODE:VALUE sequence of bytes, where CODE is standard option
code and VALUE is the respective value.
Only 4 options should be handled on repaired socket.
To read 3 out of 4 of these options the TCP_INFO sockoption can be
used. An ability to get the last one (the mss_clamp) was added by
the previous patch.
Now the restore. Three of these options -- timestamp_ok, mss_clamp
and snd_wscale -- are just restored on a coket.
The sack_ok flags has 2 issues. First, whether or not to do sacks
at all. This flag is just read and set back. No other sack info is
saved or restored, since according to the standart and the code
dropping all sack-ed segments is OK, the sender will resubmit them
again, so after the repair we will probably experience a pause in
connection. Next, the fack bit. It's just set back on a socket if
the respective sysctl is set. No collected stats about packets flow
is preserved. As far as I see (plz, correct me if I'm wrong) the
fack-based congestion algorithm survives dropping all of the stats
and repairs itself eventually, probably losing the performance for
that period.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mss_clamp is the only connection-time negotiated option which
cannot be obtained from the user space. Make the TCP_MAXSEG sockopt
report one in the repair mode.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading queues under repair mode is done with recvmsg call.
The queue-under-repair set by TCP_REPAIR_QUEUE option is used
to determine which queue should be read. Thus both send and
receive queue can be read with this.
Caller must pass the MSG_PEEK flag.
Writing to queues is done with sendmsg call and yet again --
the repair-queue option can be used to push data into the
receive queue.
When putting an skb into receive queue a zero tcp header is
appented to its head to address the tcp_hdr(skb)->syn and
the ->fin checks by the (after repair) tcp_recvmsg. These
flags flags are both set to zero and that's why.
The fin cannot be met in the queue while reading the source
socket, since the repair only works for closed/established
sockets and queueing fin packet always changes its state.
The syn in the queue denotes that the respective skb's seq
is "off-by-one" as compared to the actual payload lenght. Thus,
at the rcv queue refill we can just drop this flag and set the
skb's sequences to precice values.
When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent,
waiting for ACKs' (write_seq = snd_nxt <= snd_una). From the
protocol POV the send queue looks like it was sent, but the data
between the write_seq and snd_nxt is lost in the network.
This helps to avoid another sockoption for setting the snd_nxt
sequence. Leaving the whole queue in a 'not yet sent' state (as
it will be after sendmsg-s) will not allow to receive any acks
from the peer since the ack_seq will be after the snd_nxt. Thus
even the ack for the window probe will be dropped and the
connection will be 'locked' with the zero peer window.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes (according the the previous description):
* TCP_REPAIR sockoption
This one just puts the socket in/out of the repair mode.
Allowed for CAP_NET_ADMIN and for closed/establised sockets only.
When repair mode is turned off and the socket happens to be in
the established state the window probe is sent to the peer to
'unlock' the connection.
* TCP_REPAIR_QUEUE sockoption
This one sets the queue which we're about to repair. The
'no-queue' is set by default.
* TCP_QUEUE_SEQ socoption
Sets the write_seq/rcv_nxt of a selected repaired queue.
Allowed for TCP_CLOSE-d sockets only. When the socket changes
its state the other seq-s are changed by the kernel according
to the protocol rules (most of the existing code is actually
reused).
* Ability to forcibly bind a socket to a port
The sk->sk_reuse is set to SK_FORCE_REUSE.
* Immediate connect modification
The connect syscall initializes the connection, then directly jumps
to the code which finalizes it.
* Silent close modification
The close just aborts the connection (similar to SO_LINGER with 0
time) but without sending any FIN/RST-s to peer.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just the preparation patch, which makes the needed for
TCP repair code ready for use.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major fixes here are:
* Build fix for omap_hsmmc with OF against 3.4-rc1.
* Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3,
which broke hotplug card detection when UNSAFE_RESUME is set.
* Fix a race condition in omap_hsmmc with runtime PM.
* Fix two libertas SDIO-powered-resume regressions.
Also small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zl8K
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gHlK
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Signed-off-by: Wenqi Ma <wenqi_ma@trendmicro.com.cn>
Reviewed-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&ks->lock){+.+...}:
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c083dbec>] mutex_lock_nested+0x68/0x3dc
[<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
[<c019c580>] process_one_work+0x2d8/0x518
[<c019cb98>] worker_thread+0x220/0x3a0
[<c01a2ad4>] kthread+0x88/0x94
[<c0107008>] kernel_thread_exit+0x0/0x8
-> #0 ((&ks->irq_work)){+.+...}:
[<c01b7984>] validate_chain+0x914/0x1018
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c019e104>] flush_work+0x4c/0xac
[<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
[<c06b209c>] __dev_close_many+0x98/0xcc
[<c06b2174>] dev_close_many+0x68/0xd0
[<c06b22ec>] rollback_registered_many+0xcc/0x2b8
[<c06b2554>] rollback_registered+0x28/0x34
[<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
[<c06b25f4>] unregister_netdev+0x18/0x20
[<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
[<c049ddf0>] spi_drv_remove+0x18/0x1c
[<c0468e98>] __device_release_driver+0x7c/0xbc
[<c0468f64>] driver_detach+0x8c/0xb4
[<c0467f00>] bus_remove_driver+0xb8/0xe8
[<c01c1d20>] sys_delete_module+0x1e8/0x27c
[<c0105ec0>] ret_fast_syscall+0x0/0x3c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ks->lock);
lock((&ks->irq_work));
lock(&ks->lock);
lock((&ks->irq_work));
*** DEADLOCK ***
4 locks held by rmmod/125:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
#2: (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
#3: (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two options are separate, and some platforms (e.g. arm pxa)
have ISA slots but no ISA dma controller, so they cannot build
drivers using the DMA API functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures like ARM cannot handle large numbers as
arguments to udelay, so the drivers should use mdelay when
delaying for multiple miliseconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No driver should spin the CPU for 10ms, so better use
an msleep, which is allowed in the ->suspend function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Pedersen