This PCIe controller chip is used on the Raspberry Pi 4 and multiple
adapter cards. There is no publicly available documentation for the
chip, yet both the downstream RPi4 kernel and the controller cards
support/advertise LPM support.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Additional debugging to show xHC USBSTS register when stop endpoint
command watchdog triggers and host is assumed dead.
useful to know the current status before the controller is stopped by
the xhci driver and everything is released and freed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't show the same error message for transaction errors and split
transaction errors. It's very confusing while debugging.
Transaction errors are often due to electrical interference.
Split transaction errors are about xHC not being able to
schedule start and complete split transactions needed to address
low- and full-speed devices behind high-speed hubs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case there are multiple Marvell EHCI blocks in system, we need a
different bus name for each one. Otherwise debugfs gets mildly upset about
a directory name in usb/ehci:
debugfs: Directory 'mv ehci' with parent 'ehci' already present!
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out the undocumented and reserved bits of port status/control
register of the root port need to be set to use the HCI in HSIC mode.
Typically the firmware does this, but that is not always good enough,
because the bits get lost if the HSIC clock is disabled (e.g. when
ehci-mv is build as a module).
This supplements commit 7b104f890a ("USB: EHCI: ehci-mv: add HSIC
support").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading new kernel via kexec, we need to shutdown host controller to
avoid any un-expected memory accessing during new kernel boot.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200306092328.41253-1-ran.wang_1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This controller timeouts during suspend (S3) with
[ 240.521724] xhci_hcd 0000:30:00.3: WARN: xHC save state timeout
[ 240.521729] xhci_hcd 0000:30:00.3: ERROR mismatched command completion event
thus preventing the system from entering S3.
Moreover it remains in an undefined state where some connected devices stop
working until a reboot.
Apply the XHCI_SUSPEND_DELAY quirk to make it suspend properly.
CC: stable@vger.kernel.org
Signed-off-by: Alberto Mattea <alberto@mattea.info>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
CC: stable@vger.kernel.org
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206531
Fixes: 5abdc2e6e1 ("usb: host: xhci: add urb_enqueue/dequeue/giveback tracers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After this was made buildable for something other than PPC32, kbuild
starts warning
drivers/usb/host/fhci-hcd.c:398:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
I don't know this code, but from the construction (initializing size
with 0 and explicitly using "size +=" in the PIPE_BULK case) I assume
that fallthrough is indeed intended.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20200213085401.27862-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_enter_test_mode()
warning: context imbalance in xhci_enter_test_mode - unexpected unlock
The root cause is the missing annotation at xhci_enter_test_mode()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-24-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_set_port_power()
warning: context imbalance in xhci_set_port_power - unexpected unlock
The root cause is the missing annotation at xhci_set_port_power()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-23-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
CC: stable@vger.kernel.org
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206531
Fixes: 5abdc2e6e1 ("usb: host: xhci: add urb_enqueue/dequeue/giveback tracers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20200214115634.30e8ebf2@gandalf.local.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fc57313d10.
Marek reports that it breaks things:
This patch landed in today's linux-next (20200211) and causes
NULL pointer dereference during second suspend/resume cycle on
Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board:
A more complete fix will be added soon.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fc57313d10 ("xhci: Fix memory leak when caching protocol extended capability PSI tables")
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1580114262-25029-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.
usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.
This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b9 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.
This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.
The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.
Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Set the MODULE_FIRMWARE for tegra186, it's registered for 124/210 and
ensures the firmware is available at the appropriate time such as in
the initrd, else if the firmware is unavailable the driver fails with
the following errors:
tegra-xusb 3530000.usb: Direct firmware load for nvidia/tegra186/xusb.bin failed with error -2
tegra-xusb 3530000.usb: failed to request firmware: -2
tegra-xusb 3530000.usb: failed to load firmware: -2
tegra-xusb: probe of 3530000.usb failed with error -2
Fixes: 5f9be5f3f8 ("usb: host: xhci-tegra: Add Tegra186 XUSB support")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200120141910.116097-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are few stale fields in tegra_ehci_hcd structure, let's remove them.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-21-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to use usb_phy_set_suspend during of driver's probe
because now PHY driver enables hardware during of PHY's initialization.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-20-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found that PHY's enable refcounting was broken and after fixing it
I also found that machine started to hang after EHCI driver module
removal. Turned out that the teardown order is incorrect because HCD must
be unregistered *before* PHY's disabling. Note that it is also not correct
to assert the shared reset during of driver's removal because PHY takes
care of resetting shared pads and thus it's better to remove that part
from the EHCI driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-9-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when an error occurs when calling devm_gpiod_get_optional or
calling gpiod_to_irq it causes an uninitialized error return in variable
'error' to be returned. Fix this by ensuring the error variable is set
from da8xx_ohci->oc_gpio and oc_irq.
Thanks to Dan Carpenter for spotting the uninitialized error in the
gpiod_to_irq failure case.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200107123901.101190-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc -O3 warns about correct code:
inlined from 'oxu_hub_control.constprop' at drivers/usb/host/oxu210hp-hcd.c:3652:3:
include/linux/string.h:411:9: error: argument 1 null where non-null expected [-Werror=nonnull]
return __builtin_memset(p, c, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_hub_control.constprop':
include/linux/string.h:411:9: note: in a call to built-in function '__builtin_memset'
Expand the code slightly to let gcc better understand it and
not warn any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107214354.1008937-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The USB_OCTEON_EHCI is deprecated and only selects proper driver so
there is no need to compile test it. Since it selects
USB_EHCI_BIG_ENDIAN_MMIO it causes compilation failures on certain big
endian architectures (e.g. m68k):
In file included from drivers/usb/host/ehci-mxc.c:19:0:
drivers/usb/host/ehci.h: In function ‘ehci_readl’:
drivers/usb/host/ehci.h:743:3: error:
implicit declaration of function ‘readl_be’ [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1577778392-570-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB host drivers can be compile tested to increase build
coverage. Add 'if' conditional to 'default y' so they will not get
enabled by default on all other architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191230172215.17370-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk-xhci platform glue sets the DMA mask to 32 bits on its own,
which was needed before commit fda182d80a ("usb: xhci: configure
32-bit DMA if the controller does not support 64-bit DMA"), but now it
has no effect, because xhci_gen_setup() sets it up for us according to
hardware capabilities. Remove the useless code.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20191219093954.163417-1-tfiga@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some special dance is needed to initialize the HSIC port.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is merely a cleanup. None of these is used anywhere.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-4-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may be using a NOP transceiver and those are treated specially by the
USB core and return -ENODEV with devm_phy_get().
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-3-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dc ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
technical-specifications/ehci-specification-for-usb.pdf]
Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver cannot call pci_set_power_state() on non-pci xhci host
controllers. For example, NVIDIA Tegra XHCI host controller which acts
as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform
hits this issue during shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This implements basic engine-level powergate support which allows the
XUSB controller to be put into a low power mode on system sleep and get
it out of that low power mode again on resume.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-11-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define the offsets of the registers that need to be saved on suspend and
restored on resume for the various NVIDIA Tegra generations supported by
the XUSB driver.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-10-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XUSB controller contains registers that need to be saved on suspend
and restored on resume in addition to the XHCI specific registers. Add
support for saving and restoring the XUSB specific context.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-9-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of things can currently go wrong after the XUSB controller has
been enabled, which means that it might need to be disabled again before
it has ever been used.
Avoid this by delaying runtime PM enablement until it's really required
right before registers are accessed for the first time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-8-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The base address of the XUSB controller's registers is already stored in
the HCD. Move assignment to the HCD fields to an earlier point so that
they can be reused in the tegra_xusb_config() function. This avoids the
need to pass the base address as an extra parameter, which in turn comes
in handy in subsequent patches that need to call this function from the
suspend/resume paths where these values are no longer readily available.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-7-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract a helper that enables message generation from the firmware. This
removes clutter from tegra_xusb_probe() and will also come in useful for
subsequent patches that introduce suspend/resume support.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-6-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Falcon CPU state is a suboptimal indicator for firmware readiness,
since the Falcon can be in a running state if the firmware is handling
port state changes or running other tasks. Instead, the driver should
check the STS_CNR bit to determine whether or not the firmware has been
successfully loaded and is ready for XHCI operation.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-5-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use a fixed duration sleep to wait for the DMA controller to
become ready. Instead, poll the L2IMEMOP_RESULT register for the VLD
flag to determine when the XUSB controller's DMA master is ready.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-4-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subsequent patches for system suspend/resume support will need to reload
the firmware on resume. Since the firmware remains in system memory, the
driver doesn't need to reload it from the filesystem. However, the XUSB
controller will be reset across suspend/resume, so it needs to load the
firmware into its microcontroller on resume.
Split the firmware request and the firmware load code into two separate
functions so that the driver can reuse the firmware in system memory to
reload the microcontroller on resume.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-3-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra_xusb_mbox_regs structure was misspelled tega_xusb_mbox_regs.
Fortunately this was done consistently so it didn't cause any issues.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-2-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_sh_platdata was never used, remove it. It can be resurrected from
git history when needed.
This basically reverts commit 3e0c70d050 ("usb: ehci-sh: Add PHY
init function with platform data").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20191206132849.29406-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132910.29310-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XUSB phy needs to be enabled before un-powergating the power partitions.
However in the current sequence, it happens opposite. Correct the phy
enable and powergating partition sequence to avoid any boot hangs.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jui Chang Kuo <jckuo@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1572859470-7823-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Ice Lake has two xHCI controllers one on PCH and the other as part
of the CPU itself. The latter is also part of the so called Type C
Subsystem (TCSS) sharing ACPI power resources with the PCIe root ports
and the Thunderbolt controllers. In order to put the whole TCSS block
into D3cold the xHCI needs to be runtime suspended as well when idle.
For this reason allow runtime PM as default for Ice Lake TCSS xHCI
controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "USB: HCD: support giveback of URB in tasklet context"[1]
introduced giveback of urb in tasklet context. [1] This patch was
applied to ehci but not xhci. [2] This patch significantly reduces
the hard irq time of xhci. Especially for uvc driver, the hard irq
including the uvc completion function runs quite long but applying
this patch reduces the hard irq time of xhci.
I have tested four SS devices to check if performance degradation
occurs when urb completion functions run in the tasklet context.
As a result of the test, all devices works well and shows very
similar performance with the upstream kernel. Moreover, usb ethernet
adapter show better performance than the upstream kernel about 5% for
RX and 2% for TX. Four SS devices is as follows.
SS devices for test
1. WD My Passport 2TB (external hard drive)
2. Sandisk Ultra Flair USB 3.0 32GB
3. Logitech Brio webcam
4. Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
Test description
1. Mass storage (hard drive) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
2. Mass storage (flash memory) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
3. Webcam streaming performance test
- run simple capture program and get the average frame rate per second
- capture 1500 frames
- program link
https://github.com/asfaca/Webcam-performance-analyzing-tool
- video resolution : 4096 X 2160 (4K) at 30 or 24 fps
- device (Logitech Brio) spec url for the highest resolution and fps
https://support.logitech.com/en_gb/product/brio-stream/specs
4. USB Ethernet adapter performance test
- directly connect two linux machines with ethernet cable
- run pktgen of linux kernel and send 1500 bytes packets
- run vnstat to measure the network bandwidth for 180 seconds
Test machine
- CPU : Intel i5-7600 @ 3.5GHz
Test results
1. Mass storage (hard drive) performance test
WD My Passport 2TB (external hard drive)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
103.667MB/s | 103.692MB/s
--------------------------------------------------------------------
2. Mass storage (flash memory) performance test
Sandisk Ultra Flair USB 3.0 32GB
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
129.727MB/s | 130.2MB/s
--------------------------------------------------------------------
3. Webcam streaming performance test
Logitech Brio webcam
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
26.4451 fps | 26.3949 fps
--------------------------------------------------------------------
4. USB Ethernet adapter performance test
Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
RX 933.86 Mbit/s | 983.86 Mbit/s
--------------------------------------------------------------------
TX 830.18 Mbit/s | 882.75 Mbit/s
--------------------------------------------------------------------
[1], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=94dfd7edfd5c9b605caf7b562de7a813d216e011
[2], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=428aac8a81058e2303677a8fbf26670229e51d3a
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace when a register in the doorbell array is written,
both for host controller command doorbell and device doorbells,
including for which endpoint and stream
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some situations, the software handles TRB events slower
than adding TRBs, then xhci_handle_event can't return zero
long time, the xHC will consider the event ring is full,
and trigger "Event Ring Full" error, but in fact, the software
has already finished lots of events, just no chance to
update ERDP (event ring dequeue pointer).
In this commit, we force update ERDP if half of TRBS_PER_SEGMENT
events have handled to avoid "Event Ring Full" error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver forgets to call clk_put when probe fails and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191102062245.4014-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of places in the driver where it fails
to maintain __iomem on pointers used to access registers
so fixup the warnings by adding these in the appropriate
places.
Examples of the sparse warnings fixed:
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:681:16: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:681:16: expected void const volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:681:16: got void *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191017171934.8771-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcma_hcd_probe misses a check for devm_gpiod_get and may miss
the error.
Add a check for it and return the error if a failure occurs.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191016083531.5734-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hcd pointer in ohci_hcd_nxp_probe() is
being initialised with a 0, so fix to NULL to
avoid the following sparse warning:
drivers/usb/host/ohci-nxp.c:153:31: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Link: https://lore.kernel.org/r/20191015141945.16067-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;
xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62: expected unsigned int [usertype] field0
xhci-debugfs.c:205:62: got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62: expected unsigned int [usertype] field1
xhci-debugfs.c:206:62: got restricted __le32
...
[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arguments to queue_trb are always byteswapped to LE for placement in
the ring, but this should not happen in the case of immediate data; the
bytes copied out of transfer_buffer are already in the correct order.
Add a complementary byteswap so the bytes end up in the ring correctly.
This was observed on BE ppc64 with a "Texas Instruments TUSB73x0
SuperSpeed USB 3.0 xHCI Host Controller [104c:8241]" as a ch341
usb-serial adapter ("1a86:7523 QinHeng Electronics HL-340 USB-Serial
adapter") always transmitting the same character (generally NUL) over
the serial link regardless of the key pressed.
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer") schedules work
to clear TT buffer, but causes a use-after-free regression at the same time
Make sure hub_tt_work finishes before endpoint is disabled, otherwise
the work will dereference already freed endpoint and device related
pointers.
This was triggered when usb core failed to read the configuration
descriptor of a FS/LS device during enumeration.
xhci driver queued clear_tt_work while usb core freed and reallocated
a new device for the next enumeration attempt.
EHCI driver implents ehci_endpoint_disable() that makes sure
clear_tt_work has finished before it returns, but xhci lacks this support.
usb core will call hcd->driver->endpoint_disable() callback before
disabling endpoints, so we want this in xhci as well.
The added xhci_endpoint_disable() is based on ehci_endpoint_disable()
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
This commit adds Tegra194 XUSB host mode controller support. This is
very similar to the existing Tegra124/Tegra210/Tegra186 XHCI, except
1. the number of ports and PHYs differs
2. the IPFS wrapper being removed
3. mailbox registers address changes
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Link: https://lore.kernel.org/r/20191004162906.4818-3-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra194 XUSB host controller has rearranged mailbox registers. This
commit makes mailbox registers address a part of "soc" data so that
xhci-tegra driver can be used for Tegra194.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Link: https://lore.kernel.org/r/20191004162906.4818-2-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udev stored in ep->hcpriv might be NULL if tt buffer is cleared
due to a halted control endpoint during device enumeration
xhci_clear_tt_buffer_complete is called by hub_tt_work() once it's
scheduled, and by then usb core might have freed and allocated a
new udev for the next enumeration attempt.
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-9-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit f7fac17ca9 ("xhci: Convert xhci_handshake() to use
readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend.
Although the algorithms are essentially the same, the old max timeout is
(usec + usec * time of doing readl()), and the new max timeout is just
usec, which is much less than the old one.
Increase the timeout to make ASMedia xHCI able to suspend again.
BugLink: https://bugs.launchpad.net/bugs/1844021
Fixes: f7fac17ca9 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.
[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early xHCI 1.1 spec did not mention USB 3.1 capable hosts should set
sbrn to 0x31, or that the minor revision is a two digit BCD
containing minor and sub-minor numbers.
This was later clarified in xHCI 1.2.
Some USB 3.1 capable hosts therefore have sbrn set to 0x30, or minor
revision set to 0x1 instead of 0x10.
Detect the USB 3.1 capability correctly for these hosts as well
Fixes: ddd57980a0 ("xhci: detect USB 3.2 capable host controllers correctly")
Cc: <stable@vger.kernel.org> # v4.18+
Cc: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.
Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.
Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED
While at it fix the split line error message
Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a clock enable counter run away problem in resume ohci_at91. Code
enables clock that was never disabled in case of non wakeup interface. That
would make clock unstoppable in future.
Use proper alternative to start clocks only if they were stopped before.
Signed-off-by: Boris Krasnovskiy <Boris.Krasnovskiy@lairdconnect.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190911064154.28633-4-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to completely remove marginal power consumption in PM suspend,
we need to let the controller settle down before being stopped.
In ohci_hcd_at91_drv_suspend() function, one additional delay is needed before
to stop the clocks.
Reported-by: Boris Krasnovskiy <Boris.Krasnovskiy@lairdconnect.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190911064154.28633-3-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JC Kuo