i915_gem_vma_create() returns and ERR_PTR() or a valid pointer, it never
returns NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The next step is to modify lpt_enable_clkout_dp to enable support for
"Sequence to enable CLKOUT_DP" and "Sequence to enable CLKOUT_DP
without spread".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because lpt_init_pch_refclk implements the "Sequence to enable
CLKOUT_DP for FDI usage and configure PCH FDI I/O", which is very
similar to "Sequence to enable CLKOUT_DP" and "Sequence to enable
CLKOUT_DP without spread". With the extracted functions we can more
easily implement the two missing sequences.
v2: Rebase (WaMPhyProgramming:hsw comment).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The machines that fall in the "is_sdv" case are some very early
pre-production steppings. This patch may break VGA output after
suspend/resume on these machines.
Even the documentation for the is_sdv cases was removed from BSpec.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The zcrypt device driver has been split into base/bus module, api-module,
card modules and message type modules. The base module has been renamed
from z90crypt to ap.
A module alias (with the well-known z90crypt identifier) will be introduced
that enable users to use their existing way to load the zcrypt device driver.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull networking fixes from David Miller:
"A couple interesting SKB fragment handling fixes, plus the usual small
bits here and there:
1) Fix 64-bit divide build failure on 32-bit platforms in mlx5, from
Tim Gardner.
2) Get rid of a stupid reimplementation on "%*phC" in our sysfs MAC
address printing helper.
3) Fix NETIF_F_SG capability advertisement in hyperv driver, if the
device can't do checksumming offloads then it shouldn't say it can
do SG either. From Haiyang Zhang.
4) bgmac needs to depend on PHYLIB, from Hauke Mehrtens.
5) Don't leak DMA mappings on mapping failures, from Neil Horman.
6) We need to reset the transport header of SKBs in ipv4 before we
attempt to perform early socket demux, just like ipv6 does. From
Eric Dumazet.
7) Add missing locking on vxlan device removal, from Stephen
Hemminger.
8) xen-netfront has to make two passes over an SKB to prepare it for
transfer. One pass calculates the number of slots needed, the
second massages the SKB and fills the slots. Unfortunately, the
first pass doesn't calculate the number of slots properly so we
can end up trying to build a MAX_SKB_FRAGS + 1 SKB which doesn't
work out so well. Fix from Jan Beulich with help and discussion
with several others.
9) Fix a similar problem in tun and macvtap, which have to split up
scatter-gather elements at PAGE_SIZE boundaries. Don't do
zerocopy if it would result in a > MAX_SKB_FRAGS skb. Fixes from
Jason Wang.
10) On receive, once we've decoded the VLAN state completely, clear
skb->vlan_tci. Otherwise demuxed tunnels underneath can trigger
the VLAN code again, corrupting the packet. Fix from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a race in egress prio management
vlan: mask vlan prio bits
macvtap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
tuntap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
pkt_sched: sch_qfq: remove a source of high packet delay/jitter
xen-netfront: pull on receive skb may need to happen earlier
vxlan: add necessary locking on device removal
hyperv: Fix the NETIF_F_SG flag setting in netvsc
net: Fix sysfs_format_mac() code duplication.
be2net: Fix to avoid hardware workaround when not needed
macvtap: do not assume 802.1Q when send vlan packets
macvtap: fix the missing ret value of TUNSETQUEUE
ipv4: set transport header earlier
mlx5 core: Fix __udivdi3 when compiling for 32 bit arches
bgmac: add dependency to phylib
net/irda: fixed style issues in irlan_eth
ethtool: fixed trailing statements in ethtool
ndisc: bool initializations should use true and false
atl1e: unmap partially mapped skb on dma error and free skb
event_id_read() has no reason to kmalloc "struct trace_seq"
(more than PAGE_SIZE!), it can use a small buffer instead.
Note: "if (*ppos) return 0" looks strange and even wrong,
simple_read_from_buffer() handles ppos != 0 case corrrectly.
And it seems that almost every user of trace_seq in this file
should be converted too. Unless you use seq_open(), trace_seq
buys nothing compared to the raw buffer, but it needs a bit
more memory and code.
Link: http://lkml.kernel.org/r/20130718184712.GA4786@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
f_next() looks overcomplicated, and it is not strictly correct
even if this doesn't matter.
Say, FORMAT_FIELD_SEPERATOR should not return NULL (means EOF)
if trace_get_fields() returns an empty list, we should simply
advance to FORMAT_PRINTFMT as we do when we find the end of list.
1. Change f_next() to return "struct list_head *" rather than
"ftrace_event_field *", and change f_show() to do list_entry().
This simplifies the code a bit, only f_show() needs to know
about ftrace_event_field, and f_next() can play with ->prev
directly
2. Change f_next() to not play with ->prev / return inside the
switch() statement. It can simply set node = head/common_head,
the prev-or-advance-to-the-next-magic below does all work.
While at it. f_start() looks overcomplicated too. I don't think
*pos == 0 makes sense as a separate case, just change this code
to do "while" instead of "do/while".
The patch also moves f_start() down, close to f_stop(). This is
purely cosmetic, just to make the locking added by the next patch
more clear/visible.
Link: http://lkml.kernel.org/r/20130718184710.GA4783@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The selftest for function and function graph tracers are defined as
__init, as they are only executed at boot up. The "tracer" structs
that are associated to those tracers are not setup as __init as they
are used after boot. To stop mismatch warnings, those structures
need to be annotated with __ref_data.
Currently, the tracer structures are defined to __read_mostly, as they
do not really change. But in the future they should be converted to
consts, but that will take a little work because they have a "next"
pointer that gets updated when they are registered. That will have to
wait till the next major release.
Link: http://lkml.kernel.org/r/1373596735.17876.84.camel@gandalf.local.home
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some error paths did not handle ref counting properly, and some trace files need
ref counting.
Link: http://lkml.kernel.org/r/1374171524-11948-1-git-send-email-azl@google.com
Cc: stable@vger.kernel.org # 3.10
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: Alexander Z Lam <lambchop468@gmail.com>
Signed-off-by: Alexander Z Lam <azl@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Remove debugfs directories for tracing instances during creation if an error
occurs causing the trace_array for that instance to not be added to
ftrace_trace_arrays. If the directory continues to exist after the error, it
cannot be removed because the respective trace_array is not in
ftrace_trace_arrays.
Link: http://lkml.kernel.org/r/1373502874-1706-2-git-send-email-azl@google.com
Cc: stable@vger.kernel.org # 3.10
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: Alexander Z Lam <lambchop468@gmail.com>
Signed-off-by: Alexander Z Lam <azl@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Wait for disabling all running kprobe handlers when a kprobe
event is disabled, since the caller, trace_remove_event_call()
supposes that a removing event is disabled completely by
disabling the event.
With this change, ftrace can ensure that there is no running
event handlers after disabling it.
Link: http://lkml.kernel.org/r/20130709093526.20138.93100.stgit@mhiramat-M0-7522
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Every perf_trace_buf_prepare() caller does
WARN_ONCE(size > PERF_MAX_TRACE_SIZE, message) and "message" is
almost the same.
Shift this WARN_ONCE() into perf_trace_buf_prepare(). This changes
the meaning of _ONCE, but I think this is fine.
- 4947014 2932448 10104832 17984294 1126b26 vmlinux
+ 4948422 2932448 10104832 17985702 11270a6 vmlinux
on my build.
Link: http://lkml.kernel.org/r/20130617170211.GA19813@redhat.com
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
perf_trace_buf_prepare() + perf_trace_buf_submit(head, task => NULL)
make no sense if hlist_empty(head). Change perf_syscall_enter/exit()
to check sys_data->{enter,exit}_event->perf_events beforehand.
Link: http://lkml.kernel.org/r/20130617170207.GA19806@redhat.com
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
perf_trace_buf_prepare() + perf_trace_buf_submit(head, task => NULL)
make no sense if hlist_empty(head). Change perf_ftrace_function_call()
to check event_function.perf_events beforehand.
Link: http://lkml.kernel.org/r/20130617170204.GA19803@redhat.com
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There have some mismatch between comments with
real function name, update it.
This patch also add some missed function arguments
description.
Link: http://lkml.kernel.org/r/51E3B3B2.4080307@huawei.com
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
For string without format specifiers, use trace_seq_puts()
or trace_seq_putc().
Link: http://lkml.kernel.org/r/51E3B3AC.1000605@huawei.com
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
[ fixed a trace_seq_putc(s, " ") to trace_seq_putc(s, ' ') ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull x86 fixes from Peter Anvin:
"Trying again to get the fixes queue, including the fixed IDT alignment
patch.
The UEFI patch is by far the biggest issue at hand: it is currently
causing quite a few machines to boot. Which is sad, because the only
reason they would is because their BIOSes touch memory that has
already been freed. The other major issue is that we finally have
tracked down the root cause of a significant number of machines
failing to suspend/resume"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure IDT is page aligned
x86, suspend: Handle CPUs which fail to #GP on RDMSR
x86/platform/ce4100: Add header file for reboot type
Revert "UEFI: Don't pass boot services regions to SetVirtualAddressMap()"
efivars: check for EFI_RUNTIME_SERVICES
3.10 wasn't a good release for md. The bio changes left a couple of
bugs, and an md "fix" created another one.
These three patches appear to fix the issues and have been tagged for
-stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=mQEH
-----END PGP SIGNATURE-----
Merge tag 'md-3.11-fixes' of git://neil.brown.name/md
Pull md bug fixes from NeilBrown:
"Sorry boss, back at work now boss. Here's them nice shiny patches ya
wanted. All nicely tagged and justified for -stable and everyfing:
Three bug fixes for md in 3.10
3.10 wasn't a good release for md. The bio changes left a couple of
bugs, and an md "fix" created another one.
These three patches appear to fix the issues and have been tagged for
-stable"
* tag 'md-3.11-fixes' of git://neil.brown.name/md:
md/raid1: fix bio handling problems in process_checks()
md: Remove recent change which allows devices to skip recovery.
md/raid10: fix two problems with RAID10 resync.
To avoid stalls we delay tiling changes and especially hold of
committing the new fence state for as long as possible.
Synchronization points are in the execbuf code and in our gtt fault
handler.
Unfortunately we've missed that tricky detail when adding proper fence
restore code in
commit 19b2dbde57
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jun 12 10:15:12 2013 +0100
drm/i915: Restore fences after resume and GPU resets
The result was that we've restored fences for objects with no tiling,
since the object<->fence link still existed after resume. Now that
wouldn't have been too bad since any subsequent access would have
fixed things up, but if we've changed from tiled to untiled real havoc
happened:
The tiling stride is stored -1 in the fence register, so a stride of 0
resulted in all 1s in the top 32bits, and so a completely bogus fence
spanning everything from the start of the object to the top of the
GTT. The tell-tale in the register dumps looks like:
FENCE START 2: 0x0214d001
FENCE END 2: 0xfffff3ff
Bit 11 isn't set since the hw doesn't store it, even when writing all
1s (at least on my snb here).
To prevent such a gaffle in the future add a sanity check for fences
with an untiled object attached in i915_gem_write_fence.
v2: Fix the WARN, spotted by Chris.
v3: Trying to reuse get_fences looked ugly and obfuscated the code.
Instead reuse update_fence and to make it really dtrt also move the
fence dirty state clearing into update_fence.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60530
Cc: stable@vger.kernel.org (for 3.10 only)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Björn Bidar <theodorstormgrade@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"You'll be terribly disappointed in this, I'm not trying to sneak any
features in or anything, its mostly radeon and intel fixes, a couple
of ARM driver fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/radeon/dpm: add debugfs support for RS780/RS880 (v3)
drm/radeon/dpm/atom: fix broken gcc harder
drm/radeon/dpm/atom: restructure logic to work around a compiler bug
drm/radeon/dpm: fix atom vram table parsing
drm/radeon: fix an endian bug in atom table parsing
drm/radeon: add a module parameter to disable aspm
drm/rcar-du: Use the GEM PRIME helpers
drm/shmobile: Use the GEM PRIME helpers
uvesafb: Really allow mtrr being 0, as documented and warn()ed
radeon kms: do not flush uninitialized hotplug work
drm/radeon/dpm/sumo: handle boost states properly when forcing a perf level
drm/radeon: align VM PTBs (Page Table Blocks) to 32K
drm/radeon: allow selection of alignment in the sub-allocator
drm/radeon: never unpin UVD bo v3
drm/radeon: fix UVD fence emit
drm/radeon: add fault decode function for CIK
drm/radeon: add fault decode function for SI (v2)
drm/radeon: add fault decode function for cayman/TN (v2)
drm/radeon: use radeon device for request firmware
drm/radeon: add missing ttm_eu_backoff_reservation to radeon_bo_list_validate
...
egress_priority_map[] hash table updates are protected by rtnl,
and we never remove elements until device is dismantled.
We have to make sure that before inserting an new element in hash table,
all its fields are committed to memory or else another cpu could
find corrupt values and crash.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 48cc32d38a
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.
But we also have a problem if prio bits are set.
Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.
Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :
16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
0x0000: 0000 0029 8000 c7c3 7103 0001 a0ae e651
0x0010: 0000 0000 ccce 0b00 0000 0000 1011 1213
0x0020: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
0x0030: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233
It seems we are not really ready to properly cope with this right now.
We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.
For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
This bug were introduced from b92946e291
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
The bug were introduced from commit 0690899b4d
(tun: experimental zero copy tx support)
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QFQ+ inherits from QFQ a design choice that may cause a high packet
delay/jitter and a severe short-term unfairness. As QFQ, QFQ+ uses a
special quantity, the system virtual time, to track the service
provided by the ideal system it approximates. When a packet is
dequeued, this quantity must be incremented by the size of the packet,
divided by the sum of the weights of the aggregates waiting to be
served. Tracking this sum correctly is a non-trivial task, because, to
preserve tight service guarantees, the decrement of this sum must be
delayed in a special way [1]: this sum can be decremented only after
that its value would decrease also in the ideal system approximated by
QFQ+. For efficiency, QFQ+ keeps track only of the 'instantaneous'
weight sum, increased and decreased immediately as the weight of an
aggregate changes, and as an aggregate is created or destroyed (which,
in its turn, happens as a consequence of some class being
created/destroyed/changed). However, to avoid the problems caused to
service guarantees by these immediate decreases, QFQ+ increments the
system virtual time using the maximum value allowed for the weight
sum, 2^10, in place of the dynamic, instantaneous value. The
instantaneous value of the weight sum is used only to check whether a
request of weight increase or a class creation can be satisfied.
Unfortunately, the problems caused by this choice are worse than the
temporary degradation of the service guarantees that may occur, when a
class is changed or destroyed, if the instantaneous value of the
weight sum was used to update the system virtual time. In fact, the
fraction of the link bandwidth guaranteed by QFQ+ to each aggregate is
equal to the ratio between the weight of the aggregate and the sum of
the weights of the competing aggregates. The packet delay guaranteed
to the aggregate is instead inversely proportional to the guaranteed
bandwidth. By using the maximum possible value, and not the actual
value of the weight sum, QFQ+ provides each aggregate with the worst
possible service guarantees, and not with service guarantees related
to the actual set of competing aggregates. To see the consequences of
this fact, consider the following simple example.
Suppose that only the following aggregates are backlogged, i.e., that
only the classes in the following aggregates have packets to transmit:
one aggregate with weight 10, say A, and ten aggregates with weight 1,
say B1, B2, ..., B10. In particular, suppose that these aggregates are
always backlogged. Given the weight distribution, the smoothest and
fairest service order would be:
A B1 A B2 A B3 A B4 A B5 A B6 A B7 A B8 A B9 A B10 A B1 A B2 ...
QFQ+ would provide exactly this optimal service if it used the actual
value for the weight sum instead of the maximum possible value, i.e.,
11 instead of 2^10. In contrast, since QFQ+ uses the latter value, it
serves aggregates as follows (easy to prove and to reproduce
experimentally):
A B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A A A A A A A A A A B1 B2 ... B10 A A ...
By replacing 10 with N in the above example, and by increasing N, one
can increase at will the maximum packet delay and the jitter
experienced by the classes in aggregate A.
This patch addresses this issue by just using the above
'instantaneous' value of the weight sum, instead of the maximum
possible value, when updating the system virtual time. After the
instantaneous weight sum is decreased, QFQ+ may deviate from the ideal
service for a time interval in the order of the time to serve one
maximum-size packet for each backlogged class. The worst-case extent
of the deviation exhibited by QFQ+ during this time interval [1] is
basically the same as of the deviation described above (but, without
this patch, QFQ+ suffers from such a deviation all the time). Finally,
this patch modifies the comment to the function qfq_slot_insert, to
make it coherent with the fact that the weight sum used by QFQ+ can
now be lower than the maximum possible value.
[1] P. Valente, "Extending WF2Q+ to support a dynamic traffic mix",
Proceedings of AAA-IDEA'05, June 2005.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups, to
solve that race condition, which was impossible to do before this, so
that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the different
subtrees, instead of having to live in my driver-core tree, causing
merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from others
didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting to
you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here as
well. All of these have been in linux-next this week, with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iEYEABECAAYFAlHoRUUACgkQMUfUDdst+ymkNACdHAjEXZZmXohDuCb2SqyMeQsz
AZcAn3qqJa/NoPEgTCgOkDlAQZM6BnC5
=+Gqk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups,
to solve that race condition, which was impossible to do before this,
so that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the
different subtrees, instead of having to live in my driver-core tree,
causing merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from
others didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting
to you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here
as well. All of these have been in linux-next this week, with no
reported problems"
* tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: fix new kernel-doc warning in base/platform.c
sysfs: use file mode defines from stat.h
sysfs: add more helper macro's for (bin_)attribute(_groups)
driver core: add default groups to struct class
driver core: Introduce device_create_groups
sysfs: prevent warning when only using binary attributes
sysfs: add support for binary attributes in groups
driver core: device.h: add RW and RO attribute macros
sysfs.h: add BIN_ATTR macro
sysfs.h: add ATTRIBUTE_GROUPS() macro
sysfs.h: add __ATTR_RW() macro
* acpi-fixes:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
The BIOS of FUjitsu E753 reports an incorrect initial backlight value
for WIN8 compatible OS, causing backlight to be dark during startup.
This change causes the incorrect initial value from BIOS to be ignored.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60161
Reported-and-tested-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
Except for a slightly big OMAP changes, all rest are small, mostly
boring changes; all either 3.11 regression fixes or stable materials.
- ASoC OMAP fixes due to non-DT OMAP4 removals
- Other ASoC driver changes (sglt5000, wm8978, wm8948, samsung)
- Fix missing locking for snd_pcm_stop() calls in many drivers
- Fix the blocking request_module() in OSS sequencer
- Fix old OSS vwsnd driver builds
- Add a new HD-audio HDMI codec ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=xUZh
-----END PGP SIGNATURE-----
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Except for a slightly big OMAP changes, all rest are small, mostly
boring changes; all either 3.11 regression fixes or stable materials.
- ASoC OMAP fixes due to non-DT OMAP4 removals
- Other ASoC driver changes (sglt5000, wm8978, wm8948, samsung)
- Fix missing locking for snd_pcm_stop() calls in many drivers
- Fix the blocking request_module() in OSS sequencer
- Fix old OSS vwsnd driver builds
- Add a new HD-audio HDMI codec ID"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: seq-oss: Initialize MIDI clients asynchronously
ALSA: hda - Add new GPU codec ID to snd-hda
staging: line6: Fix unlocked snd_pcm_stop() call
[media] saa7134: Fix unlocked snd_pcm_stop() call
ASoC: s6000: Fix unlocked snd_pcm_stop() call
ASoC: atmel: Fix unlocked snd_pcm_stop() call
ALSA: pxa2xx: Fix unlocked snd_pcm_stop() call
ALSA: usx2y: Fix unlocked snd_pcm_stop() call
ALSA: ua101: Fix unlocked snd_pcm_stop() call
ALSA: 6fire: Fix unlocked snd_pcm_stop() call
ALSA: atiixp: Fix unlocked snd_pcm_stop() call
ALSA: asihpi: Fix unlocked snd_pcm_stop() call
sound: oss/vwsnd: Always define vwsnd_mutex
sound: oss/vwsnd: Add missing inclusion of linux/delay.h
ASoC: wm8978: enable symmetric rates
ASoC: omap-mcbsp: Use different method for DMA request when booted with DT
ASoC: omap-dmic: Do not use platform_get_resource_byname() for DMA
ASoC: omap-mcpdm: Do not use platform_get_resource_byname() for DMA
ASoC: omap-pcm: Request the DMA channel differently when DT is involved
ASoC: Samsung: Set RFS and BFS in slave mode
...
Restore debug message lost in merge commit e1b73cba13. Also clarify it
that we are only clamping bpp not overwriting it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The kdump mmap patch series (git commit 83086978c6) changed the
requirements for copy_oldmem_page(). Now this function is used for copying
to virtual memory.
So implement vmalloc support for the s390 version of copy_oldmem_page().
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kdump mmap patch series (git commit 83086978c6) directly
map the PT_LOADs to memory. On s390 this does not work because the
copy_from_oldmem() function swaps [0,crashkernel size] with
[crashkernel base, crashkernel base+crashkernel size]. The swap
int copy_from_oldmem() was done in order correctly implement /dev/oldmem.
See: http://marc.info/?l=kexec&m=136940802511603&w=2
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 variant of 314beb9b "x86: bpf_jit_comp: secure bpf
jit against spraying attacks".
With this change the whole jit code and literal pool will be write
protected after creation. In addition the start address of the jit
code won't be always on a page boundary anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 backend of 79617801 "filter: bpf_jit_comp: refactor
and unify BPF JIT image dump output".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The workqueue workaround is no longer needed. Same as 5199dfe531
"sparc: bpf_jit_comp: can call module_free() from any context".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, fast page fault incorrectly tries to fix mmio page fault when
the generation number is invalid (spte.gen != kvm.gen). It then returns
to guest to retry the fault since it sees the last spte is nonpresent.
This causes an infinite loop.
Since fast page fault only works for direct mmu, the issue exists when
1) tdp is enabled. It is only triggered only on AMD host since on Intel host
the mmio page fault is recognized as ept-misconfig whose handler call
fault-page path with error_code = 0
2) guest paging is disabled. Under this case, the issue is hardly discovered
since paging disable is short-lived and the sptes will be invalid after
memslot changed for 150 times
Fix it by filtering out MMIO page faults in page_fault_can_be_fast.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR0K2gAAoJEHm+PkMAQRiGWsEH+gMZSN1qRm34hZ82q1Tx7HvL
Eb/Gsl3Qw/7G2TlTqgjBUs36IdqV9O2cui/aa3/TfXvdvrx+0GlhRkEwQPc+ygcO
Mvoyoke4tT4+4jVFdCg1J8avREsa28/6oaHs0ZZxuVmJBBLTJH7aXaNsGn6eU1q9
9+p798MQis6naIiPC63somlZcCIiBhsuWCPWpEfLMn8G1HWAFTM3xXIbNBqe/brS
bmIOfhomlIZ5dcdaXGvjtP3+KJhkNDwhkPC4tVYu8JqqgSlrE+a+EGyEuuGqKk10
U+swiqyuD31uBI9ga54u/2FzSqDiAu6YOcMXevjo/m3g9XLdYbYLvN+nvN8alCQ=
=Ob6Z
-----END PGP SIGNATURE-----
Merge tag 'v3.10' into drm-intel-fixes
Backmerge Linux 3.10 to get at
commit 19b2dbde57
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jun 12 10:15:12 2013 +0100
drm/i915: Restore fences after resume and GPU resets
That commit is not in my current -fixes pile since that's based on my
-next queue for 3.11. And the above mentioned fix was merged really
late into 3.10 (and blew up, bad me) so was on a diverging branch.
Option B would have been to rebase my current pile of fixes onto
Dave's drm-fixes branch. But since some of the patches here are a bit
tricky I've decided not to void all the testing by moving over the
entire merge window.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PSR must be enabled after transcoder and port are running.
And it is only available for HSW.
v2: move enable/disable to intel_ddi
v3: The spec suggests PSR should be disabled even before backlight (by pzanoni)
v4: also disabling and enabling whenever panel is disabled/enabled.
v5: make it last patch to avoid breaking whenever bisecting. So calling for
update and force exit came to this patch along with enable/disable calls.
v6: Remove unused and unecessary psr_enable/disable calls, as notice by Paulo.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the psr exit code in the busy ioctl since I didn't merge
that part of the infrastructure yet - it needs more thought.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required function to disable PSR when going to console mode.
But also can be used whenever PSR mode entry conditions changed.
v2: Add it before PSR Hook. Update function not really been called yet.
v3: Fix coding style detected by checkpatch by Paulo Zanoni.
v4: do_enable must be static as Paulo noticed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: prefer seq_puts to seq_printf detected by Paulo Zanoni.
v3: PSR is disabled by default. Without userspace ready it
will cause regression for kde and xdm users
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding support for PSR Status, PSR entry counter and performance counters.
Heavily based on initial work from Shobhit.
v2: Fix PSR Status Link bits by Paulo Zanoni.
v3: Prefer seq_puts to seq_printf by Paulo Zanoni.
v4: Fix identation by Paulo Zanoni.
v5: Return earlier if it isn't Haswell in order to avoid reading non-existing
registers - by Paulo Zanoni.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter