This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a register to the config space for the 460sx. Changes the vc0
detect to a pll detect. maps configuration space to test the link
status. changes the setup to enable gen2 devices to operate at gen2
speeds. fixes mapping that was not correct for the 460sx. added
bit definitions for the OMRxMSKL registers. Removed reserved bit
that was set incorrectly in the OMR2MSKL register.
tested on the 460sx eiger and custom board
Signed-off-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Commit 112d1fe9f7
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.
Move them back out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Instead of using ill-defined numbers (0, 1, and 2) for the monitor port, allow
the user to specify the port by name ("dvi", "lvds", or "dlvds"). This works
on the kernel command line, the module command-line, and the sysfs "monitor"
device.
Note that changing the monitor port does not currently work on the P1022DS,
because the code that talks to the PIXIS FPGA is broken.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the "Checking link..." printk to the function that actually checks the
linke.
Reported-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This renames pci flags functions and enums in preparation for creating
generic version in asm-generic/pci-bridge.h. The following search and
replace is done:
s/ppc_pci_/pci_/
s/PPC_PCI_/PCI_/
Direct accesses to ppc_pci_flag variable are replaced with helper
functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
All current pcie controllers unconditionally use SDR to check the link and
poll for reset. Refactor the code to include device reset in the
port_init_hw() op and add a new check_link() op.
This will make room fro new controllers that do not use SDR for these
operations.
Tested on 460ex.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This lifts the restriction that book3s_hv guests can only run one
hardware thread per core, and allows them to use up to 4 threads
per core on POWER7. The host still has to run single-threaded.
This capability is advertised to qemu through a new KVM_CAP_PPC_SMT
capability. The return value of the ioctl querying this capability
is the number of vcpus per virtual CPU core (vcore), currently 4.
To use this, the host kernel should be booted with all threads
active, and then all the secondary threads should be offlined.
This will put the secondary threads into nap mode. KVM will then
wake them from nap mode and use them for running guest code (while
they are still offline). To wake the secondary threads, we send
them an IPI using a new xics_wake_cpu() function, implemented in
arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage
we assume that the platform has a XICS interrupt controller and
we are using icp-native.c to drive it. Since the woken thread will
need to acknowledge and clear the IPI, we also export the base
physical address of the XICS registers using kvmppc_set_xics_phys()
for use in the low-level KVM book3s code.
When a vcpu is created, it is assigned to a virtual CPU core.
The vcore number is obtained by dividing the vcpu number by the
number of threads per core in the host. This number is exported
to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes
to run the guest in single-threaded mode, it should make all vcpu
numbers be multiples of the number of threads per core.
We distinguish three states of a vcpu: runnable (i.e., ready to execute
the guest), blocked (that is, idle), and busy in host. We currently
implement a policy that the vcore can run only when all its threads
are runnable or blocked. This way, if a vcpu needs to execute elsewhere
in the kernel or in qemu, it can do so without being starved of CPU
by the other vcpus.
When a vcore starts to run, it executes in the context of one of the
vcpu threads. The other vcpu threads all go to sleep and stay asleep
until something happens requiring the vcpu thread to return to qemu,
or to wake up to run the vcore (this can happen when another vcpu
thread goes from busy in host state to blocked).
It can happen that a vcpu goes from blocked to runnable state (e.g.
because of an interrupt), and the vcore it belongs to is already
running. In that case it can start to run immediately as long as
the none of the vcpus in the vcore have started to exit the guest.
We send the next free thread in the vcore an IPI to get it to start
to execute the guest. It synchronizes with the other threads via
the vcore->entry_exit_count field to make sure that it doesn't go
into the guest if the other vcpus are exiting by the time that it
is ready to actually enter the guest.
Note that there is no fixed relationship between the hardware thread
number and the vcpu number. Hardware threads are assigned to vcpus
as they become runnable, so we will always use the lower-numbered
hardware threads in preference to higher-numbered threads if not all
the vcpus in the vcore are runnable, regardless of which vcpus are
runnable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
FSL PCIe controller can act as agent(EP) or host(RC). Under Agent(EP) mode
the controller will be configured by the host system. So its not required
to be registered with the PCI(e) sub-system. We only register the
controller if its configured in host(RC) mode.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add functions to restart and halt the current partition when running under
the Freescale hypervisor. These functions should be assigned to various
function pointers of the ppc_md structure during the .probe() function for
the board:
ppc_md.restart = fsl_hv_restart;
ppc_md.power_off = fsl_hv_halt;
ppc_md.halt = fsl_hv_halt;
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller. This is called the VMPIC.
The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts. External interrupts received by a
partition can come from two sources:
- Hardware interrupts - hardware interrupts come from external
interrupt lines or on-chip I/O devices.
- Virtual interrupts - virtual interrupts are generated by the hypervisor
as part of some hypervisor service or hypervisor-created virtual device.
Both types of interrupts are processed using the same programming model and
same set of hypercalls.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move irq_choose_cpu() into arch/powerpc/kernel/irq.c so that it can be used
by other PIC drivers. The function is not MPIC-specific.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We fixup every FSL PCIe Root Complex we need to fixup a few things.
Rather than adding every device under the sun we move to just matching
only on the vendor (PCI_VENDOR_ID_FREESCALE) and than check that we are
a PCIe controller in host mode in the fixup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The wrong MCSR bit was being used on e500mc. MCSR_BUS_RBERR only exists
on e500v1/v2. Use MCSR_LD on e500mc, and remove all MCSR checking
in fsl_rio_mcheck_exception as we now no longer call that function
if the appropriate bit in MCSR is not set.
If RIO support was enabled at compile-time, but was never probed, just
return from fsl_rio_mcheck_exception rather than dereference a NULL
pointer.
TODO: There is still a remaining, though comparitively minor, issue in
that this recovery mechanism will falsely engage if there's an unrelated
MCSR_LD event at the same time as a RIO error.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support compilation of mpic.c with DEBUG defined, as now we have irq_desc and
not irq number.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sRIO controller reports errors to the core with one signal, it uses
register EPWISR to provides the core quick access to where the error
occurred. The EPWISR indicates that there are 4 interrupts sources,
port1, port2, message unit and port write receive, but the sRIO driver
does not support port2 for now, still the handler takes care of port2.
Currently the handler only clear error status without any recovery.
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for machine_check support into machine_check_e500 and
machine_check_e500mc.
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simultaneous FCM and GPCM or UPM operation may erroneously trigger
bus monitor timeout.
Set the local bus monitor timeout value to the maximum by setting
LBCR[BMT] = 0 and LBCR[BMTPS] = 0xF.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (34 commits)
PM: Introduce generic prepare and complete callbacks for subsystems
PM: Allow drivers to allocate memory from .prepare() callbacks safely
PM: Remove CONFIG_PM_VERBOSE
Revert "PM / Hibernate: Reduce autotuned default image size"
PM / Hibernate: Add sysfs knob to control size of memory for drivers
PM / Wakeup: Remove useless synchronize_rcu() call
kmod: always provide usermodehelper_disable()
PM / ACPI: Remove acpi_sleep=s4_nonvs
PM / Wakeup: Fix build warning related to the "wakeup" sysfs file
PM: Print a warning if firmware is requested when tasks are frozen
PM / Runtime: Rework runtime PM handling during driver removal
Freezer: Use SMP barriers
PM / Suspend: Do not ignore error codes returned by suspend_enter()
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
...
Add support for MPIC timers as requestable interrupt sources.
Based on http://patchwork.ozlabs.org/patch/20941/ by Dave Liu.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some irq_host implementations are using virq_to_host to check if
they are the irq_host for a virtual irq. To allow us to make space
versus time tradeoffs, replace this usage with an assertive
virq_is_host that confirms or denies the irq is associated with the
given irq_host.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
handler_data should be reserved for flow handlers on the dependent
irq, not consumed by the parent irq code that is part of the irq_chip
code. The msi_data pointer was already set in msidesc->irqhost->hostdata
and being copied to irq_data->chipdata in the msidesc->irqhost->map()
method called via create_irq_mapping, so we can obtain the pointer
from there and free the instance it in teardown_msi_irqs.
Also remove the unnecessary cast of irq_get_handler_data in the
cascade handler, which is the demux flow handler of the parent
msi interrupt. (This is the expected usage for handler_data).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The msi platform device driver was abusing dev.platform_data for its
platform_driver_data. Use the correct pointer for storage.
Platform_data is supposed to be for platforms to communicate to drivers
parameters that are not otherwise discoverable. Its lifetime matches
the platform_device not the platform device driver. It is generally
not needed for drivers that only support systems with device trees.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was never called because the host is always IRQ_HOST_MAP_LEGACY.
And what it purported to do was mask the interrupt (which will already
have happend if we shutdown the interrupt), then synchronise_irq and
clear the chip pointer, both of which will have been be done by the
caller were we to call unmap on a legacy irq.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we already have a special case in map to set the ipi handler, use
the desired flow.
If we don't find an ics to handle the interrupt complain instead of
returning 0 without having set a chip or handler.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compile the new smp ipi mux and demux code only if a platform
will make use of it. The new config is selected as required.
The new cause_ipi smp op is only available conditionally to point out
configs where the select is required; this makes setting the op an
immediate fail instead of a deferred unresolved symbol at link.
This also creates a new config for power surge powermac upgrade support
that can be disabled in expert mode but is default on.
I also removed the depends / default y on CONFIG_XICS since it is selected
by PSERIES.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that MSG_ALL and MSG_ALL_BUT_SELF have been eliminated,
smp_mpic_mesage_pass no longer needs to lookup the cpumask just to
have mpic_send_ipi extract part of it and recode it in a NR_CPUS loop
by mpic_physmask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that smp_ops->smp_message_pass is always called with an (online) cpu
number for the target remove the checks for MSG_ALL and MSG_ALL_BUT_SELF.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_set_affinity is allocating and freeing a cpumask var even though
it was breaking the cpumask abstraction when passing the mask to
mpic_physmask. It also didn't have any check for allocatin failure.
Break the cpumask abstraction earlier and use simple bitwise and of the
bits from the mask with the bits of cpu_online_mask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_physmask was looping NR_CPUS times over a mask that was passed as
a u32. Since mpic is architecturaly limited to 32 physical cpus, clamp
the logical cpus to 32 when compiling (we could also clamp at runtime
to nr_cpu_ids).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a confusing number of ioremap functions. Make things just a
bit simpler by merging ioremap_flags and ioremap_prot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make some PowerPC architecture's code use struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a platform for the Wire Speed Processor, based on the PPC A2.
This includes code for the ICS & OPB interrupt controllers, as well
as a SCOM backend, and SCOM based cpu bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As well as searching for nodes with type = "nvram", search for nodes
that have compatible = "nvram". This can't be converted into a single
call to of_find_compatible_node() with a non-NULL type, because that
searches for a node that has _both_ type & compatible = "nvram".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An upcoming new ics backend will need to implement different matching
semantics to the current ones, which are essentially the RTAS ics
backends. So move the current match into the RTAS backend, and allow
other ics backends to override.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when nothing is specified in the device tree, and despite the
fact that we don't setup links properly yet, we still need a reasonable
value in there or some interrupts won't be setup properly to point to
an existing processor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCIe nodes with the property status="disabled" are not usable and so
avoid adding "disabled" PCIe bridge with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates the LEVEL flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates IRQ_LEVEL.
Use irq_data to get the level type information in the chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Retrieve the IRQ_LEVEL information from irq_data which avoids a
redundant sparse irq lookup as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The level flag is
updated in the core as well.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core code provides the same functionality when the
IRQCHIP_EOI_IF_HANDLED flag is set for the irq chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Removes resource reservation from the common sybsystem initialization code
and make it part of mport driver initialization. This resolves conflict
with resource reservation by device specific mport drivers.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes mport ID and host destination ID assignment to implement unified
method common to all mport drivers. Makes "riohdid=" kernel command line
parameter common for all architectures with support for more that one host
destination ID assignment.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem initialization sequence modified to support presence of multiple
RapidIO controllers in the system. The new sequence is compatible with
initialization of PCI devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of patches eliminates RapidIO dependency on PowerPC architecture
and makes it available to other architectures (x86 and MIPS). It also
enables support of new platform independent RapidIO controllers such as
PCI-to-SRIO and PCI Express-to-SRIO.
This patch:
Extend number of mport callback functions to eliminate direct linking of
architecture specific mport operations.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following code snippet:
unsigned int cpu = 0;
if (mpic->flags & MPIC_PRIMARY)
cpu = hard_smp_processor_id();
is seen in several places in the 'mpic.c' code. This changeset factors
that pattern out into a helper function called 'mpic_processor_id'.
Signed-off-by: Meador Inge <meador_inge@mentor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This property, defined in the Open PIC binding, tells the kernel not to use
the reset bit in the global configuration register. Additionally, its
presence mandates that only sources which are actually used (i.e. appear in
the device tree) should have their VECPRI bits initialized.
Although, "pic-no-reset" can be used for the same use cases that
"protected-sources" is covering, the "protected-sources" implementation was
left completely intact. This is a more pragmatic approach as there are
already several existing systems which use protected sources. If
"pic-no-reset" *and* "protected-sources" are both used, however, then
"pic-no-reset" takes precedence in terms of the init behavior and the
sanity checks done by protected sources will still take place.
Signed-off-by: Meador Inge <meador_inge@mentor.com>
Cc: Hollis Blanchard <hollis_blanchard@mentor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
sram_params.sram_size and sram_params.sram_offset were unsigned.
If get_cache_sram_size() or get_cache_sram_offset() returns error code
then it is not seen to the caller. Made sram_size and sram_offset signed.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now handles multiple ranges, doesn't make assumptions about interrupt
specifier format, and doesn't claim interrupts that don't correspond to an
available range.
Also has some better error checking.
The device tree binding is updated to clarify some existing assumptions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit da3ed89e7c added
'fsl,qoriq-gpio' compatiable searching in the old way
using for_each_compatible_node(). But the driver have
previously been changed to use a struct of_device_id
compatible list passed to for_each_matching_node().
Add 'fsl,qoriq-gpio' compatiable to the existing
compatible list instead of adding another
for_each_compatible_node() loop.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new config and interrupt Status register to struct ccsr_pci & updated
pit_t array size to reflect the 4 inbound windows.
Device tree is used to maintain backward compatibility i.e. update inbound
window 1 index depending upon "compatible" field witin PCIE node.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Benjamin Herrenschmidt