When a failure to stop a module in the pipeline is detected, the only
way to recover is to reset the ISP. However, as other users can be using
a different pipeline with other modules, the ISP can't be reset
synchronously with the error detection.
Mark the ISP as needing a reset when a failure to stop a pipeline is
detected, and reset the ISP when the last user releases the last
reference to the ISP.
Modify the omap3isp_pipeline_set_stream() function to record the new ISP
pipeline state only when no error occurs, except when stopping the
pipeline in which case the pipeline is still marked as stopped.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct ispstat_generic_config's comments refers to isph3a_aewb_config,
isph3a_af_config and isphist_config. But those structs have had their
names prefixed with 'omap3'. So, let's update the comments.
Signed-off-by: David Cohen <david.cohen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It doesn't get more trivial than these.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Round properly the rsz factor so that we get highest rsz so that the input
width (or height) is highest possible smaller or equal to what the user
asks.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the number of phases/taps, used to select the correct equations to
compute the ratio, depends on the ratio, start with the 7-tap mode
equations to compute an approximation of the ratio, and switch to the
4-tap mode equations if the approximation is lower than or equal to 512.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the crop rectangle needs to be modified to match hardware
requirements, center the resulting rectangle on the requested rectangle
instead of removing pixels from the right and bottom sides only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit
379fa5d ([media] V4L: mx3_camera: convert to videobuf2)
mx3_camera uses videobuf2, but that commit didn't upgrade the select
resulting in the following build failure:
drivers/built-in.o: In function `mx3_camera_init_videobuf':
clkdev.c:(.text+0x86580): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx3_camera_probe':
clkdev.c:(.devinit.text+0x3548): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x3578): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx3_camera_remove':
clkdev.c:(.devexit.text+0x674): undefined reference to `vb2_dma_contig_cleanup_ctx'
make[2]: *** [.tmp_vmlinux1] Error 1
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera host driver (sh_mobile_ceu_camera.c) is unloaded and then
reloaded, probe will fail, because camera client .set_bus_param() and
.query_bus_param() methods have been set to NULL. Fix this by caching
the original pointers and restoring them on driver-unbind.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_unregister_device() frees the I2C client, so, dereferencing it
afterwards is a bug, that leads to Oopses.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of CSI2 support on sh-mobile, the host driver
switched to using v4l2_device_call_until_err() with grp_id == 0 to
call subdev operations on the sensor and the CSI2 subdev. However,
this has broken multi-client set ups like the one on migor, because
that way all operations get called on both clients. To fix this add
a grp_id and set it to the client private context.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
buf->size is not yet initialised in videobuf2-dma-contig at the time of
the error message, use "size."
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf2-dma-contig allocator returns an ERR_PTR() on failure, not
a NULL like all other allocators. Fix videobuf2-core to also correctly
recognise those failures.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If allocating stream buffers for one of the primary streams (e.g. YUV)
failed during card probe, the error path clean up would try to manipulate
the yet unitialized IDX stream structures. This caused a BUG due to
unitialized list heads.
Detect that case and ignore the uninitialized IDX stream.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
dma_addr_t may not fit into void* on some architectures. To be safe, make
vb2_dma_contig_cookie() return a pointer to dma_addr_t and dereference it
in vb2_dma_contig_plane_paddr() back to dma_addr_t.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use vb2_dma_contig_plane_paddr to retrieve a physical address for a plane
instead of calling an internal mem_ops callback.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The soc-camera core accesses the "pix" member of the struct v4l2_format::fmt
union, which is only valid for V4L2_BUF_TYPE_VIDEO_CAPTURE streams. This
patch adds explicit checks for this to {g,s,try}_fmt methods.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the problem in which a host driver
sets a personalized sizeimage or bytesperline field,
and gets ignored when doing G_FMT.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hdpvr's IR part, in short, sucks. As observed with a usb traffic
sniffer, the Windows software for it uses a polling interval of 405ms.
Its still not behaving as well as I'd like even with this change, but
this inches us closer and closer to that point...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new hauppauge key tables use both device code button code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This keymap were used for the Hauppauge Black remote controller
only. It also contains some keycodes not found there. As the
Hauppauge Black is now part of the hauppauge keymap, just remove
it.
Also, remove the modprobe hacks to select between the Gray
and the Black versions of the remote controller as:
- Both are supported by default by the keymap;
- If the user just wants one keyboard supported,
it is just a matter of changing the keymap via
the userspace tool (ir-keytable), removing
the keys that he doesn't desire. As ir-keytable
auto-loads the keys via udev, this is better than
obscure modprobe parameters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Make the hdpvr's i2c master implementation more closely mirror that of
the pvrusb2 driver. Currently makes no significant difference in IR
reception behavior with ir-kbd-i2c (i.e., it still sucks).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the code in saa7134-input is not a module, but the config for it is
set as a boolean instead of a tristate, this causes a strange dependency
on RC_CORE.
VIDEO_SAA7134_RC (which determines if saa7134-input.o is built) depends
on RC_CORE and VIDEO_SAA7134. If VIDEO_SAA7134 is compiled as 'y' but
RC_CORE is compiled as 'm' VIDEO_SAA7134_RC can still be set to 'y'
which causes undefined symbols that it needs from RC_CORE.
The simplest solution is to not allow VIDEO_SAA7134_RC be enabled if
RC_CORE compiled as a module (m) and VIDEO_SA7134 is compiled into the
kernel (y).
Suggested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kbuild <linux-kbuild@vger.kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a bug in gspca, more precisely in alt_xfer().
This function looks for an input transfer endpoint in an alternate setting.
By default it returns the first endpoint corresponding to the transfer type
indicated in parameter.
But with some USB devices, the first endpoint corresponding to the transfer
type is not always an INPUT endpoint but an OUTPUT one.
This patch adds the endpoint direction test to be sure to return an INPUT endpoint
Signed-off-by: Patrice CHOTARD <patricechotard@free.fr>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No 352x288 for Ds3303 and no 320x240 for Generic802.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than guess which driver supports core priority handling, require drivers
that do to explicitly set the V4L2_FL_USE_FH_PRIO flag in video_device.
Updated the core prio handling accordingly and set the flag in the three
drivers that do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv-ioctl cast the 'void *fh' directly to 'ivtv_open_id *'. This should be
done properly with a contained_of since the 'void *fh' is really a
'struct v4l2_fh *'.
It worked because the v4l2_fh field is also the first field in the ivtv_open_id
struct, but it is not clean code.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device struct has proper ref counting and its release function
will be called when the last user releases it. But no such support was
available for struct v4l2_device. This made it hard to determine when a
USB driver can release the device if it has multiple device nodes.
With one device node it is easy of course, since when the device node is
released, the whole device can be released.
This patch adds refcounting to v4l2_device. When registering device nodes
the v4l2_device refcount will be increased, when releasing device nodes
it will be decreased. The (optional) release function will be called when
the last device node was released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S/G_PRIORITY handling is now done by the v4l2 core framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_fh can now use the core framework support of g/s_priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several drivers need to do something when the first filehandle is opened
or the last filehandle is closed. Most implement some use count mechanism,
but if they use v4l2_fh, then you can also just check if this is the only
filehandle for the device node. A simple helper function can do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new functions: v4l2_fh_open allocates and initializes a struct v4l2_fh
based on a struct file pointer and v4l2_fh_release releases and frees a struct
v4l2_fh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab