Remove a little bit of unnecessary work when transmitting a packet with
neigh_packet_xmit. Use the neighbour table index not the address family
as a parameter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the OPENVSWITCH Kconfig option and old Kconfigs by having
OPENVSWITCH select both NET_MPLS_GSO and MPLSO.
A Kbuild test robot reported that when NET_MPLS_GSO is selected by
OPENVSWITCH the generated .config is broken because MPLS is not
selected.
Cc: Simon Horman <horms@verge.net.au>
Fixes: cec9166ca4 mpls: Refactor how the mpls module is built
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC3032 section 2.4.2 packets with an outgoing
ttl of 0 MUST NOT be forwarded. According to section 2.4.1
an outgoing TTL of 0 comes from an incomming TTL <= 1.
Therefore any packets that is received with a ttl <= 1 should
not have it's ttl decremented and forwarded.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse was generating a lot of warnings mostly from missing annotations
in the code. Add missing annotations and in a few cases tweak the code
for performance by moving work before loops.
This also fixes a problematic ommision of rcu_assign_pointer and
rcu_dereference.
Hopefully with complete rcu annotations any new rcu errors will stick
out like a sore thumb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*Blink* I got the argument order wrong to kzalloc and the
code was working properly when tested. *Blink*
Fix that.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers use copybreak to copy tiny frames into smaller skb,
and this smaller skb might not have skb->head_frag set for various
reasons.
skb_gro_receive() currently doesn't allow to aggregate the smaller skb
into the previous GRO packet if this GRO packet has at least 2 MSS in
it.
Following workload easily demonstrates the problem.
netperf -t TCP_RR -H target -- -r 3000,3000
(tcpdump shows one GRO packet with 2 MSS, plus one additional packet of
104 bytes that should have been appended.)
It turns out that we can remove code from skb_gro_receive(), because
commit 8a29111c7c ("net: gro: allow to build full sized skb") and its
followups removed the assumption that a GRO packet with a frag_list had
to have an empty head.
Removing this code allows the aggregation of the last (incomplete) frame
in some RPC workloads. Note that tcp_gro_receive() already takes care of
forcing a flush if necessary, including this case.
If we want to avoid using frag_list in the first place (in forwarding
workloads for example, as the outgoing NIC is generally not able to cope
with skbs having a frag_list), we need to address this separately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in 802.1Qau spec. Add this optional attribute to the
DCB netlink layer. To allow for application to use the new attribute,
NIC drivers should implement and register the callbacks ieee_getqcn,
ieee_setqcn and ieee_getqcnstats.
The QCN attribute holds a set of parameters for management, and
a set of statistics to provide informative data on Congestion-Control
defined by this spec.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the root of the trie contains a key_vector, by
doing this we make room to essentially collapse the entire trie by at least
one cache line as we can store the information about the tnode or leaf that
is pointed to in the root.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the parent pointer from the key_vector and places it in
the tnode structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pulls the information about the child array out of the key_vector and
places it in the tnode since that is where it is needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU is only needed once for the entire node, not once per key_vector so we
can pull that out and move it to the tnode structure.
In addition add accessors to be used inside the RCU functions so that we
can more easily get from the key vector to either the tnode or the trie
pointers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the fields not explicitly needed in the key_vector and
placed them in the new tnode structure. By doing this we will eventually
be able to reduce the key_vector down to 16 bytes on 64 bit systems, and
12 bytes on 32 bit systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are now checking the length of a key_vector instead of a tnode so it
makes sense to probably just rename this to child_length since it would
probably even be applicable to a leaf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am replacing the tnode_get_child call with get_child since we are
techically pulling the child out of a key_vector now and not a tnode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tnode to key_vector. The key_vector will be the eventual
container for all of the information needed by either a leaf or a tnode.
The final result should be much smaller than the 40 bytes currently needed
for either one.
This also updates the trie struct so that it contains an array of size 1 of
tnode pointers. This is to bring the structure more inline with how an
actual tnode itself is configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resize related functions now all return a pointer to the pointer that
references the object that was resized.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change just does a couple of minor cleanups on
fib_table_flush_external. Specifically it addresses the fact that resize
was being called even though nothing was being removed from the table, and
it drops an unecessary indent since we could just call continue on the
inverse of the fi && flag check.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the nla length is less than 2 then the nla data could be accessed
beyond the accessible bounds. So ensure that the nla is big enough to
at least read the via_family before doing so. Replace magic value of
2.
Fixes: 03c0566542 ("mpls: Basic support for adding and removing routes")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC4821 7.3. Selecting Probe Size, a probe timer should
be armed once probing has converged. Once this timer expired,
probing again to take advantage of any path PMTU change. The
recommended probing interval is 10 minutes per RFC1981. Probing
interval could be sysctled by sysctl_tcp_probe_interval.
Eric Dumazet suggested to implement pseudo timer based on 32bits
jiffies tcp_time_stamp instead of using classic timer for such
rare event.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current probe_size is chosen by doubling mss_cache,
the probing process will end shortly with a sub-optimal
mss size, and the link mtu will not be taken full
advantage of, in return, this will make user to tweak
tcp_base_mss with care.
Use binary search to choose probe_size in a fine
granularity manner, an optimal mss will be found
to boost performance as its maxmium.
In addition, introduce a sysctl_tcp_probe_threshold
to control when probing will stop in respect to
the width of search range.
Test env:
Docker instance with vxlan encapuslation(82599EB)
iperf -c 10.0.0.24 -t 60
before this patch:
1.26 Gbits/sec
After this patch: increase 26%
1.59 Gbits/sec
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other users users of the neighbour table use neigh->output as the method
to decided when and which link-layer header to place on a packet.
DECnet has been using neigh->output to decide which DECnet headers to
place on a packet depending which neighbour the packet is destined for.
The DECnet usage isn't totally wrong but it can run into problems if the
neighbour output function is run for a second time as the teql driver
and the bridge netfilter code can do.
Therefore to avoid pathologic problems later down the line and make the
neighbour code easier to understand by refactoring the decnet output
code to only use a neighbour method to add a link layer header to a
packet.
This is done by moving the neigbhour operations lookup from
dn_to_neigh_output to dn_neigh_output_packet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/fib_trie.c: In function ‘fib_table_flush_external’:
net/ipv4/fib_trie.c:1572:6: warning: unused variable ‘found’ [-Wunused-variable]
int found = 0;
^
net/ipv4/fib_trie.c:1571:16: warning: unused variable ‘slen’ [-Wunused-variable]
unsigned char slen;
^
Signed-off-by: David S. Miller <davem@davemloft.net>
Call into the switchdev driver any time an IPv4 fib entry is
added/modified/deleted from the kernel's FIB. The switchdev driver may or
may not install the route to the offload device. In the case where the
driver tries to install the route and something goes wrong (device's routing
table is full, etc), then all of the offloaded routes will be flushed from the
device, route forwarding falls back to the kernel, and no more routes are
offloading.
We can refine this logic later. For now, use the simplist model of offloading
routes up to the point of failure, and then on failure, undo everything and
mark IPv4 offloading disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flesh out ndo wrappers to call into device driver. To call into device driver,
the wrapper must interate over route's nexthops to ensure all nexthop devs
belong to the same switch device. Currently, there is no support for route's
nexthops spanning offloaded and non-offloaded devices, or spanning ports of
multiple offload devices.
Since switch device ports may be stacked under virtual interfaces (bonds and/or
bridges), and the route's nexthop may be on the virtual interface, the wrapper
will traverse the nexthop dev down to the base dev. It's the base dev that's
passed to the switchdev driver's ndo ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep switchdev FIB offload model simple for now and don't allow custom ip
rules.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 fib ndo wrapper funcs and stub them out for now.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the core logic that setups a 'struct dsa_switch_tree' and
removes it, update dsa_probe() and dsa_remove() to use the two helper
functions. This will be useful to allow for other callers to setup
this structure differently.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support the new DSA device driver model, a dsa_switch should
be able to advertise the type of tagging protocol supported by the
underlying switch device. This also removes constraints on how tagging
can be stacked to each other.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the part of dsa_switch_setup() which is responsible for allocating
and initializing a 'struct dsa_switch' and the part which is doing a
given switch device setup and slave network device creation.
This is a preliminary change to allow a separate caller of
dsa_switch_setup_one() which may have externally initialized the
dsa_switch structure, outside of dsa_switch_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different model to register DSA switches,
update dsa_of_probe() and dsa_probe() to return -EPROBE_DEFER where
appropriate.
Failure to find a phandle or Device Tree property is still fatal, but
looking up the internal device structure associated with a Device Tree
node is something that might need to be delayed based on driver probe
ordering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timewait sockets now share a common base with established sockets.
inet_twsk_diag_dump() can use inet_diag_bc_sk() instead of duplicating
code, granted that inet_diag_bc_sk() does proper userlocks
initialization.
twsk_build_assert() will catch any future changes that could break
the assumptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip/udp bearer can be configured in a point-to-point
mode by specifying both local and remote ip/hostname,
or it can be enabled in multicast mode, where links are
established to all tipc nodes that have joined the same
multicast group. The multicast IP address is generated
based on the TIPC network ID, but can be overridden by
using another multicast address as remote ip.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The payload area following the TIPC discovery message header is an
opaque area defined by the media. INT_H_SIZE was enough for
Ethernet/IB/IPv4 but needs to be expanded to carry IPv6 addressing
information.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build error:
net/mpls/af_mpls.c: In function 'resize_platform_label_table':
net/mpls/af_mpls.c:767:4: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
labels = vzalloc(size);
^
Fixes: 7720c01f3f ("mpls: Add a sysctl to control the size of the mpls label table")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to prevent us from attempting to allocate a tnode with
a size larger than what can be represented by size_t.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the fib_table_lookup function so that it is in sync
with the fib_find_node function in terms of the explanation for the index
check based on the bits value.
I have also updated it from doing a mask to just doing a compare as I have
found that seems to provide more options to the compiler as I have seen it
turn this into a shift of the value and test under some circumstances.
In addition I addressed one minor issue in which we kept computing the key
^ n->key when checking the fib aliases. I pulled the xor out of the loop
in order to reduce the number of memory reads in the lookup. As a result
we should save a couple cycles since the xor is only done once much earlier
in the lookup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib_table was wrapped in several places with an
rcu_read_lock/rcu_read_unlock however after looking over the code I found
several spots where the tables were being accessed as just standard
pointers without any protections. This change fixes that so that all of
the proper protections are in place when accessing the table to take RCU
replacement or removal of the table into account.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are going to compact the leaf and tnode we first need to make sure
the fields are all in the same place. In that regard I am moving the leaf
pointer which represents the fib_alias hash list to occupy what is
currently the first key_vector pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the insert and delete functions make use of
the tnode pointer returned in the fib_find_node call. By doing this we
will not have to rely on the parent pointer in the leaf which will be going
away soon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the parent pointer is returned by reference in
fib_find_node. By doing this I can use it to find the parent node when I
am performing an insertion and I don't have to look for it again in
fib_insert_node.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that leaf_walk_rcu takes a tnode and a key instead
of the trie and a leaf.
The main idea behind this is to avoid using the leaf parent pointer as that
can have additional overhead in the future as I am trying to reduce the
size of a leaf down to 16 bytes on 64b systems and 12b on 32b systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we only call resize on the tnodes, instead of
from each of the leaves. By doing this we can significantly reduce the
amount of time spent resizing as we can update all of the leaves in the
tnode first before we make any determinations about resizing. As a result
we can simply free the tnode in the case that all of the leaves from a
given tnode are flushed instead of resizing with each leaf removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman