The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.
[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
Now that u5500 is obsolete, u8500 is the only user of the Nomadik
i2c driver. As such there is no requirement to differentiate between
initialisation values. By the time a new SoC is released, almost all
of the ux500 platform will be DT:ed, so we can make decisions based
on the compatible property instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The i2c-nomadik gateware is really a PrimeCell APB device. By hosting
the driver under the amba bus we can access it more easily, for
example using the generic pci-amba driver. The patch also fixes the
mach-ux500 users, so they register an amba device instead than a
platform device.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The header and driver are only used by arm/mach-u8500 (and potentially
arm/mach-nomadik), but the STA2X11 I/O Hub exports on PCIe a number of
devices, including i2c-nomadik. This patch allows compilation of the
driver under x86.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This fixes a number of whitespace and punctuation problems
around the Nomadik I2C driver.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There was a missing struct item in the kerneldoc, add it and fix
another pretty-printing formatting issue with a missing space.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If there is a signal pending and wait_for_completion_interruptible_timeout
exited because of the -ERESTARTSYS error we are unable to send any more
i2c messages.
So, deprecate this _interruptible_ variant call.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.
2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus/i2c-2638' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: move setup to the earlier subsys initcall
i2c-bfin-twi: handle faulty slave devices better
i2c-mv64xxx: send repeated START between messages in xfer
i2c-nomadik: fix regression on adapter name
i2c-omap: Set latency requirements only once for several messages
i2c-eg20t: add driver for Intel EG20T
i2c-ocores: add some device tree documentation
i2c-ocores: Use devres for resource allocation
i2c-ocores: Adapt for device tree
i2c-iop3xx: add iomem annotation
The Nomadik I2C adapter does not provide a name for the struct
passed into i2c_add_numbered_adapter() causing a regression on
2.6.37-rc3 due to commit 2236baa75f
adding sanity checks for adapters. Fix this by providing a name
proper.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We were missing a transfer delay in one execution path leading to
hangs and the bus timeout was too low leading to errors under
stress tests.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We can do smbus emulation so flag this and drop the duplicate
flags implied from smbus emulation.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This makes sure the Nomadik I2C bus driver silicon is only clocked
when really needed, saving some microamps here and there when
there is no I2C traffic.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This fixes some kerneldoc and assorted documenatation in the
Nomadik I2C driver without semantic impact.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix this warning:
i2c-nomadik.c:707: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~'
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
So that the module can be loaded again after an unload.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This adds support for ST-Ericsson's I2C block found
in Ux500 and Nomadik 8815 platforms.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Chuansheng Liu