Move the definition of DM64XX_VDD3P3V_PWDN from hardware.h
to devices.c since it is used only there.
This also helps rid hardware.h of platform private stuff.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Rather than each platform providing its own function to adjust the
zone sizes, use the new ARM_DMA_ZONE_SIZE definition to perform this
adjustment. This ensures that the actual DMA zone size and the
ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS definitions are consistent with
each other, and moves this complexity out of the platform code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The values of ISA_DMA_THRESHOLD and MAX_DMA_ADDRESS are related; one is
the physical/bus address, the other is the virtual address. Both need
to be kept in step, so rather than having platforms define both, allow
them to define a single macro which sets both of these macros
appropraitely.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simple conversion which simply uses the fact that the second irq chip
base address has offset 0x04 to the first one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Move DA8XX_MMCSD0_BASE, DA8XX_LCD_CNTRL_BASE, and DA8XX_DDR2_CTL_BASE from
<mach/da8xx.h> to devices-da8xx.c as the latter file is the only place where
these macros are used.
While at it, restore sorting the base address macros by address value in
devices-da8xx.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Commit 044ca01521 (davinci: da850/omap-l138: add
support for SoC suspend) introduced DA8XX_PLL1_BASE despite PLL1 exists only on
DA850/OMAP-L138 and da850.c even already #define'd DA850_PLL1_BASE. Kill the
duplicate macro, renaming an existing reference to it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
DA8XX_GPIO_BASE is #define'd in both <mach/da8xx.h> and devices-da8xx.c;
moreover, it's not even used in the latter file...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: (47 commits)
CLKDEV: Fix clkdev return value for NULL clk case
ARM: 6891/1: prevent heap corruption in OABI semtimedop
ARM: kprobes: Tidy-up kprobes-decode.c
ARM: kprobes: Add emulation of hint instructions like NOP and WFI
ARM: kprobes: Add emulation of SBFX, UBFX, BFI and BFC instructions
ARM: kprobes: Add emulation of MOVW and MOVT instructions
ARM: kprobes: Reject probing of undefined data processing instructions
ARM: kprobes: Remove redundant code in space_1111
ARM: kprobes: Fix emulation of PLD instructions
ARM: kprobes: Reject probing of SETEND instructions
ARM: kprobes: Consolidate stub decoding functions
ARM: kprobes: Reject probing of all coprocessor instructions
ARM: kprobes: Fix emulation of USAD8 instructions
ARM: kprobes: Fix emulation of SMUAD, SMUSD and SMMUL instructions
ARM: kprobes: Fix emulation of SXTB16, SXTB, SXTH, UXTB16, UXTB and UXTH instructions
ARM: kprobes: Reject probing of undefined media instructions
ARM: kprobes: Add emulation of RBIT instruction
ARM: kprobes: Reject probing of LDRB instructions which load PC
ARM: kprobes: Fix emulation of LDRD and STRD instructions
ARM: kprobes: Reject probing of LDR/STR instructions which update PC unpredictably
...
Several Davinci platforms select the I2C EEPROM support, but don't
select I2C support. This causes I2C EEPROM support to be built into
the kernel, but I2C support may not be configured to be built in.
This leads to linker errors due to missing I2C symbols.
Arrange for I2C to be selected whenever EEPROM_AT24 is selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 54ce6883d2 (davinci: da8xx: add spi
resources and registration routine) wrongly assumed that SPI1 is mapped at
the same address on DA830/OMAP-L137 and DA850/OMAP-L138; actually, the base
address was valid only for the latter SoC. Teach the code to pass the correct
SPI1 memory resource for both SoCs...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Current board configurations involving the MityDSP-L138 and MityARM-1808
only have one attached PHY, but it's address may not be the same. Default
the behavior to auto-probe for the PHY and use the first one found.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For the MityDSP-L138/MityARM-1808 SOMS, the NAND controller id (which needs
to correspond to the chipselect, and is used for controlling the HW ECC
computation) is not correct. Fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fixup davinci UART low-level debug code for new ARM generic p2v changes.
Based on OMAP changes by Tony Lindgren
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make use of the new functionality which ensures that irq_set_type is
called with the chip masked. Unmask is only done when the interrupt is
not disabled.
Retrieve the trigger type from irq_data in unmask
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 73b089b052 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code. Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds definitions for spi devices on the tnetv107x evm platform.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds an SSP platform device definition for the tnetv107x soc family.
The clock lookup entry has also been updated to match.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 75e2ea643f (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add spi clock information for da850.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The spi driver name called out for the da830 spi clock list is not correct,
fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Extract magic numbers from DMA resource initializers to #defines.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The DA830_edma_ch enum set is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix below section mismatch warning:
WARNING: vmlinux.o(.data+0x673c): Section mismatch in reference from the variable davinci_driver to the function .init.text:davinci_cpu_init()
The variable davinci_driver references
the function __init davinci_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 6d803ba736 (ARM: 6483/1: arm & sh:
factorised duplicated clkdev.c) caused the following warnings:
In file included from /home/headless/src/kernel.org/linux-davinci/arch/arm/
include/asm/clkdev.h:17,
from include/linux/clkdev.h:15,
from arch/arm/mach-davinci/clock.h:71,
from arch/arm/mach-davinci/common.c:22:
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: `struct clk' declared
inside parameter list
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/mach-davinci/include/mach/clkdev.h:9: warning: `struct clk' declared
inside parameter list
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850 uart pinmux arrays are not used. Remove them.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mmcsd0_pins pinmux array contains pins that are specific to the
da850 evm board (the write protect and card detect GPIO pins). Move
the array to the board file.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mcasp_pins pinmux array is specific to the da850_evm, and is
not generic. Move the array to the board file, make it static initdata,
and rename it accordingly.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_emif25_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_cpgmac_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For the MityDSP-L138/MityARM-1808 SoMs, the speed grade can be determined
from the part number string read from the factory configuration block on
the on-board I2C PROM. Configure the maximum CPU speed based on this
information.
This patch was tested using a MityDSP-L138 and MityARM-1808 at various
speedgrades. Also, for code coverage, a bogus configuration was tested
as well as a configuration having an unknown part number.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
From: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
The JTAG variant code for Rev-2.0 silicon of the OMAP-L138 has changed.
In addition, the variant code for the AM-1808 SoC appears to match
the Rev-2.0 code for the OMAP-L138. Add an additional entry to support
these chips.
This patch is originally from a patch on the arago project, here:
http://arago-project.org/git/projects/?p=linux-omapl1.git;a=commit;h=6157618435e313a444cdf059702bd34036a6e2b7
Further information related to the need for this patch can be located at
http://e2e.ti.com/support/embedded/f/354/p/67290/248486.aspxhttp://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-November/021224.html
This patch was tested using an AM-1808 SoC on a MityARM-1808 SoM card. It
was also tested using a Rev 1.0 silicon OMAP-L138 on a MityDSP-L138F card.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reported-by: Nicolas Luna <luna.id@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MMC/SD support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EDMA support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EMAC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch fix a bug in the register indexing for GPIOs numbers > 31
to get the relevant hardware registers of tnetv107x to control the GPIOs.
In the structure tnetv107x_gpio_regs:
struct tnetv107x_gpio_regs {
u32 idver;
u32 data_in[3];
u32 data_out[3];
u32 direction[3];
u32 enable[3];
};
The GPIO hardware register addresses of tnetv107x are stored.
The chip implements 3 registers of each entity to serve 96 GPIOs,
each register provides a subset of 32 GPIOs.
The driver provides these macros: gpio_reg_set_bit, gpio_reg_get_bit
and gpio_reg_clear_bit.
The bug implied the use of macros to access the relevant hardware
register e.g. the driver code used the macro like this:
'gpio_reg_clear_bit(®->data_out, gpio)'
But it has to be used like this:
'gpio_reg_clear_bit(reg->data_out, gpio)'.
The different results are shown here:
- ®->data_out + 1 (it will add the full array size of data_out i.e. 12 bytes)
- reg->data_out + 1 (it will increment only the size of data_out i.e. only 4 bytes)
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Hirosh Dabui <hirosh.dabui@snom.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
After the multi-component commit f0fba2ad (ASoC: multi-component - ASoC
Multi-Component Support) for ASoC, we need to register the platform
device for davinci-pcm-audio.
This patch and patch at [1] are required for audio to work on
DA850/OMAP-L138.
[1] https://patchwork.kernel.org/patch/495211/
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
spi: davinci: fix checkpatch errors
spi: davinci: whitespace cleanup
spi: davinci: remove unused variable 'pdata'
spi: davinci: set chip-select mode in SPIDEF only once
spi: davinci: enable both activation and deactivation of chip-selects
spi: davinci: remove unnecessary data transmit on CS disable
spi: davinci: enable GPIO lines to be used as chip selects
spi: davinci: simplify prescalar calculation
spi: davinci: remove 'wait_enable' platform data member
spi: davinci: make chip-slect specific parameters really chip-select specific
spi: davinci: consolidate setup of SPIFMTn in one function
spi: davinci: setup chip-select timers values only if timer enabled
spi: davinci: add support for wait enable timeouts
spi: davinci: remove unused members of davinci_spi_slave
spi: davinci: eliminate the single member structure davinci_spi_slave
spi: davinci: eliminate unnecessary update of davinci_spi->count
spi: davinci: simplify calculation of edma acount value
spi: davinci: check for NULL buffer pointer before using it
spi: davinci: remove unnecessary disable of SPI
spi: davinci: remove unnecessary 'count' variable in driver private data
spi: davinci: remove unnecessary completion variable initialization
spi: davinci: remove non-useful interrupt mode support
spi: davinci: simplify poll mode transfers
spi: davinci: add support for interrupt mode
spi: davinci: configure the invariable bits in spipc0 only once
spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
spi: davinci: do not store DMA channel information per chip select
spi: davinci: always start transmit DMA
spi: davinci: do not use temporary buffer if no transmit data provided
spi: davinci: always start receive DMA
spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
spi: davinci: fix DMA event generation stoppage
spi: davinci: fix EDMA CC errors at end of transfers
spi: davinci: handle DMA completion errors correctly
spi: davinci: remove usage of additional completion variables for DMA
spi: davinci: let DMA operation be specified on per-device basis
spi: davinci: remove non-useful "clk_internal" platform data
spi: davinci: enable and power-up SPI only when required
spi: davinci: setup the driver owner
spi: davinci: add additional comments
spi: davinci: add EF Johnson Technologies copyright
spi: davinci: removed unused #defines
spi: davinci: remove unnecessary typecast
spi: davinci: do not treat Tx interrupt being set as error
spi: davinci: do not allocate DMA channels during SPI device setup
spi: davinci: remove unnecessary private data member 'region_size'
spi: davinci: shorten variable names
spi: davinci: kconfig: add manufacturer name to prompt string
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
The EVM hardware for all these variants is the same (except
for the actual SoC populated).
U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the mach-davinci/Kconfig to enable gpio-keys-polled as default when
da850-evm machine is enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: "Nori, Sekhar" <nsekhar@ti.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.
Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.
The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Victor Rodriguez <vm.rod25@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.
The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.
Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Commit fcf173e451 (usb: musb: add names for IRQs
in structure resource) forgot to assign name to the DA8xx MUSB IRQ resource.
Because of that MUSB driver fails to load on DA8xx machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ensure that the at24 eeprom driver is selected for certain boards that
need boot data (e.g. MAC address) from EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There was a single case of 'da850evm' prefix in the board-da850-evm.c file
where the reset of the prefixes were 'da850_evm'; change it to 'da850_evm' for
consistency.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Change the mach-davinci Kconfig file so that GPIO_PCA953X is default when
MACH_DAVINCI_DA850_EVM is set instead of always selecting. This allows users
to compile pca953x as a module.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
CC: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the RMII PHY on the UI board is enabled with CONFIG_DA850_UI_RMII
then then following will be printed to the console when warnings are
also enabled:
WARNING: at drivers/gpio/gpiolib.c:1567 __gpio_set_value+0x4c/0x5c()
Modules linked in:
[<c002c6ac>] (unwind_backtrace+0x0/0xf8) from [<c003b48c>] (warn_slowpath_common+0x4c/0x64)
[<c003b48c>] (warn_slowpath_common+0x4c/0x64) from [<c003b4c0>] (warn_slowpath_null+0x1c/0x24)
[<c003b4c0>] (warn_slowpath_null+0x1c/0x24) from [<c01aed60>] (__gpio_set_value+0x4c/0x5c)
[<c01aed60>] (__gpio_set_value+0x4c/0x5c) from [<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x2
44)
[<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x244) from [<c02e2e1c>] (pca953x_probe+0x1f8/0x29
0)
<snip>
Traced the WARN_ON to the gpio_set_value(rmii_sel,0) call in
da850_evm_setup_emac_rmii. Replacing the call with the _cansleep variant
results in no more warning. Also replacing the gpio_set_value calls in the
teardown function.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
aemif_calc_rate() can return a negative error value, so all the
variables that get tested for this value need to be signed.
The maximum bit width of WSETUP(WSETUP_MAX) appears to be 30 bits
(0xf << 26). Using a signed instead of an unsigned integer
shouldn't make a difference here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A common do-while loop can be factored out from the end of
the branches.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch applies the following modifications to the tnetv107x clock tree:
- reparent tnetv107x usb clocks to usbss
- mark timer1 as always enabled
- enable set_rate on pll divider output clocks
- adjust tnetv107x tsc sysclk rate lower to fix invalid reset defaults
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the sysclk rate setting code to use the divider mask
specified in pll_data. Without this, devices with different divider ranges
(e.g. tnetv107x) fail.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Overwrite the default implementation of sched_clock that is based on
jiffies by something more precise. This improves timestamps in ftrace.
Implementation is copied from OMAP platform code.
Signed-off-by: Andreas Gaeer <Andreas.Gaer@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add comments describing the platform data members
and per-chip-select SPI configuration structure.
Also, add some comments describing the what happens
during the driver probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.
Remove this platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.
A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.
This makes sense since there are dedicated DMA channels meant
for SPI use.
This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.
Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
Some boards that were added after the mass io_pgoffst/io_physio
removal, and were not updated in the original patch. Fixup here.
c.f. original io_pgoffst/io_physio removal
commit 6451d7783b
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most of the regulator data structures are local to the
board file, but not made static. Fix this.
Also make the nand partition table static.
This gets rid of all the sparse warnings for this file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On Davinci SRAM is mapped as MT_DEVICE becasue of the section
mapping pre-requisite instead of intended MT_MEMORY_NONCACHED
Since the section mapping limitation gets fixed with first
patch in this series, the MT_MEMORY_NONCACHED can be used now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds initial support for the Hawkboard-L138 system
It is under the machine name "omapl138_hawkboard".
This system is based on the da850 davinci CPU architecture.
Information on these system may be found at http://www.hawkboard.org.
Basic support for the UART console is included in this patch.
It's tested with latest Angstrom File Systems like ramdisk
from http://alturl.com/imb45.
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For the MityDSP-L138/MityARM-1808 SOMS, read the factory assigned
MAC address from the onboard I2C EPROM and assign it to the emac
device during platform initialization.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's touchscreen
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds evm board specific keymap definitions and controller
configuration data for on-chip keypad controller on tnetv107x silicon.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's keypad
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.
In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds mdio platform devices on SoCs that have the necessary
hardware. Clock lookup entries (aliases) have also been added, so that the
MDIO and EMAC drivers can independently enable/disable a shared underlying
clock. Further, the EMAC MMR region has been split down into separate MDIO
and EMAC regions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the i2c0 bus and attached devices to the MityDSP-L138
and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator
needed for power management and a small 24c02 EPROM that contains
factory configuration data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds an entry into the idcode table for tnetv107x silicon revision
1.1 and 1.2 devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system
on Module (SOM) under the machine name "mityomapl138". These SOMs are based
on the da850 davinci CPU architecture. Information on these SOMs may be
found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is
included in this patch.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds machine checks in the serial console init routines
for the DA8XX EVM boards. This is needed because there are other
DA8XX based machines that use a different UART/tty as the console
and may be included in a common kernel build.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup NAND flash timing on DM6467T EVM.
Without the timing setup, the NAND flash on DM6467T
RevC EVM reports a number of random bad blocks because
of read errors.
Also, with this, copying a 100M file on RevB EVM takes
~35 sec against 1 minute 30 seconds earlier.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup the NAND flash timings for DA850 EVM
Before configuring the timing values, throughput calculation
using dd command yielded 469 kB/s write and 966 kB/s read speed.
After the timing configuration, the throughput was measured to
be 2.4 MB/s write and 5 MB/s read.
[Mukul Bhatnagar: actual calculation of timing values from the
NAND datasheet]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Mukul Bhatnagar <mbhatnagar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup the NAND flash timings for DA830 EVM.
Before configuring the timing values, throughput calculation
using dd command yielded 477 kB/s write and 970 kB/s read speed.
After the timing configuration, the throughput was measured to
be 2.5 MB/s write and 5.1 MB/s read.
[Mukul Bhatnagar: actual calculation of timing values from the
NAND datasheet]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mukul Bhatnagar <mbhatnagar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DM644x EVM nand flash timing was earlier being
done as a special case in the NAND driver itself.
With the NAND driver now capable of progamming the
AEMIF interface using timing data passed from the
platform, the timing values are being moved into
their rightful place in the EVM specific board file.
The values being programmed match what was being done
earlier and thus do not represent any change in
performance/functionality.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the audio driver uses EDMAQ_0 as the DMA queue,
but on DM365 this queue is specially designed for video
transfers with a large fifo size. Having both audio and
video transfers on the same queue leads to noise on the
audio side.
This patch changes the audio queue number for DM365 to
EDMAQ_3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add resources, platform device and convenience registration function for DA850's second MMC/SD controller (MMCSD1).
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Split mmcsd_clk into mmcsd0_clk and mmcsd1_clk and add davinci_mmc.1
in preparation for adding support for MMCSD1 peripheral in DA850.
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add LPSC id for DA850's MMCSD1 peripheral.
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
If irq2ctlr() fails return IRQ_NONE.
Also as it can fail make 'ctlr' signed.
The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)
// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }
@@
identifier r1.f;
type T;
unsigned T x;
@@
*x = f(...)
...
*x > 0
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode
specific pin lists, while what pin group is used is a function of how the board
is wired. Copy the pin lists to board-da850-evm.c, renaming them accordingly,
and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing
the CPGMAC module as a whole...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board
specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c,
renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the
two lists in da850.c into one, representing the EMIF 2.5 module as a whole,
just like we have it in da830.c...
While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as
this function is called from non '__init' code...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is a bugfix for the original tnetv107x submission series. The psc_regs
base array was being discarded post-init, and this was causing a crash during
post-init clock enable/disable.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF
timing to remain valid even as the PLL0 output is changed by cpufreq
driver to save power.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On OMAP-L138 SoC, some of the sysclks need not be at a fixed ratio
to CPU clock and can be kept at a relatively constant rate by
adjusting the PLLDIVn ratio even as cpufreq goes ahead and changes
the CPU clock.
This feature can be used to keep the EMIFA (PLL0 SYSCLK3) clock at a
constant rate so that the EMIF timings need not be re-programmed
whenever the CPU frequency changes.
This patch adds the required suppport to cpufreq driver.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setting sysclk rate will be useful in cases where the
sysclk is not at a fixed ratio to the PLL output but
can asynchronously be changed.
This support forms the basis of attempt to keep the AEMIF
clock constant on OMAP-L138 even as PLL0 output changes
as ARM clock is changed to save power.
This patch has been tested on OMAP-L138.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch disables internal pulldowns for all MMC/SD1
pins. Presently only MMCSD1_CMD pin's pull down is
disabled, but with this some MMC/SD cards do not get
detected on MMC/SD1 slot of the EVM.
The problem was reproducible with SanDisk 4GB SDHC card.
Reported-by: Stephane Bovagne <s-bovagne@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For each DA850 OPP, the normal ('NOM') voltage defined in the tecnical
reference manual (TRM) is actually the minimum voltage the frequency
is supported at.
The minimum ('MIN') voltage defined in TRM is meant to take care of
voltage fluctuations and the device should not be run at this voltage
for extended periods of time.
Fix the OPP definitions to define the cvdd_min as the normal voltage
defined in the datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin
compatible ARM9 microprocessor offering from TI.
The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin
compatible ARM9 microprocessor offering from TI.
More information about these processors available at:
www.ti.com/am1x
Because of their compatibiliy with OMAP-L1x, the kernel
support for OMAP-L1x is fully relevant to AM1x processors.
This patch updates the Kconfig prompt and help text to include
the AM1x part names to help users select configurations required
for these parts easily.
Also, the hardware information that shows up in /proc/cpuinfo
is updated to show applicability of the respective OMAP-L1x EVMs
for AM1x parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In arch/arm/mach-davinci/Kconfig, some of the configuration
items are indented with multiple spaces instead of tabs.
Also, in couple of places, two spaces are used in the middle
of help text where one should do.
This patch fixes both issues.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Manjunath Hadli