Since an early commit a few flags have no longer
been used. Remove these definitions to reduce code clutter.
Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.
Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.
Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor cleanup so that we are always updating pf->flags when we
make a change to the private flags instead of updating a mix of either
pf->flags and/or pf->hw_disabled_flags.
In addition I went through and cleaned out all the spots where we were
using the X722 define in regards to this flag.
Lastly since we changed the logic I went through and flushed out any
redundancy and cleaned up the handling of the flags in the Tx path.
Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Re-word the error message displayed when adding a filter with an
invalid flow type. Additionally, report a distinct error message when
the IPv4 protocol is at fault.
Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.
This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull sparc fixes from David Miller:
"Several fixes here, mostly having to due with either build errors or
memory corruptions depending upon whether you have THP enabled or not"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove unused wp_works_ok macro
sparc32: Export vac_cache_size to fix build error
sparc64: Fix memory corruption when THP is enabled
sparc64: Fix kernel panic due to erroneous #ifdef surrounding pmd_write()
arch/sparc: Avoid DCTI Couples
sparc64: kern_addr_valid regression
sparc64: Add support for 2G hugepages
sparc64: Fix size check in huge_pte_alloc
ARM:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
PPC:
- Check for a NULL return from kzalloc
s390:
- Prevent translation exception errors on valid page tables for the
instruction-exection-protection support
x86:
- Fix Page-Modification Logging when running a nested guest
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJY5/X8AAoJEED/6hsPKofo8hQH/As3CbihZMysaK6JJTx5oMZw
b3W8p8xVXVu4dKM8WnXa6m5xBDFmOa7eBB+CtT3gP68XnFvMpr/vPmDv6v6i9p8q
7VyALDqqk2fxDmgHEwuETw9XZyuhdyCz/GaINCdnAJs25wTFOA7r0WEW5W8qRJpA
9nQirapdJcknymIch1JqeWlYYmbIaFzT8jItfA9QQ7F9mG4pxC8D1k2D56lNYwTf
FJIgXgkMPe7CPDXmgc/KqT5+iVsc/+SgzP/WdH6bX/007TV71sksxxfz6fIrao0X
RtcL2WIZTXBdSNrvXflHhCfYgogPgCnYp8AsYTIa+IEijcfteJx7UiET47Ne0Ow=
=/SPG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
PPC:
- Check for a NULL return from kzalloc
s390:
- Prevent translation exception errors on valid page tables for the
instruction-exection-protection support
x86:
- Fix Page-Modification Logging when running a nested guest"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Check for kmalloc errors in ioctl
KVM: nVMX: initialize PML fields in vmcs02
KVM: nVMX: do not leak PML full vmexit to L1
KVM: arm/arm64: vgic: Fix GICC_PMR uaccess on GICv3 and clarify ABI
KVM: arm64: Ensure LRs are clear when they should be
kvm: arm/arm64: Fix locking for kvm_free_stage2_pgd
KVM: s390: remove change-recording override support
arm/arm64: KVM: Take mmap_sem in kvm_arch_prepare_memory_region
arm/arm64: KVM: Take mmap_sem in stage2_unmap_vm
Pull audit cleanup from Paul Moore:
"A week later than I had hoped, but as promised, here is the audit
uninline-fix we talked about during the last audit pull request.
The patch is slightly different than what we originally discussed as
it made more sense to keep the audit_signal_info() function in
auditsc.c rather than move it and bunch of other related
variables/definitions into audit.c/audit.h.
At some point in the future I need to look at how the audit code is
organized across kernel/audit*, I suspect we could do things a bit
better, but it doesn't seem like a -rc release is a good place for
that ;)
Regardless, this patch passes our tests without problem and looks good
for v4.11"
* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
audit: move audit_signal_info() into kernel/auditsc.c
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: move pcp and lru-pcp draining into single wq
mailmap: update Yakir Yang email address
mm, swap_cgroup: reschedule when neeed in swap_cgroup_swapoff()
dax: fix radix tree insertion race
mm, thp: fix setting of defer+madvise thp defrag mode
ptrace: fix PTRACE_LISTEN race corrupting task->state
vmlinux.lds: add missing VMLINUX_SYMBOL macros
mm/page_alloc.c: fix print order in show_free_areas()
userfaultfd: report actual registered features in fdinfo
mm: fix page_vma_mapped_walk() for ksm pages
We currently have 2 specific WQ_RECLAIM workqueues in the mm code.
vmstat_wq for updating pcp stats and lru_add_drain_wq dedicated to drain
per cpu lru caches. This seems more than necessary because both can run
on a single WQ. Both do not block on locks requiring a memory
allocation nor perform any allocations themselves. We will save one
rescuer thread this way.
On the other hand drain_all_pages() queues work on the system wq which
doesn't have rescuer and so this depend on memory allocation (when all
workers are stuck allocating and new ones cannot be created).
Initially we thought this would be more of a theoretical problem but
Hugh Dickins has reported:
: 4.11-rc has been giving me hangs after hours of swapping load. At
: first they looked like memory leaks ("fork: Cannot allocate memory");
: but for no good reason I happened to do "cat /proc/sys/vm/stat_refresh"
: before looking at /proc/meminfo one time, and the stat_refresh stuck
: in D state, waiting for completion of flush_work like many kworkers.
: kthreadd waiting for completion of flush_work in drain_all_pages().
This worker should be using WQ_RECLAIM as well in order to guarantee a
forward progress. We can reuse the same one as for lru draining and
vmstat.
Link: http://lkml.kernel.org/r/20170307131751.24936-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We got need_resched() warnings in swap_cgroup_swapoff() because
swap_cgroup_ctrl[type].length is particularly large.
Reschedule when needed.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704061315270.80559@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While running generic/340 in my test setup I hit the following race. It
can happen with kernels that support FS DAX PMDs, so v4.10 thru
v4.11-rc5.
Thread 1 Thread 2
-------- --------
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
'entry' is NULL, can't call lock_slot()
spin_unlock_irq()
radix_tree_preload()
dax_iomap_pmd_fault()
grab_mapping_entry()
spin_lock_irq()
get_unlocked_mapping_entry()
...
lock_slot()
spin_unlock_irq()
dax_pmd_insert_mapping()
<inserts a PMD mapping>
spin_lock_irq()
__radix_tree_insert() fails with -EEXIST
<fall back to 4k fault, and die horribly
when inserting a 4k entry where a PMD exists>
The issue is that we have to drop mapping->tree_lock while calling
radix_tree_preload(), but since we didn't have a radix tree entry to
lock (unlike in the pmd_downgrade case) we have no protection against
Thread 2 coming along and inserting a PMD at the same index. For 4k
entries we handled this with a special-case response to -EEXIST coming
from the __radix_tree_insert(), but this doesn't save us for PMDs
because the -EEXIST case can also mean that we collided with a 4k entry
in the radix tree at a different index, but one that is covered by our
PMD range.
So, correctly handle both the 4k and 2M collision cases by explicitly
re-checking the radix tree for an entry at our index once we reacquire
mapping->tree_lock.
This patch has made it through a clean xfstests run with the current
v4.11-rc5 based linux/master, and it also ran generic/340 500 times in a
loop. It used to fail within the first 10 iterations.
Link: http://lkml.kernel.org/r/20170406212944.2866-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: <stable@vger.kernel.org> [4.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting thp defrag mode of "defer+madvise" actually sets "defer" in the
kernel due to the name similarity and the out-of-order way the string is
checked in defrag_store().
Check the string in the correct order so that
TRANSPARENT_HUGEPAGE_DEFRAG_KSWAPD_OR_MADV_FLAG is set appropriately for
"defer+madvise".
Fixes: 21440d7eb9 ("mm, thp: add new defer+madvise defrag option")
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704051814420.137626@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In PT_SEIZED + LISTEN mode STOP/CONT signals cause a wakeup against
__TASK_TRACED. If this races with the ptrace_unfreeze_traced at the end
of a PTRACE_LISTEN, this can wake the task /after/ the check against
__TASK_TRACED, but before the reset of state to TASK_TRACED. This
causes it to instead clobber TASK_WAKING, allowing a subsequent wakeup
against TRACED while the task is still on the rq wake_list, corrupting
it.
Oleg said:
"The kernel can crash or this can lead to other hard-to-debug problems.
In short, "task->state = TASK_TRACED" in ptrace_unfreeze_traced()
assumes that nobody else can wake it up, but PTRACE_LISTEN breaks the
contract. Obviusly it is very wrong to manipulate task->state if this
task is already running, or WAKING, or it sleeps again"
[akpm@linux-foundation.org: coding-style fixes]
Fixes: 9899d11f ("ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL")
Link: http://lkml.kernel.org/r/xm26y3vfhmkp.fsf_-_@bsegall-linux.mtv.corp.google.com
Signed-off-by: Ben Segall <bsegall@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When __{start,end}_ro_after_init is referenced from C code, we run into
the following build errors on blackfin:
kernel/extable.c:169: undefined reference to `__start_ro_after_init'
kernel/extable.c:169: undefined reference to `__end_ro_after_init'
The build error is due to the fact that blackfin is one of the few
arches that prepends an underscore '_' to all symbols defined in C.
Fix this by wrapping __{start,end}_ro_after_init in vmlinux.lds.h with
VMLINUX_SYMBOL(), which adds the necessary prefix for arches that have
HAVE_UNDERSCORE_SYMBOL_PREFIX.
Link: http://lkml.kernel.org/r/1491259387-15869-1-git-send-email-jeyu@redhat.com
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Eddie Kovsky <ewk@edkovsky.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fdinfo for userfault file descriptor reports UFFD_API_FEATURES. Up
until recently, the UFFD_API_FEATURES was defined as 0, therefore
corresponding field in fdinfo always contained zero. Now, with
introduction of several additional features, UFFD_API_FEATURES is not
longer 0 and it seems better to report actual features requested for the
userfaultfd object described by the fdinfo.
First, the applications that were using userfault will still see zero at
the features field in fdinfo. Next, reporting actual features rather
than available features, gives clear indication of what userfault
features are used by an application.
Link: http://lkml.kernel.org/r/1491140181-22121-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doug Smythies reports oops with KSM in this backtrace, I've been seeing
the same:
page_vma_mapped_walk+0xe6/0x5b0
page_referenced_one+0x91/0x1a0
rmap_walk_ksm+0x100/0x190
rmap_walk+0x4f/0x60
page_referenced+0x149/0x170
shrink_active_list+0x1c2/0x430
shrink_node_memcg+0x67a/0x7a0
shrink_node+0xe1/0x320
kswapd+0x34b/0x720
Just as observed in commit 4b0ece6fa0 ("mm: migrate: fix
remove_migration_pte() for ksm pages"), you cannot use page->index
calculations on ksm pages.
page_vma_mapped_walk() is relying on __vma_address(), where a ksm page
can lead it off the end of the page table, and into whatever nonsense is
in the next page, ending as an oops inside check_pte()'s pte_page().
KSM tells page_vma_mapped_walk() exactly where to look for the page, it
does not need any page->index calculation: and that's so also for all
the normal and file and anon pages - just not for THPs and their
subpages. Get out early in most cases: instead of a PageKsm test, move
down the earlier not-THP-page test, as suggested by Kirill.
I'm also slightly worried that this loop can stray into other vmas, so
added a vm_end test to prevent surprises; though I have not imagined
anything worse than a very contrived case, in which a page mlocked in
the next vma might be reclaimed because it is not mlocked in this vma.
Fixes: ace71a19ce ("mm: introduce page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1704031104400.1118@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding support for TSO and checksum hardware offloads for ipv6.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang says:
====================
net-next: dsa: add Mediatek MT7530 support
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N which includes 7-port
Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY. Among these ports,
The port from 0 to 4 are the user ports connecting with the remote devices
while the port 5 and 6 are the CPU ports connecting into Mediatek Ethernet
GMAC.
The patch series integrated Mediatek MT7530 into DSA support which
includes the most of the essential callbacks such as tag insertion for
port distinguishing, port control, bridge offloading, STP setup and
ethtool operations to allow DSA to model each user port into independently
standalone netdevice as the other DSA driver had done.
Changes since v1:
- rebased into 4.11-rc1
- refined binding document including below five items
- changed the type of mediatek,mcm into bool
- used reset controller binding for MCM reset and removed "mediatek,ethsys"
property from binding
- reused CPU port's ethernet Phandle instead of creating new one and removed
"mediatek,ethernet" property from binding
- aligned naming for GPIO reset with dsa/marvell.txt
- added phy-mode as required property child nodes within ports container
- handled gpio reset with devm_gpiod_* API
- refined comment words
- removed condition for CDM setting since the setup looks both fine for all cases
- allowed of_find_net_device_by_node() working with pointing the device node into
real netdev instance
- fixed Kbuild warnings
Changes since v2:
- reuse readx_poll_timeout() to poll
- add proper macro instead of hard coding
- treat inconsistent cpu port as warning
- remove the usage for regmap-debugfs
- show error message when invalid id is found
- put the logic for the setup of trgmii into adjut_link()
- refine and reuse logic between port_[disable,enable], and default port setup
- correct typo
Changes since v3:
- used struct as the parameter for readx_poll_timeout() and kill
extra lpriv defined
- moved around function to get out of an additional declaration
- fixed kbuild errors caused by missing proper include in the latest tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.
For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.
The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the patch adds the setup of the corresponding device node of GMAC into the
netdev instance which could allow other modules such as DSA to find the
instance through the node in dt-bindings using of_find_net_device_by_node()
call.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the setup for allowing CDM can recognize these packets with
carrying port-distinguishing tag. Otherwise, these tagging packets will be
handled incorrectly by CDM. The setup is also working out for general
untag packets as well.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device-tree binding for Mediatek MT7530 switch.
Cc: devicetree@vger.kernel.org
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this fix (and another to the userspace component itself
described later), the kernel will be unable to process any OrangeFS
requests after the userspace component is restarted (due to a crash or
at the administrator's behest).
The bug here is that inside orangefs_remount, the orangefs_request_mutex
is locked. When the userspace component restarts while the filesystem
is mounted, it sends a ORANGEFS_DEV_REMOUNT_ALL ioctl to the device,
which causes the kernel to send it a few requests aimed at synchronizing
the state between the two. While this is happening the
orangefs_request_mutex is locked to prevent any other requests going
through.
This is only half of the bugfix. The other half is in the userspace
component which outright ignores(!) requests made before it considers
the filesystem remounted, which is after the ioctl returns. Of course
the ioctl doesn't return until after the userspace component responds to
the request it ignores. The userspace component has been changed to
allow ORANGEFS_VFS_OP_FEATURES regardless of the mount status.
Mike Marshall says:
"I've tested this patch against the fixed userspace part. This patch is
real important, I hope it can make it into 4.11...
Here's what happens when the userspace daemon is restarted, without
the patch:
=============================================
[ INFO: possible recursive locking detected ]
[ 4.10.0-00007-ge98bdb3 #1 Not tainted ]
---------------------------------------------
pvfs2-client-co/29032 is trying to acquire lock:
(orangefs_request_mutex){+.+.+.}, at: service_operation+0x3c7/0x7b0 [orangefs]
but task is already holding lock:
(orangefs_request_mutex){+.+.+.}, at: dispatch_ioctl_command+0x1bf/0x330 [orangefs]
CPU: 0 PID: 29032 Comm: pvfs2-client-co Not tainted 4.10.0-00007-ge98bdb3 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.fc25 04/01/2014
Call Trace:
__lock_acquire+0x7eb/0x1290
lock_acquire+0xe8/0x1d0
mutex_lock_killable_nested+0x6f/0x6e0
service_operation+0x3c7/0x7b0 [orangefs]
orangefs_remount+0xea/0x150 [orangefs]
dispatch_ioctl_command+0x227/0x330 [orangefs]
orangefs_devreq_ioctl+0x29/0x70 [orangefs]
do_vfs_ioctl+0xa3/0x6e0
SyS_ioctl+0x79/0x90"
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Acked-by: Mike Marshall <hubcap@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent extension of F-RTO 89fe18e44 ("tcp: extend F-RTO
to catch more spurious timeouts") interacts badly with certain
broken middle-boxes. These broken boxes modify and falsely raise
the receive window on the ACKs. During a timeout induced recovery,
F-RTO would send new data packets to probe if the timeout is false
or not. Since the receive window is falsely raised, the receiver
would silently drop these F-RTO packets. The recovery would take N
(exponentially backoff) timeouts to repair N packet losses. A TCP
performance killer.
Due to this unfortunate situation, this patch removes this extension
to revert F-RTO back to the RFC specification.
Fixes: 89fe18e44f ("tcp: extend F-RTO to catch more spurious timeouts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve scalability, if hardware queues are shared, restart
a single hardware queue in round-robin fashion. Rename
blk_mq_sched_restart_queues() to reflect the new semantics.
Remove blk_mq_sched_mark_restart_queue() because this function
has no callers. Remove flag QUEUE_FLAG_RESTART because this
patch removes the code that uses this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
While running the srp-test software I noticed that request
processing stalls sporadically at the beginning of a test, namely
when mkfs is run against a dm-mpath device. Every time when that
happened the following command was sufficient to resume request
processing:
echo run >/sys/kernel/debug/block/dm-0/state
This patch avoids that such request processing stalls occur. The
test I ran is as follows:
while srp-test/run_tests -d -r 30 -t 02-mq; do :; done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Jens Axboe <axboe@fb.com>
If a .queue_rq() function returns BLK_MQ_RQ_QUEUE_BUSY then the block
driver that implements that function is responsible for rerunning the
hardware queue once requests can be queued again successfully.
commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped
queues") removed the blk_mq_stop_hw_queue() call from scsi_queue_rq()
for the BLK_MQ_RQ_QUEUE_BUSY case. Hence change all calls to functions
that are intended to rerun a busy queue such that these examine all
hardware queues instead of only stopped queues.
Since no other functions than scsi_internal_device_block() and
scsi_internal_device_unblock() should ever stop or restart a SCSI
queue, change the blk_mq_delay_queue() call into a
blk_mq_delay_run_hw_queue() call.
Fixes: commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped queues")
Fixes: commit 7e79dadce2 ("blk-mq: stop hardware queue in blk_mq_delay_queue()")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Introduce a function that runs a hardware queue unconditionally
after a delay. Note: there is already a function that stops and
restarts a hardware queue after a delay, namely blk_mq_delay_queue().
This function will be used in the next patch in this series.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
- A stable@ fix for raid target's raid1 support (when no bitmap is used)
- A 4.11 cache metadata v2 format fix to properly test blocks are clean
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY56smAAoJEMUj8QotnQNa3xYH/39l25eGzam0cnITa31cX9uu
lb+oWnqbgvbd65HZr2QPu9RO8LQMK9wxw40wapyYTEnkDfgeW+hmwYo3BUZ0IpdT
Ry39KGCGaxk3L3cATSgtZT18AsWRHmKqlHLf6y98RdeFLVb3lyUFllkLF9r3M2ep
1Ga2MiMJYffaiTsSKxwZQG3XG7mq9MNfRnCehGAQwjGgWL3EsYHNsq+Hosn/tdtZ
2D7BvAMr2X+3xEUVevqL2dFmJ1D2tbJjtedeAKVOccErV/BofwWPUvTOFX8202+Y
CUC9pW+hDQqpCm15Pr4N6oU4TeC4mHMwGK0SLWmoXkl3VDPbUUO3qC5AwKxsepA=
=cWkE
-----END PGP SIGNATURE-----
Merge tag 'dm-4.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for the verity target's FEC support
- a stable fix for raid target's raid1 support (when no bitmap is used)
- a 4.11 cache metadata v2 format fix to properly test blocks are clean
* tag 'dm-4.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix bufio leaks
dm raid: fix NULL pointer dereference for raid1 without bitmap
dm cache metadata: fix metadata2 format's blocks_are_clean_separate_dirty
dm verity fec: limit error correction recursion
- Restore previous SIGBUS behaviour for unhandled unaligned user accesses
- Revert broken support for the contiguous bit in hugetlb (again...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJY53foAAoJELescNyEwWM0ILEH/An3v6VSnbABDRxvXWkrTvKZ
y4KoHVgSDqehrH8MysrrI7SlB5J5AEGjQI2SzI2InVS4j4Dd/kfqZMeZlo2Z2Idv
KlC4FXb6QhRjJrrLCVIWCZxQL8gqP9KEI+DwB76a46WSYHHWP4ihtfYTxpTSAZbj
mDHOmZ2udc/GjEpPzzPNOhXs0+1dEAHkQa+gW8T5HotQK+VVBwFTJKPXGNjm/YQa
A1lLzYW/R9xRzAeEaJIGa6/jy6jJQ09vkXUdriibRi9qu7+A/xecgq3nb6puwT3j
0BQqvVQ3eAEejlXA5L4xtdwNb3fhe8hK4pq9OgNnhSytntAtbSiqvGTHea03XKY=
=d5YQ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"We've got a regression fix for the signal raised when userspace makes
an unsupported unaligned access and a revert of the contiguous
(hugepte) support for hugetlb, which has once again been found to be
broken. One day, maybe, we'll get it right.
Summary:
- restore previous SIGBUS behaviour for unhandled unaligned user
accesses
- revert broken support for the contiguous bit in hugetlb (again...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "Revert "arm64: hugetlb: partial revert of 66b3923a1a0f""
arm64: mm: unaligned access by user-land should be received as SIGBUS
These patches fix a bunch of longstanding (some over a decade old) metag
user copy fault handling bugs. Thanks go to Al Viro for spotting some of
the questionable code in the first place.
-----BEGIN PGP SIGNATURE-----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=MwhE
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag usercopy fixes from James Hogan:
"Metag usercopy fault handling fixes
These patches fix a bunch of longstanding (some over a decade old)
metag user copy fault handling bugs. Thanks go to Al Viro for spotting
some of the questionable code in the first place"
* tag 'metag-for-v4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag/usercopy: Add missing fixups
metag/usercopy: Fix src fixup in from user rapf loops
metag/usercopy: Set flags before ADDZ
metag/usercopy: Zero rest of buffer from copy_from_user
metag/usercopy: Add early abort to copy_to_user
metag/usercopy: Fix alignment error checking
metag/usercopy: Drop unused macros
- Refine the check for the existence of _HID in find_child_checks()
so that it doesn't trigger for device objects with device IDs
made up by the kernel (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=04+L
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This fixes a core device enumeration code change made in 4.10, in
order to address a reported issue, that went too far.
Specifics:
- Refine the check for the existence of _HID in find_child_checks()
so that it doesn't trigger for device objects with device IDs made
up by the kernel (Rafael Wysocki)"
* tag 'acpi-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Prefer devices without _HID for _ADR matching
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJY5ysAAAoJELDendYovxMvEIoH/2Jl9vM9DzfdTxfyvSS0+i3/
e3UTL4igNSBT5W4t3DL0o5IZ9e6LQ17j8VWqbpT8d6AzdvtW6xx4ZpulPuh/qTnA
pHNUy9yPXr91k4KzSgV3ASaqxdBOIAq74t0u+BwpDjWV8Vok5oONxPf03vigfrKb
jFLZfP0DilSI6YIsExtUqZhT1ydnG6mm0PMXGT5VfHgnotUVapSnZw8Ht/STXRbH
SZ5a1QLcQxfFziFEmBGSOqIKLmA3TYpzBcbSVg4vjysdmf910C8tU6KFkdDhg8Gu
3vWsjBpgxoAmdHYfElD3PDp1pyWTmKkF0jtJavcaNp0GOGD8f5jg1Rf/eozD9CA=
=6Oc6
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.11b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from Juergen Gross:
"A fix for error path cleanup in the xenbus handler"
* tag 'for-linus-4.11b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: remove transaction holder from list before freeing
I saw some very confusing sysctl output on my system:
# cat /proc/sys/net/core/xfrm_aevent_rseqth
-2
# cat /proc/sys/net/core/xfrm_aevent_etime
-10
# cat /proc/sys/net/ipv4/tcp_notsent_lowat
-4294967295
Because we forget to set the *negp flag in proc_douintvec, so it will
become a garbage value.
Since the value related to proc_douintvec is always an unsigned integer,
so we can set *negp to false explictily to fix this issue.
Fixes: e7d316a02f ("sysctl: handle error writing UINT_MAX to u32 fields")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e7d316a02f ("sysctl: handle error writing UINT_MAX to u32
fields") introduced the proc_douintvec helper function, but it forgot to
add the related sanity check when doing register_sysctl_table. So add
it now.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
since 4.10 perf annotate exits on s390 with an "unknown error -95".
Turns out that commit 786c1b5184 ("perf annotate: Start supporting
cross arch annotation") added a hard requirement for architecture
support when objdump is used but only provided x86 and arm support.
Meanwhile power was added so lets add s390 as well.
While at it make sure to implement the branch and jump types.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Andreas Krebbel <krebbel@linux.vnet.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: stable@kernel.org # v4.10+
Fixes: 786c1b5184 "perf annotate: Start supporting cross arch annotation"
Link: http://lkml.kernel.org/r/1491465112-45819-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Connecting to the backend isn't working reliably in xen-fbfront: in
case XenbusStateInitWait of the backend has been missed the backend
transition to XenbusStateConnected will trigger the connected state
only without doing the actions required when the backend has
connected.
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
SSD1306 needs VBAT when it is wired in charge pump configuration only.
Other controllers of the SSD1307 family do not need it at all. This was
introduced by commit ba14301e03 ("fbdev/ssd1307fb: add support to
enable VBAT").
Without VBAT configuration the driver now fails with:
failed to get VBAT regulator: -19
This is caused by misinterpretation of devm_regulator_get_optional
which "returns a struct regulator corresponding to the regulator
producer or IS_ERR() condition".
Handle -ENODEV without bailing out and making VBAT support really
optional.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
[b.zolnierkie: minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
blk_mq_update_nr_hw_queues() used to remap hardware queues, which is the
behavior that drivers expect. However, commit 4e68a01142 changed
blk_mq_queue_reinit() to not remap queues for the case of CPU
hotplugging, inadvertently making blk_mq_update_nr_hw_queues() not remap
queues as well. This breaks, for example, NBD's multi-connection mode,
leaving the added hardware queues unused. Fix it by making
blk_mq_update_nr_hw_queues() explicitly remap the queues.
Fixes: 4e68a01142 ("blk-mq: don't redistribute hardware queues on a CPU hotplug event")
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a new hardware queue is added at runtime, we don't allocate scheduler
tags for it, leading to a crash. This hooks up the scheduler framework
to blk_mq_{init,exit}_hctx() to make sure everything gets properly
initialized/freed.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Jacob Keller