The driver currently creates empty ACL groups, binds them to the
requested port and then fills them with actual ACLs that point to TCAM
regions.
However, empty ACL groups are considered invalid and upcoming firmware
versions are going to forbid their binding.
Work around this limitation by only performing the binding after the
first ACL was added to the group.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set some of the fields within 'mbox_config_profile',
since they are reserved and capability mask should be set to zero.
Signed-off-by: Tal Bar <talb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the opcodes don't use in, out or both mboxes. In such cases, the
mbox address is a reserved field and FW expects it to be zero.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cppcheck report:
[drivers/net/ethernet/cortina/gemini.c:543]: (error) Memory leak: skb_tab
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes: 6eacf31139 ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver calls ida_pre_get() in a loop for no readily apparent
reason. The driver uses ida_simple_get() which will call ida_pre_get()
by itself and there's no need to use ida_pre_get() unless using
ida_get_new().
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the polling mechanism of GLGEN_RSTAT.DEVSTATE in the
PF Reset path when Global Reset is in progress. While the driver
is polling for the end of the PF Reset and the Global Reset is
triggered, abandon the PF Reset path and prepare for the
upcoming Global Reset.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These flags were defined, but there is no use within the driver code, so
we don't need to keep them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting link settings on backplane devices shouldn't be allowed.
This patch adds one more device id to the list which we check
that against.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix return types from i40e_status to enum i40e_status_code.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent patch updated the signature for i40e_aq_set_switch_config() to
add a new parameter 'mode'. It forgot to document the parameter in the
doxygen function header comment. Add the parameter to the function
description now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During suspend client MSIx vectors are freed while they are still
in use causing a crash on entering S3.
Fix this calling client close before freeing up its MSIx vectors.
Also update the client MSIx vectors on resume before client
open is called.
Fixes commit b980c0634f ("i40e: shutdown all IRQs and disable MSI-X
when suspended")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting link settings on backplane devices shouldn't be allowed.
This patch adds one more device id to the list which we check
that against.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_set_link_ksettings and i40e_get_link_ksettings use different
codepaths to check available and supported advertisement modes. This
creates scenarios where it's possible to set a mode that's not allowed,
resulting in a link down.
Fix setting advertisement in i40e_set_link_ksettings by calling
i40e_get_link_ksettings to check what modes are allowed.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing some code review I noticed that we can get into a state where
we exit with the "IN_CRITICAL_TASK" bit set while notifying the PF of
flower filters. This patch is meant to address that plus tweak the ordering
of the while loop waiting on it slightly so that we don't wait an extra
period after we have failed for the last time.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, remove the TSO-specific fields in the TX pool
strcutures. These are no longer needed with the introduction
of separate buffer pools for TSO transmissions.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update routine that cleans up any outstanding transmits that
have not received completions when the device needs to close.
Introduces a helper function that cleans one TX pool to make
code more readable.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve TX pool buffer accounting to prevent the producer
index from overruning the consumer. First, set the next free
index to an invalid value if it is in use. If next buffer
to be consumed is in use, drop the packet.
Finally, if the transmit fails for some other reason, roll
back the consumer index and set the free map entry to its original
value. This should also be done if the DMA map fails.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update TX and TX completion routines to account for TX pool
restructuring. TX routine first chooses the pool depending
on whether a packet is GSO or not, then uses it accordingly.
For the completion routine to know which pool it needs to use,
set the most significant bit of the correlator index to one
if the packet uses the TSO pool. On completion, unset the bit
and use the correlator index to release the buffer pool entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function that initializes one TX pool. Use that to
create each pool entry in both the standard TX pool and TSO
pool arrays.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function that frees one TX pool. Use that to release
each pool in both the standard TX pool and TSO pool arrays.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update TX pool reset routine to accommodate new TSO pool array. Introduce
a function that resets one TX pool, and use that function to initialize
each pool in both pool arrays.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some unused fields in the structure and include values
describing the individual buffer size and number of buffers in
a TX pool. This allows us to use these fields for TX pool buffer
accounting as opposed to using hard coded values. Include a new
pool array for TSO transmissions.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155
Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver implementation returns support for private flags, while
no private flags are present. When asked for the number of private
flags it returns the number of statistic flag names.
Fix this by returning EOPNOTSUPP for not implemented ethtool flags.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9ffcc3725f ("mlxsw: spectrum: Allow packets to be trapped
from any PG") I fixed a problem where packets could not be trapped to
the CPU due to exceeded shared buffer quotas. The mentioned commit
explains the problem in detail.
The problem was fixed by assigning a minimum quota for the CPU port and
the traffic class used for scheduling traffic to the CPU.
However, commit 117b0dad2d ("mlxsw: Create a different trap group list
for each device") assigned different traffic classes to different
packet types and rendered the fix useless.
Fix the problem by assigning a minimum quota for the CPU port and all
the traffic classes that are currently in use.
Fixes: 117b0dad2d ("mlxsw: Create a different trap group list for each device")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Eddie Shklaer <eddies@mellanox.com>
Tested-by: Eddie Shklaer <eddies@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting sge_uld_rxq_info to NULL in free_queues_uld().
We are referencing sge_uld_rxq_info in cxgb_up(). This
will fix a panic when interface is brought up after a
ULDq creation failure.
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD)
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudhar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Moved interrupt enable related code from octeon_process_droq_poll_cmd()
to separate function octeon_enable_irq().
2) Removed wrapper function octeon_process_droq_poll_cmd(), and directlyi
using octeon_droq_process_poll_pkts().
3) Removed unused macros POLL_EVENT_XXX.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
notify uld drivers if the adapter encounters fatal
error.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link updates were not reported to qedr correctly.
Leading to cases where a link could be down, but qedr
would see it as up.
In addition, once qede was loaded, link state would be up,
regardless of the actual link state.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets
Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in the MPA unalign flow where a FPDU header is
split over two tcp segments. The length of the first fragment in this
case was not initialized properly and should be '1'
Fixes: c7d1d839 ("qed: Add support for MPA header being split over two tcp packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)
The devicetree snippet would look something like this:
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
The work done to add the phy_node in the first place (dacdbb4dfc1a1:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.
This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
added vxlan offload support for IPv6 pkts. Required change in
enic_udp_tunnel_del was not made. This creates a bug where once user
adds IPv6 tunnel, hw offload for that cannot be deleted.
This patch removes check for IP proto in tunnel delete path. Driver need
not check for IP proto since same UDP port cannot be used to create two
tunnels.
Fixes: d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we re-enable ATR we need to restore the input set for TCPv4
filters, in order for ATR to function correctly. We already do this for
the normal case of re-enabling ATR when disabling ntuple support.
However, when re-enabling ATR after the last TCPv4 filter is removed (but
when ntuple support is still active), we did not restore the TCPv4
filter input set.
This can cause problems if the TCPv4 filters from FDir had changed the
input set, as ATR will no longer behave as expected.
When clearing the ATR auto-disable flag, make sure we restore the TCPv4
input set to avoid this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch overwrites number of ports for X722 devices with support
for OCP PHY mezzanine.
The old method with checking if port is disabled in the PRTGEN_CNF
register cannot be used in this case. When the OCP is removed, ports
were seen as disabled, which resulted in wrong calculation of partition
id, that caused WoL to be disabled on certain ports.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch needs to expand on the logic for re-enabling ATR. Doing
so would cause some code to break the 80-character line limit.
To reduce the level of indentation, factor out helper functions for
re-enabling ATR and SB rules.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When hardware has trouble with a particular filter, we delete it from
the list. Unfortunately, we did not properly update the per-filter
statistic when doing so.
Create a helper function to handle this, and properly reduce the
necessary counter so that it tracks the number of active filters
properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VF requests adding of MAC filters the checking is done against number
of already present MAC filters not adding them at the same time. It makes
it possible to add a bunch of filters at once possibly exceeding
acceptable limit of I40E_VC_MAX_MAC_ADDR_PER_VF filters.
This happens because when checking vf->num_mac, we do not check how many
filters are being requested at once. Modify the check function to ensure
that it knows how many filters are being requested. This allows the
check to ensure that the total number of filters in a single request
does not cause us to go over the limit.
Additionally, move the check to within the lock to ensure that the
vf->num_mac is checked while holding the lock to maintain consistency.
We could have simply moved the call to i40e_vf_check_permission to
within the loop, but this could cause a request to be non-atomic, and
add some but not all the addresses, while reporting an error code. We
want to avoid this behavior so that users are not confused about which
filters have or have not been added.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We used to use the function i40e_vlan_rx_register as a way to hook
into the now defunct .ndo_vlan_rx_register netdev hook. This was
removed but we kept the function around because we still used it
internally to control enabling or disabling of VLAN stripping.
As pointed out in upstream review, VLAN stripping is only used in a
single location and the previous function is quite small, just inline
it into i40e_restore_vlan() rather than carrying the function
separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix for "Resource temporarily unavailable" problem when virsh is
trying to attach a device to VM. When the VF driver is loaded on
host and virsh is trying to attach it to the VM and set a MAC
address, it ends with a race condition between i40e_reset_vf and
i40e_ndo_set_vf_mac functions. The bug is fixed by adding polling
in i40e_ndo_set_vf_mac function For when the VF is in Reset mode.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seems this is a copy-paste error and that the proper variable to use
in this particular case is _src_ instead of _dst_.
Addresses-Coverity-ID: 1465282 ("Copy-paste error")
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fcoe support was removed via commit 9eed69a914 ("i40e: Drop FCoE code from core driver files")
But this left files in place but un-compilable.
Let's finish the cleaning.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NETIF_F_GSO_SOFTWARE implies support for GSO on SCTP, but the
sunvnet driver does not support GSO for sctp. Here we remove the
NETIF_F_GSO_SOFTWARE feature flag and only report NETIF_F_ALL_TSO
instead.
Signed-off-by: Cathy Zhou <Cathy.Zhou@Oracle.COM>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was introduced in commit
506b0a395f ("[netdrv] tg3: APE heartbeat changes"). The bug occurs
because tp->lock spinlock is held which is obtained in tg3_start
by way of tg3_full_lock(), line 11571. The documentation for usleep_range()
specifically states it cannot be used inside a spinlock.
Fixes: 506b0a395f ("[netdrv] tg3: APE heartbeat changes")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool changes to show port type as TP (Twisted Pair) for
10GBASE-T ports. Same driver and firmware works for liquidio NIC with
SFP+ ports or TP ports.
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_errors counter is incremented by the dpaa_xmit caller.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fd_format has already been initialized at this point.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent changes that make the driver probing compatible with DSA
were not propagated in the dpa_remove() function, breaking the
module unload function. Using the proper device to address the issue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as 'auto' and the forced 'off', 'rs' and 'baser' states, we also
handle combinations of settings (since the fecparam->fec field is a
bitmask), where auto|rs and auto|baser specify a preferred FEC mode but
will fall back to the other if the cable or link partner doesn't support
it. rs|baser (with or without auto bit) means prefer FEC even where
auto wouldn't use it, but let FW choose which encoding to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The case in which we handle a reset from the state where the device is
closed seems to be bugged for all types of reset. For most types of reset
we currently exit the reset routine correctly, but don't set the state to
indicate that we are back in the "closed" state. For some specific cases,
we don't exit the reset routine at all and resetting will cause a closed
device to be opened.
This patch fixes the problem by unconditionally checking the reset_state
and correctly setting the adapter state before returning.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HMA(Host Memory Access) maps a part of host memory for T6-SO memfree cards.
This commit does the following:
- Query FW to check if we have HMA support. If yes, the params will
return HMA size configured in FW. We will dma map memory based
on this size.
- Also contains changes to get HMA memory information via debugfs.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Michael Werner <werner@chelsio.com>
Signed-off-by: Ganesh GR <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're dereferencing "p_hwfn->p_rdma_info" but that is freed on the line
before in qed_rdma_resc_free(p_hwfn).
Fixes: 9de506a547 ("qed: Free RoCE ILT Memory on rmmod qedr")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry, one of the patches I sent in an earlier series
has some dumb mistakes. One was that I had changed the
parameter for the errata workaround function but forgot
to make that change in the code that called it.
The second mistake was a forgotten return value at the end
of the function in case the workaround was not needed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO packets with one segment or with an MSS less than 224 can
cause errors on some backing devices, so disable GSO in those cases.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some backing devices cannot handle small packets well,
so pad any small packets to avoid that. It was recommended
that the VNIC driver should not send packets smaller than the
minimum MTU value provided by firmware, so pad small packets
to be at least that long.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra four bytes of a VLAN packet was throwing off
TX buffer entry values used by the driver. Account for those
bytes when in buffer size and buffer entry calculations
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VLAN tag is present in the Ethernet header, account
for that when providing the L2 header to firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-03-12
This series contains updates to ixgbe and ixgbevf only.
Shannon Nelson provides three fixes to the ipsec portion of ixgbe. Make
sure we are using 128-bit authentication, since it is the only size
supported for hardware offload. Fixed the transmit trailer length
calculation for ipsec by finding the padding value and adding it to the
authentication length, then save it off so that we can put it in the
transmit descriptor to tell the device where to stop the checksum
calculation. Lastly, cleaned up useless and dead code.
Tonghao Zhang adds a ethtool stat for receive length errors, since the
driver was already collecting this counter.
Arnd Bergmann fixed a warning about an used variable by "rephrasing" the
code so that the compiler can see the use of the variable in question.
Paul fixes an issue where "HIDE_VLAN" was being cleared on VF reset, so
ensure to set "HIDE_VLAN" when port VLAN is enabled after a VF reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If port VLAN is enabled, set PFQDE.HIDE_VLAN during VF reset.
Setting only PFQDE.PFQDE during VF reset was clearing PFQDE.HIDE_VLAN.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-03-12
This series contains fixes to e1000e only.
Benjamin Poirier provides two fixes, first reverts commits that changed
what happens to the link status when there is an error. These commits
were to resolve a race condition, but in the process of fixing the race
condition, they changed the behavior when an error occurred. Second fix
resolves a race condition by not setting "get_link_status" to false
after checking the link.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex reported the following race condition:
/* link goes up... interrupt... schedule watchdog */
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
\ e1000e_phy_has_link_generic(..., &link)
link = true
/* link goes down... interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true
/* link is up */
mac->get_link_status = false
link_active = true
/* link_active is true, wrongly, and stays so because
* get_link_status is false */
Avoid this problem by making sure that we don't set get_link_status = false
after having checked the link.
It seems this problem has been present since the introduction of e1000e.
Link: https://lkml.org/lkml/2018/1/29/338
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 19110cfbb3.
This reverts commit 4110e02eb4.
This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98.
Commit 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.
Revert commit 19110cfbb3 ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb3 is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.
Link: https://lkml.org/lkml/2018/3/1/789
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new ixgbevf_set_rx_buffer_len() function causes a harmless warnings
in configurations with large page size:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function 'ixgbevf_set_rx_buffer_len':
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1758:15: error: unused variable 'max_frame' [-Werror=unused-variable]
This rephrases the code so that the compiler can see the use of that
variable, making it slightly easier to read in the process.
Fixes: f15c5ba5b6 ("ixgbevf: add support for using order 1 pages to receive large frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe enabled rlec counter and the rx_error used it.
We can export the counter directly via ethtool -S ethX.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With commit 7f05b467a7 ("xfrm: check for xdo_dev_state_free")
we no longer need to add an empty callback function
to the driver, so now let's remove the useless code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up the Tx trailer length calculation. We can't believe the
trailer len from the xstate information because it was calculated
before the packet was put together and padding added. This bit
of code finds the padding value in the trailer, adds it to the
authentication length, and saves it so later we can put it into
the Tx descriptor to tell the device where to stop the checksum
calculation.
Fixes: 5925947047 ("ixgbe: process the Tx ipsec offload")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Security Association is using
a 128-bit authentication, since that's the only
size that the hardware offload supports.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:371:5: warning:
symbol 'mlxsw_sp_kvdl_single_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:384:5: warning:
symbol 'mlxsw_sp_kvdl_chunks_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:397:5: warning:
symbol 'mlxsw_sp_kvdl_large_chunks_occ_get' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions lan743x_csr_read and lan743x_csr_read are local to the source
and do not need to be in global scope, so make them static.
Cleans up sparse warning:
drivers/net/ethernet/microchip/lan743x_main.c:56:5: warning: symbol
lan743x_csr_read' was not declared. Should it be static?
drivers/net/ethernet/microchip/lan743x_main.c:61:6: warning: symbol
'lan743x_csr_write' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function lan743x_phy_init assigns pointer 'netdev' but this is never read
and hence it can be removed. The return error code handling can also be
cleaned up to remove the variable 'ret'.
Function lan743x_phy_link_status_change assigns pointer 'phy' twice and
this is never read, so it also can be removed.
Finally, function lan743x_tx_napi_poll initializes pointer 'adapter'
and then re-assigns the same value into this pointer a little later on
so this second assignment is redundant and can be also removed.
Cleans up clang warnings:
drivers/net/ethernet/microchip/lan743x_main.c:951:2: warning: Value
stored to 'netdev' is never read
drivers/net/ethernet/microchip/lan743x_main.c:971:3: warning: Value
stored to 'phy' is never read
drivers/net/ethernet/microchip/lan743x_main.c:1583:26: warning: Value
stored to 'adapter' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_spectrum supports offloading of a tc action mirred egress mirror
to a gretap or an ip6gretap netdevice, which necessitates calls to
functions defined in ip_gre, ip6_gre and ip6_tunnel modules. Previously
this was enabled by introducing a hard dependency of MLXSW_SPECTRUM on
NET_IPGRE and IPV6_GRE. However the rest of mlxsw is careful about
picking which modules are absolutely required, and therefore the better
approach is to make mlxsw_spectrum tolerant of absence of one or both of
the GRE flavors.
Hence rework the NET_IPGRE and IPV6_GRE dependencies to just guard
matching modularity, and hide the corresponding code in spectrum_span.c
in an #if IS_ENABLED. Mark mlxsw_sp_span_entry_tunnel_parms_common as
maybe unused, to muffle warnings if neither GRE flavor is selected,
which seems cleaner than introducing a composite #if.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function next to the rest of gretap4 functions. Thus the
generic functions shared between gretap4 and gretap6 are in one block at
the beginning, followed by a gretap4 block, followed by a gretap6 block.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to abstract away access to the
ipv6.sysctl.multipath_hash_policy variable, which is not available on
systems compiled without IPv6 support, introduce a wrapper function
ip6_multipath_hash_policy() that falls back to 0 on non-IPv6 systems.
Use this wrapper from mlxsw/spectrum_router instead of a direct
reference.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check firmware capabilities before setting ethtool
link mode mask, also add few missing speeds.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
50Gbps is a supported speed, Stop reporting it as
unsupported speed.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a scenario where the command queued to firmware get dropped or times
out, MTU change from host will not propagate to firmware. So, it is
required for host driver to wait for response from firmware or timeout
and then return correct status to caller of ndo_change_mtu.
Also moved the common code for MTU change from PF and VF driver files to
common file lio_core.c
Signed-off-by: Veerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID. This may cause a
warning in firmware logs.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_restore_pf_fw_resources routine frees PF resources by calling
close_nic and allocates the resources back, by doing open_nic. However,
this is not needed, if the PF is already in closed state.
This bug causes the driver to call open the device and call request_irq()
when it is not needed. Ultimately, pci_disable_msix() will crash
when bnxt_en is unloaded.
This patch fixes the problem by skipping __bnxt_close_nic and
__bnxt_open_nic inside bnxt_restore_pf_fw_resources routine, if the
interface is not running.
Fixes: 80fcaf46c0 ("bnxt_en: Restore MSIX after disabling SRIOV.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, internal error value is returned by the driver, when
hwrm_cfa_flow_alloc() fails due lack of resources. We should be returning
Linux errno value -ENOSPC instead.
This patch also converts other similar command errors to standard Linux errno
code (-EIO) in bnxt_tc.c
Fixes: db1d36a273 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes added the bnxt_init_int_mode() call in the driver's open
path whenever ring reservations are changed. This call was previously
only called in the probe path. In the open path, if MQPRIO TC has been
setup, the bnxt_init_int_mode() call would reset and mess up the MQPRIO
per TC rings.
Fix it by not re-initilizing bp->tx_nr_rings_per_tc in
bnxt_init_int_mode(). Instead, initialize it in the probe path only
after the bnxt_init_int_mode() call.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag(). The current code is only
passing the 12-bit tag and it is missing the priority bits.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions when the driver fails to add a flow in HW and returns
an error back to the stack, the stack continues to invoke get_flow_stats()
and/or del_flow() on it. The driver fails these APIs with an error message
"no flow_node for cookie". The message gets logged repeatedly as long as
the stack keeps invoking these functions.
Fix this by removing the corresponding netdev_info() calls from these
functions.
Fixes: d7bc730530 ("bnxt_en: add code to query TC flower offload stats")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of vnics to check must be determined ahead of time because
only standard RX rings require vnics to support RFS. The logic is
similar to the ring reservation logic and we can now use the
refactored common functions to do most of the work in setting up
the firmware message.
Fixes: 8f23d638b3 ("bnxt_en: Expand bnxt_check_rings() to check all resources.")
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnxt_hwrm_reserve_{pf|vf}_rings() functions are very similar to
the bnxt_hwrm_check_{pf|vf}_rings() functions. Refactor the former
so that the latter can make use of common code in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF changes unicast mac address by sending mailbox msg to PF, then PF
completes the mac address modification. It may fail when the target
uc mac address is already in the mac_vlan table. VF should be aware
of it by reading the message result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not allowed to add two same unicast mac address entries to the
mac_vlan table. When modify the uc mac address of a VF device to the
same value with the PF device's, the PF device will lose its entry of
the mac_vlan table.
Lookup the mac address in the mac_vlan table, and add it if the entry
is inexistent.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code -EIO was used to indicate mutilple errors in function
hclge_get_mac_vlan_cmd_status().This patch fixes it by using
error code depending on the error type.
For no space error, return -ENOSPC.
For entry not found, return -ENOENT.
For command send fail, return -EIO.
For invalid op code, return -EINVAL.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An enum type variable was used to store an "int" type return value.
This patch fixes it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan ctag filter is enabled, the loopback selftest fails because
loopback selftest does not support vlan.
This patch fixes it by disabling the vlan ctag filter when runnig
loopback selftest.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for querying pfc puase packets statistic
in hclge_ieee_getpfc, which is used to tell user how many pfc
puase packets have been sent and received by this mac port.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original skb->truesize reports the received packet size,
not the actual buffer size NIC driver allocated(1 Page).
The linux net protocol will misjudge the true size of rx queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the firmware cmd to setup mac pause params is the same as the
firmware cmd to pfc pause params, this patch unifies the pause params
setup function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Various driver bug fixes in mlx5, mlx4, bnxt_re and qedr, ranging
from bugs under load to bad error case handling
- There in one largish patch fixing the locking in bnxt_re to avoid
a machine hard lock situation
- A few core bugs on error paths
- A patch to reduce stack usage in the new CQ API
- One mlx5 regression introduced in this merge window
- There were new syzkaller scripts written for the RDMA subsystem
and we are fixing issues found by the bot
- One of the commits (aa0de36a40 “RDMA/mlx5: Fix integer overflow
while resizing CQ”) is missing part of the commit log message and
one of the SOB lines. The original patch was from Leon Romanovsky,
and a cut-n-paste separator in the commit message confused patchworks
which then put the end of message separator in the wrong place in
the downloaded patch, and I didn’t notice in time. The patch made
it into the official branch, and the only way to fix it in-place
was to rebase. Given the pain that a rebase causes, and the fact
that the patch has relevant tags for stable and syzkaller, a revert
of the munged patch and a reapplication of the original patch with
the log message intact was done.
-----BEGIN PGP SIGNATURE-----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=ZvN0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
- Various driver bug fixes in mlx5, mlx4, bnxt_re and qedr, ranging
from bugs under load to bad error case handling
- There in one largish patch fixing the locking in bnxt_re to avoid a
machine hard lock situation
- A few core bugs on error paths
- A patch to reduce stack usage in the new CQ API
- One mlx5 regression introduced in this merge window
- There were new syzkaller scripts written for the RDMA subsystem and
we are fixing issues found by the bot
- One of the commits (aa0de36a40 “RDMA/mlx5: Fix integer overflow
while resizing CQ”) is missing part of the commit log message and one
of the SOB lines. The original patch was from Leon Romanovsky, and a
cut-n-paste separator in the commit message confused patchworks which
then put the end of message separator in the wrong place in the
downloaded patch, and I didn’t notice in time. The patch made it into
the official branch, and the only way to fix it in-place was to
rebase. Given the pain that a rebase causes, and the fact that the
patch has relevant tags for stable and syzkaller, a revert of the
munged patch and a reapplication of the original patch with the log
message intact was done.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (25 commits)
RDMA/mlx5: Fix integer overflow while resizing CQ
Revert "RDMA/mlx5: Fix integer overflow while resizing CQ"
RDMA/ucma: Check that user doesn't overflow QP state
RDMA/mlx5: Fix integer overflow while resizing CQ
RDMA/ucma: Limit possible option size
IB/core: Fix possible crash to access NULL netdev
RDMA/bnxt_re: Avoid Hard lockup during error CQE processing
RDMA/core: Reduce poll batch for direct cq polling
IB/mlx5: Fix an error code in __mlx5_ib_modify_qp()
IB/mlx5: When not in dual port RoCE mode, use provided port as native
IB/mlx4: Include GID type when deleting GIDs from HW table under RoCE
IB/mlx4: Fix corruption of RoCEv2 IPv4 GIDs
RDMA/qedr: Fix iWARP write and send with immediate
RDMA/qedr: Fix kernel panic when running fio over NFSoRDMA
RDMA/qedr: Fix iWARP connect with port mapper
RDMA/qedr: Fix ipv6 destination address resolution
IB/core : Add null pointer check in addr_resolve
RDMA/bnxt_re: Fix the ib_reg failure cleanup
RDMA/bnxt_re: Fix incorrect DB offset calculation
RDMA/bnxt_re: Unconditionly fence non wire memory operations
...
The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.
To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.
Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ok GACT action, TERMINATE binding_cmd should be used in action set
passed down to HW.
Fixes: b2925957ec ("mlxsw: spectrum_flower: Offload "ok" termination action")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.
This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.
The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause configuration will be set to default value by hclge_tm_schd_init
during reset, which causes the RSS configuration loss problem.
This patch fixes it by calling hclge_tm_init_hw during reset process
, which will set the pause configuration to default value.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.
This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the hclge_get/set_rss_tuple function
in order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the hclge_get/set_rss function in
order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a linked list to associate user-facing context IDs with FW-facing
context IDs (since the latter can change after an MC reset).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid doing useless work by making sure that the response_list is not empty
before scheduling work to process it.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected length check when data received in the mbox is more than one
64 bit data value
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaoH8zAAoJEEg/ir3gV/o+h00H/RyM1xoGCzJtvQAYEhNcEfvY
YJfaJSPvuuvS2Fvs8meUzjqQvKcmkMjmViD3Ujuzyh6Y36IcoPWlBojRDE2fpz2b
yRaK5CotcLpfDXchlLnH5ZZbOgO374866viCVoM4i2ls19Ml730piDs8CDcA6+T7
3W4vvr977xl9bFqDMMbeldijZ3+H36Exnq6Xj+o2j6Sc1/om9Mvgw7XJhcpiBTW5
ZFfA7djz7TdSyBJDQsLteL/wLbLsLeqXmKCKX9BsqRo+rpoUWmskKFNC1Dj0bzX3
XbrdR8GoHVMS1PZAPJIbc1bubhqBznxrbh/g95PInSkGZzKKWw1dhS/3fkkAndM=
=Fodq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-2 (IPSec-2)
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During a device failover or partition migration reset, it is not
necessary to disable the backing adapter since it should not be
running yet and its Command-Response Queue is closed. Sending
device commands during this time could result in an error or
timeout disrupting the reset process. In these cases, just halt
transmissions, clean up resources, and continue with reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function to halt network operations and clean up any
unused or outstanding socket buffers. Then, during device close,
disable backing adapter before halting all queues and performing
cleanup. This ensures all backing device operations will be
stopped before the driver cleans up shared resources.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some dead code now that RX pools are being cleaned. This
was included to wait until any pending RX queue interrupts are
processed, but NAPI polling should be disabled by this point.
Another minor change is to use the net device parameter for any
print functions instead of accessing it from the adapter structure.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver should alloc netdev with max support ring num, as
driver support change netdev count by ethtool -L.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command HCLGE_OPC_CFG_COM_TQP_QUEUE should use queue id in the
function, but command HCLGE_OPC_RESET_TQP_QUEUE should use global
queue id.
This patch fixes the queue id about queue enable/disable/reset.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the endian issue when PF get mbx message flag.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver should get the real rss_size which is assigned
by host PF, not rss_size_max.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ESN is not supported with IPSec device offload.
This patch adds ESN support to IPsec device offload.
Implementing new xfrm device operation to synchronize offloading device
ESN with xfrm received SN. New QP command to update SA state at the
following:
ESN 1 ESN 2 ESN 3
|-----------*-----------|-----------*-----------|-----------*
^ ^ ^ ^ ^ ^
^ - marks where QP command invoked to update the SA ESN state
machine.
| - marks the start of the ESN scope (0-2^32-1). At this point move SA
ESN overlap bit to zero and increment ESN.
* - marks the middle of the ESN scope (2^31). At this point move SA
ESN overlap bit to one.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New function for getting driver internal sa entry from xfrm state.
All checks are done in one function.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to add a context to the FPGA, we need to get both the software
transform context (which includes the keys, etc) and the
source/destination IPs (which are included in the steering
rule). Therefore, we register new set of firmware like commands for
the FPGA. Each time a rule is added, the steering core infrastructure
calls the FPGA command layer. If the rule is intended for the FPGA,
it combines the IPs information with the software transformation
context and creates the respective hardware transform.
Afterwards, it calls the standard steering command layer.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code has one layer that executed FPGA commands and
the Ethernet part directly used this code. Since downstream patches
introduces support for IPSec in mlx5_ib, we need to provide some
abstractions. This patch refactors the accel code into one layer
that creates a software IPSec transformation and another one which
creates the actual hardware context.
The internal command implementation is now hidden in the FPGA
core layer. The code also adds the ability to share FPGA hardware
contexts. If two contexts are the same, only a reference count
is taken.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds V2 command support.
New fpga devices support extended features (udp encap, esn etc...), this
features require new hardware sadb format therefore we have a new version
of commands to manipulate it.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current hardware decrypts and authenticates incoming ESP packets.
Subsequently, the software extracts the nexthdr field, truncates the
trailer and adjusts csum accordingly.
With this patch and a capable device, the trailer is being removed
by the hardware and the nexthdr field is conveyed via PET. This way
we avoid both the need to access the trailer (cache miss) and to
compute its relative checksum, which significantly improve
the performance.
Experiment shows that trailer removal improves the performance by
2Gbps, (netperf). Both forwarding and host-to-host configurations.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code assume only SA QP commands.
Refactor in order to pave the way for new QP commands:
1. Generic cmd response format.
2. SA cmd checks are in dedicated functions.
3. Aligned debug prints.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix build break of mlx5_accel_ipsec_device_caps is not defined when
MLX5_ACCEL is not selected, use MLX5_IPSEC_DEV instead which handles
such case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Remove VLA usage and change the 'len' argument to a u8 and use a 256
byte buffer on the stack. Notice that these lengths are limited by the
encoding field in the VPD structure, which is a u8 [1].
[1] https://marc.info/?l=linux-netdev&m=152044354814024&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJan4UmAAoJEEg/ir3gV/o+cZwH/1xBpdLsmeqEimwQ41bAc9Rj
UmPZXXMyQVUYfGOiE1aLTH7YNi38XWSnTFMN7HklMeX/9YKxUZNG8YuiO9iQhE1B
rUqRKfYFz9oFrUh95SzeclaunTpKrhYKHjQ9/u9nBMfI3H2Fy+y2NUBjIqJ6nysz
op3EwRcX5kD4+MjRum24XLUnMSYbg05mHCZKTDj5/2T4x+/j0XQqvvmWWinIt8BO
R4d7XGGywGjbhtcG1j+XBcFeLsEZnS/w70hoN38TdcmNWvokl1pGk8DVDii9i7GX
c5jQj2h5WG/bdsS26y8MFfWpoAn3Qzzm4W4OYwp/vmL7n/Llvq0GRCEKCi8AlA0=
=LeYV
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RX rings can fit most of the time in a contiguous piece of memory,
so lets use kvzalloc_node/kvfree instead of vzalloc_node/vfree
Note that kvzalloc_node() automatically falls back to another node,
there is no need to do the fallback ourselves.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel