Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_lookup and fib6_table_lookup to take a fib6_result and set
f6i and nh rather than returning a fib6_info. For now both always
return 0.
A later patch set can make these more like the IPv4 counterparts and
return EINVAL, EACCESS, etc based on fib6_type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_mtu_from_fib6 and fib6_mtu to take a fib6_result over a
fib6_info. Update both to use the fib6_nh from fib6_result.
Since the signature of ip6_mtu_from_fib6 is already changing, add const
to daddr and saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.
Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.
Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.
This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_forward_alloc's updating is also done on rx path, but to be consistent
we change to use sk_mem_charge() in sctp_skb_set_owner_r().
In sctp_eat_data(), it's not enough to check sctp_memory_pressure only,
which doesn't work for mem_cgroup_sockets_enabled, so we change to use
sk_under_memory_pressure().
When it's under memory pressure, sk_mem_reclaim() and sk_rmem_schedule()
should be called on both RENEGE or CHUNK DELIVERY path exit the memory
pressure status as soon as possible.
Note that sk_rmem_schedule() is using datalen to make things easy there.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rxrpc_kernel_check_life() pass back the life counter through the
argument list and return true if the call has not yet completed.
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the SKB list implementation assumption can be removed.
And now that we know that the list head is always non-NULL
we can remove the code blocks dealing with that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace NF_HOOK() based invocation of the netfilter hooks with a private
copy of nf_hook_slow().
This copy has one difference: it can return the rx handler value expected
by the stack, i.e. RX_HANDLER_CONSUMED or RX_HANDLER_PASS.
This is needed by the next patch to invoke the ebtables
"broute" table via the standard netfilter hooks rather than the custom
"br_should_route_hook" indirection that is used now.
When the skb is to be "brouted", we must return RX_HANDLER_PASS from the
bridge rx input handler, but there is no way to indicate this via
NF_HOOK(), unless perhaps by some hack such as exposing bridge_cb in the
netfilter core or a percpu flag.
text data bss dec filename
3369 56 0 3425 net/bridge/br_input.o.before
3458 40 0 3498 net/bridge/br_input.o.after
This allows removal of the "br_should_route_hook" in the next patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
rt6_probe sends probes for gateways in a nexthop. As such it really
depends on a fib6_nh, not a fib entry. Move last_probe to fib6_nh and
update rt6_probe to a fib6_nh struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only reason for having two different register functions was because of
ipt_MASQUERADE and ip6t_MASQUERADE being two different modules.
Previous patch merged those into xt_MASQUERADE, so we can merge this too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Both are now implemented by nf_nat_masquerade.c, so no need to keep
different headers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
fcntl(fd, F_SETOWN, getpid()) selects the recipient of SIGURG signals
that are delivered when out-of-band data arrives on socket fd.
If an SMC socket program makes use of such an fcntl() call, it fails
in case of fallback to TCP-mode. In case of fallback the traffic is
processed with the internal TCP socket. Propagating field "file" from the
SMC socket to the internal TCP socket fixes the issue.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reports that tls triggers warnings related to
sk->sk_forward_alloc not being zero at destruction time:
WARNING: CPU: 5 PID: 6831 at net/core/stream.c:206 sk_stream_kill_queues+0x103/0x110
WARNING: CPU: 5 PID: 6831 at net/ipv4/af_inet.c:160 inet_sock_destruct+0x15b/0x170
When sender fills up the write buffer and dies from
SIGPIPE. This is due to the device implementation
not cleaning up the partially_sent_record.
This is because commit a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
moved the partial record cleanup to the SW-only path.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This revert commit 46b1c18f9d ("net: sched: put back q.qlen into
a single location").
After the previous patch, when a NOLOCK qdisc is enslaved to a
locking qdisc it switches to global stats accounting. As a consequence,
when a classful qdisc accesses directly a child qdisc's qlen, such
qdisc is not doing per CPU accounting and qlen value is consistent.
In the control path nobody uses directly qlen since commit
e5f0e8f8e4 ("net: sched: introduce and use qdisc tree flush/purge
helpers"), so we can remove the contented atomic ops from the
datapath.
v1 -> v2:
- complete the qdisc_qstats_atomic_qlen_dec() ->
qdisc_qstats_cpu_qlen_dec() replacement, fix build issue
- more descriptive commit message
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stats updating is always consistent with TCQ_F_CPUSTATS flag,
we can disable it at qdisc creation time flipping such bit.
In my experiments, if the NOLOCK flag is cleared, per CPU stats
accounting does not give any measurable performance gain, but it
waste some memory.
Let's clear TCQ_F_CPUSTATS together with NOLOCK, when enslaving
a NOLOCK qdisc to 'lock' one.
Use stats update helper inside pfifo_fast, to cope correctly with
TCQ_F_CPUSTATS flag change.
As a side effect, q.qlen value for any child qdiscs is always
consistent for all lock classfull qdiscs.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core sched implementation checks independently for NOLOCK flag
to acquire/release the root spin lock and for qdisc_is_percpu_stats()
to account per CPU values in many places.
This change update the last few places checking the TCQ_F_NOLOCK to
do per CPU stats accounting according to qdisc_is_percpu_stats()
value.
The above allows to clean dev_requeue_skb() implementation a bit
and makes stats update always consistent with a single flag.
v1 -> v2:
- do not move qdisc_is_empty definition, fix build issue
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for root qdisc queue length, do not access directly q.qlen.
In the following patches we will move back qlen accounting to per CPU
values for NOLOCK qdiscs.
Instead, prefer the qdisc_is_empty() helper usage.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
-----BEGIN PGP SIGNATURE-----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=2EV9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_VIA and allow an IPv6 nexthop for v4 routes:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 via inet6 2001:db8::1 dev eth0
For convenience and simplicity, userspace can use RTA_VIA to specify
AF_INET or AF_INET6 gateway.
The common fib_nexthop_info dump function compares the gateway address
family to the nh_common family to know if the gateway should be encoded
as RTA_VIA or RTA_GATEWAY.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until support is added to the offload drivers, they need to be able to
reject routes with an IPv6 gateway. To that end add a flag to fib_info
that indicates if any fib_nh has a v6 gateway. The flag allows the drivers
to efficiently know the use of a v6 gateway without walking all fib_nh
tied to a fib_info each time a route is added.
Update mlxsw and rocker to reject the routes with extack message as to why.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common theme in the output path is looking up a neigh entry for a
nexthop, either the gateway in an rtable or a fallback to the daddr
in the skb:
nexthop = (__force u32)rt_nexthop(rt, ip_hdr(skb)->daddr);
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
To allow the nexthop to be an IPv6 address we need to consider the
family of the nexthop and then call __ipv{4,6}_neigh_lookup_noref based
on it.
To make this simpler, add a ip_neigh_gw4 helper similar to ip_neigh_gw6
added in an earlier patch which handles:
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
And then add a second one, ip_neigh_for_gw, that calls either
ip_neigh_gw4 or ip_neigh_gw6 based on the address family of the gateway.
Update the output paths in the VRF driver and core v4 code to use
ip_neigh_for_gw simplifying the family based lookup and making both
ready for a v6 nexthop.
ipv4_neigh_lookup has a different need - the potential to resolve a
passed in address in addition to any gateway in the rtable or skb. Since
this is a one-off, add ip_neigh_gw4 and ip_neigh_gw6 diectly. The
difference between __neigh_create used by the helpers and neigh_create
called by ipv4_neigh_lookup is taking a refcount, so add rcu_read_lock_bh
and bump the refcnt on the neigh entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch allows an IPv6 gateway with an IPv4 route. The neighbor
entry will exist in the v6 ndisc table and the cached header will contain
the ipv6 protocol which is wrong for an IPv4 packet. For an IPv4 packet to
use the v6 neighbor entry, neigh_output needs to skip the cached header
and just use the output callback for the neigh entry.
A future patchset can look at expanding the hh_cache to handle 2
protocols. For now, IPv6 gateways with an IPv4 route will take the
extra overhead of generating the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to fib_config. Since a gateway is either
IPv4 or IPv6, make it a union with fc_gw4 where fc_gw_family decides
which address is in use. Update current checks on family and gw4 to
handle ipv6 as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to rtable, fib_config needs to allow the gateway to be either an
IPv4 or an IPv6 address. To that end, rename fc_gw to fc_gw4 to mean an
IPv4 address and add fc_gw_family. Checks on 'is a gateway set' are changed
to see if fc_gw_family is set. In the process prepare the code for a
fc_gw_family == AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the gateway in a fib_nh_common to be from a different address
family than the outer fib{6}_nh. To that end, replace nhc_has_gw with
nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family.
Now nhc_family is used to know if the nh_common is part of a fib_nh
or fib6_nh (used for container_of to get to route family specific data),
and nhc_gw_family represents the address family for the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6 helpers to handle ndisc references via the stub. Update
bpf_ipv6_fib_lookup to use __ipv6_neigh_lookup_noref_stub instead of
the open code ___neigh_lookup_noref with the stub.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_nh_init and fib6_nh_release to ipv6_stubs. If fib6_nh_init fails,
callers should not invoke fib6_nh_release, so there is no reason to have
a dummy stub for the IPv6 is not enabled case.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT_NEEDED is true whenever nat support for either ipv4 or ipv6 is
enabled. Now that the af-specific nat configuration switches have been
removed, IS_ENABLED(CONFIG_NF_NAT) has the same effect.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
very little code, so it really doesn't make sense to have extra
modules or even a kconfig knob for this.
Merge them and make functionality available unconditionally.
The merge makes inet family route support trivial, so add it
as well here.
Before:
text data bss dec hex filename
835 832 0 1667 683 nft_chain_route_ipv4.ko
870 832 0 1702 6a6 nft_chain_route_ipv6.ko
111568 2556 529 114653 1bfdd nf_tables.ko
After:
text data bss dec hex filename
113133 2556 529 116218 1c5fa nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need minimal support from the nat core for this, as we do not
want to register additional base hooks.
When an inet hook is registered, interally register ipv4 and ipv6
hooks for them and unregister those when inet hooks are removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipip packets are blocked in some public cloud environments, this patch
allows gue encapsulation with the tunneling method, which would make
tunneling working in those environments.
Signed-off-by: Jacky Hu <hengqing.hu@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After commit a297569fe0 ("net/udp: do not touch skb->peeked unless
really needed") the 'peeked' argument of __skb_try_recv_datagram()
and friends is always equal to !!'flags & MSG_PEEK'.
Since such argument is really a boolean info, and the callers have
already 'flags & MSG_PEEK' handy, we can remove it and clean-up the
code a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_{err,warn}_ratelimited will be used by rt2x00
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is similar to commit e285d5bfb7 ("NFC: Fix the number of pipes")
where we changed NFC_HCI_MAX_PIPES from 127 to 128.
As the comment next to the define explains, the pipe identifier is 7
bits long. The highest possible pipe is 127, but the number of possible
pipes is 128. As the code is now, then there is potential for an
out of bounds array access:
net/nfc/nci/hci.c:297 nci_hci_cmd_received() warn: array off by one?
'ndev->hci_dev->pipes[pipe]' '0-127 == 127'
Fixes: 11f54f2286 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink_compat_switch_id_get() helper which fills up switch_id
according to passed netdev pointer. Call it directly from
dev_get_port_parent_id() as a fallback when ndo_get_port_parent_id
is not defined for given netdev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save space in the struct, convert bools to bits.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export fib_nexthop_info and fib_add_nexthop for use by IPv6 code.
Remove rt6_nexthop_info and rt6_add_nexthop in favor of the IPv4
versions. Update fib_nexthop_info for IPv6 linkdown check and
RTA_GATEWAY for AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the ipv4 code only needs data from fib_nh_common. Add
fib_nh_common selection to fib_result and update users to use it.
Right now, fib_nh_common in fib_result will point to a fib_nh struct
that is embedded within a fib_info:
fib_info --> fib_nh
fib_nh
...
fib_nh
^
fib_result->nhc ----+
Later, nhc can point to a fib_nh within a nexthop struct:
fib_info --> nexthop --> fib_nh
^
fib_result->nhc ---------------+
or for a nexthop group:
fib_info --> nexthop --> nexthop --> fib_nh
nexthop --> fib_nh
...
nexthop --> fib_nh
^
fib_result->nhc ---------------------------+
In all cases nhsel within fib_result will point to which leg in the
multipath route is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern