Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
So one of the constification patches unearthed a type casting fragility
of the underlying code:
276c870547 ("x86/platform/intel-mid: Make 'bt_sfi_data' const")
converted the struct to be const while it is also used as a temporary
container for important data that is used to fill 'parent' and 'name'
fields in struct platform_device_info.
The compiler doesn't notice this due to an explicit type cast that loses
the const - which fragility will be fixed separately.
This type cast turned a seemingly trivial const propagation patch into a
hard to debug data corruptor and crasher bug.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: julia.lawall@lip6.fr
Cc: platform-driver-x86@vger.kernel.org
Link: http://lkml.kernel.org/r/20171228122523.21802-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
EFI_OLD_MEMMAP's efi_call_phys_prolog() calls set_pgd() with swapper PGD that
has PAGE_USER set, which makes PTI set NX on it, and therefore EFI can't
execute it's code.
Fix that by forcefully clearing _PAGE_NX from the PGD (this can't be done
by the pgprot API).
_PAGE_NX will be automatically reintroduced in efi_call_phys_epilog(), as
_set_pgd() will again notice that this is _PAGE_USER, and set _PAGE_NX on
it.
Tested-by: Dimitri Sivanich <sivanich@hpe.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1801052215460.11852@cbobk.fhfr.pm
Commit:
82c3768b8d ("efi/capsule-loader: Use a cached copy of the capsule header")
... refactored the capsule loading code that maps the capsule header,
to avoid having to map it several times.
However, as it turns out, the vmap() call we ended up removing did not
just map the header, but the entire capsule image, and dropping this
virtual mapping breaks capsules that are processed by the firmware
immediately (i.e., without a reboot).
Unfortunately, that change was part of a larger refactor that allowed
a quirk to be implemented for Quark, which has a non-standard memory
layout for capsules, and we have slightly painted ourselves into a
corner by allowing quirk code to mangle the capsule header and memory
layout.
So we need to fix this without breaking Quark. Fortunately, Quark does
not appear to care about the virtual mapping, and so we can simply
do a partial revert of commit:
2a457fb31d ("efi/capsule-loader: Use page addresses rather than struct page pointers")
... and create a vmap() mapping of the entire capsule (including header)
based on the reinstated struct page array, unless running on Quark, in
which case we pass the capsule header copy as before.
Reported-by: Ge Song <ge.song@hxt-semitech.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Tested-by: Ge Song <ge.song@hxt-semitech.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 82c3768b8d ("efi/capsule-loader: Use a cached copy of the capsule header")
Link: http://lkml.kernel.org/r/20180102172110.17018-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull irq fixes from Thomas Gleixner:
"A rather large update after the kaisered maintainer finally found time
to handle regression reports.
- The larger part addresses a regression caused by the x86 vector
management rework.
The reservation based model does not work reliably for MSI
interrupts, if they cannot be masked (yes, yet another hw
engineering trainwreck). The reason is that the reservation mode
assigns a dummy vector when the interrupt is allocated and switches
to a real vector when the interrupt is requested.
If the MSI entry cannot be masked then the initialization might
raise an interrupt before the interrupt is requested, which ends up
as spurious interrupt and causes device malfunction and worse. The
fix is to exclude MSI interrupts which do not support masking from
reservation mode and assign a real vector right away.
- Extend the extra lockdep class setup for nested interrupts with a
class for the recently added irq_desc::request_mutex so lockdep can
differeniate and does not emit false positive warnings.
- A ratelimit guard for the bad irq printout so in case a bad irq
comes back immediately the system does not drown in dmesg spam"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
x86/vector: Use IRQD_CAN_RESERVE flag
genirq: Introduce IRQD_CAN_RESERVE flag
genirq/msi: Handle reactivation only on success
gpio: brcmstb: Make really use of the new lockdep class
genirq: Guard handle_bad_irq log messages
kernel/irq: Extend lockdep class for request mutex
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Kernel page table isolation requires to have two PGDs. One for the kernel,
which contains the full kernel mapping plus the user space mapping and one
for user space which contains the user space mappings and the minimal set
of kernel mappings which are required by the architecture to be able to
transition from and to user space.
Add the necessary preliminaries.
[ tglx: Split out from the big kaiser dump. EFI fixup from Kirill ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: hughd@google.com
Cc: keescook@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 PTI preparatory patches from Thomas Gleixner:
"Todays Advent calendar window contains twentyfour easy to digest
patches. The original plan was to have twenty three matching the date,
but a late fixup made that moot.
- Move the cpu_entry_area mapping out of the fixmap into a separate
address space. That's necessary because the fixmap becomes too big
with NRCPUS=8192 and this caused already subtle and hard to
diagnose failures.
The top most patch is fresh from today and cures a brain slip of
that tall grumpy german greybeard, who ignored the intricacies of
32bit wraparounds.
- Limit the number of CPUs on 32bit to 64. That's insane big already,
but at least it's small enough to prevent address space issues with
the cpu_entry_area map, which have been observed and debugged with
the fixmap code
- A few TLB flush fixes in various places plus documentation which of
the TLB functions should be used for what.
- Rename the SYSENTER stack to CPU_ENTRY_AREA stack as it is used for
more than sysenter now and keeping the name makes backtraces
confusing.
- Prevent LDT inheritance on exec() by moving it to arch_dup_mmap(),
which is only invoked on fork().
- Make vysycall more robust.
- A few fixes and cleanups of the debug_pagetables code. Check
PAGE_PRESENT instead of checking the PTE for 0 and a cleanup of the
C89 initialization of the address hint array which already was out
of sync with the index enums.
- Move the ESPFIX init to a different place to prepare for PTI.
- Several code moves with no functional change to make PTI
integration simpler and header files less convoluted.
- Documentation fixes and clarifications"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/cpu_entry_area: Prevent wraparound in setup_cpu_entry_area_ptes() on 32bit
init: Invoke init_espfix_bsp() from mm_init()
x86/cpu_entry_area: Move it out of the fixmap
x86/cpu_entry_area: Move it to a separate unit
x86/mm: Create asm/invpcid.h
x86/mm: Put MMU to hardware ASID translation in one place
x86/mm: Remove hard-coded ASID limit checks
x86/mm: Move the CR3 construction functions to tlbflush.h
x86/mm: Add comments to clarify which TLB-flush functions are supposed to flush what
x86/mm: Remove superfluous barriers
x86/mm: Use __flush_tlb_one() for kernel memory
x86/microcode: Dont abuse the TLB-flush interface
x86/uv: Use the right TLB-flush API
x86/entry: Rename SYSENTER_stack to CPU_ENTRY_AREA_entry_stack
x86/doc: Remove obvious weirdnesses from the x86 MM layout documentation
x86/mm/64: Improve the memory map documentation
x86/ldt: Prevent LDT inheritance on exec
x86/ldt: Rework locking
arch, mm: Allow arch_dup_mmap() to fail
x86/vsyscall/64: Warn and fail vsyscall emulation in NATIVE mode
...
Since uv_flush_tlb_others() implements flush_tlb_others() which is
about flushing user mappings, we should use __flush_tlb_single(),
which too is about flushing user mappings.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andrew Banman <abanman@hpe.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: hughd@google.com
Cc: keescook@google.com
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull misc x86 fixes from Ingo Molnar:
- make CR4 handling irq-safe, which bug vmware guests ran into
- don't crash on early IRQs in Xen guests
- don't crash secondary CPU bringup if #UD assisted WARN()ings are
triggered
- make X86_BUG_FXSAVE_LEAK optional on newer AMD CPUs that have the fix
- fix AMD Fam17h microcode loading
- fix broadcom_postcore_init() if ACPI is disabled
- fix resume regression in __restore_processor_context()
- fix Sparse warnings
- fix a GCC-8 warning
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Change time() prototype to match __vdso_time()
x86: Fix Sparse warnings about non-static functions
x86/power: Fix some ordering bugs in __restore_processor_context()
x86/PCI: Make broadcom_postcore_init() check acpi_disabled
x86/microcode/AMD: Add support for fam17h microcode loading
x86/cpufeatures: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
x86/idt: Load idt early in start_secondary
x86/xen: Support early interrupts in xen pv guests
x86/tlb: Disable interrupts when changing CR4
x86/tlb: Refactor CR4 setting and shadow write
Functions x86_vector_debug_show(), uv_handle_nmi() and uv_nmi_setup_common()
are local to the source and do not need to be in global scope, so make them
static.
Fixes up various sparse warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Cc: travis@sgi.com
Link: http://lkml.kernel.org/r/20171206173358.24388-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert all allocations that used a NOTRACK flag to stop using it.
Link: http://lkml.kernel.org/r/20171007030159.22241-3-alexander.levin@verizon.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Hansen <devtimhansen@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Pull x86 cleanups from Ingo Molnar:
"Two changes: Propagate const/__initconst, and use ARRAY_SIZE() some
more"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/events/amd/iommu: Make iommu_pmu const and __initconst
x86: Use ARRAY_SIZE
EFI data is encrypted when the kernel is run under SEV. Update the
page table references to be sure the EFI memory areas are accessed
encrypted.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: linux-efi@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20171020143059.3291-8-brijesh.singh@amd.com
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the ARRAY_SIZE macro improves the readability of the code.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-video@atrey.karlin.mff.cuni.cz
Cc: Martin Mares <mj@ucw.cz>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: https://lkml.kernel.org/r/20171001193101.8898-13-jeremy.lefaure@lse.epita.fr
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
Pull i2c updates from Wolfram Sang:
- new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS
- quite some driver updates
- cleanups for the i2c-mux subsystem
- some subsystem-wide constification
- further cleanup of include/linux/i2c
* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
i2c: sprd: Fix undefined reference errors
i2c: nomadik: constify amba_id
i2c: versatile: Make i2c_algo_bit_data const
i2c: busses: make i2c_adapter_quirks const
i2c: busses: make i2c_adapter const
i2c: busses: make i2c_algorithm const
i2c: Add Spreadtrum I2C controller driver
dt-bindings: i2c: Add Spreadtrum I2C controller documentation
i2c-cht-wc: make cht_wc_i2c_adap_driver static
MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
blackfin: merge the two TWI header files
i2c: davinci: Preserve return value of devm_clk_get
i2c: mediatek: Add i2c compatible for MediaTek MT7622
dt-bindings: i2c: Add MediaTek MT7622 i2c binding
dt-bindings: i2c: modify information formats
i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Transparently fall back to other poweroff method(s) if EFI poweroff
fails (and returns)
- Use separate PE/COFF section headers for the RX and RW parts of the
ARM stub loader so that the firmware can use strict mapping
permissions
- Add support for requesting the firmware to wipe RAM at warm reboot
- Increase the size of the random seed obtained from UEFI so CRNG
fast init can complete earlier
- Update the EFI framebuffer address if it points to a BAR that gets
moved by the PCI resource allocation code
- Enable "reset attack mitigation" of TPM environments: this is
enabled if the kernel is configured with
CONFIG_RESET_ATTACK_MITIGATION=y.
- Clang related fixes
- Misc cleanups, constification, refactoring, etc"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/bgrt: Use efi_mem_type()
efi: Move efi_mem_type() to common code
efi/reboot: Make function pointer orig_pm_power_off static
efi/random: Increase size of firmware supplied randomness
efi/libstub: Enable reset attack mitigation
firmware/efi/esrt: Constify attribute_group structures
firmware/efi: Constify attribute_group structures
firmware/dcdbas: Constify attribute_group structures
arm/efi: Split zImage code and data into separate PE/COFF sections
arm/efi: Replace open coded constants with symbolic ones
arm/efi: Remove pointless dummy .reloc section
arm/efi: Remove forbidden values from the PE/COFF header
drivers/fbdev/efifb: Allow BAR to be moved instead of claiming it
efi/reboot: Fall back to original power-off method if EFI_RESET_SHUTDOWN returns
efi/arm/arm64: Add missing assignment of efi.config_table
efi/libstub/arm64: Set -fpie when building the EFI stub
efi/libstub/arm64: Force 'hidden' visibility for section markers
efi/libstub/arm64: Use hidden attribute for struct screen_info reference
efi/arm: Don't mark ACPI reclaim memory as MEMBLOCK_NOMAP
Don't populate arrays on the stack, instead make them static.
Makes the object code smaller by 76 bytes:
Before:
text data bss dec hex filename
4217 1540 128 5885 16fd arch/x86/platform/intel-mid/pwr.o
After:
text data bss dec hex filename
3981 1700 128 5809 16b1 arch/x86/platform/intel-mid/pwr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/20170825163206.23250-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This follows efi_mem_attributes(), as it's similarly generic. Drop
__weak from that one though (and don't introduce it for efi_mem_type()
in the first place) to make clear that other overrides to these
functions are really not intended.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170825155019.6740-5-ard.biesheuvel@linaro.org
[ Resolved conflict with: f99afd08a45f: (efi: Update efi_mem_type() to return an error rather than 0) ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Mark a couple of structures and functions as 'static', pointed out by Sparse:
warning: symbol 'bts_pmu' was not declared. Should it be static?
warning: symbol 'p4_event_aliases' was not declared. Should it be static?
warning: symbol 'rapl_attr_groups' was not declared. Should it be static?
symbol 'process_uv2_message' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Andrew Banman <abanman@hpe.com> # for the UV change
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/20170810155709.7094-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make this structure const as it is only used during copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: julia.lawall@lip6.fr
Link: http://lkml.kernel.org/r/1502039720-4471-1-git-send-email-bhumirks@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the future we would use dynamic allocation for IRQ which brings
non-1:1 mapping for IOAPIC domain. Thus, we need to respect return value
of mp_map_gsi_to_irq() and assign it back to the device structure.
Besides that we need to read GSI from interrupt pin register to avoid
cases when some drivers will try to initialize PCI device twice in a row
which will call pcibios_enable_irq() twice as well.
serial 0000:00:04.1: Mapped GSI28 to IRQ5
serial 0000:00:04.2: Mapped GSI29 to IRQ5
serial 0000:00:04.3: Mapped GSI54 to IRQ5
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ5
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ6
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ7
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20170724173402.12939-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Group timers callback initializers together in
x86_intel_mid_early_setup() for easy to find and maintain.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170724173309.12878-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The BAU confers no benefit to a UV system running with only one hub/socket.
Permanently disable the BAU driver if there are less than two hubs online
to avoid BAU overhead. We have observed failed boots on single-socket UV4
systems caused by BAU that are avoided with this patch.
Also, while at it, consolidate initialization error blocks and fix a
memory leak.
Signed-off-by: Andrew Banman <abanman@hpe.com>
Acked-by: Russ Anderson <rja@hpe.com>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: tony.ernst@hpe.com
Link: http://lkml.kernel.org/r/1500588351-78016-1-git-send-email-abanman@hpe.com
[ Minor cleanups. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have space for exactly three characters for the index in "max7315_%d_base",
but as GCC points out having more would cause an string overflow:
arch/x86/platform/intel-mid/device_libs/platform_max7315.c: In function 'max7315_platform_data':
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: error: '%d' directive writing between 1 and 11 bytes into a region of size 9 [-Werror=format-overflow=]
sprintf(base_pin_name, "max7315_%d_base", nr);
^~~~~~~~~~~~~~~~~
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: note: directive argument in the range [-2147483647, 2147483647]
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:3: note: 'sprintf' output between 15 and 25 bytes into a destination of size 17
sprintf(base_pin_name, "max7315_%d_base", nr);
This makes it use an snprintf() to truncate the string if that happened
rather than overflowing the stack. In practice, this is safe, because
there won't be a large number of max7315 devices in the systems, and
both the format and the length are defined by the firmware interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-9-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When SME is active, pagetable entries created for EFI need to have the
encryption mask set as necessary.
When the new pagetable pages are allocated they are mapped encrypted. So,
update the efi_pgt value that will be used in CR3 to include the encryption
mask so that the PGD table can be read successfully. The pagetable mapping
as well as the kernel are also added to the pagetable mapping as encrypted.
All other EFI mappings are mapped decrypted (tables, etc.).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Toshimitsu Kani <toshi.kani@hpe.com>
Cc: kasan-dev@googlegroups.com
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/9a8f4c502db4a84b09e2f0a1555bb75aa8b69785.1500319216.git.thomas.lendacky@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The efi_mem_type() function currently returns a 0, which maps to
EFI_RESERVED_TYPE, if the function is unable to find a memmap entry for
the supplied physical address. Returning EFI_RESERVED_TYPE implies that
a memmap entry exists, when it doesn't. Instead of returning 0, change
the function to return a negative error value when no memmap entry is
found.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Toshimitsu Kani <toshi.kani@hpe.com>
Cc: kasan-dev@googlegroups.com
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/7fbf40a9dc414d5da849e1ddcd7f7c1285e4e181.1500319216.git.thomas.lendacky@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bug fix for the BAU tunable congested_cycles not being set to the user
defined value. Instead of referencing a global variable when deciding
on BAU shutdown, a node will reference its own tunable set
value ( cong_response_us). This results in the user set
tunable value congested_response_us taking effect correctly.
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Acked-by: Andrew Banman <abanman@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mike.travis@hpe.com
Cc: sivanich@hpe.com
Link: http://lkml.kernel.org/r/1499970803-282432-1-git-send-email-justin.ernst@hpe.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The functions handle_uv2_busy, uv_flush_send_and_wait and
find_another_by_swack are local to the source, so make them static.
Also remove normal_busy as it is no longer used.
Fixes various smatch warnings, such as:
"symbol 'find_another_by_swack' was not declared. Should it be static?"
"symbol 'handle_uv2_busy' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Andrew Banman <abanman@hpe.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/20170704083129.10559-1-colin.king@canonical.com
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- Expand the generic infrastructure handling the irq migration on CPU
hotplug and convert X86 over to it. (Thomas Gleixner)
Aside of consolidating code this is a preparatory change for:
- Finalizing the affinity management for multi-queue devices. The
main change here is to shut down interrupts which are affine to a
outgoing CPU and reenabling them when the CPU comes online again.
That avoids moving interrupts pointlessly around and breaking and
reestablishing affinities for no value. (Christoph Hellwig)
Note: This contains also the BLOCK-MQ and NVME changes which depend
on the rework of the irq core infrastructure. Jens acked them and
agreed that they should go with the irq changes.
- Consolidation of irq domain code (Marc Zyngier)
- State tracking consolidation in the core code (Jeffy Chen)
- Add debug infrastructure for hierarchical irq domains (Thomas
Gleixner)
- Infrastructure enhancement for managing generic interrupt chips via
devmem (Bartosz Golaszewski)
- Constification work all over the place (Tobias Klauser)
- Two new interrupt controller drivers for MVEBU (Thomas Petazzoni)
- The usual set of fixes, updates and enhancements all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
irqchip/or1k-pic: Fix interrupt acknowledgement
irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap
irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity
nvme: Allocate queues for all possible CPUs
blk-mq: Create hctx for each present CPU
blk-mq: Include all present CPUs in the default queue mapping
genirq: Avoid unnecessary low level irq function calls
genirq: Set irq masked state when initializing irq_desc
genirq/timings: Add infrastructure for estimating the next interrupt arrival time
genirq/timings: Add infrastructure to track the interrupt timings
genirq/debugfs: Remove pointless NULL pointer check
irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID
irqchip/gic-v3-its: Add ACPI NUMA node mapping
irqchip/gic-v3-its-platform-msi: Make of_device_ids const
irqchip/gic-v3-its: Make of_device_ids const
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU
genirq/irqdomain: Remove auto-recursive hierarchy support
irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access
...
Pull x86 mm updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued work to add support for 5-level paging provided by future
Intel CPUs. In particular we switch the x86 GUP code to the generic
implementation. (Kirill A. Shutemov)
- Continued work to add PCID CPU support to native kernels as well.
In this round most of the focus is on reworking/refreshing the TLB
flush infrastructure for the upcoming PCID changes. (Andy
Lutomirski)"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
x86/mm: Delete a big outdated comment about TLB flushing
x86/mm: Don't reenter flush_tlb_func_common()
x86/KASLR: Fix detection 32/64 bit bootloaders for 5-level paging
x86/ftrace: Exclude functions in head64.c from function-tracing
x86/mmap, ASLR: Do not treat unlimited-stack tasks as legacy mmap
x86/mm: Remove reset_lazy_tlbstate()
x86/ldt: Simplify the LDT switching logic
x86/boot/64: Put __startup_64() into .head.text
x86/mm: Add support for 5-level paging for KASLR
x86/mm: Make kernel_physical_mapping_init() support 5-level paging
x86/mm: Add sync_global_pgds() for configuration with 5-level paging
x86/boot/64: Add support of additional page table level during early boot
x86/boot/64: Rename init_level4_pgt and early_level4_pgt
x86/boot/64: Rewrite startup_64() in C
x86/boot/compressed: Enable 5-level paging during decompression stage
x86/boot/efi: Define __KERNEL32_CS GDT on 64-bit configurations
x86/boot/efi: Fix __KERNEL_CS definition of GDT entry on 64-bit configurations
x86/boot/efi: Cleanup initialization of GDT entries
x86/asm: Fix comment in return_from_SYSCALL_64()
x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Add the SYSTEM_SCHEDULING bootup state to move various scheduler
debug checks earlier into the bootup. This turns silent and
sporadically deadly bugs into nice, deterministic splats. Fix some
of the splats that triggered. (Thomas Gleixner)
- A round of restructuring and refactoring of the load-balancing and
topology code (Peter Zijlstra)
- Another round of consolidating ~20 of incremental scheduler code
history: this time in terms of wait-queue nomenclature. (I didn't
get much feedback on these renaming patches, and we can still
easily change any names I might have misplaced, so if anyone hates
a new name, please holler and I'll fix it.) (Ingo Molnar)
- sched/numa improvements, fixes and updates (Rik van Riel)
- Another round of x86/tsc scheduler clock code improvements, in hope
of making it more robust (Peter Zijlstra)
- Improve NOHZ behavior (Frederic Weisbecker)
- Deadline scheduler improvements and fixes (Luca Abeni, Daniel
Bristot de Oliveira)
- Simplify and optimize the topology setup code (Lauro Ramos
Venancio)
- Debloat and decouple scheduler code some more (Nicolas Pitre)
- Simplify code by making better use of llist primitives (Byungchul
Park)
- ... plus other fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
sched/cputime: Refactor the cputime_adjust() code
sched/debug: Expose the number of RT/DL tasks that can migrate
sched/numa: Hide numa_wake_affine() from UP build
sched/fair: Remove effective_load()
sched/numa: Implement NUMA node level wake_affine()
sched/fair: Simplify wake_affine() for the single socket case
sched/numa: Override part of migrate_degrades_locality() when idle balancing
sched/rt: Move RT related code from sched/core.c to sched/rt.c
sched/deadline: Move DL related code from sched/core.c to sched/deadline.c
sched/cpuset: Only offer CONFIG_CPUSETS if SMP is enabled
sched/fair: Spare idle load balancing on nohz_full CPUs
nohz: Move idle balancer registration to the idle path
sched/loadavg: Generalize "_idle" naming to "_nohz"
sched/core: Drop the unused try_get_task_struct() helper function
sched/fair: WARN() and refuse to set buddy when !se->on_rq
sched/debug: Fix SCHED_WARN_ON() to return a value on !CONFIG_SCHED_DEBUG as well
sched/wait: Disambiguate wq_entry->task_list and wq_head->task_list naming
sched/wait: Move bit_wait_table[] and related functionality from sched/core.c to sched/wait_bit.c
sched/wait: Split out the wait_bit*() APIs from <linux/wait.h> into <linux/wait_bit.h>
sched/wait: Re-adjust macro line continuation backslashes in <linux/wait.h>
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Rework the EFI capsule loader to allow for workarounds for
non-compliant firmware (Ard Biesheuvel)
- Implement a capsule loader quirk for Quark X102x (Jan Kiszka)
- Enable SMBIOS/DMI support for the ARM architecture (Ard Biesheuvel)
- Add CONFIG_EFI_PGT_DUMP=y support for x86-32 and kexec (Sai
Praneeth)
- Fixes for EFI support for Xen dom0 guests running under x86-64
hosts (Daniel Kiper)"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen/efi: Initialize only the EFI struct members used by Xen
efi: Process the MEMATTR table only if EFI_MEMMAP is enabled
efi/arm: Enable DMI/SMBIOS
x86/efi: Extend CONFIG_EFI_PGT_DUMP support to x86_32 and kexec as well
efi/efi_test: Use memdup_user() helper
efi/capsule: Add support for Quark security header
efi/capsule-loader: Use page addresses rather than struct page pointers
efi/capsule-loader: Redirect calls to efi_capsule_setup_info() via weak alias
efi/capsule: Remove NULL test on kmap()
efi/capsule-loader: Use a cached copy of the capsule header
efi/capsule: Adjust return type of efi_capsule_setup_info()
efi/capsule: Clean up pr_err/_info() messages
efi/capsule: Remove pr_debug() on ENOMEM or EFAULT
efi/capsule: Fix return code on failing kmap/vmap
In preparation for an objtool rewrite which will have broader checks,
whitelist functions and files which cause problems because they do
unusual things with the stack.
These whitelists serve as a TODO list for which functions and files
don't yet have undwarf unwinder coverage. Eventually most of the
whitelists can be removed in favor of manual CFI hint annotations or
objtool improvements.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/7f934a5d707a574bda33ea282e9478e627fb1829.1498659915.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the fwnode to create a named domain so diagnosis works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.907511074@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
kernel/sched/Makefile
Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The kernel has several code paths that read CR3. Most of them assume that
CR3 contains the PGD's physical address, whereas some of them awkwardly
use PHYSICAL_PAGE_MASK to mask off low bits.
Add explicit mask macros for CR3 and convert all of the CR3 readers.
This will keep them from breaking when PCID is enabled.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/883f8fb121f4616c1c1427ad87350bb2f5ffeca1.1497288170.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CONFIG_EFI_PGT_DUMP=y, as the name suggests, dumps EFI page tables to the
kernel log during kernel boot.
This feature is very useful while debugging page faults/null pointer
dereferences to EFI related addresses.
Presently, this feature is limited only to x86_64, so let's extend it to
other EFI configurations like kexec kernel, efi=old_map and to x86_32 as well.
This doesn't effect normal boot path because this config option should
be used only for debug purposes.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602135207.21708-13-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The firmware for Quark X102x prepends a security header to the capsule
which is needed to support the mandatory secure boot on this processor.
The header can be detected by checking for the "_CSH" signature and -
to avoid any GUID conflict - validating its size field to contain the
expected value. Then we need to look for the EFI header right after the
security header and pass the real header to __efi_capsule_setup_info.
To be minimal invasive and maximal safe, the quirk version of
efi_capsule_setup_info() is only effective on Quark processors.
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602135207.21708-11-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rather than passing all the contents of flush_tlb_info to
flush_tlb_others(), pass a pointer to the structure directly. For
consistency, this also removes the unnecessary cpu parameter from
uv_flush_tlb_others() to make its signature match the other
*flush_tlb_others() functions.
This serves two purposes:
- It will dramatically simplify future patches that change struct
flush_tlb_info, which I'm planning to do.
- struct flush_tlb_info is an adequate description of what to do
for a local flush, too, so by reusing it we can remove duplicated
code between local and remove flushes in a future patch.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
[ Fix build warning. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For EFI with the 'efi=old_map' kernel option specified, the kernel will panic
when KASLR is enabled:
BUG: unable to handle kernel paging request at 000000007febd57e
IP: 0x7febd57e
PGD 1025a067
PUD 0
Oops: 0010 [#1] SMP
Call Trace:
efi_enter_virtual_mode()
start_kernel()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
The root cause is that the identity mapping is not built correctly
in the 'efi=old_map' case.
On 'nokaslr' kernels, PAGE_OFFSET is 0xffff880000000000 which is PGDIR_SIZE
aligned. We can borrow the PUD table from the direct mappings safely. Given a
physical address X, we have pud_index(X) == pud_index(__va(X)).
However, on KASLR kernels, PAGE_OFFSET is PUD_SIZE aligned. For a given physical
address X, pud_index(X) != pud_index(__va(X)). We can't just copy the PGD entry
from direct mapping to build identity mapping, instead we need to copy the
PUD entries one by one from the direct mapping.
Fix it.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Young <dyoung@redhat.com>
Cc: Frank Ramsay <frank.ramsay@hpe.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170526113652.21339-5-matt@codeblueprint.co.uk
[ Fixed and reworded the changelog and code comments to be more readable. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Booting kexec kernel with "efi=old_map" in kernel command line hits
kernel panic as shown below.
BUG: unable to handle kernel paging request at ffff88007fe78070
IP: virt_efi_set_variable.part.7+0x63/0x1b0
PGD 7ea28067
PUD 7ea2b067
PMD 7ea2d067
PTE 0
[...]
Call Trace:
virt_efi_set_variable()
efi_delete_dummy_variable()
efi_enter_virtual_mode()
start_kernel()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
[ efi=old_map was never intended to work with kexec. The problem with
using efi=old_map is that the virtual addresses are assigned from the
memory region used by other kernel mappings; vmalloc() space.
Potentially there could be collisions when booting kexec if something
else is mapped at the virtual address we allocated for runtime service
regions in the initial boot - Matt Fleming ]
Since kexec was never intended to work with efi=old_map, disable
runtime services in kexec if booted with efi=old_map, so that we don't
panic.
Tested-by: Lee Chun-Yi <jlee@suse.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170526113652.21339-4-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When booted as Xen dom0 there won't be an EFI memmap allocated. Avoid
issuing an error message in this case:
[ 0.144079] efi: Failed to allocate new EFI memmap
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170526113652.21339-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds