Currently number of tdls vdevs supported by firmware
is hardcoded. For future usage it is stored in ath10k
structure based on defined value.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware 10.2.4.48-3 now supports management frames over HTT feature and has
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX. But as 10.2.4 branch has conflicting HTT ids
patch "ath10k: add ATH10K_FW_IE_HTT_OP_VERSION" is needed to fix the issue.
Older ath10k versions don't have support that support and to maintain backwards
compatibility we need bump up the FW API to 5 not break older versions.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Target to host HTT messages are conflicting between 10.x and other
firmware revisions. By maintaining separate HTT T2H tables for each
firmware revisions (main, 10x and tlv) similar to WMI abstraction,
solves the conflicts. Add ATH10K_FW_IE_HTT_OP_VERSION so that the firmware can
advertise the HTT interface to ath10k.
This fix is needed to get management frames over HTT (ie.
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX disabled) working with 10.2.4.48-2 firmware.
Otherwise there will be unknown htt events and nothing works:
[30087.438343] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30087.448691] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30149.032974] ath10k_pci 0000:02:00.0: htt event (19) not handled
If the firmware does not have ATH10K_FW_IE_HTT_OP_VERSION use the main HTT
interface. That way old firmware images will still work.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current SKID length configuration causes firmware
to reject peer creation for not able to allocate
AST entries for peers. This issue is observed when
least significant 3 bytes are used ramdomly to create
client MAC addresses.
AST table SKID length configuration is increased to
maximum value to fix this issue.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A value of zero indicates that 128B is the maximum
DMA request size for read/writes. But PCI cards based
on AR9880 can support 256B, so enable this for
the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.
This prepares ath10k to support new hw.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was the final missing bit to making sure the
device doesn't assert interrupts to host.
This should fix possible race when target crashes
during driver teardown.
This also removes an early warm reset workaround
during pci probing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.
The calibration data is found by using the id string provided by dev_name()
using this format:
cal-<bus>-<id>.bin
With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:
/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin
The calibration data sequence is:
1. Check with request_firmware() if there's a calibration file
("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
not, goto 2
2. Check if otp.bin is able to successfully load the calibration data
from OTP. If yes, use that. If not, goto 3.
4. Print an error message that no calibration data found and stop driver
initialization for this device.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is required if we take into account possibility to load the driver
from initrd (RAM disk), so in other words: very early in the boot process,
before the file system is visible.
In such case we need to have the firmware files accessible from ram disk too,
and this patch guarantee this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful for collecting pktlog statistics of tx, rx
and rate information, so add tracing for the API call.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide calibration data used by the firmware to user space via a debugfs file.
This makes it easier to debug calibration related problems.
Example:
sudo cp /sys/kernel/debug/ieee80211/phy0/ath10k/cal_data 1.cal
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We do not really support older firmware API 1 anymore, so better remove
MODULE_FIRMWARE() declarations for them and only list for API 2 files.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k assumed all interrupts were directed to it.
This isn't the case for legacy shared interrupts.
ath10k consumed interrupts for other devices.
Check device irq status and return IRQ_NONE when
appropriate.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to oversight AP 10.X support was merged with
Ethernet RX decap mode.
Only Native Wifi RX decap mode guarantees IP
header is properly aligned and avoids sk_buff data
realignment (which is very expensive
performance-wise) in mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware IE containers can dynamically provide various information what
firmware supports. Also it can embed more than one image so updating firmware
is easy, user just needs to update one file in /lib/firmware/.
The firmware API 2 or higher will use the IE container format, the current API
1 will not use the new format but it still is supported for some time. FW API 2
files are named as firmware-2.bin (which contains both firmware and otp images)
and API 1 files are firmware.bin and otp.bin.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce all TARGET specific values for 10.x firmware.
Some of them are common for both firmwares we will support,
but to avoid confusion, define everything with prefix 10X_.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was corrupted and leading to compilation warning
core.c: In function 'ath10k_check_fw_version':
core.c:79: warning: comparison is always true due to limited range of data type
Since we are going to support new FW track in the driver,
the sanity check for fw version number would be an overkill
then. This is just for information purposes anyway.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ethernet-like decapping mode leaves IP protocol
frame not aligned to 4-byte boundaries. This leads
to re-aligning in mac80211 which in turn leads to
poor CPU cache behaviour on some machines.
Since HW doesn't allow to change payload offset
properly the solution is to force HW to decap in
Native Wifi mode which always has 24-bytes long
802.11 header (even for QoS frames). This means IP
frame is properly aligned in this decap mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.
To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:
[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95
Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware comes with new HTT protocol version.
In 3.0 the separate mgmt tx command has been
removed. All traffic is to be pushed through data
tx (tx_frm) command with a twist - FW seems to not
be able (yet?) to access tx fragment table so for
manamgement frames frame pointer is passed
directly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The latest supported and available FW build is 1.0.0.636.
Reflect this in ath10k code.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the firmware support is no longer available for hw1.0,
drop all code (especially workarounds) for those units.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior