The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.17 are:
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 892:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 888:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
To fix these bugs, usleep_range() is replaced with udelay().
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add functions for get_fecparam and set_fecparam.
2. Modify lio_get_link_ksettings to display FEC setting.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch and the MAC are in one IP core and they use the same clock
signal from the clock generation unit.
Currently the clock architecture in the lantiq SoC code does not allow
to easily share the same clocks, this has to be fixed by switching to
the common clock framework.
As a workaround the clock of the switch and MAC should be activated when
the MAC gets probed and only disabled when the MAC gets removed. This
way it is ensured that the clock is always enabled when the switch or
MAC is used. The switch can not be used without the MAC.
This fixes a data bus error when rebooting the system and deactivating
the switch and mac and later accessing some registers in the cleanup
while the clocks are disabled.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c:322:5: warning:
symbol 'hns_gmac_wait_fifo_clean' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In CXGB4_DCB_STATE_FW_INCOMPLETE state check if the dcb
version is changed and update the dcb supported version.
- Also, fill the priority code point value for priority
based flow control.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
print per rx-queue packet errors in sge_qinfo
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLA used for the emac xaht registers size. Since the size
of registers can only ever be 4 or 8, as detected in emac_init_config(),
the max can be hardcoded and a runtime test added for robustness.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Ivan Mikhaylov <ivan@de.ibm.com>
Cc: netdev@vger.kernel.org
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.
When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.
This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIV_ROUND_UP has implemented the code-opened function. Therefore, just
replace the implementation with DIV_ROUND_UP.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_pull_bc_msg':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:907:6: warning:
variable 'fw_mbx' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_issue_bc_post':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:939:16: warning:
variable 'hdr_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.
Change a few ANDs to ORs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
at 1G supported speeds to enable 1G MAC support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report in standard netdev stats drops and errors as well as
RX multicast from the FW vNIC counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the vlan id field is present when trying
to match a vlan tag. The vlan id and vlan pcp field should be treated
independently.
Fixes: 5571e8c9f2 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.
This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.
In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
!test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
...
If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.
So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra characters from the names of structures to unify prefixes
used through the driver code (we normally use hw_atl for hw specifics).
HW_ATL_B0_ and HW_ATL_A0_ are the same and useless copies.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra spaces, corrected alignment.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add WOL support. Currently only magic packet
(ethtool -s <ethX> wol g) feature is implemented.
Remove hw_set_power and move that to FW_OPS set_power:
because WOL configuration behaves differently on 1x and 2x
firmwares
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added definitions and structures needed to support WOL.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the upload function, which worked incorrectly with
some chips.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the changes in patch 1 and 2, droq lock is not required.
So removing droq lock.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed oom task unconditional rescheduling every 250ms and created per
queue oom work queue for refilling buffers.
The oom task refills only if the available descriptors is fallen to 64.
There will be no packets coming in after hitting this level. So NAPI will
not run until oom task refills the buffers.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control packets are processed in tasklet when interface is down and in
NAPI when interface is up. So tasklet can be disabled when interface up
and re-enabled when interface is down.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_zalloc_coherent() now crashes if no dev pointer is given.
Add a dev pointer to the ltq_dma_channel structure and fill it in the
driver using it.
This fixes a bug introduced in kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit updated vlan_cmd.dropnovlan_fm but failed to remove
the older assignment. Fix this by removing the former redundant
assignment.
Detected by CoverityScan, CID#1473290 ("Unused value")
Fixes: a89cdd8e7c ("cxgb4: impose mandatory VLAN usage when non-zero TAG ID")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added memory barriers where they were missing to support multiple
architectures, and removed redundant ones.
As part of removing the redundant memory barriers and improving
performance, we moved to more relaxed versions of memory barriers,
as well as to the more relaxed version of writel - writel_relaxed,
while maintaining correctness.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acquire the rtnl_lock during device destruction to avoid
using partially destroyed device.
ena_remove() shares almost the same logic as ena_destroy_device(),
so use ena_destroy_device() and avoid duplications.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing